|
| 1 | Cleaning of exposed concrete surface of sticking material including loose and foreign material by sand blasting with fine sand followed by and including cleaning with oil free air blast as required and as per direction of the Engineer-in-charge. |
| 2 | Dismantling old plaster or pointing, raking out joints, cleaning and preparing the surface for replastering or re-pointing including disposal of rubbish to the dumping ground with all leads and lifts etc.complete as per direction of the Engineer- incharge. |
| 3 | Dismantling GS sheet roofing including ridges, hips, valleys, gutters wind ties etc. including dismembering and stacking of serviceable materials and unserviceable materials separately with all lifts and upto a lead of 50 m etc.complete as perdirection of the Engineer- in-charge. |
| 4 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.-All kinds of soil |
| 5 | Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete. |
| 6 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering --All work upto plinth level:i) 1:2:4 ( 1 Cement: 2 fine sand :4 graded well burnt brick aggregate 20 mm nominal size) |
| 7 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement- -All work upto plinth level: 1:2:4 ( 1 Cement: 2 fine sand : 4 graded well burnt brick aggregate 20 mm nominal size) |
| 8 | Centering shuttering including struttings, propping etc. and removal of form work for:i) Suspended floors, roofs, landings, balconies and access platform with 12 mm thick shuttering ply |
| 9 | ii) Lintels, beams, plinth beams, girders, bressumers and cantilevers with wooden plank |
| 10 | iii) Columns, Pillars, Piers, Abutments, Posts and Struts with wooden plank |
| 11 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and skirting courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement- i)In plinth and skirting courses, fillets, columns, pillars,posts and strutsa)1:2:4 ( 1 Cement: 2 fine sand : 4 graded well burnt brick aggregate 20 mm nominal size) |
| 12 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement-i) RCC work in beams, lintels, bands, plain window sills, staircases and spiral staircases excluding precast spiral staircase. a) 1:2:4 ( 1 Cement: 2 fine sand : 4 graded well burnt brick aggregate 20 mm nominal size) |
| 13 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. i)Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 14 | Reinforcement for R.C.C. work including straightening,cutting, bending, placing in position and binding allcomplete above plinth level.i) Thermo-Mechanically Treated bars of grade Fe-500D ormore |
| 15 | First class brick work in foundation and plinth including cost of all materials as required complete:- In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 16 | First class brick work in superstructure above plinth level & upto floor-five level including cost of all materials as required complete:- i) In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 17 | Half brick masonry work with first class bricks in foundation and plinth including cost of all materials as required complete:- i) In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 18 | Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete:- i)In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 19 | 12 mm cement plaster of mix Cement mortar 1:4 (1 cement : 4 fine sand) |
| 20 | Neat cement punning. |
| 21 | Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge.i) 50mm average thickness |
| 22 | Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 fine sand with polymer minimum 2%by wt. of cement used) as per specifications and as per direction of the Engineer-in-charge.Note: Measurement and payment: The pre-measurement of thickness shall be done just after the surfacepreparation is completed and Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated bysounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 N/ mm2)i) 25 mm average thickness in 2 layers. |
| 23 | Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound, as directed by Engineer-in-Charge and consisting of applying :(a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofingcement compound @ 0.253 kg/sqm.(b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm.(c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and fine sand @1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entiretreatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around.(d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured. |
| 24 | Grading roof for water proofing treatment complete as required as per direction of the Engineer-in-charge with :i) Cement concrete 1:2:4 (1 cement : 2 fine sand : 4 graded stone aggregate 20 mm nominal size) |
| 25 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position :(i) Local Teak wood |
| 26 | Providing wood work in frames of false ceiling, partitions etc. sawn and put up in position :(i) Local Teak wood |
| 27 | Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete :i) Gamair Wooda) 50×12 mm |
| 28 | Providing and fixing plain Multipurpose Cement board(High Pressure steam cured) as per IS : 14862 : 2000 with suitable screws for fibre cement board inceiling etc. complete as per direction of Engineer-incharge.(frame work to be paid separately) :i) 6 mm thick cement board |
| 29 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1stclass hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands andface veeners on both faces of shutters.(i) 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. |
| 30 | Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete : i) 25 mm dia. |
| 31 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete. i) Fixed to openings /wooden frames with rawl plugs screws etc. |
| 32 | Providing and fixing factory made P.V.C. door frame of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet mitred at corners and joined with 2 Nos. of 150mm long brackets of 15x15mm M.S. square tube, the vertical door profiles to be reinforced with 19×19mm MSsquare tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame . The door frame to be fixed to the wall usuing MS screws of65/100 mm size complete as per manufacturers' specification and direction of Engineer-In-Charge. |
| 33 | Providing and fixing 28 mm thick door shutter made of solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 71mm width & 28mm thick as vertical & horizontal styles. Joints are made using solvent adhesive and GI ‘C sections (39mm x 19mm x 0.6mm thick) or M S pipe (40mm x 20mm ) stiffener frame insert & telescopic polymeric ‘L’ corners .The panel shall be filled with 3mm thick high - pressure compact laminate as per manufacturer’s specifications and directions of the Engineer-incharge, cover moulding shall be provided for covering fixing screws and elegant look.( for W.C.bathroom door shutter). |
| 34 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawing and the direction of Engineerincharge. (Glazing and paneling and dash fasteners to be paid for separately) :i) For fixed portion of approved quantitya) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). |
| 35 | For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing fittings wherever required including the cost of EPDM rubber / neoprene gasket required ( Fittings shall be paid for separately ):i) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). |
| 36 | Providing and fixing glazing of approved quality in aluminium doors, windows, ventilator, shutters and partition etc. with EPDM rubber / neoprene gasket etc. complete as per architectural drawing and the direction of Engineer-in-charge (Cost of snap beading shall be paid in basic item) :i) With glass/ float glass panes of 4.0 m thickness ( weight not less than 10.0 kg / sqm ) |
| 37 | Providing 40 × 5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30 × 10 × 15 cm 1:3:6 mix (1 cement:3 fine sand:6 graded stone aggregate 20mm nominal size) |
| 38 | Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :i) 300x16 mm |
| 39 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than gradeAC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete i)300x10 mm |
| 40 | Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :i) 125 mm |
| 41 | Providing and fixing hard drawn steel wire fabric 75 x 25 mm mesh of weight not less than 7.75 Kg per sqm to window frames etc. including 62 x 19 mm beading of Gamair wood. |
| 42 | Supply & installation of pre-painted Galvalume sheets for roofing/cladding (size, shape and pitch of corrugation as approved by Engineer-in-charge) in 550mpa steel grade, made out of Cold Rolled Steelcoated with Zinc-Aluminium alloy coating of 43.5% Zn, 55% Al and 1.5% Silicon confirming to ASTMA792/A792M and AS1397, Alloy coating AZ150/AZ70, colour coated with high quality Polyester coating, top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-incharge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM washers filled with white lead complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses andincluding cutting to size and shape wherever required.i) 0.50mm thickness |
| 43 | Supply & installation of pre-painted Galvalume sheets roofing accessories in 550mpa steel steel grade, made out of Cold rolled steel coated with Zinc-Aluminium alloy coating of 43.5% Zn, 55% Al and 1.5% Silicon confirming to AASTM A792/A792M and AS1397, Alloycoating AZ150/AZ70, colour coated with high quality polyester coating, top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation. The sheetshall be fixed using self drilling /self tapping screws with EPDM washers complete for Ridges/Valley/Gutter/Flashing of width 610mm:i) 0.50mm thickness |
| 44 | Providing corrugated G.S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. (i)0.50 mm thick with zinc coating not less than 275gm/m2 |
| 45 | Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete.i) 0.63mm thick with zinc coating not less than 275gm/m2 |
| 46 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of specialsections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed tothe ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall befixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsumboard to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish oftapered and square edges of the board with recommended jointing compound of joint and two coats of primer su,i tjoabinletinfogr tbapoaersd ,, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills,diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings,specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge gypsum board conforming toIS: 2095- Part I. |
| 47 | Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well ascurvilinear portions of the building , for all heights and all levels etc. including:(a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it water tight including checking of all the structural and functionaldesign.(b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of aluminium composite panel material of approved thickness and specification. The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF /Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.(c) The fastening brackets of Aluminium alloy 6005 T5 / MSwith Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316,Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architecturaldrawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual areaon the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.\\"Aluminium Composite Panels of 3mm total thickness with Top coil – 0.25mm AA3003 Grade manufactured as per IS-737 1986, FR Grade Class B1 with 2.50mm Mineral Core with minimum 70-72% Inorganic content (AluminiumHydroxide and Magnesium Hydroxide) 28-30% Organiccontent (LDPE) conforming to ASTM E-119-16,18 and EN 13501 - 1 class B1 and Bottom coil – 0.50mm AA3003 Grade manufactured as per IS-737 1986 with minimum 25microns lead free PVDF Coating conforming to AAMA2605 on top coil and Service coating on Back Coil (4 - 6 microns) having minimum panel weight of 5.25 Kg/m2 |
| 48 | Providing and fixing precast chequered cement concrete tiles 22 mm thick, laid in footpath & courtyard, on 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning complete as per direction of the eng-in-charge.1. In dark shade using ordinary cement |
| 49 | Providing and fixing 1st class quality ceramic glazed wall tiles conforming to IS : 15622 - 2017 (thickness to be specified by the manufacturer) of approved make in all colours, shades of any size as approved by Engineer-inchargein skirting, risers of steps and dados, laid over 12mm thick bed of cement mortar 1 : 3 (1 cement : 3 finesand) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade etc. all complete as per direction of the Engineer in-charge.i) 450 mm X 300 mm in all shades and design |
| 50 | ii) 600 mm X 300 mm in all shades and design |
| 51 | Providing and laying 1st class quality ceramic floor tiles in different sizes (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 -2017 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid over 20 mm thick cement mortar 1:4 (1 cement : 4 fine sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc. all complete as per direction of the Engineer in-charge.i) Mat Finish Tiles/ Anti-skid Tiles/ Glossy Tilesa) 600 mm x 600 mm in all shades and designs 1st class quality ceramic floor Porcelain tiles |
| 52 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 - 2017, of approved make, in all colours and shades, laid over 20mm thick cement mortar 1:4 (1 cement : 4 fine sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.i) Double charged Stainfree vitrified tiles (Glossy)a)Size of tile 600 mm x 600 mm |
| 53 | ii) Glazed Vitrified Tiles - Full Body (Glossy / Mat Finish/Anti-Skid)a) Size of tile 600 mm x 600 mm |
| 54 | Providing and laying factory made coloured chamfered edge Cement Concrete paver blocks of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. complete as per specifications & approval/ direction of Engineer-in-Charge.i) 80 mm thick factory made c.c.interlocking paver block of M-30 Grade. |
| 55 | Providing and fixing gang saw cut of approved thickness mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base of cement mortar 1:4 ( 1 cement : 4 fine sand ) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing , curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels:-i) 18 mm thick Rajnagar Plain white marble/ Udaipur green marble/ Zebra black marble or equivalent duly approved:-a) Area of slab over 0.50 sqm. |
| 56 | ii) 18 mm thick Granite of any colour and shade duly approved:-a) Area of slab over 0.50 sqm. |
| 57 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer]: i) Two or more coats on new work over an under coat of suitable shade with ordinary paint (primer) of approved brand and manufacture. |
| 58 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 59 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. |
| 60 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 grams/ litre, of approved brand and manufacture to give an even shade[Payment shall be made after submission of Test Certificate issued by the Manufacturer] :New work ( two or more coats) over and including water thinnable priming coat with cement primer. |
| 61 | Distempering with 1st quality washable acrylic distemper of approved brand and manufacture and of required shade on old work ( one or more coats ), to give an even shade as required complete as perdirection of the Engineer in charge. |
| 62 | Distempering with Superior quality interior paint of approved brand and manufacture to give an even shade.New work ( two or more coats) over and including water thinnable priming coat with cement primer. |
| 63 | Finishing walls with acrylic smooth exterior paint of required shade of approved brand and manufacture [Payment shall be made after submission of Test Certificate issued by the Manufacturer] :New work ( two or more coats applied @ 1.67 litre/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 64 | Finishing walls with acrylic smooth exterior paint of required shade of approved brand and manufacture on old work ( one or more coats ) including preparation of surface as required complete as per direction of the Engineer in charge. |
| 65 | Finishing walls with Superior quality exterior paint of required shade of approved brand and manufacture for VIP quarters.New work ( two or more coats applied @ 1.67 litre/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 66 | Painting with synthetic enamel paint ( one or more coats ) of required colour of approved brand and manufacture on old work to give an even shade including preparation of surface as required complete as per direction of the Engineer in charge. |
| 67 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :i) White Vitreous china Orrisa pattern W.C. pan of size 580x440 mm with integral type foot rests. |
| 68 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :i) W.C. pan with ISI marked white solid plastic seat and lid. |
| 69 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.i) 10 litre capacity-White |
| 70 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :i) White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps |
| 71 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. |
| 72 | Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the wallswherever required:i) Kitchen sink without drain boarda) 610x460 mm bowl depth 200 mm. |
| 73 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour.i) 600mm long towel rail with total length of 645mm, width 78mm and effective height of 88mm, weighing not less than 190gms. |
| 74 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipei) 40 mm dia |
| 75 | Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 76 | Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 77 | Providing and fixing ball valve (brass) of approved quality High or low pressure, with plastic floats complete :i) 15 mm nominal bore |
| 78 | ii) 20 mm nominal bore |
| 79 | iii) 25 mm nominal bore |
| 80 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931i) 15 mm nominal bore |
| 81 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 82 | Labour charges for washing GI pipe internal for removing iron deposited iron etc. in/c replacement of the pipe from original position as per direction of the Engineer-in-charge |
| 83 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing ofpipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on walli) 15 mm nominal outer dia .Pipes. |
| 84 | ii) 20 mm nominal outer dia .Pipes. |
| 85 | iii) 25 mm nominal outer dia .Pipes. |
| 86 | iv) 40 mm nominal outer dia .Pipes. |
| 87 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. External work i) 15 mm nominal outer dia .Pipes. |
| 88 | ii) 20 mm nominal outer dia .Pipes. |
| 89 | iii) 25 mm nominal outer dia .Pipes. |
| 90 | iv) 32 mm nominal outer dia .Pipes. |
| 91 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making longscrews etc. complete as per CPWD specification and direction of the Engineer - in - charge.(New work)i) 15 mm nominal bore |
| 92 | (ii) 20 mm nominal bore |
| 93 | (iii) 25 mm nominal bore |
| 94 | Providing and fixing PTMT pillar cock of approved quality and colour i) 15mm nominal bore, 125mm long foam flow, Weighing not less than 120 gms. |
| 95 | Providing and fixing brass stop cock of approvedquality :i) 20 mm nominal bore |
| 96 | Providing and fixing uplasticised PVC connection pipe with brass unions :i) 45 cm lengtha) 20 mm nominal bore |
| 97 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes (working pressure 4 kg/cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion:i) Single socketed pipe - 75 mm OD |
| 98 | (ii) Single socketed pipe - 110 mm OD |
| 99 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing with cement mortar 1 : 4 (1cement : 4 fine sand) making good the wall etc. complete.(a) 75mm |
| 100 | (b) 110 mm |
| 101 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water, soil, waste & vent pipes pipesconforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion:(A)Coupler(i) 75mm |
| 102 | (ii) 110 mm |
| 103 | (B) Single equal tee with door(i) 75x75x75 mm |
| 104 | (ii) 110x110x110 mm |
| 105 | (C) Bend 87.5°(i) 75mm |
| 106 | (ii) 110 mm |
| 107 | Labour charge for cleaning inspection chamber with night soil & refusal water as per direction of Engineer-in-Charge. |
| 108 | Renewing glass panes with putty and nails wherever necessary, including racking out the old putty:1. Float Glass panes of 4 mm . |
| 109 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.i) Hot finished welded type tubes |
| 110 | Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. complete as required:-i) (i)In grating, frames, guard bar, railing, brackets, gates and similar works, all complete. |
| 111 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and makingcurvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., ofrequired size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight ofstainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 112 | Shifting of existing office almirahs (in/c packed official documents, files etc) or other official materials from one place to another place for mtc. Of a room & placing the same in the same position after mtc. Properly without any demage as per direction of the Engineer-in-charge. |
| 113 | Providing & fixing 2-in-1 CP bib cock of JAQUAR/PARRYWARE/ROYAL/HINDWARE as selected & approved at VVIP qtr as per direction of the Engineer-In-Charge. |
| 114 | Providing & fixing white vitreous china european type low level WC pan of JAQUAR/PARRYWARE/HINDWARE with seat & lid in/c white vitreous china flushing cistern (as selected & approved) with manually controlled device with all fittings & fixtures complete in/c cutting & making good the walls & floors wherever required as per direction of the Eng-In-Charge. |
| 115 | Providing & fixing white vitreous china wash basin of HINDWARE/PARRYWARE/JAQUAR (as selected & approved) with long pedestal,C.I.brackets,32mm CP brass waste of standard pattern in/c painting of fittings & brackets, cutting &making good the walls & floors wherever required as per direction of the Eng-In-Charge.White Vitreous China wash basin size. |
| 116 | Providing & fixing Cardiff health foucet of JAQUAR/PARRYWARE/ROYAL/HINDWARE as selected & approved with connecting hose as per direction of the Eng-In-Charge. |
| 117 | Providing and fixing GODREJ SILVER STEEL hydraulic door closer with double speed adjustment with necessary accessories and screws etc. complete.as selected & approved as per direction of the E-In-C |
| 118 | Providing & fixing false ceiling with SPUF142-D-01 (different design 10mm thick 150mm width & necessary length) of approved colour concealed type carrier T section (DWUF:406:40*63.5mm) & L section (DWUF:405:40*48) with necessary screw, holdfast PVC beading & MS black pipe structure 48mm dia at 1200mm centre to centre in/c cutting holes & making good the walls complete as per direction of the Eng-In-Charge. |
| 119 | Providing and fixing superior quality Soap dish holder of approved design and colour. .(Jaquar make- code-AKP-35731P). |
| 120 | Providing and fixing superior quality towel rail complete with brackets fixed to wooden cleats with C.P. brass screws with all fittings complete as per direction of the Engineer-in-charge.A. Towel rail 600 mm long .(Jaquar make- code-AKP-35711PS). |
| 121 | Providing and fixing superior quality angular stop cock of approved brand with wall flange. (Jaquar make- code-FON-40053) |
| 122 | Providing and fixing superior quality Bib cock of approved brand with wall flange. (Jaquar make- code-FON-40037) |
| 123 | Providing and fixing superior quality glass shelf 600 mm long complete with brackets fixed to wooden cleats with C.P. brass screws with all fittings complete as per direction of the Engineer-in-charge.A. Glass shelf 600 mm long .(Jaquar make- code-AKP-35771P). |
| 124 | Providing and fixing whole muli bamboo machan, each bamboo tied with coir rope at 150 mm centre to centre, with one layer of champakampa tarja matting complete over a suitable structure properly tied with coir rope asper specification. |
| 125 | Providing, fitting and fixing shelf Reck with Greenply 19mm thick solid boil board, 1mm thick laminated decorative sheet fixed with marine board, fevicol, Muskin tap etc. complete as per direction of Engineer-in-charge. |
| 126 | Wiring for light / fan / exhaust fan / call bell point with 2 x1.5 sq. mm pvc insulated Copper conductor cable (FR) in pvc casing and capping complete with 6/10 amps modular type switch, cover plate, surface modular switch board including connection etc as required:-a) Short Point :- |
| 127 | b) Medium Point :- |
| 128 | c) Long Point :- |
| 129 | Providing and fixing of 3/6 pin 16/20 amps plug point with modular type 16/20 amps switch and socket including connection with 2x2.5 sq. mm PVC insulated Copper conductor cable(FR) on surface modular switch board, earthing the 3rd pin etc. as required:- |
| 130 | Wiring for circuit /Sub-main with following sizes PVC insulated copper conductor cable (FR) in PVC casing and capping etc. as required.a) 2 X 1.5 sq mm |
| 131 | b) 2 X 2.5 sq mm |
| 132 | c) 2 X 4 sq mm |
| 133 | Supplying and fixing of the following electrical accessories including necessary connection etc. as required.A) Electronic 5 step fan regulator |
| 134 | Supplying and fixing of the following sizes PVC switch boards with cover etc. as required.a) 152mm x 203mm (6\\" X 8\\") :- |
| 135 | b) 203mm x 254mm (8\\" X 10\\") :- |
| 136 | Supplying and fixing of the following sizes modular type cover plates for GI/plastic modular switch boards etc. as required.a) 6 module :- |
| 137 | b) 12 module :- |
| 138 | Supplying & fixing of 1400 mm sweep white color AC ceiling fan capacitor type double ball bearing complete with 300 mm down rod,canopies,shackles, 3nos blades, including wiring the down rod with 2x1.5 sqmm PVC insulated Copper conductor cable(FR) (ISI marked) : - |
| 139 | Supplying & installation of 225/230 mm sweep metalic body exhaust fan including connection etc as required:- |
| 140 | b) Recessed/Surface mounted 1ft x 1fSupplying and fixing of following surface/recess mounted LED luminaries in powder coated die cast housing complete with high efficiency polycarbonate diffuser and necessary connection etc. as required (with 50000 burning hours and minimum lumen output of 100 lm/watt):-t decorative 16/18 watt LED panel light with integral driver and high quality polycarbonate diffuser:- |
| 141 | Supplying and fixing of following LED Tubes, retrofit bulbs/lamps for LED luminaries including necessary connection etc. as required:-a) 18/20 watt LED tube with integral driver and polycarbonate diffuser (50000 burning hours and minimum lumen output of 100lm/watt):- |
| 142 | Supplying and installation of powder coated steel sheet enclosure (MCB DB) suitable for 240/415 volts MCB/Isolator/RCCB (SP/SPN/DP/TP/TPN/FP) complete with necessary bus bar, neutral link, din rail, earth bar etc i/c connection as required.A) (2+6) / 8 way SPN MCB DB (double door):- Please Enable Macros to View BoQ information |
