|
| 1 | Taking down cement plaster any description on brick or stone walls or wall tiles etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed. |
| 2 | Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed. |
| 3 | M&L Brick work using old size bricks with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed. |
| 4 | M&L for rendering 10mm thick in ceiling on brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement all as specified and directed. |
| 5 | M&L for rendering 10mm thick internal surfaces on fair faces of brick work or concrete in cm 1:6 as directed by Engr-in-charge. |
| 6 | M&L for rendering 15mm thick external surfaces on brick/concrete in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed. |
| 7 | M&L for Preparation of old decorated surfaces of walls and applying two coats of distempering complete all as specified and directed. |
| 8 | M&L preparing new/old plastered surfaces of wall/ceiling and applying complete wall with 1.0 mm Wall putty and making smooth surfaces and applying two coats of Oil bound distemper over a coat of primer all as specified and directed by Engineer-in-Charge. |
| 9 | Preparing new/old plastered surfaces and applying two coats of cement base paint on surfaces of walls over one coat of white wash complete all as specified and directed by engr in charge. |
| 10 | Dismantling stone slab of any description laid beddded & pointed ias specified and directed. |
| 11 | M&L for granite (any type) work (table rubbed and polished) 18 to 20 mm thick in working platform and like including cutting for sink etc. in 20mm thick cement mortar (1:4) including rounding of edges and pointing in white cement (1:2) using marble dust with admixture of pigment to match.complete all as specified and as directed |
| 12 | Demolition of Concrete in ground floors and pavings including floor tiles n exc 15 cm thickness (below or above ground level) complete all as specified and directed. |
| 13 | Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing), removing serviceable tiles to store and rubbish off the premises |
| 14 | M&L for 25 mm thick PCC 1:2:4 (20mm graded aggregate ) in levelling course of floor complete all as specified and directed. |
| 15 | M&L Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed be in C:M 1:4 complete etc. complete all as specified and directed by engr in charge. Notes : Shade of the tile including colour, design and pattern shall be approved by AGE. |
| 16 | S&F light shade non skid Ceramic tiles 7 to 8 mm thick(square/ rectangular) polished, area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed be in C:M 1:4 complete all as specified and directed by engr in charge complete all as specified and directed by engr in charge. Notes : Shade of the tile including colour, design and pattern shall be approved by AGE |
| 17 | S&F light shade non skid Ceramic tiles 7 to 8 mm thick(square/ rectangular) polished, area of each tiles not exceeding 0.38 sqm, in skirting set and jointed in neat cement slurry and pointed in white or coloured cement to including backing coat 10mm thick cement mortar in 1:4 complete all as specified and directed by engr in charge complete all as specified and directed by engr in charge. Notes : Shade of the tile including colour, design and pattern shall be approved by AGE |
| 18 | M&L for glazed ceramic coloured tiles in verticle surface 450mmx350mmx7-8mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over including backing coat 10mm thick cement mortar in 1:4 complete all as specified and directed by engr in charge. Notes : Shade of the tile including colour, design and pattern shall be approved by AGE. |
| 19 | M & L Machine cut Kota stone slab flooring 18-22mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing over and including screed bed or bedding layer of mortar 20 mm thick Cement Mortar 1:6 complete all as specified and directed. |
| 20 | Demolition of reinforced cement concrete in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed. |
| 21 | M & L for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. |
| 22 | Form work to sofit of suspended slabs such as roof slabs,landings & similar work not exc 200mm thick(Horizontal of sloping) rough finished surfaces of concrete flat complete all as specified & directed. |
| 23 | M & L for Precast cement concrete (1:2:4) type B1 using 20 mm graded stone aggregate as in landings, cover slab (for manholes , drain cover etc) and similar work including necessary form work and set in CM (1:6) complete all as specified and directed. Note :- Reinforcement shall be measured and paid separately. |
| 24 | M&L RCC type B-1, 1:2:4 (using 20 mm graded stone aggregate) in chajjas complete all as specified and directed. |
| 25 | M & L for TMT bars 8 mm dia & over cut to length, bent to shape required, including crancking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. |
| 26 | S & F for Formwork fair finished Falt surface to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed. |
| 27 | M&L for PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls of 110 mm bore of pipe etc complete all as specified and directed. |
| 28 | M&L for PVC (SWR) pipes single socketed, in any length with rubber ring joints,laid in trenches of 110 mm bore of pipe etc complete all as specified and directed. |
| 29 | M&L for PVC (SWR) pipes single socketed, in any length with rubber ring joints,fixed to walls of 75 mm bore of pipe etc complete all as specified and directed |
| 30 | M&L for PVC (SWR) pipes single socketed, in any length with rubber ring joints,laid in trenches of 75 mm bore of pipe etc complete all as specified and directed |
| 31 | S&F PVC (SWR) bends ISI marked any radius of 110 mm bore with access door complete all as specified and directed. |
| 32 | S&F PVC (SWR) bends ISI marked any radius of 75 mm bore with access door complete all as specified and directed. |
| 33 | S&F PVC (SWR) junction single, (single T) equal or un equal of 110 mm bore of pipe complete all as specified and directed |
| 34 | PVC (SWR) vent cowl for 110 mm bore pipe complete all as specified and directed. |
| 35 | PVC (SWR) multi floor trap with grating 75 mm dia including jointing with solvent cement complete all as specified and directed. |
| 36 | S & F of 600mm x 450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 37 | S&F in repair 15 mm dia bore bib taps, cast copper alloy chromium plated fancy type with crutch alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. |
| 38 | S&F in repair 15 mm dia bore pillar taps cast copper alloy, with capstan head, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' and 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed. |
| 39 | S&F in repair 15 mm dia stop valves/angle valves, cast copper alloy, fancy type chromium plated with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe complete all as specified and directed. |
| 40 | S & F in repair for Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 41 | S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed. |
| 42 | S & F sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed by engr in charge |
| 43 | S &F as in repair chromium plated Shower rose 15 mm size, 125mm long with arms complete all as specified and directed. |
| 44 | S&F vitreous china wash basin white flat back size 550 x 400mm including pedestal stand excluding taps, waste, chain & plug and porcelain stopper including brackets or fixed to walls with anchor fastners complete all as specified and directed by Engr-in-charge. |
| 45 | S & F in Repair of Vitreous China wash down water closet pan (pedestal pattern), white including fixing bolts, but excuding flushing cistern and flush pipe complete all as specified and directed by Engr-in-charge . |
| 46 | S & F in repairs of vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests but incuding flush pipe and connection to the flushing cistern complete all as specified and directed by Engr-in-charge. ( Note : Flusing cistern is paid seperately) |
| 47 | S & F of 10 litre PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed by Engr-in-charge |
| 48 | S&F in repair rotational three layer moulded polyethylene water storage tanks (cylinderical vertical with closed top) capacity 1000 Ltr hoisted and fixed in position all as specified and directed by Engr-in-charge. |
| 49 | S&F in repairs aluminium anodised Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed by Engr-in-charge . |
| 50 | Taking down chowkat or frame with shutter (without taking off shutters from the frames) area not exceeding 1.5 Sq mtr each complete all as specified and directed by Engr-in-charge |
| 51 | Taking down chowket or frame with shutter (without taking off shutters from the frames) area exceeding 1.5 Sq mtr but not exceeding 4 Sq mtr each |
| 52 | Taking down shutter but exc 1 sqm and n exc 2 sqm each complete all as specified and directed |
| 53 | Taking down re-fixing Shutters of any description but exc 1 sq. m and n exc 2 sq. m each in same opening including easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc. Renewal of builder's hardware articles, if specially ordered, shall be paid for at 'supplied only' rates. |
| 54 | M&L for 35mm thick second class hardwood glazed and skelton door shutters (Three panels) open rebated and prepared to receive glass / gauge etc edges of framing plain chamfered or rounded with cut and mitred beads for securing glass/gauges etc with sash bars size of members of shutter as specified in SSR Part-I section 8, clause 8.24 (a) complete all as specified and directed by Engr-in-charge |
| 55 | M&L for 30 mm thick Flush shutters, solid core construction, with block board core plywood face panels on both side, commercial type on both sides complete all as specified and directed by Engr-in-charge |
| 56 | S&F 125 mm long Stainless steel butt hinges with steel hinge pin etc complete all as specified and directed by Engr-in-charge. |
| 57 | S&F 200mm long aluminium anodised barrel tower bolt and fixed complete all as specified and directed by Engr-in-charge |
| 58 | S&F 150mm long aluminium anodised handle cast type and fixed D Type complete all as specified and directed by Engr-in-charge |
| 59 | S&F alluminum alloy, anodised, cast type or extruded section, sliding door bolt with hasp & staple (bolt type) with fixing clips and bolts and 300 mm long complete all as specified and directed by Engr-in-charge |
| 60 | S&F Mild steel 300mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engr-in-charge |
| 61 | S & F Powder coated aluminium frame/shutters for doors, windows, ventilators sliding/openable etc with joining cleat for fixing, locking arrangement, rubber beading, screws, etc including taking down and making the surface good complete all as specified and directedNote : (i) Glazing and wire mesh shall be measured and paid separetely. (ii) Item shall be paid as per weight of aluminium section (iii) The rate quoted shall be inclusive of the cost of neoprene beading, glazing pin, screws and powder coated fittings such as locking arraangement etc as required, which shall not be measured for arrivig the weight (iv) The rate shall also be inclusive of complete packing with silicon gel around contacting surfaces of aluminium work, and including matching the existing. |
| 62 | Supply only Galvanised steel wire cloth. 0.56 mm nominal dia of wire and average width of aperture 1.18mm complete all as specified and directed |
| 63 | Supply fix in repair Galvanised steel wire cloth. 0.56 mm nominal dia of wire and average width of aperture 1.18mm complete all as specified and directed |
| 64 | Supply only 4 mm thick Sheet glass, ordinary quality, in squares exc 0.5 sq. m each pane complete all as specified and directed |
| 65 | Supply and fixing Figured glass, pinhead type in squares n exc 0.5 sqm each pane complete all as specified and directed |
| 66 | Pressed steel frames of size 105x60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed |
| 67 | Pressed steel frames of size 125x60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc.complete all as specified and directed |
| 68 | S & F of Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed |
| 69 | M & L two coats of synthetic enamel painting on steel surfaces exc 10 cm width or girth over one coat of red oxide primer including preparation of new steel surfaces complete all as specified and directed |
| 70 | M & L two coats of synthetic enamel painting on steel surfaces exc 10 cm width or girth over one coat of red oxide primer including preparation of old steel surfaces complete all as specified and directed |
| 71 | M&L two coat of synthetic enamel paint over old wooden surfaces of any description not otherwise described over 10cm in width or grith over one coat of pink primer including preparation of surfaces complete all as specified and directed |
| 72 | M&L two coat of synthetic enamel paint over New wooden surfaces of any description not otherwise described over 10cm in width or grith over one coat of pink primer including preparation of surfaces complete all as specified and directed |
| 73 | Taking down of existing GI Tubing 15 mm dia complete all as specified and directed by engr in charge |
| 74 | Taking down of existing GI Tubing 20 mm dia complete all as specified and directed by engr in charge |
| 75 | Supplying and laying as in repair of CPVC pipes 16mm outer dia SDR 11 & Plain CPVC SDR 11 fittings on walls/floors complete all as specified and directed by Engr-in-charge. |
| 76 | Supplying and laying as in repair of CPVC pipes 20mm outer dia SDR 11 & Plain CPVC SDR 11 fittings on walls/floors complete all as specified and directed by Engr-in-charge. |
| 77 | S & F of CPVC pipes MBTA/FBTA fittings such as tee, elbow, socket and Tank union etc of 16 mm outer dia complete all as specified and directed by engr in charge |
| 78 | S & F as in repair of CPVC pipes MBTA/FBTA fittings such as tee, elbow and socket etc of 20mm outer dia complete all as specified and directed by engr in charge |
| 79 | Dismantling of wall and ceiling boards, any thickness including cover fillets complete all as specified and directed by engr in charge. |
| 80 | S & F of Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and directed by engr in charge. |
| 81 | S&F 4 mm thick HPSC (High Pressure steam cured) pre-primed textured designer board, water resistant, be placed in the grid system complete all as specified and directed by the Engineer-in-Charge. |
| 82 | S & F solid PVC frame of size 50 mm x 47 mm made out of 5 mm single side prelam PVC sheet & edges will be printed to match with prelam sheet reinforced with MS square tube etc complete all as specified and directed by Engr-in-charge |
| 83 | S&F factory made solid panel PVC door shutter 30mm (Style) consisting of frame made out of M.S tubes for top and bottom rails M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheets to be fitted in the M.S frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame complete all as specified and directed |
| 84 | S&F 100mm long butt hinges medium weight cold rolled mild steel and fixed complete all as specified and directed |
| 85 | S&F 150 mm long aluminium anodised barrel tower bolt and 12 mm dia fixed complete all as specified and directed |
| 86 | S&F 125mm long aluminium anodised handle cast type and fixed D Type complete all as specified and directed |
| 87 | M&L for 18 mm thick Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on both faces; fixed with screws to timber frame work complete. |
| 88 | M&L for 50 mm thick cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base of flooring/ hard standing & finished the surface even & fair complete all as specified and directed |
| 89 | M & L for 15mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes finished even and rough complete all as specified and directed |
| 90 | M&L for Chequered cement concrete tiles 30cm x 30cm x 25mm thick with grey cement and pigment set and jointed in neat cement slurry and pointed in white or coloured cement complete all as specified and directed |
| 91 | M & L for Precast cement concrete (1:2:4) type B1 using 20 mm graded stone aggregate as in landings, cover slab (for manholes , drain cover etc) and similar work including necessary form work and set in CM (1:6) complete all as specified and directed. Note :- Reinforcement shall be measured and paid separately. |
| 92 | M & L for providing cement concrete cas in situ 1:2:4, type B1 (using 20mm graded stone aggregate) in roof kerbs or mud stops, rounded or chamfered on edge including use of formwork complete all as specified and directed |
| 93 | M&L for Cement concrete 1:3:6 type C-1 (using 20 mm graded stone aggregate) 75 mm thick as in plinth protections, surface finished even and smooth w/o using extra cement including 3 mm thick glass dividing strip of figured glass , pin headed type, 38 mm wide inserted in position complete all as specified and directed |
| 94 | M&L for providing water proofing treatment over cleaned roof surfaces with super thermo APP modified water froofing membran comprssing of following for non-approachable roof:- (i) Removal of existing roof treatment and cleaning sweeping and washing and down with water to remove all dust etc from plastred roof surfaces/wall and filling of crack with sealing compound etc. (ii) Bitumen based primer conforming to IS 3384-1965 at 0.30 kg per sqm. (iii) One layer of super thermo APP modified water proofing membran with non polyster reinforcement of Make (M/S STP texsa Ltd/hyperplus membrane of M/S IWL India Ltd. M/S STP and Tikki Tar Ltd ) 3mm thick and minimum weight @ 3.50 Kg/sqm laid with gas torch and fasted on roof surfaces with roller. The over laps shall be sealed by flame including vertical surfaces after cutting necessary grooving and making good with PCC gola 1:2:4 type B1 etc adhere to bitumen all as per manufacturer instructions. (iv) Applying two coat of aluminium paint @ 0.20 kg/sqm per coat over bitumen layers as per manufacturer instruction (application including side lap overlaps shall be provided not less than 10cm and jointed sealed with torch as per manufacturer instruction specification. |
| 95 | Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing, etc. measured separately) |
| 96 | M&L Cutting into existing manholes 110mm dia for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specified and directed, |
| 97 | M&L cement concrete type E-2, 1:5:10(40 mm graded aggregate)lean concrete as in sunkun floor for filling etc. complete all as specified and directed. |
| 98 | M&L 40mm thick cement concrete type B-1, 1:2:4(20mm graded aggregate) as in sunkun floor complete all as specified and directed. |
| 99 | M&L 15mm thick plastering in CM 1:3 along the wall of toilet and bath mixed with 3 % WPC and finished even and smooth without using extra cement complete all as specified and directed. |
| 100 | Supplied only WPC |
| 101 | M&L bitumen blown any grade applied hot, two coats to concrete surfaces at the rate of 1.5 kg per sqm per coat complete all as specified and directed. |
| 102 | M&L Polythene film black 50 micron laid in floor complete all as specified and directed. |
| 103 | Dismantling of asbestos cement corrugated sheets as in roof coverings complete all as specified and directed. |
| 104 | Dismantling Framed timber scantlings 40 sq. cm and over in section, in any position complete all as specified and directed. |
| 105 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified. |
| 106 | S & F of Pre-painted galvalume aluminum zinc coating AZ-150 GI based tile profile galvalum sheet 0.50mm thick of red colour corrugated sheet as in roof covering/cladding to wall inlcuding cutting, moulding in shape fixed with self tapping screws as specified. |
| 107 | S & F of Pre-painted galvalume aluminum zinc coating AZ-150 GI based tile profile galvalum sheet 0.50mm thick of red colour plain sheet as in roof covering/cladding to wall inlcuding cutting, moulding in shape fixed with self tapping screws as specified. |
| 108 | S & F of Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc nd similar work conforming to Fe.290. Gde-E-165 complete all as directed & specified. |
| 109 | M & L for preparation of the old surfaces of walls including complete removal of the existing treatment and applying two coats of cement base paint all as specified and directed. |
| 110 | M & L for preparation of the old surfaces of walls and applying one coat of oil emulsion distemper complete all as specified and directed. |
| 111 | M & L for preparation of old painted wooden surfaces of any description, not otherwise described, over 10cm width or girth and applying two coat of synthetic enamel paint complete all as specified and directed. |
| 112 | M & L for preparation of old or previously untreated surfaces of any description, not otherwise describe, over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide complete all as specified and directed. |
| 113 | M&L for granite (any type) work (table rubbed and polished) 18 to 20 mm thick in working platform and like including cutting for sink etc. in 20mm thick cement mortar (1:4) including rounding of edges and pointing in white cement (1:2) using marble dust with admixture of pigment to match.complete all as specified and as directed |
| 114 | S&F ACP Sheet fixed 5mm to alm frame work as in door all as specified by Engr-in-Charge. Supply and laying river bed fine sand in trenches/ ducts 15 cm under cable and 8 cm above the cable for cushioning / protection to cable including spreading, levelling and get thick 18cm after hand punning complete all as specified and directed at site. Please Enable Macros to View BoQ information |
