|
| 1 | Providing and fixing of Chest Press Double Size / Dimensions Length -1200 milimeterWidth- 700 milimeterHeight – 1800 milimeterMaximum weight -120 kilogramMaterial:- All the pipes shall be Galvanized Iron (GI) and ISI marked to ensure strength, durability, and corrosion resistance. The main central pipe shall be an 80 mm NB GI pipe, while the handle frame and sheet frame shall each consist of 40 mm NB GI pipes. The connecting links shall be made of 32 mm NB GI pipes, and the footrest pipe shall also be 32 mm NB GI. The mild steel (MS) foundation plate shall have a minimum thickness of 12 mm. The foundation pipe shall consist of a GI pipe anchored 750 mm deep and supported with an MS angle of 25×25×4 mm for stability. The seat and backrest shall be made of high-density polyethylene (HDPE) sheets with a thickness of 3 mm, designed with a uniform bending radius to avoid sharp edges and ensure user safety. All nuts and bolts used for assembly shall be made of galvanized iron (GI) to enhance durability and resistance to corrosion. The movement mechanism shall be fitted with ball bearings that are self-lubricating and sealed to protect against rain, dust, and other environmental elements. The closing caps of open ends of all pipes, as well as bearings, bushes, and bases, shall be covered with fibre-reinforced plastic (FRP) closing caps having a minimum thickness of 3 mm. All plastic components shall be UV-stabilised and weather-resistant to ensure long-lasting performance in outdoor conditions.Colour:- Green Paint finish- Power coated, UV resistantPaint coating thickness (min) – 100 micrometerWarranty – 3 years.Complete in all respects, including installation of equipment in a cement concrete block of size 5’ x 5’ x 1¼’, to the entire satisfaction of the Engineer-in-Charge. |
| 2 | Providing and Fixing of Leg Press – LEG SHAPER complete in all respects having following specifications.a) All pipes should used in the equipments should be galvanised with 3mm thickness.b) Multi Colour Powder coating with polyster paints should be used on all the equipments.c) The foot pedal on all the equipments should be of aluminium only.d) The seats should be made of high quality plastic with colour scheme in yellow or orange.e) The high end bearings such as SKF/NBC must be used in all the equipments.1 Dimensions- 1730*450*1450mm2 Colour- customizable multi colour and complete powder coat3 Size of main tube-114*3.75mm steel pipe4 Size of supporting tube-76*3mm steel pipe5 There is restrainer inside, the distance between swing arm and main tube is greater than 230mm avoiding the danger of getting stuck.6 Al alloy protecting covers are used at the top other main tubes to protect from the rainwater7 Anti-skid components are used at the pedal parts.8 The distance between two spinners is no less than 230mm, avoiding the damage of being stuck9 Anti theft cover is made by stainless steel/high quality plastic.10 Thickness of bearing bracket is no less than8mm11 Hazardous materials like coating agent, rubber are under national newest standard.Functions: Develops the strength of lower limbs, and improves the stability and agility of three main joints of lower limbs; good for the healing of inconvenience of bending and stretching of lower limbs, and muscular atrophy of lower limbs, rheumatoid arthritis, sciatica, sprain of the anklebone, etc. Approaches: Sit on the chair and step on the footboard. Stretching legs with force and recover slowly. Repeat. Users: Suitable for people of different ages.Complete in all respects, including installation of equipment in a cement concrete block of size 5’ x 5’ x 1¼’, to the entire satisfaction of the Engineer-in-Charge. |
| 3 | Providing and Fixing of Parallel Bars Size/DimensionsLength- 900 millimeterHeight – 800 millimeterMaterial:- All the pipes shall be Galvanized Iron (GI) and ISI marked to ensure strength and durability. The vertical or standing pipes shall be 40 mm NB with a thickness of 2.9 mm, and the horizontal pipes shall also be 40 mm NB with a thickness of 2.9 mm. The foundation pipe shall consist of a GI pipe anchored 500 mm deep and supported with a mild steel (MS) angle of 25×25×4 mm. The nominal bore of the foundation pipe shall be 40 mm NB with a thickness of 2.9 mm. The MS foundation plate shall have a minimum thickness of 12 mm. All nuts and bolts used for assembly shall be made of stainless steel to provide durability and resistance to corrosion. The open ends of all pipes, bearing bushes, and bases shall be fitted with fibre-reinforced plastic (FRP) caps having a minimum thickness of 2 mm. All plastic components shall be UV-stabilised and weather-resistant to ensure long-lasting performance under outdoor conditions.Colour:- Paint finish- Power coated, UV resistantPaint coating thickness (min) – 80 micrometerWarranty - 3 years.Complete in all respects, including installation of equipment in a cement concrete block of size 5’ x 5’ x 1¼’, to the entire satisfaction of the Engineer-in-Charge. |
| 4 | Providing and fixing of Air walker/Stroller Single Size / Dimensions Length -1100 millimeterWidth- 460 millimeterHeight – 1480 millimeterMaximum weight – 100 kg.Material:- All the pipes shall be Galvanized Iron (GI) and ISI marked to ensure strength, durability, and corrosion resistance. The main frame shall be made of 100 mm NB GI pipe, while the leg movement frame shall consist of 40 mm NB GI pipe, and the handle frame shall be constructed using 32 mm NB GI pipe. The movement mechanism shall be equipped with ball bearings that are self-lubricating and sealed to provide protection against rain, dust, and other environmental factors. The footrest shall be made of high-density polyethylene (HDPE) for enhanced durability and user comfort. The foundation pipes shall be GI pipes anchored 750 mm deep and supported with mild steel (MS) angles of 25×25×4 mm. The nominal bore of the foundation pipe shall be 100 mm, while the MS foundation plate shall have a minimum thickness of 10 mm. All nuts and bolts used for assembly shall be made of galvanized iron (GI) to ensure long-lasting durability and corrosion resistance. The open ends of all pipes, as well as the bearings, bushes, and bases, shall be fitted with HDPE closing caps having a minimum thickness of 2 mm to provide a neat finish and additional protection. All plastic components shall be UV-stabilised and weather-resistant to ensure long-lasting performance in outdoor conditions.Colour:- Paint finish- Power coated, UV resistantPaint coating thickness (min) – 100 micrometerWarranty - 3 years.Complete in all respects, including installation of equipment in a cement concrete block of size 5’ x 5’ x 1¼’, to the entire satisfaction of the Engineer-in-Charge. |
| 5 | Providing and fixing of Three wheel shoulder Builder/ Arm wheel Size / Dimensions Height of central Pole from ground -1524 millimeterOutside diameter of first wheel - 850 millimeterOutside diameter of second wheel - 800 millimeterOutside diameter of third wheel - 650 millimeter Height of first wheel from ground - 1220 millimeterHeight of second wheel from ground - 1200 millimeterHeight of third wheel from ground - 1180 millimeterMaximum weight -120 kilogramMaterial:- All the pipes shall be Galvanized Iron (GI) and ISI marked to ensure quality and durability. The main central pipe shall be constructed using a 125 mm NB GI pipe, while the ring (wheel) shall be made of a 40 mm NB GI pipe. The spokes of the wheel shall consist of 15 mm NB GI pipes, with a total of six spokes per wheel. The foundation pipes shall be GI pipes anchored 750 mm deep, supported with mild steel (MS) angles of 25×25×4 mm, and shall have a nominal bore of 125 mm. The MS foundation plate shall have a minimum thickness of 12 mm. All nuts and bolts used for assembly shall be made of stainless steel to ensure durability and resistance to corrosion. The movement mechanism shall be equipped with ball bearings, which shall be self-lubricating and sealed to provide protection against rain, dust, and other environmental factors. The open ends of pipes, bearings, bushes, and bases shall be fitted with high-density polyethylene (HDPE) closing caps having a minimum thickness of 2 mm. All plastic components shall be UV-stabilised and weather-resistant to ensure long-lasting performance in outdoor conditions.Colour:- Paint finish- Power coated, UV resistantPaint coating thickness (min) – 80 micrometerWarranty -4 years.Complete in all respects, including installation of equipment in a cement concrete block of size 5’ x 5’ x 1¼’, to the entire satisfaction of the Engineer-in-Charge. |
| 6 | Providing and fixing of double Surf Board Size / Dimensions Length -950 millimeterWidth- 700 millimeterHeight – 1300 millimeter Maximum weight -120 kilogramMaterial :- All the pipes shall be Galvanized Iron (GI) and ISI marked to ensure quality, strength, and durability. The main central pipe shall be made of 150 mm NB GI pipe with a thickness of 4.5 mm. The movement frame pipe shall be 32 mm NB with a thickness of 4 mm, while the connecting link pipes shall be 32 mm NB with a thickness of 2.6 mm. The handle frame pipe shall be 25 mm NB with a thickness of 2.6 mm. The foundation pipes shall consist of GI pipes anchored 500 mm deep and supported with mild steel (MS) angles of 25×25×4 mm, having a nominal bore of 100 mm. The MS foundation plate shall have a minimum thickness of 12 mm. The movement mechanism shall be equipped with ball bearings that are self-lubricating and sealed to provide protection against rain, dust, and other environmental factors. All nuts and bolts used for assembly shall be made of galvanized iron (GI) to ensure long-lasting durability and corrosion resistance. The footrest shall be made of fibre-reinforced plastic (FRP) for strength and user comfort. The open ends of all pipes, bearings, bushes, and bases shall be fitted with GI closing caps having a minimum thickness of 3 mm. All plastic components shall be UV-stabilised and weather-resistant to ensure long-lasting performance in outdoor conditions.Colour:- Paint finish- Power coated, UV resistantPaint coating thickness (min) – 80 micrometerWarranty - 2 years.Complete in all respects, including installation of equipment in a cement concrete block of size 5’ x 5’ x 1¼’, to the entire satisfaction of the Engineer-in-Charge. |
| 7 | Providing and Fixing of Sit Up Board.WAB BOARD complete in all respects having following specifications.f) All pipes should used in the equipments should be galvanised with 3mm thickness.g) Multi Colour Powder coating with polyster paints should be used on all the equipments.h) The foot pedal on all the equipments should be of aluminium only.i) The seats should be made of high quality plastic with colour scheme in yellow or orange.j) The high end bearings such as SKF/NBC must be used in all the equipments.Sit Up Board or Abbs Shaper Size:-972x980x462 mm Two Wab Boards are raised on the pendulum pillar for exercising and agility of the abdomen and muscles. Functions: Developing the strength and flexibility of lumbar and abdominal muscles consuming the fat in waist and abdomen, good for figure shaping and bodybuilding. Approaches: Hang up the round pipe with feet, crossing the hands behind head, making body backward to the trainer, recovers.Complete in all respects, including installation of equipment in a cement concrete block of size 5’ x 5’ x 1¼’, to the entire satisfaction of the Engineer-in-Charge. |
| 8 | Providing and fixing of Double Twister( One standing and One Sitting) Size / Dimensions Length -1400 millimeterWidth- 680 millimeterHeight – 900 millimeter Maximum weight - 100 kilogramMaterial:- All the pipes shall be Galvanized Iron (GI) and ISI marked to ensure quality, strength, and durability. The main central pipe shall be made of 100 mm NB GI pipe with a thickness of 4.5 mm. The standing/sitting twister frame pipe shall be 32 mm NB GI pipe with a thickness of 4 mm, while the rotating disk support pipe at the bottom shall be 80 mm NB GI pipe with a thickness of 3.2 mm. The handle frame pipe shall be 25 mm NB GI pipe with a thickness of 3.2 mm. The foundation pipes shall consist of GI pipes anchored 750 mm deep and supported with mild steel (MS) angles of 25×25×4 mm, having a nominal bore of 100 mm. The MS foundation plate shall have a minimum thickness of 10 mm. The movement mechanism shall be equipped with roller bearings that are self-lubricating and sealed to provide protection against rain, dust, and other environmental elements. All nuts and bolts used for assembly shall be made of galvanized iron (GI) to ensure durability and corrosion resistance. The footrest shall be made of aluminum casting for enhanced strength and stability. The open ends of all pipes, as well as bearings, bushes, and bases, shall be fitted with fibre-reinforced plastic (FRP) closing caps having a minimum thickness of 2 mm to provide a smooth finish and additional protection. All plastic components shall be UV-stabilised and weather-resistant to ensure long-lasting performance in outdoor conditions.Colour:- BluePaint finish- Power coated, UV resistantPaint coating thickness (min) – 80 micrometer Warranty - 2 years.Complete in all respects, including installation of equipment in a cement concrete block of size 5’ x 5’ x 1¼’, to the entire satisfaction of the Engineer-in-Charge.. Please Enable Macros to View BoQ information |
