|
| 1 | Labour for site clearance |
| 2 | Dismantling old plaster and pointing in cement or lime and raking out joints to 15mm depth, watering and disposal of unserviceable materials with all leads all complete as per direction of E/I. |
| 3 | Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. |
| 4 | Providing 6mm cement plaster (1:4) in celling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. B.C.D 5.7.6 |
| 5 | whitewash two coat over old surface all complete as per building specification and direction of E/I |
| 6 | Providing two coat of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I. B.C.D 5.8.45 |
| 7 | Providing two coats of painting with ready mixed paint of approved shade and make over old wooden surface including cleaning the surface after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I. |
| 8 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 9 | Dismantling pucca brick or lime work including stacking serviceable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I. |
| 10 | Providing designation 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9\\"x4.5\\"x3\\") in C.M. (1:6) in foundation and plinth with approved uality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 11 | Supplying fitting and fixing M.S grill made of 20x60mm M.S. flat as per approved design and drawing properly fabricated with joints continuous fillet welded and finished smooth carriage of grill to work site hoisting as per building specification and direction of E/I 5.5.12 |
| 12 | sand lead 20km (p) |
| 13 | brick lead 5km (p) |
| 14 | cement lead 3 km (p) |
| 15 | Wiring for light/point/Exhaust fan point/call bell point with 1.5 sq.mm FRPVC insulated copper conductor cable in surface/recessed PVC conducit as required. With piano type switch phenolic laminated sheet MS Box earthing the point PVC insulated copper 1.5 Sq.mm FR PVC insulated copper conductor single core cable etc. at required. |
| 16 | Wiring for circuit/sub main wiring along with earth wire with the following sizes of PVC insulated copper conductor single core cable in surface/racessed PVC conduit as required. 1.7.2 :- 2x2.5 sqmm+1x2.5sqmm earth wire |
| 17 | 1.7.5 :- 2x10 sqmm+1x10 sqmm earth wire |
| 18 | 1.7.12 :- 4x16 sqmm+2x6 sqmm earth wire |
| 19 | Supplying and fixing suitable size GI box/PVC all complete job 1.22.9 :- 210x206x48mm |
| 20 | 1.22.8 :- 170x221x48mm |
| 21 | 1.22.1 :- 75x75x50mm |
| 22 | Supplying and fixing of following way single pole & neutral, sheet steel, MCB distribution board 240 volts, on surface /recess, complete with tinned copper bushbars ,neutral busbar, earth bar , din bar ,detachable gland plate , interconnections ,phosphatized and powder painted including earthing etc. as requried. (but without MCB/RCCB/ISOLATOR) |
| 23 | Supplying and Fixing- C series MCB 6/32/Amps TPN All complete job |
| 24 | Supplying and Fixing- C series MCB 6/32/Amps SPN All complete job |
| 25 | Supplying and fixing following rating four pole 415 volts Isolator in the existing MCB DB complete with connections testing and commissioning etc as required 2.15.2 :- 63 amps |
| 26 | ITC ceiling fan installation |
| 27 | ITC exhaust fan upto 450mm sweep installation |
| 28 | Supplying Installation ,testing and commissioning of following size ceing fan 3 blades conforming to IS : 374:2019 including wiring the down rods of standard length ( upto 30 cm ) with 1.5 sq. mm FR PVC insulated ,copper wire suitable for 230 V 50 Hz, single phase supply etc. complete as required. 1200 mm (48'') Ceiling fan |
| 29 | Supplying 300 mm exhust Fan 12'' (300 mm) |
| 30 | Supplying LED 15/16 Watt |
| 31 | S/F Batten Holder -Do - -do- |
| 32 | supplying and fixing following piano type switch/socket on the exiting box/ cover including connections etc as required 3 pin 5/6 A socket outlet Each |
| 33 | 5/6 amps switch |
| 34 | Supplying fitting and fixing viterous shite glazed earthen ware I.W.C. of parry hindustan or any other I.S.S approved make with 100 mm H.C.I. \\"p\\" trap 15 litres C.I.. Or C. pull and let go flushing clstern of name or other I.S.S equivalent make, complete with all fitting,C.i.. or C.C brackets 32 mm alkathene/P.V.C telescopoc flush,pipe about 2 M long with one brass coupling and clamps G.I chain pull including supplying and fixing a pair of viterous white glazed earthenware where footrest to be fixed in floor 15 mm C.I body brass spindle stop cock of weigth not less than 50 grms. 15mm P.V.C connection pipe 450 mm long and the exposed pipe amd cistern with two coats of approved paint over a coat of red oxide primer etc all complete as per specification and direction of E/I. (C) 450 mm long I.W.C (b)with 12.5lit. low level C.I cistern |
| 35 | Providing fitting and fixing vitreous white glazed earthen ware Wash hand basinof parry hindustan or any other I.S.S approved make supported on painted C.I or R.S brackets with 32mm C.I,15mm dia C.I body brass spindle stop cock of approved quality of weight not less than ,350 grams ,32 mm PVC waste pipe 750mm long with brass coupling at one end and making plumber joints etc.all complete as per specification and direction of E/I. |
| 36 | Providing and fixing male ended 15 mm dia brass bib cock of approved quality (wt. not less than 350 gms) with extra socket all complete as per specification and direction of E/I. |
| 37 | Supplying fitting and fixing (b) mirror of 6mm thick glass bevelled edge mirror including C.P brass revolving fitting 3mm ply wood board and C.P hinges to fix with mirror. Complete with all materials as per specification and direction of E/I. (i) 600mm x450mm size |
| 38 | (C) (i)C. P brass towel rail 20mm x 600mm with bracket container |
| 39 | Making Holes in wall for laying GI Pipes & Restoring the same after pipe laying as per specification (250 mm Thick Wall) |
| 40 | Providing & Fixing Brass /CI Stop Cork Of approved quality (A) 20 mm Dia |
| 41 | Providing and fixing CPVC pipes do……..do…… all complete job. Exposed on Wall20 mm nominal outer dia Pipes |
| 42 | 32 mm nominal outer dia Pipes |
| 43 | Conselled 15mm dia |
| 44 | Supplying 100mm dia submersible pump sets confirming to IS 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless pump shaft and polypropylene/ noryl impeller. Motor suitable for working on 415V+10%, 3HP, 5o Hz, A.C. supply with cable guard, thrust carbon / fiber bearing to withstand entire hydraulic thrust, water proof winding shall be provided. The pump set shall be suitabl for direct coupling. Pump shall have suitable outlet as per manufacturers design. Anti thrust stream lined nonreturn valve shall be provided with pump. 3 meter submersible copper conductor cable in single / double run shall be provided with each pump.Submersible pump Set of 2 HP Single Phase 150 mm dia (with Bronze impeller) up to 8 stages. |
| 45 | D.O.L. Starter |
| 46 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittingswith one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 40mm nominal outer dia pipe |
| 47 | Rope and motor lowering and fitting |
| 48 | Polythene water storage tank of mark with cover and suitable lcocking system in double layer confirming to Is 12701-1996 with ;atest revision |
| 49 | Goods & Service Tax (G.S.T. 18%) |
| 50 | 1% Labour Cess Please Enable Macros to View BoQ information |
