|
| 1 | 2.8.1- Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides andramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. |
| 2 | 2.25- Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift. |
| 3 | A.R D.S.R.2023(1.1.2+2.8.1)-Construction of embankment with approved material abtained from borroe pits cum ( including cost of compensation for earth taken from private land ) with a lift upto 1.5m , transporting to site , spreading, grading to required slope and compacting to meet requirement of table 300.1 and 300.2 as per Technical specification Clause 301.5 AOR for above item 1 Km @ 217.55 Rs., 2.8.1 @ 260.30 = Rs. 477.85 |
| 4 | 16.78.1-Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineerin-Charge. With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30 |
| 5 | 4.1.8- Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-Ill) derived from natural sources: 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 6 | 5.1.2-Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing andreinforcement -All work up to plinth level :1:1.5:3 (1 cement: 1.5 coarse sand (zone-Ill) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 7 | 5.22.6-Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 8 | 5.9- Centering and shuttering including strutting, propping etc. and removal of form for 5.9.1-Foundations, footings, bases of columns, etc. for mass concrete |
| 9 | 5.9.6-Columns, Pillars, Piers, Abutments, Posts and Struts |
| 10 | 5.9.5- Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 11 | 5.9.3- Suspended Floors, Roofs, Landings, Balconies and access platform |
| 12 | 6.1.2- Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement: 6 coarse sand |
| 13 | 6.4.2-Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 14 | 11.2-Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with Jamuna sand, with common burnt clay non modular bricks. |
| 15 | 10.2-Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 16 | 12.1.3-Providing corrugated G.S. sheet roofing including vertical/ curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63 mm thick with zinc coating not less than 275 gm/ m2 |
| 17 | 2.27- Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 18 | 11.26.1- Kata stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade +C37of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement: 4 coarse sand) 25 mm thick |
| 19 | 7.6- 12 MM thick plaster of mix (1:6) |
| 20 | 13.39.1- WHITE WASH Colour washing such as green, blue or buff to give an even shade : New work (two or more coats) with a base coat of white washing with lime |
| 21 | 4.10- Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement: 2 coarse sand (zone-Ill) derived from natural sources: 4 graded stone aggregate 12.5 mm nominal size derived from natural sources) |
| 22 | 5.2.2-Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 23 | 5.3-Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels,bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement: 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 24 | 6.15- Extra for providing and placing in position 2 Nos 6 mm dia. M.S. bars at every third course of half brick masonry. |
| 25 | 9.20.1- Providing and fixing ISi marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and welI matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutte 35 mm thick including ISi marked Stainless Steel butt hinges with necessary screws |
| 26 | 9.96-Providing and fixing aluminium sliding door bolts, ISi marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparentor dyed to required colour or shade, with nuts and screws etc. complete: 9.96.1- 300x16 mm |
| 27 | 9.96.2- 250 x 16 mm |
| 28 | 9.92.1- Providing and fixing chromium plated brass handles with necessary screws etc. complete: 125 mm |
| 29 | 9.74- Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete: 9.74.1- 250 X 10 mm |
| 30 | 9.74.3- 150 x 10 mm |
| 31 | 9.82-Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. |
| 32 | 9.83-Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. |
| 33 | 9.134.1.1.1- Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws : 35 mm thick shutters with ISi marked M.S. pressed butt hinges bright finished of required size Second class teak wood |
| 34 | 9.9.1.1-Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes (weight not less than 10 kg per sqm) fixing with ISi marked M.S. pressed butt hinges bright finished of required size with necessary screws. Second class teak wood 35 mm thick |
| 35 | 9.1.2-Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dashfastener shall be paid for separately). Sal wood |
| 36 | 10.30.2- Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 5.5 mm thick glass panes |
| 37 | 9.48.2-Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc |
| 38 | 13.1- 12 mm cement plaster of mix : 13.1.1 1:4(1 cement: 4 fine sand) |
| 39 | 13.1.2-12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand) |
| 40 | 13.2.2-15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 fine sand) |
| 41 | 13.16.1- 6 mm cement plaster of mix : 1:3 (1 cement: 3 fine sand) |
| 42 | 13.80- Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete |
| 43 | 13.48.1-Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm |
| 44 | 13.45.1-Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm |
| 45 | 13.48.3-Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture |
| 46 | 13.48.2-Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture |
| 47 | 13.7.1-12 mm cement plaster finished with a floating coat of neat cement of mix : 1:3 (1 cement: 3 fine sand) |
| 48 | 11.3.1- Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete, 40 mm thick with 20 mm nominal size stone aggregate |
| 49 | 19.19.1-Man Hole cover ( rectangular shape ) size 600 X 450 mm) |
| 50 | 17.39.1.1- Providing and fixing plain bend of required degree. 100 mm dia Sand cast iron S&S as per IS - 1729 |
| 51 | 6.13.2- Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand) |
| 52 | 1.10-Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C 1.10.3- Group C |
| 53 | 1.11-Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 54 | 1.12-Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required ( @ 15 mtr / Crt ) |
| 55 | 1.14-Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 1.14.1- 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 56 | 1.14.2- 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 57 | 1.14.9- 4 X 6 sq. mm + 2 X 6 sq. mm earth wire |
| 58 | 1.14.10- 4 X 10 sq. mm + 2 X 6 sq. mm earth wire |
| 59 | 1.18- Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 1.18.2- 2 Pair ( @ 15M EACH ) |
| 60 | 1.21- Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 1.21.2- 25 mm |
| 61 | 1.22- Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required. 1.22.1- 75 mm X 75 mm X 60 mm deep |
| 62 | 1.24-Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 1.24.1-5/6 A switch |
| 63 | 1.24.4-3 pin 5/6 A socket outlet |
| 64 | 1.24.6- Telephone socket outlet |
| 65 | 1.25- Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
| 66 | 1.31-Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. ( for light plugs to be used in non residential buildings ) |
| 67 | 1.32-Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. |
| 68 | 1.33- Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required. |
| 69 | 1.34- Supplying and fixing brass batten/ angle holder including connection etc. as required. |
| 70 | 1.41- Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required. |
| 71 | 1.45- Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required. |
| 72 | 1.50- Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. 1.50.1-Upto 450 mm sweep |
| 73 | 1.51- Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes. |
| 74 | 2.4- Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 2.4.1-4 way (4 + 12), Double door |
| 75 | 2.10-Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 2.10.1- Single pole |
| 76 | 2.13-Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 2.13.2 63amps |
| 77 | 4.1-Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 4.1.3-200 mm width X 50 mm depth X 1.6 mm thickness |
| 78 | 5.4-Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. |
| 79 | 5.9-Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) |
| 80 | supply of AC 230/250 volts, 50 Hz energy efficient ceilling fan with standand down rod blades 2 nos. caps etc complete ( Make : Bajaj / compton / havells ) 1200 mm sweep |
| 81 | 900 mm sweep |
| 82 | supply of AC 230/250 , 50Hz exhaust fans including providing nuts, bolts, mounting frame and other accessories ets. completeModel - ventil Air - DC ( Make : Bajaj / compton / havells ) 300 mm sweep 900 rpm |
| 83 | supply and fixing of LEDTube Light wall mounted LED batten , extruded aluminium Heat sink provided for efficient heat dissipation & integrated eletronic driver . ( 1x 22 W LED single 4000 K ) complete in all aspects as per direction of Engineer in charge |
| 84 | SUPPLY OF LED Glass Blub B22, 12W , 6000K / 4000K /3000K, 230/250 volt, 50 Hz etc. complete in all aspects as per direction of Engineer in Charge |
| 85 | 18.10.3- 25 mm dia nominal bore |
| 86 | 18.46-Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 18.46.2-20 mm dia nominal bore |
| 87 | M.R-Providing and fixing KUB 35053 F bib cock wih wall Flange make quarter turn jaquar |
| 88 | M.R- Providing and fixing KUB 35053 F Angular stop cock wih wall Flange make quarter turn jaquar |
| 89 | 18.21.2.1-Providing and fixing uplasticised PVC connection pipe with brass unions 15 mm nominal bore |
| 90 | 18.18- Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 8.18.3- 25 mm nominal bore |
| 91 | 18.51.1-Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore |
| 92 | 17.2.1-Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid |
| 93 | 17.7.1-Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps |
| 94 | 18.9-Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge 18.9.9- 100 mm nominal dia Pipes |
| 95 | 18.9.8- 75 mm nominal dia Pipes |
| 96 | 17.37- Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : 17.37.1- For 100 mm dia pipe |
| 97 | 17.37.2- For 75 mm dia pip |
| 98 | 17.60.1.1- Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 100 mm outlet Sand cast iron S&S as per IS: 3989 |
| 99 | 18.53.1- 18.53 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore |
| 100 | 17.32.1- Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Circular shape 450 mm dia |
| 101 | 17.33- Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 102 | 17.72- Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. |
| 103 | 18.65- Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements, weighing not less than 106 gms. |
| 104 | 17.42- Providing and fixing double equal plain junction of required degree. 100x100x100x100 mm 17.42.1.1- 100 X100 X100 mm |
| 105 | 17.42.2.1- 75 X75 X75 mm |
| 106 | 17.40- Providing and fixing heel rest sanitary bend Providing and fixing bend of required degree with access door insertion rubber washer 3mm thick, bolts and nutes complete 17.40.1.1- 100mm diameter pipe |
| 107 | 17.40.2.1- 75 mm diameter pipe |
| 108 | 17.10.1.1-Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 250 mm |
| 109 | As per Quotation Hand and power Operated chaff cutter with 2hp Motor (M.R.) |
| 110 | As per Quotation BORE WELL |
| 111 | As per Quotation COW DUNG LOG MAKING MACHINE Please Enable Macros to View BoQ information |
