Tender For Routine Operation, Maintenance And Providing Civil & Electrical Maintenance (Including Facility Management Services) For Office And/Or Residential Complex At Amlohri Project (For The Period Of 2 Years)., Singrauli-Madhya Pradesh

TDR : 55676638

Tender Notice
BOQ

18 Days Left

Singrauli , Madhya Pradesh

Tender Brief : Tender For Routine Operation, Maintenance And Providing Civil & Electrical Maintenance (Including Facility Management Services) For Office And/Or Residential Complex At Amlohri Project (For The Period Of 2 Years).

Document Fees
Refer document

EMD
₹ 1980100.0 /-

Tender Value
₹ 15.84 Crore /-

Submission Date
15-06-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Chlorination
2	Supply of liquid chlorine( Hypochlorite base formulation) for treatment of drinking water purpose confirming to IS 10500: 1991
3	Horticulture
4	Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly leveling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).
5	Renovating lawns including weeding, cheeling the grass, forking the ground,top dressing with sludge or manure, mixing the same with forked soil,watering and maintaining the lawn for 60 days or more till the grass forms a thick lawn free from weeds and fit for mowing and disposal of rubbish as directed, including supplying good earth if needed but excluding the cost of sludge or manure (The manure/sludge shall be paid for separately)
6	Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure orextra earth to be paid for separately)
7	Supplying and stacking of good earth at site including royalty and carriage upto 5 km complete (earth measured in stacks will be reduced by 20% for payment).
8	Supplying and stacking of well decayed cattle manure at site including royalty and carriage upto 5 k.m. lead complete (cattle manure measured in stacks will reduced by 8% for Payment).
9	Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.
10	Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared.
11	Cutting of Hedge/Edge including removing of cut material, cleaning, hoeing of hedge/edge bed watering, manureing and applying insecticides and fungicides etc.(excluding the cost of material which shall be supplied by the department) and as per direction of officer in charge
12	Complete maintenance of shrubs (Out side garden features), jobs like making of basin at regular interval i/c watering, weeding, pruning & application of fertilizer etc, (excluding the cost of material which shall be supplied by the department) and as per direction of officer in charge
13	Maintenance of potted plant Earthen pot in displayed at ground floor only in bungalow,office complex including application of good earth, manure, insecticide, pesticide and fertilizer, removing of dry parts by pruning, cleaning dry leaves and displaying in appropriate place and replacement of broken pots coloring of pots and change of location of pots and replacing with fresh plants as and when required ( Materials shall be provided by the department) as per direction of officer in charge
14	Maintenance of potted plants Cement pots at ground floor in flats and ground floor bungalow,office complex including application of good earth, manure, insecticide, pesticide and fertilizer, removing of dry parts by pruning,cleaning dry leaves and displaying in appropriate place and replacement of broken pots coloring of pots and change of location of pots and replacing with fresh plants as and when required (Materials shall be provided by the department) as per direction of officer in charge
15	Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately)
16	Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge
17	Providing and displaying of Araucaria cookie plant, having ht. 60 cm to 75 cm, straight, well developed, fresh and healthy with lush green leaves from bottom to top in 20 cm size of Earthen pot / Plastic pot. & as per direction of the officer-in-charge.
18	Providing and displaying of Areca Palm plant, having ht. 90 cm to 1.20 m with 4 to 5 suckers, well developed, fresh and healthy with lush green foliage in 25 cm size of Earthen pot / Plastic pot & as per direction of the officer-in-charge
19	Providing and displaying of Chamaedorea elegans palm plant, having ht. 60 cm to 75 cm, well developed with fresh and healthy leaves in 25 cm size of Earthen pot / Plastic pot . & as per direction of the officer-in-charge
20	Providing and displaying of Croton Baby Golden Punctatumaureum plant, having ht. 23 cm to 30 cm, well developed with fresh and healthy foliage in 15 cm size of Earthen pot / Plastic pot. as per direction of the officer-incharge
21	Providing and displaying of Croton petra Banglore variety plant, having ht 45 cm & above, well developed with fresh and healthy leaves in 20 cm size of Earthen pot / Plastic pot. & as per direction of the officer-in-charge
22	Providing and displaying of Phoenix palm plant, having ht. 75 cm to 90 cm with 10 to 15 or more leaves, well developed, fresh and healthy in 25 cm size of Earthen pot / Plastic pot & as per direction of the officer-in-charge
23	Providing and displaying of Raphis palm plant, having ht. 45 cm to 60 cm with 5 to 7 suckers, well developed, full of fresh and healthy leaves in 25 cm size of Earthen pot / Plastic pot & as per direction of the officer-incharge.
24	Providing and Displaying Bougainvillea named variety, Sobhra, Thima, Marry palmar, Cherry Blossom etc. well developed with fresh & healthy bushy plant in full bloom 75 to 90 cm ht. in 40 cm Cement Pot as per direction of the officer-in-charge
25	Providing and Displaying Cycus revoluta in 35 cm challi, specimen plant, having 30 to 40 with fresh and healthy, leaves having 25cm to 30cm circumfrance of base stem well developed as per direction of the officer-in-charge
26	Providing and Displaying Traveller palm plant well developed with fresh & healthy foliage 120 to 150 cm ht. in 35 cm Cement Pot as per direction of the officer-in-charge
27	Providing and Displaying Adenium Obesum grafted plant well developed with fresh & healthy 30 to 60 cm ht. in 25 cm size Earthen Pot/ Plastic Pot as per direction of the officer-in-charge
28	Providing and stacking of Euphorbia milli hybrid variety plant, having ht.30 cm to 45 cm with multi branch, full bloom, fresh and healthy leaves in 20 cm size of Earthen Pot / Plastic Pot & as per direction of the officer-incharge
29	Supply and stacking of Bottle palm plant of ht. 150-180 cm bottom girth 20-25 cm well developed in big poly bags of size 25 cm as per direction of the officer-in-charge
30	Supply and stacking of plant Mussaenda erythrophylla (Rosea) of height 60-75 cm. multi branched in earthen pots of size 25 cm as per direction of the officer-in-charge
31	Supply and stacking of plant Thuja compacta of height 45-60 cm., well branched in earthen pots of size 25 cm as per direction of the officer-in-charge
32	Supply and stacking of Passiflora caerulea (Rakhi bel) plant of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge
33	Supply and stacking of Clerodendrum thompsonae plant of height 30 cm.to 45 cm in 20 cm size of poly bag & as per direction of the officer-in-charge
34	Carriage of Materials by mechanical transport including loading,unloading and stacking: Lead up to 1 km Lime, moorum, building rubbish
35	Providing and stacking of winter seasonal seedling/cutting at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge.Alyssum
36	Providing and stacking of winter seasonal seedling/cutting at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Cineraria dwarf hybrid
37	Providing and stacking of winter seasonal seedling/cutting at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Dahlia double
38	Providing and stacking of winter seasonal seedling/cutting at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Dianthus hybrid
39	Providing and stacking of winter seasonal seedling/cutting at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Gerbera hybrid double
40	Providing and stacking of winter seasonal seedling/cutting at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Antirrhinum dwarf
41	Providing and stacking of winter seasonal seedling/cutting at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Marigold Inca hybrid
42	Providing and stacking of winter seasonal seedling/cutting at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Nasturtium
43	Providing and stacking of winter seasonal seedling/cutting at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Pansy Hybrid
44	Providing and stacking of winter seasonal seedling/cutting at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Petunia hybrid
45	Providing and stacking of winter seasonal seedling/cutting at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Phlox mix colour hybrid
46	Providing and stacking of winter seasonal seedling/cutting at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Poppy double
47	Providing and stacking of winter seasonal seedling/cutting at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Salvia Hybrid different colour
48	Providing and stacking of winter seasonal seedling/cutting at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Aster dwarf
49	Providing and stacking of winter seasonal seedling/cutting at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Calendula double
50	Providing and stacking of winter seasonal seedling/cutting at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Chrysanthemum double
51	Providing and stacking of summer & rainy seasonal seedling at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge.Balsam seedling
52	Providing and stacking of summer & rainy seasonal seedling at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge.Zinnia hybrid
53	Providing and stacking of summer & rainy seasonal seedling at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge.Celosia argentea & Celosia crostata Hybrid
54	Providing and stacking of summer & rainy seasonal seedling at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge.Cosmos hybrid
55	Providing and stacking of summer & rainy seasonal seedling at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge.Gaillardia Double
56	Providing and stacking of summer & rainy seasonal seedling at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Kochia
57	Providing and stacking of summer & rainy seasonal seedling at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge.Portulaca hybrid
58	Providing and stacking of summer & rainy seasonal seedling at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge.Vinca Hybrid
59	Budded Rose (H.T. variety) 3 to 4 healthy branch 30 cm and above ht. welldeveloped with one and above flower in 20 cm Earthen Pot,
60	Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) : Holes 60 cm dia, and 60 cm deep
61	Providing Circular Cement Concrete pots of specified size, cast with cement concrete of nominal mix 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate 6 mm nominal size), reinforced with 7 Nos ( 3 nos horizontal & 4 nos vertical “ U “ shape) M.S. wires of 3.5 mm dia as per design, including required form work, finishing with cement punning on exposed surface, curing for specified period and stacking in required rows & height, all complete as per direction of Officer-in-charge Top inside dia 30 cm, outer bottom dia 20 cm, total height 30 cm with wall thickness of 25.4 mm
62	Filling of the following size empty pots with mixture of good earth & manure in the ratio of 2:1 (Two part of Good earth & one port of manure) and placing them on appropriate place i/c carriage of earth, manure and pots up to 50 mtr, as per direction of officer incharge. (The cost of good earth, earthenpots & manure will be paid separately.)Size of Empty Pots 35cm Top dia, 25cm Bottom Dia & 35cm Perpendicular height
63	Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, hedge, flower beds, foliages, creepers etc. including hoeing,weeding pruning replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter , removal of garden waste, applying insecticide, pesticide & fertilizers (whenever required) top dressing of lawn with good earth and menure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide , Pesticide will be provided by the Department & lawn mover and brush cutter with fuel , other T & P material/articles shall be provided by the contractor.) 2.40.1 Permanent office accommodation (as per yard stick 1Mali =1.25Acre)
64	Permanent office accommodation. (as per yard stick 1Mali =1.25Acre)
65	Prestigious works/H.M.house & officers entitled to free accommodation
66	Play grounds / Public parks (as per yard stick 1Mali =2.00Acre)
67	Complete maintenance of trees (Out side garden features), jobs like making of basin at regular interval i/c watering, weeding, pruning & application of fertilizer etc, (excluding the cost of material which shall be supplied by the department) and as per direction of officer in charge Trees for 250 no/(up to 4 & up to 3 year Slow & Fast growing group)
68	Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) Trees Plant
69	Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) Shrubs Plant
70	Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) Hedge Plant
71	Horticulture Part B
72	Bonemeal
73	Malathion
74	Neem Cake
75	Rogar 30%
76	Rose Mixture
77	Sarso Khali
78	Civil Mainetenance
79	Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.
80	Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming ,watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :All kinds of soil Pipes, cables etc, not exceeding 80 mm dia.
81	Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, includinggetting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming ,watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :All kinds of soil Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia
82	Excavating, supplying and filling of local earth (including royalty) by mechanicaltransport up to a lead of 5km,rammingandwatering of the earth inlayers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.
83	Extra for levelling & neatly dressing of disposed soil completely as directed by Engineer-in-charge.
84	Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer’s specification.
85	Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation leveling and dressing and finishing the top smooth.
86	Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but, excluding cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size).
87	Providing and fixing sliding arrangement in racks/ cupboards/cabinets shutter by with stainless steel rollers to run inside C or E aluminium channel section (The payment of C or E channel shall be made separately).
88	Providing and fixing 50 mm bright finished brass cup board or wardrobe knob of approved quality with necessary screws
89	Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.
90	Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.
91	Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc.complete:125x75x4 mm
92	Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete:75x63x4 mm
93	Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
94	Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
95	Welding by gas or electric plant including transportation of plant at site etc. complete.
96	Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
97	Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc., complete.
98	Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 600x600 mm
99	Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer- in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
100	Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.0.63 mm thick with zinc coating not less than 275 gm/ m²
101	Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete.0.63 mm thick with zinc coating not less than 275 gm/m²
102	Painting top of roofs with bitumen of approved quality @ 17kg per 10 sqm impregnated with a coat of coarse sand at 60 cudm per 10 sqm, including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete :With residual type petroleum bitumen of grade VG -10
103	Removing and uprooting of unwanted vegetation grown over the drainage pipe, walls, chhajjas, balcony and similar location of building upto floor Vth level with all tools & plants required with safety precaution and making good the same with plaster including disposal of material/tree roots etc. at the required place all complete as per instruction of EIC.
104	Providing and fixing M.S. round or square bars with M.S. flats at required spacing in wooden frames of windows and clerestory windows
105	Cleaning and desilting of gully trap chamber, including removal of rubbish mixed with earth etc. and disposal of same, all as per the direction of Engineer-in-charge.
106	Disconnecting damaged overhead / terrace PVC water storage tank of any size from water supply line and removing from the terrace including shifting at ground level as per direction of Engineer-in- charge.
107	Providing & fixing White vitreous china water closet squatting pan (Indian type) along with \\"S\\" or \\"P\\" trap including dismantling of old WC seat and \\"S\\" or \\"P\\" trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge.Orissa pattern W.C Pan of size 580x440 mm
108	Cutting holes of required size in brick masonry wall for fixing of exhaust fan including providing and fixing 300 mm dia PVC pipe conforming BIS-12818 and making good the same etc. complete as per direction of Engineer-in-charge.
109	Hacking of CC flooring including cleaning for surface etc. complete as per direction of the Engineer-in-Charge.
110	Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in- Charge.
111	Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually / by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge :15 mm to 40 mm nominal bore
112	Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge :Above 40 mm nominal bore
113	Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid
114	Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
115	lettering with black Japan paint of approved brand and manufacture
116	Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge.
117	Small petty carpentary work such as small repair of doors, windows, making hole, fixing of miscellaneous fixtures etc.
118	Renewing glass panes, with putty and nails wherever necessary including racking out the old putty:Renewal of old putty of glass panes (length).
119	Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.
120	Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground for lead up to 10km for all lifts, complete as per direction of EIC.
121	Providing and fixing white vitreous china pedestal type (European type/ wash down type) water closet pan.
122	Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan.
123	Providing and fixing 100 mm sand cast Iron grating for gully trap.
124	Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
125	Providing and fixing PTMT shelf 440 mm long, 124 mm width and 36 mm height of approved quality and colour, weighing not less than 300 gms.
126	Carriage of materials by mechanical transport including loading, unloading and stacking at dump area.Lime, moorum ,building rubbish.Lead up to 1.00 km.
127	CARRIAGE OF MATERIALS Carriage of material by Mechanical Transport including loading, unloading and stackingEarth Lead - 1 Km
128	Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge.
129	Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)
130	Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.
131	Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. M.S. tube.
132	Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using flats 30x6mm for diagonal braces and central cross piece.
133	Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.
134	Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick.
135	Granite of stone slab colour and shade Area of slab over 0.50 sqm
136	Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i)Single socketed pipes. 75 mm diameter
137	Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i)Single socketed pipes. 110 mm diameter
138	Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion. Coupler 75mm
139	Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion. Coupler 110mm
140	Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion. Bend 87.5° 75 mm bend
141	Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion. Bend 87.5° 110 mm bend
142	Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion. Shoe (Plain) 75 mm Shoe
143	Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion. Shoe (Plain) 110 mm Shoe
144	Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hardwood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 75 mm
145	Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hardwood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm
146	12 mm cement plaster of mix : 1:4 (1 cement:4 fine sand)
147	12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)
148	6 mm cement plaster of mix : 1:3 (1 cement: 3 fine sand)
149	White washing with lime to give an even shade : New work (three or more coats).
150	Colour washing such as green, blue or buff to give an even shade : New work (two or more coats) with a base coat of white washing with lime
151	Applying priming coat : With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)
152	Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work.
153	12 mm cement plaster finished with a floating coat of neat cement of mix 1:4 (1 cement: 4 fine sand)
154	Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground within 50 metres lead : With cement mortar 1:4 (1 cement : 4 fine sand).
155	White washing with lime to give an even shade : Old work (two or more coats) .
156	White washing with lime to give an even shade : Old work (one or more coats)
157	Distempering with 1st quality acrylic distember (Ready mix) having VOC content less than 50 grams/ litre of approved brand and manufacture to give an even shade Old work (one or more coats)
158	Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of thickness 4 mm.
159	Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of thickness 5.5 mm .
160	Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade : One or more coats on old work.
161	Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work
162	French spirit polishing : One or more coats on old work.
163	Finishing walls with Acrylic Smooth exterior paint of required shade:Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface
164	Finishing walls with Acrylic Smooth exterior paint of required shade:Old work (One or more coat applied @ 0.90 ltr/10 sqm).
165	Cleaning of terrace/loft water storage tank (inside surface area) upto 2000 litre capacity at all heights with coconut brushes, duster etc., removal of silt, rubbish from the tank and cleaning the tank with fresh water disinfecting with bleaching powder @ 0.5gm per litre capacity of tank, including marking the date of cleaning on the side of tank body with the help of stencil and paint and disposing of malba, all complete as per direction of Engineer-in-Charge. (The old date already written on tank should be removed with paint remover or black paint and if date is not written with the stencil or old date is not removed deduction will be made @ Rs. 0.10 per litre if during cleaning any GI fittings or ball cock is damaged that is to be repaired by contractor at his own cost and nothing extra will be paid on this account)
166	Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead: Of area 3 sq. metres and below
167	Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)
168	Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.15.23.1 For thickness of tiles 10 mm to 25 mm.
169	Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.. In cement mortar
170	Providing and fixing white vitreous china water closet squatting pan (Indian type) : Orissa pattern W.C. pan of size 580x440 mm
171	Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap
172	Providing and fixing kitchen sink including making all connections excluding cost of fittings. White glazed fire clay sink of size 600x450x250 mm
173	Providing and fixing soil, waste and vent pipes : 100 mm dia. Sand cast iron S&S pipe as per IS: 1729.
174	Providing and fixing soil, waste and vent pipes : 75 mm diameter : Sand cast iron S&S pipe as per IS: 1729.
175	Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes :75 mm dia pipe
176	Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes :100 mm dia pipe
177	Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. :For 100 mm dia pipe
178	Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. :For 75 mm dia pipe
179	Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.100 mm diaSand cast iron S&S as per IS - 1729
180	Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.75 mm diaSand cast iron S&S as per IS - 1729
181	Providing and fixing double equal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete :100x100x100x100 mmSand cast iron S&S as per IS - 1729
182	Providing and fixing double equal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete :75x75x75x75 mmSand cast iron S&S as per IS - 1729
183	Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.100x100x100 mmSand cast iron S&S as per IS - 1729
184	Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.75x75x75 mmSand cast iron S&S as per IS - 1729
185	Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :100 mm inlet and 100 mm outletSand Cast Iron S&S as per IS: 1729
186	Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 15 mm dia nominal bore
187	Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 20 mm dia nominal bore
188	Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work.25 mm dia nominal bore
189	Cutting holes up to 30x30 cm in walls including making good the same: With common burnt clay F.P.S. (non modular) bricks.
190	Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.All kinds of soil
191	Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil
192	Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)
193	Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20 mm nominal size)
194	Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominalsize).
195	Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level. Cold twisted bars
196	Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.
197	Trimming of tree branches in colony/plant and near boundary wall including disposal of brances outside the periphery of the colony and plant area as per instruction of EIC.
198	Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia. & length (hold fast lugs or dash fastener shall be paid for separately). Kiln seasoned and chemically treated hollock wood
199	Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm
200	Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 75 mm
201	Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.Twin rubber stopper.
202	Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC ‘C’ channel of size 30mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the ‘C’ Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer’s specification & drawing. 30 mm thick plain PVC door shutters.
203	Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.1.0 mm thick
204	Deduct for not providing hinges in doors, windows or clerestory window shutters with : Stainless steel butt hinges with stainless steel screws : For 2nd class teak wood and other class of wood shutters.
205	Providing and fixing flat pressed 3 layer particle board medium density exterior grade (Grade I) or graded wood particle board IS : 3087 marked, to frame, backing or studding with screws etc. complete (Frames, backing or studding to be paid separately): 18 mm thick
206	Providing and fixing Pre-laminated flat pressed 3 layer (medium density) particle board or graded wood particle board IS : 3087 marked, with one side decorative and other side balancing lamination Grade I, Type II exterior grade IS : 12823 marked, in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately). 18 mm thick .
207	Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters : 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.
208	Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:25 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
209	Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels plates etc including weilding, grinding buffing poilshing and making curvature( Whever requried) and fitting with necessary accessories & stainless stell dash fasteners, stainless stell bolts etc of requried size on the top of floor or side of waist slap with suitable arrangement as per approval of EIC ( for apyment purpose only weight of stainless steel members shall be considered excluding fixing caccessories susch as nuts bolts and fasterners)
210	Providing and fixing hand rail of approved size by weilding etc to steel ladder railing balcony railing stair case railing and similar works including applying priming coat of approved steel primer M.S. tube
211	Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment).Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)
212	Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws: 30 mm thick shutters. With ISI marked stainless steel butt hinges of required size - Kiln seasoned and chemically treated hollock wood.
213	Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets : 20 mm dia (heavy type)
214	Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding
215	Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. Kiln seasoned and chemically treated hollock wood. 30 mm thick shutters
216	Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 lever sand a pair of lever handles of approved quality with necessary screws etc. complete.
217	Providing and fixing 18 mm thick, 150 mm wide pelmet of flat pressed 3 layer or graded wood particle board medium density grade I, IS : 3087 marked, including top cover of 6 mm commercial ply wood conforming to IS: 303 BWR grade, nickel plated M.S. pipe 20 mm dia ( heavy type) curtain rod with nickel plated brackets, including fixing with 25x3 mm M.S. flat 10 cm long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm x 40 mm on both inner side of pelmet and rawl plugs 75 mm long etc. all complete.
218	Providing and fixing hard drawn steel wire fabric 75x25 mm mesh of weight not less than 7.75 Kg per sqm to window frames etc. including 62x19 mm beading of second class teak wood and priming coat with approved steel primer all complete.
219	Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. With 2nd class teak wood beading 62X19 mm
220	Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete.Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides
221	Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. complete : 100x58x1.90 mm
222	Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. complete : 75x47x1.70 mm
223	Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. complete :50x37x1.50 mm
224	Providing M.S. Piano hinges ISI marked IS : 3818 finished with nickel plating and fixing with necessary screws etc., complete. Overall width 35 mm.
225	Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete :300x16 mm
226	Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : 250x16 mm
227	Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 250x10 mm
228	Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 150x10 mm
229	Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 100x10 mm
230	Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : 125 mm
231	Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :250x16 mm.
232	Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :200x10 mm
233	Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :100x10 mm
234	Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : 100 mm
235	Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete :75 mm .
236	Providing and fixing oxidised M.S. hasp and staple (safety type) conforming to IS : 363 with necessary screws etc. complete : 150 mm
237	Providing and fixing oxidised M.S. hasp and staple (safety type) conforming to IS : 363 with necessary screws etc. complete : 90 mm
238	Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick: Kiln seasoned and chemically treated hollock wood.
239	Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 25 mm thick with 12.5 mm nominal size stone aggregate
240	Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry
241	Cleaning of CI/AC chocked pipe 100 mm diameter
242	Providing and fixing steel grating jali 100 mm
243	Half brick work with non-modular fly -ash-lime brick (FALG bricks) confirming to IS: 12894,class designation 7.5 average compressive strength etc. complete in all respect in foundation & plinth in cement morter 1:4(1 cement: 4 coarse sand)
244	Half brick work with non-modular fly -ash-lime brick (FALG bricks) confirming to IS: 12894,class designation 7.5 average compressive strength etc. complete in all respect in super-structure above plinth level up to floor V level in in cement morter 1:4(1 cement:4 coarse sand)
245	Brick work with non-modular fly -ash-lime brick (FALG bricks) confirming to IS: 12894,class designation 7.5 average compressive strength etc. complete in all respect in foundation & plinth in cement morter 1:6(1 cement: 6 coarse sand)
246	Brick work with non-modular fly -ash-lime brick (FALG bricks) confirming to IS: 12894,class designation 7.5 average compressive strength etc. complete in all respect in super-structure above plinth level up to floor V level in in cement morter 1:6(1 cement: 6 coarse sand)
247	Random rubble masonry with hard stone in superstructure above plinth level and upto floor five level, including leveling up with cement concrete 1:6:12 (1 cement : 6 coarsesand : 12 graded stone aggregate 20 mm nominal size) at window sills, ceiling level and the like.Cement mortar 1:6 (1 cement : 6 coarse sand)
248	Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of selfpriming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineerin-Charge.
249	Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)
250	Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)
251	For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)
252	Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer- in-charge. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side
253	Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)
254	Roof top water tank cleaning
255	Cleaning of roof top water tank, including draining out water, cleaning, disinfecting the tank by bleaching powder etc. and washing the tanks with fresh water, writing of cleaning date with paint on the outer face of the tank all complete with tools, tackles and consumables as per instruction of EIC
256	Cleaning of ground water reservoir/ over head tank including scraping of stains and muck from wall & floor and removal of muck from reservoir, disinfecting the tank by lime/bleaching powder etc, and washing the tank with fresh water, writing the cleaning date with paint on the outer surface of the tank all complete with tools, tackles and consumables as per instruction of EIC
257	Upkeeping and Sanitation
258	Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.
259	Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared.
260	Carriage of materials by Mechanical Transport including loading, unloading and stacking- lead up to 1km- Lime, moorum, building rubbish
261	CARRIAGE OF MATERIALS Carriage of material by Mechanical Transport including loading, unloading and stackingEarth Lead - 5 Km
262	Carriage of materials by Mechanical Transport including loading, unloading and stacking- lead up to 1km- Manure or sludge
263	Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift upto1.5 m. - All kinds of soil.
264	Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50m and lift up to 1.5m,as directed by Engineer-in-Charge. : All kinds of soil
265	Cleaning of surface drain including disposal of muck/ sludge through trolley or other arrangements to a specified place (in no case it shall be kept on drain banks) with in a lead of 1 KM complete with all tools & tackles as per instruction of EIC.- Up to 300mm wide
266	Cleaning of surface drain including disposal of muck/ sludge through trolley or other arrangements to a specified place (in no case it shall be kept on drain banks) with in a lead of 1 KM complete with all tools & tackles as per instruction of EIC.- Above 300 mm & up to 600 mm wide
267	Cleaning of surface drain including disposal of muck/ sludge through trolley or other arrangements to a specified place (in no case it shall be kept on drain banks) with in a lead of 1 KM complete with all tools & tackles as per instruction of EIC.- Above 600mm wide
268	Collection of garbage from door to door & disposal of the same through trolley or other suitable arrangement to the sprcified place within a lead of 1 KM including sweeping of staircase (for 1st and 2nd floor qtrs) with all tools and tackles as per instruction of EIC.- Ground Floor
269	Collection of garbage from door to door & disposal of the same through trolley or other suitable arrangement to the sprcified place within a lead of 1 KM including sweeping of staircase (for 1st and 2nd floor qtrs) with all tools and tackles as per instruction of EIC.- First Floor
270	Collection of garbage from door to door & disposal of the same through trolley or other suitable arrangement to the sprcified place within a lead of 1 KM including sweeping of staircase (for 1st and 2nd floor qtrs) with all tools and tackles as per instruction of EIC.- Second Floor
271	Cleaning of toilet including WC pan, wash basin, other fittings if any for \\"B\\" & lower type quarters by hand dusting and cleaning with soap solution, acids and phenyl etc. to make the toilet clean & hygienic all complete with tools, tackles as per instruction of EIC.
272	Cleaning of toilet including WC pan, wash basin, other fittings if any for C type quarters by hand dusting and cleaning with soap solution, acids and phenyl etc. to make the toilet clean & hygienic all complete with tools, tackles as per instruction of EIC.
273	Cleaning of toilet including WC pan, wash basin, other fittings if any for D type quarters by hand dusting and cleaning with soap solution, acids and phenyl etc. to make the toilet clean & hygienic all complete with tools, tackles as per instruction of EIC.
274	Cleaning of toilet attached with hostel rooms, office chambers etc including cleaning of floors, skirting & dado, WC pan (Indian/European type), wash basin, shelves, mirror and other fittings, if any, by hand dusting and cleaning with soap solution, acids, deodorants, phenyl etc to make the toilet clean and hygienic and providing nepthalene balls in urinals complete with all tools, tackles & consumables as per instruction of EIC (for community and service building)
275	brooming cleaning of all roads in colony and within premises of service building and other places as required with all tools & tackles and stacking the garbage at specified place as per instruction of EIC
276	Cleaning of general/ common toilet including cleaning of wc pan (indian /European type) wash basin,urinals by hand dusting and cleaning with shop salution acids, deodarent phenyl etc to make the toilet clean and hyginic and providing naphthalene balls in urinals complete with all tools trackles & consumables as per instructions EIC
277	Cleaning of all type of roof including removal of dry leaves, weedings and cleaning drain holes, brooming etc all complete with tools & tackles and stacking the garbage at specified places as per instruction of EIC
278	Cleaning, mopping & washing of floor of public buildings, other places neatly with detergents, bleaching powder etc all complete with tools, tackles and consumable to make the floor clean & hygienic as per instruction of EIC
279	Cleaning of door shutter, window shutters including chowkhats, window grills, glass panes, cabwebs etc of service/community buildings with necessary detergents, chemical etc complete as per instruction of EIC
280	Disposal of dead animal including transportation to the specified place, making earth pit, disposal of dead animal into with adequate quantity of salt lime, bleaching powder etc and refilling the pit with earth all complete with tools, tackles and consumables as per instruction of EIC. - Small animal (Dog, cat, fox, pig, birds and the like)
281	Disposal of dead animal including transportation to the specified place, making earth pit, disposal of dead animal into with adequate quantity of salt lime, bleaching powder etc and refilling the pit with earth all complete with tools, tackles and consumables as per instruction of EIC. - Big animal (Cow, Buffalo, Ox, and the like)
282	Felling trees of the girth (measured at a height of 1 m above ground level), including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material.Above 240 cm girth
283	Water Supply
284	Regular operation controlling valves providing in water supply pipe line to various sector of residential quarter service building situated in Permanent township including operation of pump with T&P all Complete as per EIC ( Filter 3 nos, Valve man 10 Nos) in all three shift.
285	Providing and fixing corner glass shelf(with bracket) of Jaguar make or equivalent.(ACN-1173)
286	Providing and fixing single lever wall mixer with provision of hand shower ,but without hand shower( Jaguar make or equivalent)(KUP-35119PM)
287	Providing and fixing Maze overhead shower 300mm round shape single flow(body & face plate stainless steel with chrome finish)with rubit cleaning system ( Jaguar make or equivalent)(OHS-CHR-1633)
288	Providing and fixing rimless single piece Wc with UF soft close seat cover,tornado flushing ,hinges, fixing accessories set,cistern fittings,S-trap 300mm. ( Jaguar make or equivalent)(OPS-WHT-15851SN)
289	P&F wall under counter wash basin oval shape of Jaguar make or equivalent complete in all respect as per EIC.
290	Providing and fixing swivel mirror of Jaguar make or equivalent.(ACN-1195N)
291	Providing and fixing towel rack with lower hanger (stainless steel)with hook.Jaguar make or equivalent(AHS-1581H)
292	P&F CP brass bib cock of Jaguar make or equivalent complete in all respect as per EIC.
293	P&F CP brass Angular stop cock of Jaguar make or equivalent complete in all respect as per EIC.
294	P&F CP brass waste coupling of Jaguar make or equivalent complete in all respect as per EIC.
295	P&F PVC water tank cover including fixing and fiiting complete in all respect
296	Providing Sunmica for wood work as per instruction of EIC.
297	Providing and fixing Aquafree urinal Kit (Hindware make or equivalent) for water less urinals complete in all respect as per instruction of EIC
298	Providing and fixing seat cover wall hung (WC) (Hindware make or equivalent) complete in all respect as instruction of EIC.
299	Labour rate for fixing G.I. pipes complete with G.I. fittings and making good the walls etc. Internal work - Exposed on wall 15 to 40 mm dia nominal bore
300	Labour rate for fixing M.S. round or square bars with M.S. flats at required spacing in wooden frames of windows and clerestory windows.
301	Providing and fixing bolts including nuts and washers complete.
302	Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively.
303	Providing and fixing 100 mm sand cast Iron grating for gully trap.
304	Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.
305	Supplying pig lead at site of work
306	Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
307	Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.
308	Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink without drain board. 610x460 mm bowl depth 200 mm
309	Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required : Size 600x450x200 mm
310	Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 10 litre capacity - White
311	Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete : White solid plastic seat with lid.
312	Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings :Flat back wash basin of size 630x450 mm.
313	Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings : Flat back wash basin of size 550x400 mm.
314	Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe. 32 mm dia
315	Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe. 40 mm dia
316	Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern
317	Providing and fixing C.P. Brass pillar cock
318	Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.17.73.1 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms each 390.20
319	Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.Internal work - Exposed on wall.15 mm dia nominal bore.
320	Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.Internal work - Exposed on wall.20 mm dia nominal bore.
321	Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.Internal work - Exposed on wall.25 mm dia nominal bore.
322	Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.Internal work - Exposed on wall.40 mm dia nominal bore.
323	Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. : External work 25 mm dia. nominal bore
324	Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. : External work 40 mm dia. nominal bore
325	Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.50 mm dia nominal bore.
326	Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.80 mm dia nominal bore.
327	Providing and fixing brass bib cock of approved quality :15 mm nominal bore.
328	Providing and fixing brass stop cock of approved quality :15 mm nominal bore.
329	Providing and fixing brass stop cock of approved quality :20 mm nominal bore.
330	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore.
331	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :40 mm nominal bore.
332	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 50 mm nominal bore
333	Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet.100 mm diameter.
334	Providing and laying S&S C.I. standard specials such as tees, bends, collars, tapers, caps etc. (Heavy class):Up to 300 mm dia.
335	Providing and laying flanged C.I. standard specials such as tees, bends, collars, tapers, caps etc., suitable for flanged jointing as per IS : 1538 :Up to 300 mm dia
336	Providing and laying S&S centrifugally cast (spun) iron pipes (Class LA) conforming to IS - 1536 :100 mm dia pipe.
337	Providing and laying S&S centrifugally cast (spun) iron pipes (Class LA) conforming to IS - 1536 :150 mm dia pipe.
338	Providing and laying S&S centrifugally cast (spun) iron pipes (Class LA) conforming to IS - 1536 :200 mm dia pipe.
339	Providing and laying S&S centrifugally cast (spun) iron pipes (Class LA) conforming to IS - 1536 :250 mm dia pipe.
340	Providing lead caulked joints to spun iron or C.I. pipes and specials, including testing of joints but excluding the cost of pig lead : 100 mm diameter pipe
341	Providing lead caulked joints to spun iron or C.I. pipes and specials, including testing of joints but excluding the cost of pig lead : 150 mm diameter pipe
342	Providing lead caulked joints to spun iron or C.I. pipes and specials, including testing of joints but excluding the cost of pig lead : 200 mm diameter pipe
343	Providing and fixing C.I. sluice valves (with cap ) complete with bolts, nuts, rubber insertions etc. ( the tail pieces if required will be paid separately ) : 100 mm diameter. Class I
344	Providing and fixing C.I. sluice valves ( with cap ) complete with bolts, nuts, rubber insertions etc. ( the tail pieces if required will be paid separately ) : 150 mm diameter. Class I
345	Providing and fixing C.I. sluice valves ( with cap ) complete with bolts, nuts, rubber insertions etc. ( the tail pieces if required will be paid separately ) : 200 mm diameter. Class I
346	Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) 15 mm nominal bore
347	Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) 20 mm nominal bore
348	Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) 25 mm nominal bore
349	Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) 40 mm nominal bore
350	Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) 50mm nominal bore
351	Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws, including excavation, refilling the earth or cutting of wall and making good the same complete wherever required : 15 mm nominal bore.
352	Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws, including excavation, refilling the earth or cutting of wall and making good the same complete wherever required : 20 mm nominal bore.
353	Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws, including excavation, refilling the earth or cutting of wall and making good the same complete wherever required : 25 mm nominal bore.
354	Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws, including excavation, refilling the earth or cutting of wall and making good the same complete wherever required : 40 mm nominal bore.
355	Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws, including excavation, refilling the earth or cutting of wall and making good the same complete wherever required :50 mm nominal bore.
356	Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws, including excavation, refilling the earth or cutting of wall and making good the same complete wherever required :80 mm nominal bore.
357	Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore.
358	Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.15 mm nominal bore
359	Providing and fixing PTMT bib cock of approved quality and colour. 15mm nominal bore, 86 mm long, weighing not less than 88 gms
360	Providing and fixing PTMT bib cock of approved quality and colour. 15mm nominal bore, 90 mm long. Weighing not less than 93 gms.
361	Providing and fixing PTMT stop cock of approved quality and colour.15 mm nominal bore, 86 mm long, weighing not less than 88 gms.
362	Providing and fixing PTMT stop cock of approved quality and colour. 20mm nominal bore, 89 mm long. Weighing not less than 88 gms.
363	Providing and fixing PTMT pillar cock of approved quality and colour.15 mm nominal bore, 107 mm long, weighing not less than 110 gms.
364	Providing and fixing PTMT, push cock of approved quality and colour. 15 mm nominal bore, 98 mm long, weighing not less than 75 gms.
365	Providing and fixing PTMT grating of approved quality and colour. Circular type.100 mm nominal dia .
366	Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. 15 mm nominal bore, 105 mm long, weighing not less than 138 gms.
367	Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball.25 mm nominal bore, 152 mm long, weighing not less than 440 gms.
368	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall 15 mm nominal outer dia. Pipes.
369	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall 20 mm nominal outer dia. Pipes.
370	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall 25 mm nominal outer dia .Pipes.
371	Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length.
372	Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour. 20 mm nominal bore, weighing not less than 40 gms.
373	Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour. 25mm nominal bore, weighing not less than 62 gms.
374	Regulating necessary controlling valves provided in the water supply pipe line to various sector of residential quarters, service building etc. situated in permanent township including routine maintenance and repairing of external pipe lines &valves of all size by deploying man power as required including necessary T& P etc. all complete as per instruction of EIC. The following man power is to be engaged for day to day work.Fitter -01 No. Helper/Valve man -02 Nos
375	GI Plug 20 mm
376	Jumper Washer
377	Repairing of existing bib cock/ stop cock of differentbuilding including necessary washer,etc as per instruction of EIC
378	GI nipple 15mm
379	GI Plug 25mm
380	Providing and fixing GI Nipple of 25 mm dia.
381	syphon washer for cistern
382	Rectification/ cleaning of chocked internal/G I pipe above 25 mm dia.
383	Rectification/ cleaning of chocked external/G I pipe up to 25 mm dia.
384	GI nipple 20mm
385	Supply of GI socket 15mm
386	Supply of GI socket 20mm
387	GI elbow 15mm
388	GI elbow 20mm
389	Repairing of existing high/low level Cistern including small consumables e.g. washer,nut etc as per instruction of EIC
390	GI Tee 15mm
391	Steel Jali 100 mm
392	Providing and fixing GI Socket of 25 mm dia.
393	Providing and fixing GI Nipple of 40 mm dia.
394	Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour. 20 mm nominal bore, weighing not less than 40 gms
395	Providing and fixing GI Elbow.25 mm dia
396	GI Tee 20mm
397	Bib cock/Pillar cock washer
398	Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour. 25 mm nominal bore, weighing not less than 62 gms
399	Handle and lever for low level cistern
400	Providing and fixing GI Tee of 25mm dai.
401	P/f GI Tee 40 mm
402	C.I. bracket for wash basin and sinks pair .
403	Providing and fixing GI Elbow.40 mm dia
404	Providing and fixing PVC waste pipe for sink and wash basin including PVC waste fitting complete. Flexible pipe 32 mm
405	Providing and fixing PTMT waste coupling for sink and wash basin, of approved quality and colour, waste coupling 31mm dia of 79 mm length and 62 mm breadth weighing not less than 45 gms.
406	Providing and fixing PTMT Waste coupling for wash basin and sink, of approved quality and colour. Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms
407	Providing and fixing reducing socket of 50 mm to smaller size.
408	P/f GI socket 50mm
409	Providing and fixing GI Elbow.50 mm dia
410	Providing and fixing GI Nipple of 50 mm dia.
411	Providing and fixing GI bend of 50 mm dia.
412	Providing C I/G I flange for different dia pipe. 50 mm dia.
413	Providing and fixing rubber packing 5mm thick complete as per instruction of EIC
414	P/f GI flange 50mm
415	Providing C I/G I flange for different dia pipe. 80 mm dia.
416	Providing and fixing nuts, bolts for flange of approved quality as per instruction of EIC
417	syphon for low level cistern
418	Providing and fixing GI Tee of 50 mm dai.
419	P/f GI reducer 80 to 25 mm
420	Providing C I/G I flange for different dia pipe. 100 mm dia.
421	Supply of gland packing for C I Sluice valve 6mm to 20 mm thick of approved quality as per instruction of EIC
422	P/f GI socket 80mm
423	Providing and fixing 15 mm CP brass pillar taps
424	Supplying of grease
425	P/f GI reducer 100 to 25 mm
426	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall 40 mm nominal outer dia. Pipes.
427	Providing C I/G I flange for different dia pipe. 150 mm dia.
428	Providing and fixing GI Tee of 80 mm dai.
429	Supply of bal bearing for repairing of installed pumps in pump house P/T Amlohri DS 6307
430	Supply of S.S Spindle with check nuts suitable for CI Sluice valve.50 mm dia.
431	Supply of bal bearing for repairing of installed pumps in pump house P/T Amlohri DS 6308
432	Supply of bal bearing for repairing of installed pumps in pump house P/T Amlohri DS 6309
433	Supply of S.S Spindle with check nuts suitable for CI Sluice valve.80 mm dia.
434	Supply of S.S Spindle with check nuts suitable for CI Sluice valve.100 mm dia.
435	Supply of S.S Spindle with check nuts suitable for CI Sluice valve.150 mm dia.
436	Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm C.P. brass pillar tap.
437	Providing and fixing CI Sluice valves (with cap) complete with bolts,nuts,rubber insertions etc( the tail piece if required will be paid separately).50 mm diameter class I.
438	Providing and fixing CI Sluice valves (with cap) complete with bolts,nuts,rubber insertions etc( the tail piece if required will be paid separately).80 mm diameter class I.
439	Brick work with FALG bricks of class designation 7.5 in foundation and plinth in Cement mortar 1:6 (1 cement : 6 coarse sand)
440	Providing and fixing C I foot valve 125 mm dia
441	Providing anf fixing brass hand faucet (Tapsteq CP Health faucet Hand Shower)
442	Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge.
443	Laying old cement cocrete interlocking paver blocks of any design/shape laid in required line, level, curvature, colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineerin-charge. (Old CC paver blocks shall be supplied by the department free of cost).
444	Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.
445	Pest/Mosquito Control
446	Anti adult measures: General disinfection/pest control with new generation odourless, colourless insecticides which should be safe for human being and effective for all kind of house hold insects like mosquitos, house flies,etc. using Residential spray of Deltamethrin 2.5% SC flow (K-othrine or approved equivalent) insecticides should be sprayed uniformly over the surfaces of walls, ceilings, etc. Frequency- Once in 3 months
447	Anti Adult Measures-General disinfection/pest control with a new generation odourless ,colourless insecticides which should be safe for human being and effective for all kind of household insects like mosquitos , houseflies etc.Using residual spray of Cyfluthrin 5% EW(Solfac EW OSO or approved equivalent ) . Insecticides should be sprayed uniformly over the surfaces of wall,ceiling,etc.Frequency -once in 3 month
448	Thermal fogging using insecticides deltamethrine 1.25% ULV(King fog or approved equivalent) mixed with diesel in the ratio of 1:199 for outdoor operation of colony, etc.
449	Anti Larvac measures- Treatment by using diflubenzuron 25% WP(Bi-Larv or approved equivalent) solution to be spread as per instruction of EIC. Frequency- Weekly
450	Supply of Bleaching Powder
451	Management Team
452	Facility Manager for heading the entire facility team of Office and Residential Complex and Single point of contact & overall in charge of FM On-site Operations and reporting to engineer-incharge or his representative. (26 days) - One No.
453	Asst. Facility Manager (Technical) for supporting Critical Services Operations & reporting to Facility Manager. (26 days) 02 Nos
454	ELECTRICAL PART – A (Supply)
455	Supply of 6 pin, 15/16 & 5/6 amp socket outlet, piano type, ISI marked.
456	Supply of switch socket combined of approved make & ISI marked, fush type, 20/15 Amp 3/6 Pin 250 V
457	Supply of SP 15/16 Amps, one way switch, piano type, ISI marked.
458	Supply of 3/5 pin, 5/6 amp socket outlet, piano type, ISI marked.
459	Supply of SP 5/6 Amps, one way switch, piano type, ISI marked .
460	Supply of PVC casing capping 3/4” (20mm x 12mm) ISI Marked.
461	Supply of PVC casing capping 1\\" (25mmx 12mm) ISI Marked.
462	Supply of Bell Push,Piono type
463	Supplying & fixing of 4x4 PVC Plain Board
464	Supplying & fixing of 7x4 PVC Plain Board
465	Supplying & fixing of 8x6 PVC Plain Board
466	Supplying & fixing of 8x10 PVC Plain Board
467	Supply of 3 mm thick phenolic laminated sheet
468	Supply of Iron Screw 40mm x 6mm/35mm x 6mm
469	Supply of Piano type Non Modular domestic fan Regulator Ceiling fan 1200mm 220/250 Volt, Item Code- 4600016857
470	Supplying of ISI Maerked and accepted standard of Miniature Circuit Breaker (MCB) “C” series suitable for 240/415 volts,50 cycle,10ka Value AC supply confirming to IS:8828:1996,IEC :60898:2002 but without enclosures. For Triple Pole &Neutral (TPN), 50Amp to 63 Amp Rating.
471	Supply of ISI Marked and approved make of Moulded Case Circuit Breaker (MCCB) suitable for 3Phase, 3Pole, 50Hz,415 Volts, AC supply with respective interrupting capacity (KA) at 415 Volts cited against their range standard conforming to IS-8828 MCCB with Breaking Capacity 25 KA at 415volt, current Rating-125 Amps & 80%-100% adjustable
472	Supplying of ISI Marked and approved make of Moulded Case Circuit Breaker (MCCB) suitable for 3Phase,3Pole,50Hz,415 Volts,AC supply with respective interrupting capacity (KA) at 415 Volts cited against their range standard confirming to IS-8828 MCCB with Breaking Capacity 35 ka at 415 volts, Current Rating-200 Amps & adjustable 80%-100%
473	Supplying of ISI Marked and approved make of Moulded Case Circuit Breaker (MCCB) suitable for 3Phase,3Pole,50Hz,415 Volts,AC supply with respective interrupting capacity (KA) at 415 Volts cited against their range standard confirming to IS-8828 MCCB with Breaking Capacity 35 ka 4at 415 volts, Current Rating- 400 Amps & adjustable 80%-100%
474	Supply of Switch Fuse unit (Rewirable type) Two pole, 240 Volt, 32 Amps ISI Marked
475	Supply of TPN 63 Amp, MCB, AC, Breaking capacity-36 KA at 415 volt
476	Supply of Switch-Disconnector (Isolator) 100 Amps double pole, Standard make ,230 volt
477	Supply of Condensar,2.5 mfd,230 Volts AC (Item Code 4600016871)
478	Supply of PVC insulation tape, size- 19mm x 10 mtr (Item code 4600017914)
479	Supply of Angle Bulb Holder
480	Supply of Plug top, 16 Amp 250 volt , 3-pin type ISI Marked
481	Supply of ISI marked FRLS PVC insulated single core, copper wire,1.5 Sqmm, single core cable
482	Supply of ISI marked FRLS PVC insulated single core, copper wire,2.5 Sqmm, single core cable
483	Supply of ISI marked FRLS PVC insulated single core, copper wire,4 Sqmm, single core cable
484	Supply of ISI marked FRLS PVC insulated single core, copper wire,6 Sqmm, single core cable
485	Supply of MS nut and bolts 16mm x 75mm w/nut, Item code -4600027877
486	Supply of Stay insulator 11KV grade Item code 4600019075
487	Supply of GI earth/stay wire,7/10- SWG Item code 4600019128
488	ELECTRICAL PART –B
489	Removing and fixing of electrical consumable items in residential quarters, service buildings (MQ- 320, NMQ-672, B-type-216, NB – type-78, C –type-68,D,type-16, GM Banglow, Gm office, Officers Club ,HI-Tech Guest House, Workers Club Kalyanmandap, Junior Rest House, Telephone Exchange, School ,CISF Barrack etc.) by engaging 04 (Four) manpower consisting of 02 skilled (Electrician) & 02 Unskilled (Helper) per day for 730 days to attend the daily complaints of above mentioned location.
490	Attending no power of residential quarters and service buildings, service connection, jumpering of LT O/H line & HT O/H line (6.6 KV) including changing of pin , shackle insulators and power cable connection of sector sub-station by engaging 04 (Four) manpower consisting of 02 skilled (Electrician) & 02 unskilled (Helper) per day for 730 days.
491	Annual maintenance of street lighting of township including feeder road from Nawanagar to CISF control room (Old GM office), CISF unit line and Weigh Bridge premises of sand plant at Amlohri Project by engaging 04 (Four) manpower consisting of 02 skilled (Electrician) & 02 unskilled (Helper) per day for 02 years.
492	Repair and maintenance of window/split air conditioners , water coolers and refrigerators installed at different establishment of Amlohri Project by engaging 02 AC technician (Skilled) and 01 Helper (unskilled) per day for two years from March to October every year.(Excluding Sunday)
493	Repair and maintenance of Geyser, refrigerators installed at different establishment of Amlohri Project by engaging 01 technician (Skilled) per day for two years from January to February every year. (Excluding Sunday)
494	ELECTRICAL PART – C (Material and Labour)
495	Erection of Rs joist pole/H beam/steel tubular pole/steel rail pole of length exceeding 10mtrs but not exceeding 13mtrs in cement concrete M-10(1 cement:3 core sand:6 graded stone aggregate 40 mm nominal size) base foundation, muffing including excavation and back refilling etc as required.
496	Supplying and erection of stay set complete with 16 mm dia, 1.8mtr long stay rod, turn buckle anchor plate of size 200x200mmx6mm thimble , stay clamp, bow tightner,7/3.15dia GI stay wire etc in cement concrete M-10 (1cement:3 core sand:6 graded stone aggregate 40mm nominal size foundation, including excavation and back refilling etc as required.
497	Erection of all aluminium conductor of 7/3.4.00 mm to 7/4.0 mm dia and above including binding etc as required.
498	Supplying and erection of 75mm x 90mm shackle insulator with G.I. bolts, nuts and straps etc as required.
499	Supplying and erection of 11KV (5 KN) polymer pin insulator complete with long steel head G.I. pin, nut washer etc as required
500	Supplying and erection of 11kv (45 KN) polymer disc insulator for 11 kv/6.6kv overhead lines with galvanizes insulator fiting, ball and socket type, and complete with galvanized strain clamp bolts, nuts, washers etc as required.

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents

Also Visit

Tenders

Madhya Pradesh Tenders

Services Tenders

Hospitality Related Services Tenders

Facility Management Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Routine Operation, Maintenance And Providing Civil & Electrical Maintenance (Including Facility Management Services) For Office And/Or Residential Complex At Amlohri Project (For The Period Of 2 Years)., Singrauli-Madhya Pradesh

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Routine Operation, Maintenance And Providing Civil & Electrical Maintenance (Including Facility Management Services) For Office And/Or Residential Complex At Amlohri Project (For The Period Of 2 Years)., Singrauli-Madhya Pradesh

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us