|
| 1 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinthlevel :1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) |
| 2 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
| 3 | Providing & Making & Fixing of BISON BOARD Both Side complete, as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge. |
| 4 | Dismanliting the old structure as per the dirrection and disposing of malvaspecification and direction as approved by Engineer -in-Charge. |
| 5 | Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.l. limpet washers filled with white lead, ,including including a a coat coat of of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces). excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. ever 1.00 mm thick with zinc coating not less than 275 gm/m² |
| 6 | Providing & Fixing of at all height false ceiling including providing and fixing of frame made of special section power pressed from m.s. sheet and galvonised in accordance with zinc coating of grade 350 as per IS 277 and consisting of angle cleat 25x1.6mm with flanges of 27mm and 37mm at 1200mm c/c one flanged fix to the ceiling with dash fastener 12.5mm dia and and 40mm long with 6mm dia bolt to the angle hangers of 25x25x0.55 mm of required lengthened other end of angle hanger being fixed with nut and bolts to GI channel 45x15x0.90mm running at the rate of 1200 mm c/c to with the ceiling section 0.5mm thick button wedges of 80mm with tappered flenges of 26 mm each having clips of 10.5mm.at 450mmc/ c shall be fixed in direction perpendicular to GI channels with connecting clips made out of 2.64MM diax230mm long GI wire at every junction including fixing the gypsum board with ceiling section and perimetre channels 0.50 mm thick 27mm high having flenges of 20mm and 30mm long ,perimeter of ceiling fixed to wall /partition with help of rawl plugs at 450mm c/c with 25 mm long drive all screws @230mm interval including jointing and fixing to a flush finish of tappered end sq edge of board with recommended filler jointing and tapper finisher and two coat of primer suitable for board as per manufacturers specification and also including the cost of making of openning for light fittings grills diffusers cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specification and direction of engineer incharge but excluding the cost of painting. 12.50mm thick tapered edge gypsum board. |
| 7 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm |
| 8 | Grouting the joints of flooring tiles having joints using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. |
| 9 | Providing & Making & Fixing of Commercial Wall Partition made with Aluminium Section of 2\\"x1\\" @ 2'CC frame work cladded with 9MM Ply on Both Side complete with painted or polishe. as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge. |
| 10 | Providing & Making & Fixing of Wall Panneling made with 1MM Laminate & 5.5MM MDF on Existing Surface complete with painted or polishe. as per the approved design all complete as per drawing, specification and direction as approved by Engineer -in-Charge. |
| 11 | Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer |
| 12 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 13 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm |
| 14 | Providing & Fixing of Photo Frames Having Size (600WX900HT) of Picture in Coloured Canvas Prints with wooden frame borders & Non Reflective glass complete as per desigh, drawings, specification & as approved by Architect/Engineer Incharge. |
| 15 | Providing & Fixing of Signages of 'TOURISM INFORMATION CENTER' back light all weather water proof Made of complete as per desigh, drawings, specification & as approved by Architect/Engineer Incharge. |
| 16 | Providing & fixing Toughned glass In Window with 12mm Modi float glass fixed edge to edge as per design and drawing and polished where required along with neccesary hardware all complete as per drawing, specification and direction of engineer incharge. |
| 17 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. Group A |
| 18 | Supply and fixing of Power point and Supply and fixing of power plug with 10 Amp./250 volt flush type modular switch and 5 pin 10A /250 volt flush type universal modular socket switch on concealed M.S. box including supply of all material, labour t&P etc. required for proper completion of work. |
| 19 | Supply and fixing of wire, Power point and Supply and fixing of power plug with 20 Amp./250 volt flush type modular switch and 5 pin 20 nA/250 volt flush typ[e universal modular socket switch on concealed M.S. box including supply of all material, labour t&P etc. required for proper completion of work. |
| 20 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 21 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 22 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 4.0 sq. mm + 1 X 4.0 sq. mm earth wire |
| 23 | Supplying & Drawing co-axial TV cable RG-6 grade, 0.7 mm. solid copper conductor, PE insulated] shielded with fine finned copper braid and protected with PVC sheath in the existing surface/ recessed steel/PVC conduit as required. For T.V. Socket outlet |
| 24 | Providing Drawing Connecting And Testing Of Enhanced Categoey 4 Pair Lan Local Area Network Cable 24 AWG Conductor Performance Specifide 5E U L and CUL Listed In Existing PVC Conduit .(CAT-6 Network Cable) |
| 25 | Supply & Fixing of following sizes of medium class PVC conduit alongwith accessories in sueface/recess including cutting the wall & making it good the same in case of recessed conduit as required. 20MM |
| 26 | Supply & Fixing of following sizes of medium class PVC conduit alongwith accessories in sueface/recess including cutting the wall & making it good the same in case of recessed conduit as required. 25MM |
| 27 | Supply & Fixing of following sizes of medium class PVC conduit alongwith accessories in sueface/recess including cutting the wall & making it good the same in case of recessed conduit as required. 32MM |
| 28 | Supplying & fixing of TV Antenna socket on Modular Plate & G.I Box including connections |
| 29 | Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required, 1 or 2 Module |
| 30 | Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required, 6 Module |
| 31 | Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required, 8 Module |
| 32 | Blank plate for modular plate type switch boards wherever required. |
| 33 | Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 34 | S&F of 2 pole Isolator in the db complete with connections, testing and commissioning etc. as required. |
| 35 | S & F surface/Flush mounting single phase TPN distribution board with additional metal door without MCB complete in all respect, as directed at site by Engineer in charge. CAT-A |
| 36 | Supply and fixing of recess mounting round 15 TO 18 Watt LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set complete in all respect. CAT-AAA |
| 37 | Supply and fixing of 400mm Wall Fan all complete as per drawing and specification and direction of engineer incharge. Make-Crompton/Bajaj/Havels Equivalent |
| 38 | Supply and Fixing of Deep Recess Mounting round 10 Watt COB LED Spot Light having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set complete in all respect. Make-Ledadvance/Ledos/Ledlum/Philips, Equivalent |
| 39 | Providing & Fixing of 2KVA OFF-LINE Solar power plant with inverter Having Battery Stand all complete as per drawing and specification and direction of engineer incharge. Make-Aeon |
| 40 | Supply and Wiring with 10 SQMm, 4 core 2Xfy Copper Xlpe Insulated Armoured Str Frls Cable 1.1Kv complete in all respect. |
| 41 | Providing & Fixing of GI Earthing all complete as per drawing and specification and direction of engineer incharge. |
| 42 | Providing & Fixing of Copper Earthing all complete as per drawing and specification and direction of engineer incharge. |
| 43 | Providing & Fixing of LINEAR WORKSTATIONS SIZE:- 1050W X 600D X 750HT AND 300HT HEIGHT Specifications: Table Top - 25mm thick Pre Lam particle board with 2mm edge lipping on all exposed sides. Support - MS powder coated diamond shape leg of 55X55mm size with die cast connectors and supporting MS cross beams. Main Screen:- Aluminum anodised 30mm scree n with fabric magnetic and glass marker tiles. Privacy Screen:- 6mm thick acrylic screen on studs. Wiremanagement - 450mm metal flip up with provision to mount switches and sockets on MS cable tray and vertical wire entry cover between the intermeidate leg for power and data. |
| 44 | Providing & Fixing of Mobile Pedestal made of 0.6mm thick CRCA with 1 drawer units and 1 filling folder unit. The Drawer units are made mobile with the use of castors. Fixed pedestal shall be provided with an overall size 400mm X 450mm X 640mm. The pedestal shall be made up of CRCA powder coated sheet. The pedestal shall have 2 nos. of drawer i.e. 1 box drawer and 1 filing drawer. The drawer shall be operated on sliding channels to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key, Make-Featherlite |
| 45 | Providing & Fixing, Medium Back chair Having Base: Nylon Base- The 640mm dia (26 inches) five pronged base is made out of GF nylon – Reinforced with bottom ribbing for additional buttress and strength. Tested prudently and confirming to ANSI/BIFMA X5.1-2011 General Purpose Office Chair Standards. The base shall be 67 cm pitch-center diameter -77 cm with castors. MS ring will be insert molded for better grip in the swaged taper. Castors: Twin Castors 50mm dia complying to ANSI / BIFMA X 5.1 – 2002. Castors will be made in PP. The axle pin will be rust protected- Zinc pacified. The pin should be designed to have push fit with lock ring. RoHS compliant castors. Gas lift: Standard Gas lift 100 mm stroke with pneumatic height adjustment as per the seat height criteria. - Class 4 as per ANSI BIFMA performance standards. Possibility to increase the seat height if required with Gas lift stroke- 110 -125 mm. Mechanism:Centre Tilt Mechanism: compact and stable with 8″ x 6″ mount holes as per European Standard. Initial seat angle of 3 degrees and full recline angle of 20 degrees for ergonomic comfort. Provided with common lever for locking and up/down adjustment and horizontal movement of the lever to engage and disengage lock at upright position Lever provided for rotational movement to operate gas lift and adjust chair height to user specification. Full length plastic knob provided to cover lever bar giving better aesthetical appeal to the mechanism. Knob provided to adjust spring tension to suit individual user in order to ensure maximum chair comfort. Arms:Fixed Arms Injected molded arms- polyurethane 20% GF nylon. The polypropylene arms will have steel inserts. The arm profile should blend with the back profile without gap. Seat: Seat Height- 450-540mm with hydraulic height adjustability of 90-100mm. Seat Width & Height- Size of the chair shall be -Back: 45.0cm. (w) x 59.0cm.(H) .Seat: 48.0cm (w) X 49.0cm.(D). Chair back should be connected to the Polyurethane arms for achieving comfortable seating posture.Effective back height from Seat - 560mm, Ply wood- 12 mm thick with 7 ply. Fire retardant type exterior grade phenol formaldehyde bonded. It will be hot pressed ply - conforming to I.S.I. 5509. The arm and back shall be fixed together to the seat with Allen bolts.The bolts will be screwed to the “T” nuts fixed to the plywood seat. Fabric: Upholstery: Seat & Back are duly upholstered with approved fabric. The back should have the option of mesh back AN-70 (black) and AN-75(grey). GSM for mesh 340. No flaming or progressive smolderingwithin one hour of placement of the cigarettes. Fire rated fabric confirming to BSEN 1021 and IS 15061-2012 Foam: Seat cushion with pre molded foam of 50 - 60 density in the shape of plywood. Density -- 52 kg/m3, Hardness -- 12.6kgf at 25%- Back cushion- density- 32g/sq in. Back:Mesh back on injected molded PP with 30% GF nylon. The back should have the option of mesh or fabric back. The mesh will be GSM 340 grade. . ALPHA MB, Make-Featherlite / Geeken / Hof / Ferris/ Equivalent |
| 46 | Providing & Fixing of Single Seater Sofa of Size: 850L X 790D X 790H Seat Foam: the sofa is made up of fine quality leatherette.The structure is made up of silver wood and pine wood.The Seat is made of PU Foam with Density 32 to 40 +/- 2 kg/cu .mtr Seat is upholstered wuth Leatherite.Back Foam: The Back is made of PU Foam with Density 32 to 40 +/- 2 kg/cu, Backis upholstered with Leatherite.Unterstructure is made up of silver wood or pine wood , 4mm Dia zigzag Spring is mounted in the understructure for support and additional cushioning purpose. Legs should be made up of stainless steel tubes/pipes, S-SERIES, Make-Featherlite/Geeken/Hof/Equivalent |
| 47 | Providing & Fixing of Corner Table of SIZE:- 550W X 550D X 400D Table top made out of stone Base/ Understructure:- Made up of MS and will be powder coated by Nano ceramic surface treatment process compiled to a Bend test-ASTM D3451 – 06, Adhesion -DIN EN 14901 Salt spray test- DIN EN ISO 9227, which is non-hazardous, environmental friendly and will have uniform powder coating thickness of 50-60-micron thickness, CT-867, Make-Featherlite/Geeken/Hof/Equivalent |
| 48 | Providing & Making & Fixing of Storage Cabinet made of 19mm board, having shelves & shutters & teak wood beading & finished surface of 1mm thick Laminate including all hardware like tower bolts, hinges, lock & handle as per approved drawing & direction of Engineer incharge. |
| 49 | Supply, Installation, testing and commissioning of wall mountable 55\\" high resolution LED monitor with HDMI port and commercial series suitable for 12x7 operation. All accessories for installation including wall mounting stand/ bracket. Make - SamsunG |
| 50 | Providing & Fixing of Cluster Stone Brick Stamping of Size (8.46\\"x2.36\\") & 13MM (Approx) Thick having Super Hard outer shell on Vertical Surface with uncoloured Adhesive FS complete as per desigh, drawings, specification & as approved by Architect/Engineer Incharge. |
| 51 | Providing & Fixing of Roller Blinds with Hand Rail of approved shade as per drawing & specification as approved by Engineer -in-Charge. |
| 52 | Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account).The weight of aluminium extruded section shall be taken for purpose of payment. |
| 53 | Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel (Making Louvers & Groves) Cladding, with open grooves for linear as well as curvilinear portions of the building, for all heights and all levels etc. including:Structural analysis & design and preparation of shop drawings for pressure equalization or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design ) Providing, fabricating and supplying and fixing panels of aluminum composite panel cladding in Pan shape of approved shades made out of 3mm thick aluminum composite panel material consisting of 2.40mm thick non toxic low density polyethylene virgin core sandwiched between two Aluminum coated sheets (each 0.3mm thick of AA 3105 Alloy grade). The aluminum composite panel cladding sheet shall be coil coated, with Kynar 500 based/hylar 5000 PVDF / Lumiflon based fluoropolymer resin lead 4.10 to 4.30 kg per sqm., nuts, bolts, washers, cleat drawings. |
| 54 | Providing & Applying white cement based putty of average thickness 1 mm of approved brand and manufacturer over plastered surface to prapare the surface even & smooth complete. |
| 55 | Finishing walls with textured exterior paint of required shade New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 |
| 56 | Providing and fixing of red/pink sand stone arches on all window opening as per aproved colour and design complete as per directions and approval of Engineer-in-charge . |
| 57 | Providing and fixing of red sand stone single piece arch with design as per aproved colour and design complete as per directions and approval of Engineer-in-charge . Please Enable Macros to View BoQ information |
