|
| 1 | Dismantling of old B.O.E soling Disposal of refuse as including stacking by incharge up direction Asmper site incharge |
| 2 | Realying of bricks soiling Straight over burnt brick laid flat and dry including preparation of sub grade to prescribed camber and filling joint, with local earth spreading a blinding including all labour T&P as per SI.NO. 762a 2020 INTERLOCKING |
| 3 | Dismantling Brick work or stone work in lime or cement mortar and including stacking of dismolised material as directed by incharge up 60meter to 200 feet S.I.No-692 i/c |
| 4 | Dismantling cement concrete or brick or granolithic floor including base concretesurface includind sdisposalof all scrapped material for a distance of within 30m (100') distance as directed by the E/I. I/C Compaction in Layer by Road Roller S.I.No-697 i/c |
| 5 | Dismantling existing plaster including Disposal of refuse as including stacking by incharge up 60meter to 200 feet direction Asmper site incharge 2020 S.I.No-706 |
| 6 | Excavation cutting for roadway in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100 m, including trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections. |
| 7 | Disposal of waste material up to 3km |
| 8 | Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. |
| 9 | Cement concrente with cement, approved coarse sand and 40 mm brick ballast, in propotion 1:6:12including supply of all material, labour, T&P etc required for proper completion of work as per SI NO .273 |
| 10 | Class -150 Sub class' A' brick work in 1:4 with cement and approved fine sand of 1.25 F.M. mortor in foundation and upto plinth including supply of all materials, labour and T&P etc compelte as per SI NO .305 |
| 11 | Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401. (Grading-1 Material) |
| 12 | Providing and Laying of Interlocking Concrete Block Pavements having thickness 80 mm as per drawings and Technical Specification Clause 1504. As Per Analysis. |
| 13 | Providing and Laying of Interlocking Concrete Block Pavements having thickness 80 mm as per drawings and Technical Specification Clause 1504. As Per Analysis. |
| 14 | Mild steel or iron in plain work such of small size section such holding down bolt, hold fast tie rods gating ect. work wrought to required shape as necessary including with cutting bending for proper completion of the work fabrication of holes,door chaukhts and nosing. As per SI No-502 |
| 15 | Mild steel or iron in plain work such as in reinforced concreted or reinforced brick work wrought to required shape as necessary including with cutting bending for proper completion of the work including supply of steel its wastage.bend hooks & authorized overlapping shall be measured. As per SI No-504 |
| 16 | Finising walls( two coat) with plastic Emulsion paint of frist quality approved brand and manufacture on undecorated wall surface to give and even shade including throughly brushing the surface free frome morter dropping and other forgen matter and sand prepered smooth . I/C supply of all material labour T&P etc. required for proper complition to the work .(for kc drain wall) S.I. No-N.B.O.18.57 ch.15 |
| 17 | R.C.C Work with cement approved coarse sand & 20 mm guage approved stone grit in proportion of 1:1½:3 in T beam and slab roof and loumn including supply of all materials labour T & P etc. required for proper completion of the work. as per S.I.No.288b |
| 18 | 12mm thick plaster in wall in/out side in 1: 4 in cement f/sand mortar work SI 584 |
| 19 | Cemet concrete 1:2:4 plain C.C Floor with cement approved coarse sand and 20mm graded approved stone including supply of all materials labour T & P etc. required for proper completion of the work. as per S.I.No.279b |
| 20 | Providing and laying vitrified floor tiles of approve make and brand in difference size (thickness specified by manufacturer) with water absorption less than 0.8% and confirmig to IS 15622 of with 1:4 cement and approved coarse sand mortar finished with white cement slurry , jointiing and polishing complete, including supply of all materials, labour and T&P etc. reqired of proper of complection of the work.size of tiles 600x600mm As per SI NO CPWD 11.41.1 |
| 21 | Providing and laying rectified glazed ceremic floor tiles 300x300mm of approve make and brand in difference size (thickness specified by manufacturer) with water absorption less than 0.8% and confirmig to IS 15622 of with 1:4 cement and approved coarse sand mortar finished with white cement slurry , jointiing and polishing complete, including supply of all materials, labour and T&P etc. reqired of proper of complection of the work. As per SI NO CPWD 11.39 |
| 22 | Supply and fixing 6 mm china white glazed tiles in flooring or in skirting or dado laid with 1:3 cement and approved coarse sand mortar finished with white cement slurry , jointiing and polishing complete, including supply of all materials, labour and T&P etc. reqired of proper of complection of the work. As per SI NO 628. |
| 23 | Providing and fixing factory made uPVC white colour Casement window Three track three panels sliding window made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately.Area of window above 1.75 sqm) As per DSR-9.147D1.3 (Rate=11919x0.735=8761.09 Sqm each ) |
| 24 | Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineer- in-charge As per DSR-9.117.2 Extruded section profile size 42x50 mm(Rate=331.35x0.735=243.54 Rmt ) |
| 25 | 25 mm thick PVC flush door shutters made out of a one piece Multi chamber extruded PVC section of the size of 762 mm X 25 mm or less as per requirement with an average wall thickness of 1 mm (± 0.3 mm). PVC foam end cap of size 23x10 mm are provided on both vertical edges to ensure the overall thickness of 25 mm. M.S. tube having dimensions 19 mm x 19 mm and 1.0 mm (± 0.1 mm) is inserted along the hinge side of the door. Core of the door shutter should be filled with High Density Polyurethane foam. The Top & Bottom edges of the shutter are covered with an end-cap of the size 25 mm X 11 mm. Door shutter shall be reinforced with special polymeric reinforcements as per manufacturer’s specification and direction of Engineer-in-charge to take up necessary hardware and fixtures. Stickers indicating the locations of hardwarewill be pasted at appropriate places As per DSR-9.118.3 (Rate=3068.85x0.735=2255.60 Sqm ) |
| 26 | (ACP work) Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as Per DSR-25.2 curvilinear portions of the building for all heights and all levels, including: (a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc. |
| 27 | Supply and fixing of PVC pipe 110 mm dia ISI mark for drainage SI no.23(31) SOR 2020 p.no. 10 Rate=225x1.1=247.50 per rmt |
| 28 | Supply and informatory M.S. sign Board size 1.2x0.90meter made of 18mm gauge M.S sheet fic ISA 40x40x6mm from support in back side by 40x5mm flat iron on all four side along with to vertical post of 2.90mtr Diagonal bracing of size 40x5mm flat iron electrically welded and painted with one coat red oxide primer and 2coat superier quality enamel paint with lettering work of required specified information also L/c fixing in trech both side C.C 1:2:4 size 0.45x0.45x0.50m Required for proper complation of work reference specification S.I No. 502 |
| 29 | providing and fixing vitreous china extended wall mounting water closet of size 780x370x690mm of approved shape including providing &fixing white vitreous china cistern with dual flush fitting of flusing capacity 3 ltr 6ltr (adjustable to 4liter/8liter),including seat cover and cistern fitings,nuts, bolts and gasket etc.complete as per DSR-17.78 (Rate-14999.15) |
| 30 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x26Dx350 mim and 340x410x265 mm size respectively with automatic flushing cistern with standard flush pipe and C,P, brass spreaders with brass unions and G.I. clamps complete, lndluding painting of fittings and brackets, cutting and making good the walls and floors wherever required: One urinal basin with 5 litre white P.V.C. automatic flushing cistern. as per DSR-17.4.1(Rate-6258.75) |
| 31 | Provinding and fixing white vitreous china wash basin 550X400mm with 15 mm C.P. brass pillar tap DSR-17.7.3(Rate-2301.75) |
| 32 | 17.31 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.DSR-17.31(Rate-1607.95) |
| 33 | Providing and fixing of CPVC pipe having thermal stability of hot and cold water supply i/c fixing the pipe with clamp at 1 mt spacing and jointing the pipe with CVC solvent trenching refilling and testing of the joint.(External work) DSR-18.9.1 (Rate-244.7) |
| 34 | 15mm dai |
| 35 | Providing and fixing of 15mm CPVC outer dia pipe for concealed work complete with all. fittings and clamps, including cutting and making good the walls etc. Internal work including CPVC plain and brass threaded fittings as per detailed specification DSR-18.8 |
| 36 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete: DSR-18.18 |
| 37 | 15 mm nominal bore -18.18.1 |
| 38 | Providing and fixing C.P. brass bib cock of approved quality long body heavy quality L & K Jaguar or equivalent conforming to IS:8931.l |
| 39 | 15 mm nominal bore DSR-18.49 |
| 40 | Providing and fixing C.P. brass stop cock 400 gm (concealed) of standard design and of approved make conforming to IS:8931. |
| 41 | 15 mm nominal bore DSR-18.52 |
| 42 | Providing and fixing C.P. brass Angle valve for Basin in Mixture and Geyser of standard design and of approved make conforming to IS:8931. |
| 43 | 15 mm nominal bore DSR-18.53 |
| 44 | Providing and placing on terrace polyethylene water storage tank IS 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and oveerflow pipe but without fitting and base support. DSR-18.48 |
| 45 | Supply of full way gate Valve with CI wheel. |
| 46 | DSR-18.17 (15 mm Dia) |
| 47 | 12.41 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110mm dia pvc pipe DSR-12.41.2 |
| 48 | Point wiring in PVC conduit, with piano type switch :- Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class pvc conduit, with mdular type switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 49 | Group A |
| 50 | Power plug wiring in PVC conduit (2 x 4 Sq.Mm.) :- |
| 51 | Power plug wiring in PVC conduit (2 x 4 Sq.Mm.) :-Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class pvc conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. DSR 1.12 |
| 52 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class pvc conduit as required.2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire. DSR 1.14.2 |
| 53 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class pvc conduit as required.2 x 6 sq.mm. + 1 x 6 sq.mm. Earth wire DSR 1.14.4 |
| 54 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class pvc conduit as required.2 x 10 sq.mm. + 1 x 6 sq.mm. Earth wire DSR 1.14.5 |
| 55 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class pvc conduit as required.2 x 16 sq.mm. + 1 x 6 sq.mm. Earth wire DSR 1.14..6 |
| 56 | S/F power plug point piano type accessories :-Supplying and fixing metal box of 180 mm X 100 mm X 60 mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 6 pin 5/6 A & 15/16 A socket outlet and 15/16 A piano type switch, connections, painting etc. as required. DSR 1.30 |
| 57 | Supplying and fixing 5 amps. to 32 amps. rating, 240 volts `C' series, miniature circuit breaker (MCB)suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 58 | single pole |
| 59 | Supplying & fixing single pole, blanking plate in the existing MCB DB complete etc. as required. |
| 60 | S/F DP MCB IsolatorSupplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. DSR 2.12 |
| 61 | 63 Amps |
| 62 | Supplying and fixing following way, SP&N, sheet steel, MCB distribution board, 240 V on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB / RCCB / Isolator) |
| 63 | 8 way, Double door |
| 64 | 12 way, Double door For Main DB |
| 65 | Installation, testing and commissioning of fan including wiring the down rod of standard length (upto 30 cm.) with 1.5 sq. mm. FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required. DSR 1.45 |
| 66 | Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required DSR 1.50Upto 300 mm sweep DSR 1.50.1 Please Enable Macros to View BoQ information |
