Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Complete design & drawing of Fire Fighting System at Store Centre By Authorised Designer as per site Requirments direction of E/I & guide lines provided by CPWD General sepecification of works part-V (Wet Riser & sprinkler system) 2020. NSI |
| 2 | Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : For 80mm Dia.(DSR 18.7.6) (Electrical E&M) |
| 3 | Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : For 100mm Dia.(DSR 18.7.7) (Electrical E&M) |
| 4 | Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : For 150mm Dia. (DSR 18.7.8) (Electrical E&M) |
| 5 | Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. 200 mm. dia (wall thickness = 6.3 mm). DSR (18.6.1) (Electrical E&M) |
| 6 | Supplying, installation, testing & commissioning of heat detector operating at 54ºC/57ºC with rate of rise cum fixed temperature (dual thermistor) type with mounting base complete with all connection etc. as required. DSR (17.1.1) (Electrical E&M) |
| 7 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid. DSR Code 17.2.1 |
| 8 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate DSR Code 11.3.1 |
| 9 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 10 litre capacity - White DSR Code 17.18.1 |
| 10 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap. DSR Code 17.7.4 |
| 11 | Supplying, installation, testing & commissioning response indicator on surface/recess MS box having two LEDs metallic cover complete with all connections etc. as required . DSR (17.1.5) (Electrical E&M) |
| 12 | Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required. DSR (17.1.6) (Electrical E&M) |
| 13 | Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required.6 Zone. DSR (17.1.9.2) (Electrical E&M) |
| 14 | Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : For 32mm Dia. DSR (18.7.2) (Electrical E&M) |
| 15 | Providing and fixing PVC BALL FLOAT VALVE 15 mm dia. WITH BRASS & UNION COMPLETE, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. NSI Ref. CSI No. 26.06 (a) (SOR 23-24) |
| 16 | Providing and fixing CP BRASS BIB COCK15 mm dia. HEAVY QUALITY ( 400gm) ( L & K and equi.) fittings, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. NSI Ref. CSI No. 26.16 (a) (SOR 23-24) |
| 17 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore DSR 18.49.1 |
| 18 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931. 15mm nominal bore DSR 18.53.1 |
| 19 | Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : For 40mm Dia. DSR (18.7.3) (Electrical E&M) |
| 20 | Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : For 65mm Dia.(DSR 18.7.5) (Electrical E&M) |
| 21 | Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : For 50mm Dia. DSR (18.7.4) (Electrical E&M) |
| 22 | Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : For 25 mm Dia. DSR (18.7.1) (Electrical E&M) |
| 23 | Providing and Fixing one coat of 4mm thick ‘PYPKOTE’ or COATEK anti rust pipe protection layer of approved make and quality including approved make primer as per manufactures specification and over lap of 25mm to make an impermeable layer on above MS Pipe 80MM dia size in trenches structural/ masonary etc. complete including surface prepration, cost of all Materials, Labours and T&P etc. as per direction of E/I. NSI |
| 24 | Providing and Fixing one coat of 4mm thick ‘PYPKOTE’ or COATEK anti rust pipe protection layer of approved make and quality including approved make primer as per manufactures specification and over lap of 25mm to make an impermeable layer on above MS Pipe size 200mm dia (under ground pipe) in trenches structural/ masonary etc. complete including surface prepration, cost of all Materials, Labours and T&P etc. as per direction of E/I. NSI |
| 25 | Providing and Fixing one coat of 4mm thick ‘PYPKOTE’ or COATEK anti rust pipe protection layer of approved make and quality including approved make primer as per manufactures specification and over lap of 25mm to make an impermeable layer on above MS Pipe size 150mm dia (under ground pipe) in trenches structural/ masonary etc. complete including surface prepration, cost of all Materials, Labours and T&P etc. as per direction of E/I. NSI |
| 26 | Providing and Fixing one coat of 4mm thick ‘PYPKOTE’ or COATEK anti rust pipe protection layer of approved make and quality including approved make primer as per manufactures specification and over lap of 25mm to make an impermeable layer on above MS Pipe size 100mm dia (under ground pipe) in trenches structural/ masonary etc. complete including surface prepration, cost of all Materials, Labours and T&P etc. as per direction of E/I. NSI |
| 27 | Providing and Fixing one coat of 4mm thick ‘PYPKOTE’ or COATEK anti rust pipe protection layer of approved make and quality including approved make primer as per manufactures specification and over lap of 25mm to make an impermeable layer on above MS Pipe size 50mm dia (under ground pipe) in trenches structural/ masonary etc. complete including surface prepration, cost of all Materials, Labours and T&P etc. as per direction of E/I. NSI |
| 28 | Providing and Fixing one coat of 4mm thick ‘PYPKOTE’ or COATEK anti rust pipe protection layer of approved make and quality including approved make primer as per manufactures specification and over lap of 25mm to make an impermeable layer on above MS Pipe size 25mm dia (under ground pipe) in trenches structural/ masonary etc. complete including surface prepration, cost of all Materials, Labours and T&P etc. as per direction of E/I. NSI |
| 29 | Supply, fixing and testing in position ISI marked and approved make cast iron butter fly valve including all interal fittings of 80MM size with MS flange, nuts, bolts and rubber gaskets etc. including its testing and cost of all Materials, Labours and T&P etc. as per direction of E/I.(ISI marked. Make- Kartar, Castle, Audco) NSI |
| 30 | Supply, fixing and testing in position ISI marked and approved make cast iron wafer type non return valve including all interal fittings of 80mm size with MS flange, nuts, bolts and rubber gaskets etc. including its testing and cost of all Materials, Labours and T&P etc. as per direction of E/I. (ISI marked. Make- Kartar, Castle, Audco) NSI |
| 31 | Supply and installation of two way 63mm instantaneous inlet for fire brigade connection including provision of cast iron Butter fly valve the cost of butter fly valve shall be under separate item and making connection with 100NB fire fighting pipe, painting with fire red paints completing the work in all respect as per the direction of E/I Make- New age, Padmani, Guard, HS. NSI |
| 32 | Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :2 way-100 mm dia M.S. Pipe (DSR 18.19.1) (Electrical E&M) |
| 33 | INCOMING250A, 50kA 4 Pole MCCB, lcs=100% lcu rating Digital Voltmeter 0-500V with selector switch, Digital Ammeter (0-250 A) with selector swtich & CTs etc. LED type RYB phase indicating lamps, ON, OFF, trip indicating lampsSet of Copper Bus Bar 300A OUTGOING-( Note : All outgoing feeders for pumps should have digital Ammeter with selector switches, and LED type ON, OFF, trip indicating lamps)Main Fire Pump-125 A, 50kA TPN MCCB, lcs=100% lcu, with fully automatic Star/Delta starter suitable for 60 HP pump with overload protection, current sensing type single phase preventer complete with all acceessories and internal wiring required for automatic operation, selector switch for local/remote, auto/manual/OFF operation.Jockey Pump-63 A, 50kA TPN MCCB, lcs=100% lcu, with suitable HP fully automatic Star/Delta starter with overload protection, current sensing type single phase preventor complete with all acceessories and internal wiring required for automatic operation, selector switch for local/remote; auto/manual/OFF operation. Diesel Engine Control-Control for diesel engine comprising -Automatic/Manual selctor switch & 3 attempts starting device, timers and relays as required, push buttons, start/stop in manual mode Indicating lamp for high/ Low Lub. Oil pressure, High Water Temp and Engine on indication. Battery charger suitbale for 12V/24 V DC with boost and trickle selector switch, 0-30 V DC volt meter,and 0-20 A DC Ammeter. All standard relays and accessories for automatic operation of diesel engine. System Controller-Designing, Supply, Installation, Testing and comm1ss1oning of system controller to control operation of main electric fire pump, diesel pump, Pressurization pump, Terrace pump in sequence as per specification consisting of relays, timers. Sensors, annunciation window for fault indication,complete as per specification. DSR (18.5.1) (Electrical) |
| 34 | Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as requ ired :Single headed Stainless steel (DSR 18.9.2) (Electrical E&M) |
| 35 | Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required :Single headed Stainless steel (DSR 18.10.2) (Electrical E&M) |
| 36 | Supply, fixing, testing and commissioning of 20mm dia bore and 30 meter long hose rubber lined Dunlop pipe and hose reel for first aid fire fighting confirming to IS 384 with full swing drum fixing brackets 5 mm dia shut off gunmetal brass nozzle 25 mm dia globe valve connection to the landing valve through adopter or directly from the riser through 25 mm dia GI pipe as required including 25 mm dia pipe length with all sockets, elbows and nipples etc. including providing and operating instruction on a metal plate and fixing it near hose reel The system shall be complete in all respect as per drawing including cost of all Materials, Labours and T&P etc. as per direction of E/I.(Make- Newage,Padmani, Guard, HS). NSI |
| 37 | Providing and fixing gun metal /S.S. ISI marked 63 mm dia branch pipes and 20 mm dia nozzle as per IS 903 of approved make and quality as required. including cost of all Materials, Labours and T&P etc. as per direction of E/I.( Make- HS,Newage, Superex, Padmani) NSI |
| 38 | Providing and fixing ISI Marked fire RRL hose pipe 15 meter long and 63 mm dia with ISI marked IS 903 gun metal male and female coupling of approved make and quality as required near wet riser including cost of all Materials, Labours and T&P etc. as per direction of E/I. (Make- CRC, Newage, Padmani,HS). NSI |
| 39 | Providing and fixing Hose cabinet box size 600X750X250MM made of 16 gauge M.S sheet duly painted with PO red paint 03 coats with central 6mm thick glass door, lock handle and fixing support on wall Including cost of all Materials, Labours and T&P etc. as per direction of E/I. NSI |
| 40 | Supply, fixing, testing & commissioning of electrical motor driven fire pump suitable for automatic operation of following jockey pump.(Make- Kirloskar, Crompton ) of Model no. D.B. 32/20 horizontal end suction type (a) Horizontally mounted centrifugal fire pump complete for delivery of 180 LPM against a total head of 50 meter with necessary pressure gauge of approved make including by pass arrangement for periodic testing of the working of the pump set with required length and size of pipe.The impeller shall be enclosed type and accurateky balanced dynamically The pump casing shall be of cast iron, impeller shall be of bronze and shaft shall be stainless steel (b) Squirrel cage TEFC induction motor (2900 RPM) Crompton/Kirloskar/ABB as per IS 325-1978 suitable for 415 volt 3 phase 50 HZ (10 HP) for the above pump and flexible coupling with the pump. (c) Common bed plate of fabricated mild steel channel or cast iron type. (d) Suitable. cement concrete pump foundation and vibration clamping arrangement as required. (e) Pressure switch for pump for automatic operation including necessary wiring up to control panel. NSI |
| 41 | (A) Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump)(B). Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520.(C). Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325.(D). M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required.(E). Suitable cement concrete foundation duly plastered and with anti vibration pads. 180 lpm at 56 m Head DSR (18.3.3) (Electrical E&M) |
| 42 | (A) Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump)(B). Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520(C) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325.(D) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required.(E) Suitable cement concrete foundation duly plastered and with anti vibration pads. 450 lpm at 35 m Head DSR (18.4.2) (Electrical E&M) |
| 43 | Supply, fixing, testing & commissioning of Diesel engine driven fire pump suitable for automatic operation consisting of following for hydrant system. (Make- kirloskar, Crompton) of model no. D.B. 100/32 horizontal end suction type (a) Horizontally mounted centrifugal fire pump model No DB/100/32 complete for delivery of 1850 LPM against a total head of 50 meter so as to ensure a minimum pressure of 30 meter at highest and farthest outlet at the specified flow complete with necessary pressure gauge including by pass arrangement for periodic testing of the working of the pump set. The pump casing shall be of cast iron, impeller shall be of bronze and shaft shall be stainless steel. (b) Squirrel cage, TEFC induction diesel engine Model 3R1040 1800RPM 43 BHP for the above pump and flexible coupling with the pump with 1800 RPM 65 % efficiency without negative tabeance (c) Common bed plate of fabricated mild steel channel or cast iron type. (d) Suitable cement concrete pump foundation and vibration clamping arrangement as required. (e) Pressure switch for automatic operation of motor including necessary wiring up to control panel. NSI |
| 44 | Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :For 80 mm dia (DSR 18.11.4 ) (Electrical E&M) |
| 45 | Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :For 100 mm dia (DSR 18.11.5) (Electrical E&M) |
| 46 | Supply, installation, testing & commissioning of Diesel Engine driven pump exhaust M. S. Pipe calss \\"C\\" 150mm dia including fittings like flanges, bends, reducers etc. 50mm thick fibre wool insulation aluminium cladding, 21 gauge, necessary excavation, fixing of silender connections at engine exhaust, necessary supports, back filling, cutting and making good, bird proff and weather proof flap complete in all respect. NSI |
| 47 | Supply, installation, testing and commissioning of Monoblock Pump, \\"KIRLOKSKAR/ CROMPTON\\" make 44 mt. HEAD, 2900 RPM, TEFC motor, 7.5 HP directly coupled to Pump having 450 LPM discharge with bronze impeller, Mechanical seal and MS shaft, mounted on common base plate with coupling and coupling guard. NSI |
| 48 | Supply, installation, testing and commissioning of standard Fireman's Axe (tested for 20000 Volts) with heavy insulated rubber handle (ISI marked). NSI |
| 49 | Supply, installation, testing and commissioning of CI Ball Valve, 25mm dia, \\"KARTAR\\" make (For Hose Reel). NSI |
| 50 | Supply, Installation, testing & commissioning of single plate Non Return Valve, 150 mm dia, ISI marked, “KARTAR” make with fittings viz. flange, nut-bolt & rubber insertion etc. NSI |
| 51 | Supply, installation, testing and commissioning of Pressure Switch, IPS 100, “INDFOS” make 0 to 7 bar (Adustable) with socket, nipple, ball valve etc. (One each for Main Electrical, Diesel Engine driven & Jockey Pump at delivery). NSI |
| 52 | Supply, installation, testing and commissioning of Water cum Foam Monitor, 63mm dia “WIMCO/ NEWAGE/ HD” make complete with aluminum nozzle, made out of seamless hot dip galvanized pipe and gun metal couplings having locking arrangement etc. capable of moving to any direction in 360 degree angle horizontally and 105 degree angle vertically with Reqired siz Butterfly Valve, matching flanges, nut bolt etc. (Note: cost oo butter fly Valve is in the separate item), pressure 20 bar , LPM 1750 or more. NSI |
| 53 | Supply, installation, testing and commissioning of gun metal single acting Air Release Valve (Spring loaded)with screwed inlet 25mm dia. Make \\"KARTAR\\" K616 or eqivqlent. NSI |
| 54 | Supply, installation, testing and commissioning of 01 Inch stainless steel FB5X Foam making nozzle for pipe size 100mm dia SS grade 304W, flow rate 225 LPM, Length 455 mm and working pressure 8kgf/Sqcm. NSI |
| 55 | Supply, installation, testing and commissioning of Foam chemical, AFFF- 6%, ISI marked, IS: 4989, \\"FIRECHEM\\" Make (Available in 20 ltrs. Capactiy PVC drum). NSI |
| 56 | Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required : For 150mm dia (DSR 18.12.6) (Electrical E&M) |
| 57 | Supply, installation, testing and commissioning of Water cum Foam Monitor, 100mm dia “WIMCO/ NEWAGE/ HD” make complete with aluminum nozzle, made out of seamless hot dip galvanized pipe and gun metal couplings having locking arrangement etc. capable of moving to any direction in 360 degree angle horizontally and 105 degree angle vertically with 100mm Butterfly Valve, matching flanges, nut bolt etc. (Note: cost of 100mm butter fly Valve is in the separate item), flow 7Kg/Sqcm, LPM 3750 or more. NSI |
| 58 | Supply, installation, testing and commissioning of Mild steel FB5X Foam making branch pipe, 150 PSI, size standard. NSI |
| 59 | Supply, installation, testing and commissioning of Electric Motor Driven 40 H.P Fire pumping set suitable for automatic operation consisting of the following as per specifications (Make Kirlosker, Crompton) Pump Model DB-80/20:(a) Horizontally mounted, centrifugal type single fire pump having cast iron body, gunmetal/ bronze impeller, stainless steel shaft and capable of delivering 97 m3/ hr (1620 LPM) against a total head of 70 Mtrs. (b) Squirrel cage induction motor totally enclosed fan cooled type suitable for 400/400 volts (+5%) 3 phase, 50 Hz. A. C. supply of suitable capacity of not less than 40 HP for the above pump with synchronous speed of 2900 RPM confirming to IS: 325 and duly coupled with above pump with flexible coupling including earthing as per relevant Indian standard and specifications (c) Common bedplate for mounting pump and motor fabricated of suitable M.S. channel as per manufacturer’s recommendations. NSI |
| 60 | Supply, installation, testing and commissioning of cubical type floor mounted fire pump control panel fabricated from 16 Gauge M.S. sheet duly painted with stove enameled finish of approved make & shade and comprising of: (a) One incoming 250 ampere MCCB switch unit with 250 AMP MCCB AMP Tpn Busbar Volt metre, volt meter, selector switch and indication lights. (b) One 250 AMP MCCB unit with 63 AMP HRC fuses. (c) One 63 AMP MCCB unit with 63 AMP MCCB. (d) One fully automatic star delta starter suitable for main pump with overload relay, timer, push buttons and auto manual selector switch.(e) One fully automatic direct on line starter suitable for motor with O/L relay, Push Button and Auto/ manual selector switch. (f) Three phase indicating lamps. (g) Three panel type ampere meters one for each motor with ASS, CTS etc. (h) Three neon indication lamps. (i) Fully automatic diesel engine starting system with battery charger, indicating lights, transformer, rectifier, timer, voltmeter, Amp. Meter, selector switches, push buttons, auxiliary relay etc. NSI |
| 61 | Supply, installation, testing and commissioning of Pressure Gauge, stainless steel, Glycerin filled, 100mm dia 0-10 kg./cm2 “TIPCO/H-GURU” make with socket, nipple, ball valve, U tube etc. (One each for Main Electrical, Diesel Engine driven & Jockey Pump at delivery). NSI |
| 62 | Supply, installation, testing and commissioning of Pressure Switch, IPS 100, “INDFOS” make 0 to 7 bar (Adustable) with socket, nipple, ball valve etc. (One each for Main Electrical, Diesel Engine driven & Jockey Pump at delivery). NSI |
| 63 | Providing and fixing of 6 Sq mm FR PVC insulated 1100 V grade 3 core copper cable of approved make and quality including its connection to main switch board & electric motor etc complete with testing as per direction by E/I. NSI |
| 64 | Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :For 100 mm dia (DSR 18.11.5) (Electrical E&M) |
| 65 | Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :For 150 mm dia (DSR 18.11.6) (Electrical E&M) |
| 66 | Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall speakers complete as required. DSR (17.3.3) (Electrical E&M) |
| 67 | Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required. DSR (17.5.1) (Electrical E&M) |
| 68 | Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required.Speaker cable Single pair, 2-core, 1.5 sqmm. DSR (17.5.3.1) (Electrical E&M) |
| 69 | Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 125mm dia DSR (18.14.6) (Electrical E&M) |
| 70 | Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required. DSR (17.5.2) (Electrical E&M) |
| 71 | Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required.Speaker cable Two pair, 2-core, 1.5 sqmm. DSR (17.5.3.2) (Electrical E&M) |
| 72 | Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along with all ancillaries and accessories like coupler etc. as required. DSR (17.5.4) (Electrical E&M) |
| 73 | Supply, installation, testing and commissioning of Four way Fire Brigade Inlet, “NEWAGE” make cast iron comprising of 63mm gun metal instantaneous male inlet coupling with plug and cap chain as per IS: specification with flange, nut bolt, rubber gasket etc. NSI |
| 74 | Supply, fixing and testing in position ISI marked and approved make cast iron dual plate wafer type non return valve (check valve) including all interal fittings of 150 mm size with MS flange, nuts, bolts and rubber gaskets etc. including its testing and cost of all Materials, Labours and T&P etc. as per direction of E/I. (ISI marked. Make- Kartar, Castle, Audco). NSI |
| 75 | Supply, fixing and testing in position ISI marked and approved make cast iron wafer type non return valve including all interal fittings of 100 mm size with MS flange, nuts, bolts and rubber gaskets etc. including its testing and cost of all Materials, Labours and T&P etc. as per direction of E/I. (ISI marked. Make- Kartar, Castle, Audco) . NSI |
| 76 | Supply, installation, testing and commissioning of Manual Call Point, break glass type The call points should comprises of push button of reputed make enclosed in ABS box with M.S. chain and hammer. The push button will have one pair of normally open and one pair of close contacts. The push button would be on non-shrouded construction. The whole assembly of the push button in ABS box is enclosed on the external ABS front cover, which will be seated in the front means of breakable glass with neoprene gasket. Under normal conditions push button would be in depressed condition so long the front glass cover is broken. The push button will be released by the spring action that should give remote Fire alarm through the contacts. “AGNI” make or Palex. NSI |
| 77 | Supply, installation, testing and commissioning of Optical Smoke Detector, Smoke Detector part of the conventional detectors, \\"SYSTEM SENSOR\\" make. This range of detectors has been produced using the latest in manufacturing and design techniques, pushing out the boundaries of existing conventional detector technology. Combined with the latest state of the art optical chamber the detector provides efficient and accurate detection of fires with a high level of resilience to nonfire environmental influences. NSI |
| 78 | Supply, installation, testing and commissioning of Electronic Hooter with Flasher, 24 volt, DC operatable, made out of M.S. sheet heavy duty duly powder coated with epoxy powder coating, plastic body 500 mtrs. audible range with built in transformer etc. “AGNI” make. NSI |
| 79 | Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required. ( DSR 18.20) (Electrical E&M) |
| 80 | Supply, installation, testing and commissioning of CIDF type Y Strainer, 150 mm dia with flange, nut-bolts & rubber insertion. The strainer shall be of reputed make “KARTAR/ BENDCO”. (One each for Electrical & Diesel Engine driven Pump- for proper filtration of water) NSI |
| 81 | Supply, installation, testing and commissioning of CIDF type Y Strainer, 100 mm dia with flange, nut-bolts & rubber insertion. The strainer shall be of reputed make “KARTAR/ BENDCO”. (One each for Electrical & Diesel Engine driven Pump- for proper filtration of water). NSI |
| 82 | Supply, installation, testing and commissioning of CIDF type Y Strainer, 80mm dia with flange, nut-bolts & rubber insertion. The strainer shall be of reputed make “KARTAR/ BENDCO”. (One each for Electrical & Diesel Engine driven Pump- for proper filtration of water). NSI |
| 83 | Supply, installation, testing and commissioning of 150 mm dia CI Sprinkler Alarm Valve with water motor gong bell and trims as required, pressure gauges, drain valves, ball valves, check valves, strainers etc. Alarm valve shall be UL Listed (for fire fighting of HD or equivalent make).NSI |
| 84 | Supply, installation, testing and commissioning of 100 mm dia CI Sprinkler Alarm Valve with water motor gong bell and trims as required, pressure gauges, drain valves, ball valves, check valves, strainers etc. Alarm valve shall be UL Listed (for fire fighting of HD or equivalent make).NSI |
| 85 | Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :For Horizontal side wall sprinkler .(DSR 18.21.3 (Electrical E&M) |
| 86 | Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :For Concealed sprinkler .(DSR 18.21.4) (Electrical E&M) |
| 87 | Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :For Pendent Sprinkler. (DSR 18.21.1) (Electrical E&M) |
| 88 | Providing and fixing uplasticised PVC connection pipe with brass unions. 30 cm length : 15 mm nominal bore. DSR 18.21.1.1 |
| 89 | Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :For Upright Sprinkler .(DSR 18.21.2) (Electrical E&M) |
| 90 | Supply installation, testing and commissioning of Pendent Q.B. sprinkler, 680 C, \\"HD/SPRAYSAFE/AQUA make or equivalent, UL listed with M.S. Socket 15mm dia, Teflon tape, adhesives etc. NSI |
| 91 | Supply, installation, testing and commissioning of Micro Processor based Fire Alarm Control Panel, Ten Zone “AGNI” make. The panel shall be fully modular in construction with test facility on the front for testing entire circulatory of panel. It shall have glass door locking facility. The control panel shall be compact & lightweight and shall be made out of M. S. sheet heavy duty duly powder coated. The control panel shall be complete with 24 volt battery and battery back up arrangement. The Control Panel shall be having battery charging arrangement, Fire indication, short indication, fault indication, low battery indication, battery charging indication, AC on indication, DC on indication & buzzer. NSI |
| 92 | Supply, Installation, testing & commissioning of single plate Non Return Valve, 100 mm dia, ISI marked, “KARTAR” make with fittings viz. flange, nut-bolt & rubber insertion etc. NSI |
| 93 | Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required:Stainless Steel (Grade 304) (DSR 18.18.2) (Electrical E&M) |
| 94 | Providing all materials and labour & carrying out water proffing treatment of internal surface (positive surface) of under ground water storage tank of RCC with following process : (a) drilling 10 mm dia and 100 mm deep holes in wall surface with 04 holes per sqm (b) insurting PVC nozzles in each hole (c) injecting water profing material (s) with pressure in each hole with prescribed pressure (d) completing with required layers i.e fibre mess, Pidigrout 10M 710 of Dr. Fixit, 113 Fastflex of Dr. Fixit , Pidicrete URP 301 of Dr. Fixit, using cement and course sand etc as per prescribed procedure. NSI |
| 95 | Supply, installation, testing and commissioning of 80 mm dia strainer cum Foot valve along with all accessories with all labour and material cost etc. NSI |
| 96 | Supply, installation, testing and commissioning of 100 mm dia strainer cum Foot valve along with all accessories with all labour and material cost etc. NSI |
| 97 | Providing and fixing full way 10 mm Dia GM gate valve whith wheel, ISI mark heavy quality including supply of all materials , labour and T&P required for proper completion of work. NSI |
| 98 | Supply, laying, testing and commissioning of heavy duty cable ( aluminium conductor PVC insulated armoured served shethed cable 1100Volts grade at adeo\pth of 750 mm below GL over a cushion of 75 mm. thick sand all around and protected with burnt bricks on side and top. On surface the cable run shall be fixed on MS clamp etc of suitable size or as directed by tge engineer-incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamp etc. B8including necessary support clamp, connection legs complete in all respect. 4 core 50 Sqmm (3-1/2 core). PWD 501 (l) |
| 99 | Supply and fixing hexagonal/Round G.P.fan box of approved make made up of 1.0 mm thick ISI Marked G.P.sheet spot welded Four to Eight holes of 25.4 mm for pipe entry of the box. Holes should be semi-shuttered type with 0.5 mm G.P. Sheet made upper & lower cover duly screwed fitted with 300 mm round zink coted M.S Bar X 12 mm & brand name should be embossed. Fixing with wiring conduit laid in the R.C.C. roof before concreting alongwith supply of all material, labour, T&P etc. required for proper completion of the work. PWD No. 1149 |
| 100 | Supply and burying of 600mm x 600mm x 3mm copper plate vertically for earthing with its top at least 3 metres below ground level complete with 20mm dia G.I. pipe and funnel for watering and two earthing lead of two no. 8 SWG copper wire in 15mm dia G.I. pipe up to switch board (from appron to switch board the cost of G.I. pipe and copper wire will be extra) 30cm square C.I. frame with hinged cover masonry housing alternate layers of charcoal/coke and salt at least 150mm thick alround etc. complete in all respect. PWD No. 705 |
| 101 | S/F full way CI Gate valve of 63 mm dia. With wheel , BSI mark heavy quality including supply of all labour , material andT & P for proper completion of work . NSI Ref CSI No. 28.02 (SOR 23-24) |
| 102 | S/F full way 63/65 mm dia Fire hydrant Gun Metal Gate Valve heavy quality including supply of all labour , material andT & P for proper completion of work. NSI Ref CSI No. 28.03 (SOR 2023-24) |
| 103 | P/F Male & Female coupling 63/65 mm dia. Gun metal BSI marked confirming to IS:903 heavy quality including supply of all labour , material and T & P for proper completion of work. NSI Ref CSI No. 28.04 (SOR 23-24) |
| 104 | P/F Short Branch pipe Gun Metal BSI marked heavy quality including supply of all labour , material and T & P for proper completion of work. NSI Ref CSI No.28.05 (SOR 23-24) |
| 105 | P/F 63 mm dia RLL Hose Pipe heavy quality having length 15.0 m including supply of all labour , material andT & P for proper completion of work. NSI Ref CSI No. 28.06 (SOR 23-24) |
| 106 | P/F MS Hose Box Single Door with stand for 15 mt RRL Hose heavy quality including supply of all labour , material andT & P for proper completion of work. NSI Ref CSI No. 28.07 (SOR 23-24) |
| 107 | Placing of 10 KL PVC Tank over slab of 6 m staging including supply of all labour , material andT & P for proper completion of work. NSI Ref CSI No.28.08 (SOR 23-24) |
| 108 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. DSR (2.8.1) |
| 109 | Add to Earth work item (SI No. 4.01 to 4.03) for every additional 30m lead or part thereof or for every additional 1.5M lift or part thereof. NSI Ref CSI No. 4.04 (SOR 23-24) |
| 110 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. DSR 2.27 |
| 111 | Excavating, supplying, stacking and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all lift. DSR 2.25(a) |
| 112 | Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. All kinds of soil. DSR 2.28 (a) |
| 113 | Concrete with 4cm gauge I class brick ballast, coarse sand (F.M. 1.8 to 2.5) and cement in proportion of 12:6:1 in foundations and under floors including supply of all materials, labour and tools and plants etc. required for proper completion. NSI Ref CSI No. 5.01 (SOR 23-24) |
| 114 | Concrete with 4cm gauge stone ballast, coarse sand (F.M. 1.8 to 2.5) & cement in proportion of 12:6:1 in foundations &under floors including supply of all materials, labour and tools and plants etc. required for proper completion. NSI Ref CSI No. 5.02 (SOR 23-24) |
| 115 | Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared. DSR (2.32) |
| 116 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) DSR (4.1.10) |
| 117 | Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification. DSR (4.12) |
| 118 | Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but , excluding cost of reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). DSR (5.12) |
| 119 | Smooth finishing of the exposed surface of R.C.C. work with 6 mm thick cement mortar 1:3 (1 Cement : 3 fine sand). DSR (5.23) |
| 120 | Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. DSR (5.30) |
| 121 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. DSR (10.2) |
| 122 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.- Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). DSR (10.13.1) |
| 123 | 62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete. DSR (11.5) |
| 124 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes- 110 mm diameter DSR (12.41.2) |
| 125 | Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. DSR (12.44) |
| 126 | Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified- 2 mm thick corrugated (2.5\\" or 4.2\\" or 6\\") or step-down (2\\" or 3\\" or 6\\" ) as specified DSR (12.47.1) |
| 127 | Providing & fixing at all heights, levels and locations colour finish Aluminium alloy roofing sheets of alloy IS designation 31500, temper Hx8 conforming to IS 737 and dimensions as per IS code 2676 with characteristics of good formability and corrosion resistance. The profile sheets shall be fixed to truss members in slope or required pitch or curvature with Hex cap headed self drilling/tapping Stainless steel screws M6, 50 mm long with 3 mm EPDM seal washer etc. all inclusive of labour, scaffolding, T&P and sundries etc. complete as per directions of the Engineer-In-Charge. (Cost of truss/frame work shall be paid separately) - 0.71 mm, Aluminium Color coated troughed profile with center to center pitch of 200 mm, depth of 32 mm, overall profile width1092 mm, cover width 1000mm. DSR (12.65.2) |
| 128 | Providing and fixing of Pre-coated colour or mill finish Aluminium Roofing Accessories in 0.71 mm thickness ,Alloy 31500 (IS designation) [Aluminium Alloy (AA) 3004 (ISO designation)] For color, coating shall be 5-7 microns epoxy primer on both sides of the sheet and polyester top coat 15-18 microns, using self drilling/tapping SS screws of size 6 x 50mm with 3mm thick EPDM seal and SS plain washer complete : Precoated/mill finish aluminium Ridges plain (500- 600mm) DSR (12.66.1) |
| 129 | Providing and fixing of Pre-coated colour or mill finish Aluminium Roofing Accessories in 0.71 mm thickness ,Alloy 31500 (IS designation) [Aluminium Alloy (AA) 3004 (ISO designation)] For color, coating shall be 5-7 microns epoxy primer on both sides of the sheet and polyester top coat 15-18 microns, using self drilling/tapping SS screws of size 6 x 50mm with 3mm thick EPDM seal and SS plain washer complete : Precoated/mill finish aluminium Gutter (600 mm over all girth) DSR (12.66.6) |
| 130 | 15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 coarse sand) DSR (13.5.1) |
| 131 | Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) DSR (13.46.1) |
| 132 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.- Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) DSR (15.2.1) |
| 133 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. DSR (15.3) |
| 134 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. DSR 15.56 |
| 135 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar DSR (15.7.4) |
| 136 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. DSR (15.60) |
| 137 | Extra for providing and mixing hardening compound of approved quality as per manufacturer's specification in cement concrete. DSR (16.44) |
| 138 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). DSR 5.2.2 |
| 139 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) DSR 4.1.10 |
| 140 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) DSR Code 4.1.3 |
| 141 | S/F 40 mm thick precast RCC jali (approx 0.5 Sq.M. Size) of approved design with 1:3 cement, coarse sand mortar and 1.6 mm dia M.S.reinforcement with cost of all materials labour and T&P complete including cutting required grooves in walls and grouting. NSI Ref CSI No. 5.17 (SOR 23-24) |
| 142 | Concreting of 40 mm thick RCC trench covers in mild steel frame work with RCC 1:1.5:3 in Cement,Chopan coarse sand (F.M. 1.8 to 2.5) and 2cm gauge graded hard stone ballast with 3mm thick floating coat of neat cement finish on top of cover complete with all labour, materials and placing the same in proper position at required location of cable trench within the substation area. NSI Ref CSI No. 5.18 (SOR 23-24) |
| 143 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) DSR Code 4.1.2 |
| 144 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 50 mm nominal dia Pipes DSR 18.7.6 |
| 145 | Precast cement concrete door sills, chaukhats boundary posts, shelves and similar small work with cement, approved coarse sand (F.M. 1.8 to 2.5) and 2 cm gauge graded approved hard stone ballast in the proportion 1:1.5:3, excluding reinforcement but including fixig the same in position including cost of all other material, labor and T&P . NSI Ref CSI No. 5.22 (SOR 23-24) |
| 146 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). DSR Code 5.3 |
| 147 | Centering and shuttering including strutting, propping etc. and removal of form for Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. DSR 5.9.2 |
| 148 | Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick. DSR 5.9.20 |
| 149 | Centering and shuttering including strutting, propping etc. and removal of form for. Columns, Pillars, Piers, Abutments, Posts and Struts DSR 5.9.6 |
| 150 | Centering and shuttering including strutting, propping etc. and removal of form for. Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick DSR 5.9.21 |
| 151 | Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete. DSR 5.9.1 |
| 152 | Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers. DSR 5.9.5 |
| 153 | RCC work with cement, approved coarse sand (F.M. 1.8 to 2.5) and 2 cm gauge graded approved hard stone ballast like granitet, quartzite etc from Dalla, Jhansi or other quarries in proportion 1:1.5:3 in heavier beams i.e. having span above 6m, excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and T&P.NSI Ref CSI No. 5.26 (SOR 23-24) |
| 154 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) DSR 5.1.2 |
| 155 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) DSR Code 6.1.2 |
| 156 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand) DSR Code 6.1.1 |
| 157 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand) DSR Code 6.4.1 |
| 158 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand) DSR Code 6.4.2 |
| 159 | Brick work in foundation & plinth with old dismantled bricks (supplied by department free of cost) and coarse sand of F.M. 1.8 to 2.5 mortar in 1:6 including supply of all other materials, labour, removing mortar & cleaning of old & used bricks,T&P etc complete. NSI Ref CSI No. 6.18 (SOR 23-24) |
| 160 | Brick work in super structure for 230 mm thick wall with old dismantled bricks (supplied by department free of cost) and coarse sand mortar in 1:6 including supply of all other materials, labour, removing mortar & cleaning of old & used bricks,T&P etc complete. NSI Ref CSI No. 6.19 (SOR 23-24) |
| 161 | Mild Steel or Iron work in heavy sizes such as trusses built up gates, door frames, record, racks roof work gates etc. wrought to required form including holes rivetting or welding where necessary and also fixing in proper position and alignment including cost of all materials supplied by contractor. NSI Ref CSI No. 9.01 (SOR 23-24) |
| 162 | As in item 9.01 above but when steel is to be provided by the department. NSI Ref CSI No. 9.02 (SOR 23-24) |
| 163 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. DSR Code 5.22.6 |
| 164 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. DSR Code 5.22A.6 |
| 165 | Fencing with angle iron post placed at required distance embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire weighing 9.38 kg per 100 m (minimum), between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earth work and concrete work to be paid for separately). Payment to be made per metre cost of total length of barbed wire used. With G.I. barbed wire. DSR 16.18.1 |
| 166 | Supplying at site Angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete. DSR 16.19 |
| 167 | Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides DSR Code 10.29.2 |
| 168 | 12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) DSR Code 13.4.1 |
| 169 | 12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand) DSR (13.4.2) |
| 170 | Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. DSR (10.18) |
| 171 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 15 mm nominal bore DSR 18.18.1 |
| 172 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm nominal bore DSR 18.18.2 |
| 173 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore DSR 18.18.3 |
| 174 | Providing and fixing gun metal non- return valve of approved quality (screwed end) : 25 mm nominal bore. Horizontal DSR 18.19.1.1 |
| 175 | Providing and fixing gun metal non- return valve of approved quality (screwed end) : 40 mm nominal bore. Horizontal DSR 18.19.3.1 |
| 176 | Providing and fixing gun metal non- return valve of approved quality (screwed end) : 50 mm nominal bore. Horizontal DSR 18.19.3.1 |
| 177 | Providing and fixing gun metal non- return valve of approved quality (screwed end) : 80 mm nominal bore. Horizontal DSR 18.19.6.1 |
| 178 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover DSR (10.6.1) |
| 179 | Providing and fixing ball bearing for rolling shutters. DSR 10.7 |
| 180 | Extra for providing mechanical device chain and crank operation for operating rolling shutters. Exceeding 10.00 sqm and upto 16.80 sqm in the area. DSR 10.8.1 |
| 181 | Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 150 mm dia DSR (23.15.2) |
| 182 | Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 200 mm dia DSR (23.15.3) |
| 183 | Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 150 mm clamp DSR 23.14.2 |
| 184 | Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp DSR 23.14.3 |
| 185 | Supply and Fixing of 5 blade Exhaust fan ventile air dx 225 mm of Havells or equivalent make including all material, T&P etc required for proper completion of work as approved by engineer in charge. (NSI), Ref. CSI No. (28.38) SOR 23-24 |
| 186 | Rough cast finish to plasters of different mortars,add extra to plaster items NSI Ref CSI No. 11.11 (SOR 23-24) |
| 187 | Add for extra labour and materials for plaster over rough face of one brick thick wall. NSI Ref CSI No. 11.12 (SOR 23-24) |
| 188 | 2 cm. thick cement plaster in dado or skirting in 1:2 consisting of one part of cement and two parts of approved coarse sand laid in panels finished with 3mm.floating coat of neat cement or cement and marble dust in ratio of 5:1 including supply of all materials, labour & T&P etc. required for proper completion of the work. NSI Ref CSI No.11.13 (SOR 23-24) |
| 189 | Engraving lines in the plaster of the outer face wall vertically and horizontally to display the surface as stone facing as directed by the engineer incharge including labour and T&P etc. required for proper completion of the work (Add for extra labour and T&P etc. required for proper completion of the work (Add for extra labour to all items of plaster). NSI Ref CSI No.11.14 (SOR 23-24) |
| 190 | S/mixing approved water proofing compound (CICO,DR FIXIT etc) in cement mortar in plaster or concrete work in the proportion as recommended by the manufacturer. NSI Ref CSI No.11.15 (SOR 23-24) |
| 191 | Providing (12x15) mm section groove in plaster including all material, labour and T&P etc. required for proper completion of the work. NSI Ref CSI No. 11.16 (SOR 23-24) |
| 192 | Making drip coarse (25x12) mm in 1:2 cement and coarse sand including supply of all materials, labour and T&P etc required for proper completion of work. NSI Ref CSI No. 11.19 (SOR 23-24) |
| 193 | Neat cement punning. DSR 13.18 |
| 194 | Providing and fixing glass strips in joints of terrazo/ cement concrete floors. 40 mm wide and 4 mm thick DSR Code 11.13.1 |
| 195 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm DSR Code 11.41.2 |
| 196 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. DSR 11.39 |
| 197 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge- 150 mm nominal size dia DSR (23.3.2) |
| 198 | Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 150 mm nominal size dia DSR (23.4.2) |
| 199 | Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. DSR (23.8) |
| 200 | Providing and fixing glass strips in joints of terrazo/ cement concrete floors. 40 mm wide and 4 mm thick DSR Code 11.13.1 |
| 201 | Supply and fixing of health faucet for model no-ALD-573 as per direction of engineer in charge. This include cost of labour, material T&P etc for proper completion of work. NSI Ref CSI No. 26.30 (SOR 23-24) |
| 202 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 80 mm thick C.C. paver block of M-35 grade with approved colour design and pattern. DSR Code 16.91.2 |
| 203 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. DSR Code 13.62.1 |
| 204 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One or more coats on old work DSR Code 13.99.1 |
| 205 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre. DSR Code 13.41.1 |
| 206 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC (Volatile Organic Compound ) content less than 50 gram/ litre, of approved brand and manufacturer including applying additional coats wherever required to achieve even shade and colour. Old work (one or more coats) DSR Code 13.81.1 |
| 207 | One priming coat and one coat oil bound distemper on previously old oil bound distemper surfacei ncluding supply of all materials,labour and T&P etc. required for proper completion of the work. NSI Ref CSI No. 13.10 (SOR 23-24) |
| 208 | As in item 13.10 but for every coat after the first coat. NSI Ref CSI No. 13.09 (SOR 23-24) |
| 209 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. DSR Code 13.80 |
| 210 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 80 mm dia nominal bore DSR (18.12.8) |
| 211 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 50 mm dia nominal bore DSR (18.12.6) |
| 212 | Applying BIRLA PUTTY or equivalent putty on previousaly bila putty smoothen surface over one cost of water base cement primer of ICI or equivalent brand for smoothining and leveling of the surface as per requirement and direction of E/I including cost of all material , labour and T&P required for proper completion of work. NSI Ref CSI No. 13.21 (SOR 23-24) |
| 213 | Painting one coat with APEX or equivalent brand weather coat paint on new wall surfaces (well prepared with Birla putty and one coat of primer ICI or equivalent which shall be paid separately) including through washing with water including cost of all materials, labour, T&P required for proper completion of work. (CSI No. 13.22) |
| 214 | Same as in item no 13.22 above but for every coat of additional APEX or equivalent brand weather coat paint . (CSI No. 13.23) |
| 215 | Same as in item 13.22 but for each coat of APEX or equivalent brand weather coat paint .on previously treated surface. NSI Ref CSI No. 13.24 (SOR 23-24) |
| 216 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar DSR Code 15.7.4 |
| 217 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. DSR Code 15.3 |
| 218 | Dismantling cement concrete or brick or granolithic floors including base concrete and including stacking of dismantled materials as directed by the Engineer In-charge within a distance of 60 metres. NSI Ref CSI No. 15.05 (SOR 23-24) |
| 219 | Providing 110mm dia Plain PVC CASING PIPES (Aroma /Supreme) (Pressure10 Kg./ Sqcm.) for making tubewell assembly and cartage to boring site, including cost of all labour, materials and T&P required for assembly making and proper completion of work. NSI Ref CSI No. 19.08 (SOR 23-24) |
| 220 | Providing 110mm dia Slotted PVC CASING PIPES (Aroma /Supreme) (Pressure10 Kg./ Sqcm.) for making tubewell assembly and cartage to boring site, including cost of all labour, materials and T&P required for assembly making and proper completion of work. NSI Ref CSI No. 19.10 (SOR 23-24) |
| 221 | Supply and fixing of PVC top plug of heavy quality including all labour material & T&P. (b)110mm NSI Ref CSI No. 19.20 (b) (SOR 23-24) |
| 222 | Supply and fixing of G.I. (\\"B\\" class ) column pipes JTC/ JINDAL make with column coupling socket as required for proper completion of work including all labour material & T&P. (c) 40mm dia NSI Ref CSI No. 19.22 (c) (SOR 23-24) |
| 223 | Supply and fixing of G.I. (\\"B\\" class ) column pipes JTC/ JINDAL make with column coupling socket as required for proper completion of work including all labour material & T&P. (d) 32mm dia NSI Ref CSI No. 19.22 (d) (SOR 23-24) |
| 224 | Supply and fixing support clamps for column pipes made out of MS flats, pairs of bolt-nuts etc complete with all material, labour, T&P. (d) 40mm NSI Ref CSI No. 19.24 (d) |
| 225 | Supply & installation of electrical control panel of L&T / Havells or equivalent make for submersible pump / pumpset containing contractor relay condenser. b) for 1.5/ 2 H.P pump set single phase NSI Ref CSI No. 19.31 (b) (SOR 23-24) |
| 226 | Supply & Installation of submersible pump of K.S.B/ CALAMA. or eqt. make including cost of labour, T&P and material required for completion of work. b) 1.5 HP outlet 40mm dia. or more, Head 71/36, Discharge 2000/6000 LPH. NSI Ref CSI No. 19.32 (b) (SOR 23-24) |
| 227 | Supply & Installation of submersible pump of K.S.B/ CALAMA. or eqt. make including cost of labour, T&P and material required for completion of work. d) 3 HP outlet 50 mm dia. or more, Head 60/24, Discharge 6000/14000 LPH. NSI Ref CSI No. 19.32 (d) (SOR 23-24) |
| 228 | Supply & Installation of submersible pump of K.S.B/ CALAMA. or eqt. make including cost of labour, T&P and material required for completion of work. g) three phase 10 HP outlet 80 mm dia. or more, Head 63/31, Discharge 20000/50000 LPH (NSI), Ref. CSI No. (19.32g) SOR 23-24 |
| 229 | Supply and fixing of submersible cable Havels or equivalent make, for submersible pump complete in all respect. b) 2.5 mm2 for pump above 1 HP and up to 3 HP. NSI Ref CSI No. 19.33 (b) (SOR 23-24) |
| 230 | Supply & fixing of steel wire rope for submersible pump including cost of labour, T&P and material required for completion of work. NSI Ref CSI No. 19.34 (SOR 23-24) |
| 231 | Supply and filling brick bat in soak pit including all labour,material and T&P etc complete. (for 01 soak pit). NSI Ref CSI No. 6.23 (SOR 23-24) |
| 232 | Cartage of T & P and boring set by manual boring to and fro from site of work. NSI Ref CSI No. 18.19 (SOR 20-21) |
| 233 | Supply and installation of 5H.P. Kirloskar or equivalent make single stage, horizontal, self priming,three phase dewatering pumpset of specification Head 14/16 M, Discharge 13.6/10 LPS, solid handle size 15.5 mm, suction 80 mm, delivery 80 mm, RPM 1500 including cost of 80 mm dia G.I. pipe for suction (3M) and delivery (4.5 M). (NSI), Ref. CSI No. (19.29) SOR 23-24 |
| 234 | Development of tubewell by O.P. Unit (5 HP to 10 HP submersible pump set), including bringing Column pipe for the OP unit, assembling, electric connections, running for required period, dismentling and taking out & carrying away and cleaning the site with cost of all labour, materials, T&P and fuel / Electricity Charges etc required for proper completion of work and as per direction of Engineer-in-charge. NSI Ref CSI No. 19.14 (SOR 23-24) |
| 235 | Drilling bore from G.L. to 180 M B.G.L., work to be completed as per direction of Engineer I/C . As per 19.04 above but for 150 mm dia. boring. from 0 M BGL to 90 M BGL. NSI Ref CSI No. 19.04 H (i) (SOR 23-24) |
| 236 | Supply and fixing C.I. non-return valve ISI marked and approved make with nuts, bolts, packing etc complete including all labour material & T&P. a)80 mm dia. NSI Ref CSI No. 19.23 (a) (SOR 23-24) |
| 237 | Supply and stacking pee gravel properly at levelled ground for measurement as directed by Engineer I/C, including all labour, T&P required for proper completion of work. NSI Ref CSI No. 19.25 (SOR 23-24) |
| 238 | Providing & fixing half turn 80mm dia gate valve, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. NSI Ref CSI No. 26.05H (SOR 23-24) |
| 239 | Providing and fixing NON RETURN REFLEX VALVE, 80 mm dia ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. NSI Ref CSI No. 26.07-H (SOR 23-24) |
| 240 | Providing and fixing SLUICE VALVE, CI 80 mm dia. WITH Wheel. ISS:780 & ISS: 2906 class - I, 'MEC' make, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. NSI Ref CSI No. 26.11a (SOR 23-24) |
| 241 | Supply and fixing of Syntex or equivalent make water storage tank including all materials, labours, T&P etc required for proper completion of work. NSI Ref CSI No. 26.12 (SOR 23-24) |
| 242 | P/F 80 mm dia BRASS WHEEL VALVE, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. NSI Ref CSI No. 26.15-H (SOR 23-24) |
| 243 | Providing and fixing of 110 mm dia PVC pipe 6 Kg/ Sq.cm for with special such as Tee, bend, socket, elbow etc including supply of all labour,material,T & P etc complete required for proper completion of work. NSI Ref CSI No. 26.17 (SOR 23-24) |
| 244 | Supply and fixing of fire extinguisher, ABC Type 6.00 kg. capacity (ISI Marked IS : 15683 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work. UPPWD 1131(A) |
| 245 | Supply and fixing of fire extinguisher, ABC Type 9.00 kg. capacity (ISI Marked IS : 15683 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.UPPWD 1132 (B) |
| 246 | Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) in pavements, laid to required slope and camber in panels as required including consolidation finishing and tamping complete. DSR 16.42 |
| 247 | Extra for providing and mixing hardening compound of approved quality as per manufacturer's specification in cement concrete. DSR 16.44 |
| 248 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level. Concrete of M25 grade with minimum cement content of 330 kg /cum. DSR 5.33.1.1 |
| 249 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level. Concrete of M30 grade with minimum cement content of 350 kg /cum. DSR 5.33.1.2 |
| 250 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works above plinth level upto floor V level. Concrete of M25 grade with minimum cement content of 330 kg /cum DSR 5.33.2.1 |
| 251 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works above plinth level upto floor V level. Concrete of M30 grade with minimum cement content of 350 kg /cum. DSR 5.33.2.2 |
| 252 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 80 mm thick C.C. paver block of M-35 grade with approved colour design and pattern. DSR Code 16.91.2 |
| 253 | Wiring point for light with 1.5 sq. mm.FRLSH PVC insulated multistrand single core copper conductor cable in heavy guage rigid steel conduit pipe concealed in the wall, complete with 14 SWG copper earth continuity wire, piano type switch & ceiling rose/ angle/batten holder on 3 mm thick phenolic laminated backelite sheet etc., complete in all respect, as directed including matching colour. UPPWD 131 (C) |
| 254 | Wiring point for fan / fesh air fan (light duty exhaust fan) with 1 sq.mm. FRLCHLACH PVC insulated multistrand single core copper conductor cable in PVC conduit with 1.5 sq. mm.FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduit.. UPPWD 133 (C) |
| 255 | Wiring point for plug with 1.5 sq. mm.FRLSH PVC insulated multistrand single core copper conductor cable in heavy guage rigid steel conduit concealed in the wall, complete with 14 SWG copper earth continuity wire, piano type switch and socket etc. complete in all respect including matching colour wash. UPPWD 134 (C) |
| 256 | Supply and wiring of submain with two number 4 sq.mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 20 mm dia heavy duty (2 mm thick) PVC conduit with one No. 2.5 sq. mm. FRLSH PVC insulated multistrand copper conductor cable as earth contuiity wire drawn in conduit. UPPWD 216 (C) |
| 257 | Supply and wiring of submain with two number 6 sq. mm. PVC insulated 1100V grade single core aluminium conductor cable in 25 mm dia heavy duty (2 mm thick) PVC conduit with one No. 4 sq. mm. PVC insulated aluminium conductor cable as earth continuity wire drawn in conduit. UPPWD 217 (C) |
| 258 | Supply and wiring of submain with two number 2.5 sq.mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 20 mm dia heavy duty (2mm thick) PVC conduit with 1 number 1.5 sq. mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor as earth continuity wire. UPPWD 1304 (C) |
| 259 | Supply and wiring of submains with 2 nos. 2.5 sq mm & with 1 no earth wire of 1.5 sq mm FRLSH PVC insulated 1100 V grade single core multistrand copper conductor cable in existing PVC conduit complete, including supply of all material, labour and T & P etc. required for proper completion of the work as directed by Engineer in charge. UPPWD 291 |
| 260 | Same as in item 291 but with 2 nos. 4 sq mm and 1 no 2.5 sq mm FRLSH PVC insulated copper conductor cable. . UPPWD 291 (A) |
| 261 | Same as in item 291 but with 2 nos. 6 sq mm and 1 no 4 sq mm FRLSH PVC insulated copper conductor cable. UPPWD 291 (D) |
| 262 | S&F of 6 Amp to 32 Amp. MCB (10 KA) C Curve. UPPWD 1002 CAT-A |
| 263 | S&F of 63 Amp. D.P. Isolator. UPPWD 1005 (B) CAT A |
| 264 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way (4 + 12), Double door. DSR (2.4.1) (Electrical E&M) |
| 265 | S&F surface/flush mounting 4 ways SPN distribution board with additional metal door without MCB complete in all respect, as directed at site by Engineer in charge. UPPWD 1022 (A) CAT A |
| 266 | Supply and fixing of LED Tube Light with batten suitable for up to 1 X 22 watt LED tube light complete including tube etc on surface complete in all respect. UPPWD 1413 CAT AA |
| 267 | Supply and wiring of submain with two number 10 sq.mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 25mm dia heavy guage rigid steel conduit on surface, with one number 10 SWG copper earth continuity wire etc. complete in all respect. (NSI), Ref. UPPWD (Electrical) (213B) |
| 268 | As in item no. 213 (B) but in 25 mm dia heavy duty (2mm thick ) PVC conduit with one number 6 sq. mm. FRLSH PVC insulated multistrand copper conductor cable as earth continuity wire drawn in conduit. (NSI), Ref. UPPWD (Electrical) (213C) |
| 269 | Supply and wiring of submain with two number in 32 mm dia heavy duty (2mm thick ) PVC conduit with one number 10 sq. mm. FRLSH PVC insulated multistrand copper conductor cable as earth continuity wire drawn in conduit.. (NSI), Ref. UPPWD (Electrical) (214C) |
| 270 | S&F of 100 A. 415 V Metal clad TPN CFS complete with HRC fuse etc. on angle iron frame complete in all respect. (NSI), Ref. UPPWD (Electrical) (353) CAT-B |
| 271 | S&F of 200 A. 415 V Metal clad TPN CFS complete with HRC fuse etc. on angle iron frame complete in all respect. (NSI), Ref. UPPWD (Electrical) (354) CAT-B |
| 272 | S&F of 200 Amp. four pole change over switch on 50mm x 50mm x 6mm angle iron frame, including the cost of labour, T&P, painting and other material required for proper completion of the work as per direction and satisfaction of Engineer in charge. (NSI), Ref. UPPWD (Electrical) (379) |
| 273 | Supply and fixing of LED Street light Fitting having die cast aluminium body and diffuser with driver set suitable for 75 to 90 Watt. Confirming to IP 66 and above Protection complete in all respect. CAT-AAA (NSI), Ref. UPPWD No. 1423 |
| 274 | Add for light / fan points with modular type switch in place of piano type switch. UPPWD 187 (A) |
| 275 | Supply and fixing of power plug with 15A/250 volt flush type switch and 5 pin 15A/250V flush type universal socket in suitable M.S. box of 175mm x 100mm x 50mm size with phenolic laminated bakelite sheet cover 3mm thick fixed with brass machine screw and cup washer. UPPWD 1139 |
| 276 | Supply and Fixing of 3 blade ceiling fan 1200 mm of Havells or equivalent including all material, T&P etc required for proper completion of work as approved by engineer in charge. NSI Ref. CSI No. 28.39 (SOR 23-24) |
| 277 | Providing all materials and labour & carrying out water proffing treatment of internal surface (positive surface) of under ground water storage tank of RCC with following process : (a) drilling 10 mm dia and 100 mm deep holes in wall surface with 04 holes per sqm (b) insurting PVC nozzles in each hole (c) injecting water profing material (s) with pressure in each hole with prescribed pressure (d) completing with required layers i.e fibre mess, Pidigrout 10M 710 of Dr. Fixit, 113 Fastflex of Dr. Fixit , Pidicrete URP 301 of Dr. Fixit, using cement and course sand etc as per prescribed procedure. (NSI) Ref. (Rate already sanction by Agr. 58/2022-23) |
| 278 | Supply, installation, testing and commissioning of Electronic Hooter with Flasher, 24 volt, DC operatable, made out of M.S. sheet heavy duty duly powder coated with epoxy powder coating, plastic body 500 mtrs. audible range with built in transformer etc. “AGNI” make. (NSI) Ref. (Rate already sanction by Agr. 58/2022-23 |
| 279 | Hiring charge of Crane with operater and diesel for Shifting DG set and big size transformer on site work as per direction E/I.. (NSI) |
| 280 | Supply and erection of factory fabricated and wired metal clad dust and vermin proof floor mounting panel TPN switch board complete with the following HRC type heavy duty TPN fuse switches with fuses and instrument chamber etc. complete in all respects. The instrument chamber shall be separate and shall comprise of flush type ammeter, voltmerer, selector switches for ammeter and voltmeter, instrument fuses, current transormer etc. The board shall have suitable capacity electroytic alumininum busbars as per IS8623 istulate with heat shrink sleeving and mountend on non hygroscopic supports such as CMC/DMC support with deteachable side covers and shall be suitable for extension on the sides. The switches shall be complete with suitable cable end boxes, reverse entery boxes in case of pedestaal type, cable sockets, compression glands and indicating lamp on incoming etc. The job includes the grounting of the board as per direction of Engineer-in-Charge. All outgoing switches of 315 Amp. and above will be provided with ampere metre current transformers and selector switches and instrument fuses etc. The switches board shall be fabricated with CRCA sheet with a minimum thickness of 1.6 mm/2 mm. Cubicle type switch board shall be of cat A B & B-II and pedestal type for Cat-B and C only. (a) Outgoing (a) 100 Amp. TNP-3 Nos (ii) Cat. B. Cubicle Type (NSI), Ref. UPPWD No. 803 (a-ii) (DSR Electrical E&M) |
| 281 | (b) Outgoing (b) 100 Amp. TNP-2 Nos & 63 Amp TPN-2 Nos (ii) Cat. B. Cubicle Type. Ref. UPPWD No. 803 (b-ii) (DSR Electrical E&M) |
| 282 | (c) Outgoing (c) 100 Amp. TNP-1 No & 63 Amp TPN-3 Nos (ii) Cat. B. Cubicle Type Ref. UPPWD No. 803 (c-ii) (DSR Electrical E&M) |
| 283 | (d) Outgoing (d) 63 Amp. TNP-5 Nos (ii) Cat. B. Cubicle Type. Ref. UPPWD No. 803 (d-ii) (DSR Electrical E&M) |
| 284 | (e) Outgoing (e) 200 Amp. TNP-1 No & 32 Amp. TPN-1 No (ii) Cat. B. Cubicle Type. Ref. UPPWD No. 803 (e-ii) (DSR Electrical E&M) |
| 285 | Demolishing R.B. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in- charge. DSR Code 15.4 |
| 286 | Supply and laying of aluminium conductor PVC insulated armourd served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc (e) 6 sq. mm 3 core UPPWD 501 (e) |
| 287 | S/F high Tensile steel colour coated anti rust ,high temp resistant sheet with Tensile Strength 550 MPA hot dip metallic (zinc Aluminum Alloy (Zn-55%)(Al-45% ) Coating 70GSM with total thikness not less than 0.50mm (TCT) Durashine make with necessary over laps including S/F Galvanized J/V Hook according to purlin with ,nut,washer and bitumen washers etc.including cost of material ,labour T&P etc and special fastener (HT) , nuts & washer provide dia by the company etc required for proper completion of work as per direction of E/I confirming 1.5. 1397:1993. NSI Ref CSI No. 26.60 (20-21) |
| 288 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore. DSR 18.17.1 |
| 289 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :20 mm nominal bore. DSR 18.17.1A |
| 290 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :32 mm nominal bore. DSR 18.17.2 |
| 291 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :50 mm nominal bore. DSR 18.17.4 |
| 292 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :65 mm nominal bore. DSR 18.17.5 |
| 293 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :80 mm nominal bore. DSR 18.17.5 |
| 294 | Extraction of defective VT submersible pumps and motor with 60\\" x 90\\" column pipe and then lowering of the repaired pump and motor with pipe and testing the same including checking main cut-out fuse and operation of Tube well for 24 hours fo rits smooth working with all cost of materials,labour and T&P etc required for the proper completion of the work. NSI Ref CSI No. 20.28 (SOR 23-24) |
| 295 | Supply & replacing of electrical control panel of L&T / Havells or equivalent make for submersible pump / pumpset containing contractor relay condenser. (b) for 1.5/ 2 H.P pump set single phase NSI Ref CSI No. 19.31-b) (SOR 23-24) |
| 296 | Supply & Installation of submersible pump of K.S.B/ CALAMA. or eqt. make including cost of labour, T&P and material required for completion of work. b) 1.5 HP outlet 40mm dia. or more, Head 71/36, Discharge 2000/6000 LPH. NSI Ref CSI No. 19.32 (b) (SOR 23-24) |
| 297 | Supply & Installation of submersible pump of K.S.B/ CALAMA. or eqt. make including cost of labour, T&P and material required for completion of work. d) 3 HP outlet 50 mm dia. or more, Head 60/24, Discharge 6000/14000 LPH. NSI Ref CSI No. 19.32 (d) (SOR 23-24) |
| 298 | Supply & replacing of electrical control panel of L&T / Havells or equivalent make for submersible pump / pumpset containing contractor relay condenser. (c) for 3 H.P pump set single phase NSI Ref CSI No. 19.31-c) (SOR 23-24) |
| 299 | Earthing with G.I earth pipe 4.5 meter long, 40 mm dia including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc (but without charcoal/coke and salt) as required. DSR E&M (5.1) Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
| 5 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
