|
| 1 | BUILDING WORKS (B) DISMANTLING, CUTTING CHASE, HOLES ETC 10. Stripping off worn out plaster and raking out joints of walls, celings etc. upto any height and in any floor including removing rubbish within a lead of 75m as directed. |
| 2 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface](ii) With 1:4 cement mortar (a) 20 mm thick plaster |
| 3 | Rendering the surface of walls and ceiling with white cement based wall putty of approved make and brand(1.5mm thick) |
| 4 | Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. (This item is applicable to new work or old work when the original surface has been exposed by removal of old paint.) |
| 5 | Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary :(a) On timber or plastered surface :With super gloss (hi-gloss) -(iv) Two coats (with any shade except white) |
| 6 | Supplying and laying true to line and level Anti-Skid, Full Body, Homogeneous & Granular finish Vitrified Tiles conforming to IS:15622-2006 & IS 4457-2007 andtesting shall be made in accordance with IS:13630 [Non- modular sizes for tiles with Skid resistance > 0.5, Mohr's hardness > 5.0, Staining resistance: Class-1, Water Absorption: E < 0.5%], MOR > 35N/sq.mm in Internal area of building e.g. Toilet Block, Passage, Corridor, Accessible Open Terrace etc. set in 20 mm sand cement mortar (1:4) and 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg./Sqm or using Polymerised Adhesive (6 mm thick layer applied directly over finished artificial stone floor/ Mosaic etc without any backing course) laid after application slurry using 1.75 Kg of cement per Sqm below mortar only, joints grouted with admixture of white cement and colouring pigment to match with colour of tiles/ epoxy grout materials of approved make as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials, labour and all other incidental charges complete true to the manufacturer's specification and direction of Engineer-in-Charge. (White cement, synthetic adhesive and grout material to be supplied by the contractor). a) In Ground Floor: Sizes-300 mm x300mm x10 mm with breaking strength > 1200 N |
| 7 | Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles includingroughening of concrete surface, if necessary or by synthetic adhesive& grout materials etc. (A) Floor With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @0.20kg/Sq.m. (b) Area of each tile above 0.09 Sq.m (i) Coloured decorative. Note: 2. Add extra for each addl, floor over the rate for item 35 & 36 of subhead A. (i) upto 4 th floor-Rs 5/ Sq.m (i) above 4 th floor-Rs 6.25/ Sq.m |
| 8 | Removal of rubbish,earth etc. from the working site and disposal of the same beyond the compound, in conformity with the Municipal / Corporation Rules for such disposal, loading into truck and cleaning the site in all respect as per direction of Engineer in CHARGE |
| 9 | Supplying, fitting and fixing best quality Indian make mirror 5.5 mm thick with silvering as per I.S.I. specifications supported on fibre glass frame of any colour, frame size 550 mm X 400 mm. |
| 10 | Supplying, fitting and fixing bathroom shelf of approved make of size 580 mm X 150 mm (porcelain).N.B. For coloured sanitary wares rates will be enhanced over the rates of corresponding items of white glazed sanitary wares as follows:(b) Roman brown, Fern green, Misty lilac, Orange, Sienna gold, Sepia,Silver grey, Alpine, Cornil, Sorvinto Blue by 100% |
| 11 | Supplying, fitting and fixing liquid soap container.(a) Cromium plated. |
| 12 | Chromium plated Bib Cock with wall flange (Equivalent to Code No. 5047 & Model - Florentine of Jaquar or similar brand). (Note: Item 7c(i), (ii) & 7d (i), (ii) to be done as per specific direction of the Superintending Engineer.) |
| 13 | Supplying, fitting and fixing pedestal of approved make for wash basin (white |
| 14 | Supplying, fitting and fixing soap holder.(a) PTMT (Prayag or equivalent) |
| 15 | Supplying, fitting and fixing Anglo-Indian W.C. in white glazed vitreous china ware of approved make complete in position with necessary bolts, nuts etc.(b)With 'S' trap (with vent)..N.B. For W.C. with trap without vent the rate will be reduced by Rs.25.00 |
| 16 | Supplying, fitting and fixing G.I. pipes of TATA make with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting withapproved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately) (A) For Exposed Work (f) (i) 50 mm dia. light quality |
| 17 | Supplying, Fitting & Fixing 30 mm thick bothside prelaminated Factory made solid Panel PVC Door Shutter consisting of outer frame made out of M.S. tubes of 19 gauge thickness and size 19 mmx19 mm for styles, top and bottom rails, M.S. frame shall have cost of steel primers of approved make and manufacture, M.S. frame covered with 5 mm th. heat moulded PVC ?C? channel of size 30 mm th, 70mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on either sidesforming styles; and 5 mm th. 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm tapered in 45 degree on the inner side to form top & bottom rail and 115 mm wide PVC sheet out of which 75mm shall be flatand 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided either side of thepanel with 10 mm (5mmx2) th.,20 mm wide cross PVC sheet as gap insert for top rail and bottom rail sheet to be fitted in the M.S. frame welded/sealed to the styles &rails with 7 mm (5mm+2 mm) th.x15 mmwide PVC sheet beading on inner side and joined together with solvent cement adhesive. An additional 5 mm th. PVC strip of 20 mm which is to be stuck on the interior side of the ?C? channel using PVCsolvent adhesive etc. complete excluding all necessary hardwares as per direction of Engineer-in- Charge. (For upper floors refer to item H(4) for items 16, 17, 18 & 19 under sub-head B ) |
| 18 | Supplying and fixing PVC casing-capping [Precision Make] on wall or ceiling, incl. necy. PVC fittings etc. and mending good damages to building works 25x10mm Size |
| 19 | Wiring With PVC Insulated & Unsheathed Single Core Stranded Copper Wire `'FR' ... in PVC Casing-Capping (Precision Make) on wall/ceiling.Wiring in 1.1 KV grade single core stranded 'FR' PVC insulated & unsheathed copper wire (Brand(approved by EIC) of following sizes in 25mm PVC casing-capping (Precision make) incl. necy. PVC clips, fittings etc. 2 x 22/0.3 (1.5 sqmm) |
| 20 | Wiring With PVC Insulated & Unsheathed Single Core Stranded Copper Wire `'FR' ... in PVC Casing-Capping (Precision Make) on wall/ceiling.Wiring in 1.1 KV grade single core stranded 'FR' PVC insulated & unsheathed copper wire (Brand(approved by EIC) of following sizes in 25mm PVC casing-capping (Precision make) incl. necy. PVC clips, fittings etc. 2 x 56/0.3 (4 sqmm) + 1 x 22/0.3 (1.5 sqmm) |
| 21 | Wiring With PVC Insulated & Unsheathed Single Core Stranded Copper Wire `'FR' ... in PVC Casing-Capping (Precision Make) on wall/ceiling.Wiring in 1.1 KV grade single core stranded 'FR' PVC insulated & unsheathed copper wire (Brand(approved by EIC) of following sizes in 25mm PVC casing-capping (Precision make) incl. necy. PVC clips, fittings etc. 2 x 36/0.3 (2.5 sqmm) + 1 x 22/0.3 (1.5 |
| 22 | Supply & Fixing 240 V, 3 nos. 16 A, 3 pin Modular type plug socket with 3 nos. 16A Modular type switch brand(approved by EIC), 20A Modular switch type SP MCB(c-curve) and Indicator without plug top on 2 row 12 Module GI Modular type switch board with 2 row 12 Module top cover plate flushed in wall incl. S&F switch board and cover plate and making necy. connections with PVC Cu wire and earth continuity wire etc. |
| 23 | Supplying & Fixing GI Modular Switch Board of the following sizes complete with three no. suitable size Copper bar with holes FOR Ph, N & E) fixed on bakelite/Hard Rubber insulator over the MS welded chairs incl. top cover flushed in wall FOR housing the board after cutting the brick wall incl. making earthing attachment, painting and mending good damages to building works 12 Module |
| 24 | Supplying & Fixing GI Modular Switch Board of the following sizes complete with three no. suitable size Copper bar with holes FOR Ph, N & E) fixed on bakelite/Hard Rubber insulator over the MS welded chairs incl. top cover flushed in wall FOR housing the board after cutting the brick wall incl. making earthing attachment, painting and mending good damages to building works 4 Module |
| 25 | Supply & Fixing 240 V 6 A Modular type switch brand approved by EIC) on existing GI Modular type switch board having top cover plate and making necessary connections as required |
| 26 | Fittings :Supply & Fixing angular batten holder (Anchor) on 75mm dia PVC round block / round bakelite on wall/ceiling |
| 27 | Supply & Fixing 240V, Modular Socket (2) Module) type fan regulator (Step type) brand(approved by EIC) on existing Modular GI switch board with top cover plate incl. making necy. connections etc. |
| 28 | SUPPLY AND FIXING OF PHILIPS SMARTBRITE XTRA 4 FT RUN LENGTH LED BATTEN TUBE LIGHT ,INCL FIXING ONLYFLUORESCENT LIGHT FITTING SUSPENDED 25 CM BELLOW THE CEILING WITH 2 NO . 20MM DIA EI CONDUIT (14 SWG ) SUPPORTS INCL.S&F EI CONDUIT , BALL SOKET/ SOKET TYPE CELLING PLATE AND CONNECTING THE LENGTH OF PVC INSULATED WIRE AND PAINTING ETC. AS REQUIRED BY 2*24/0.20 MM (1.5 SQMM) FLEXIBLE COPPER WIRE OF 1.10MT.LENGTH. MAKE: CROMPTON, 18W ITEM NO-5.3F.4.0.2 |
| 29 | SUPPLYING OF APPROVED MAKE EXHAUST FAN HEAVY DUTY WITH MOUNTING FRAME, BLADES AC230-250,300MM SWEEP RPM 900/1400(12??) |
| 30 | SUPPLY AND FIXING OF PHILIPS SURFACE DOWNLIGHT ,16 WATT WH , AFTER CUTTING OR WALL AS REQD. AND ALSO MENDING GOOD THE DAMAGES TO BUILDING WORK INCL WIRING ANS CONNECTION OF THE LIGHT 1.5 SQ MM CU WIRE COMPLET.MAKE -COMPTON 18 WATT SQUARE/ROUND |
| 31 | SUPPLY OF DIFFERENT TYPES OF LED LAMPS (9W) MAKE:PHILIPS 9.0 WATT , BASE B22/E27,825 |
| 32 | Fittings :Supplying & Fixing 240 V AC/DC superior type Multitune(min10 nos. tune)Call Bell (Anchor) with selector switch FOR single/Multi Tunes mode, Battery operated on HW board incl. S&F HW board |
| 33 | Sub Total |
| 34 | GST 9% |
| 35 | GST 9% |
| 36 | CESS 1% Please Enable Macros to View BoQ information |
