Tender For Special Repair To Bldg No 20 Parvati Villa (Rcc Roof) And Provn Of Toilet Cum Bathroom And Paved Pathway At Bldg No 7 Pwd Under Ge South Pune, Pune-Maharashtra

TDR : 55596012

Tender Notice
BOQ

19 Days Left

Pune , Maharashtra

Tender Brief : Tender For special Repair To Bldg No 20 Parvati Villa (Rcc Roof) And Provn Of Toilet Cum Bathroom And Paved Pathway At Bldg No 7 Pwd Under Ge South Pune

Document Fees
₹ 500 /-

EMD
₹ 67660.0 /-

Tender Value
₹ 33.83 Lakhs /-

Submission Date
10-06-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Removing of existing old bitumenous tarfelt (water proofing treatment) including cement screed bed , concrete padding and clean the surface with wire brush and washing with water to achieve the original surface of slab and M & L for water proofing treatment to RCC roof slab, walls, chajjas etc, shall be carried out as specified below and as directed by Engr-in-charge(a) M & L for 10 mm thick plaster screed bed layer in CM 1:3 on concrete surfaces (b) Preparing plastered surfaces of roof slab, walls, chajjas etc, by brooming with broom sweeping free from dirt dust etc and evenly applying a coat of approved bituminous primer @ 0.20 Kg/Sqm of area complete all as specified. (c) Laying APP polymer modified approved membrane, non woven, polyster, weighing not less than 3.5 Kg/Sqm and 3 mm thick with laps and overlaps as specified and joints sealed and applied complete by torch application method all as specified and directed by Engr-in-charge, Carrying out test by flooding water for 24 hrs for leakage and seepage and rectifying the same to the entire satisfaction of GE. (d) Finally applying a coat of solar reflective bituminous aluminium paint @ 0.15 ltr/Sqm on the top of membrane surfaces complete all as specified and as directed by Engr-in-charge. Note :- i) Rate includes disconnecting existing water tanks on roof slab of any capacity and refixing the same with necessary fittings after water proofing treatment. ii) Contractor should arrange alternate water supply to the accn till complete the water treatment work.
2	Demolition of reinforced cement concrete of any description and in any position complete
3	M&L for coloured glazed ceramic designed tiles in vertical surface 600x 300x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 10mm thick plaster in CM 1:4 incl dismantling floor, hearth or wall tiling including taking down cement plaster, removing serviceable tiles to store and rubbish off the premises complete all as speicified and directed.
4	M&L for Glazed ceramic tiles in vertical surface 300x 200x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 10mm thick plaster in CM 1:4 incl dismantling floor, hearth or wall tiling including taking down cement plaster, removing serviceable tiles to store and rubbish off the premises complete all as speicified and directed.
5	M&L for non skid ceramic colored tiles 7 to 8mm thick (square / rectangular), area of each tile exceeding 0.06 sqm but notexceeding 0.11 Sqm as in floor etc. set and jointed in neat cement slurry & pointed in white or coloured cement to match laid over and including 15mm thick screed bed in CM 1:6, incl dismantling floor, hearth , removing serviceable tiles to store and rubbish off the premises complete all as speicified and directed.
6	M&L for non skid ceramic colored tiles 7 to 8mm thick (square / rectangular), area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in floor etc. set and jointed in neat cement slurry & pointed in white or coloured cement to match laid over and including 15mm thick screed bed in CM 1:6, incl dismantling floor, hearth, removing serviceable tiles to store and rubbish off the premises complete all as speicified and directed.
7	M&L for non skid ceramic colored tiles 7 to 8mm thick (square / rectangular), area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in skiriting etc. set and jointed in neat cement slurry & pointed in white or coloured cement to match laid over 10mm thick plaster in CM 1:4 incl dismantling floor, hearth or wall tiling including taking down cement plaster, removing serviceable tiles to store and rubbish off the premises
8	M & L ( light shade) Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6 incl dismantling floor, hearth, removing serviceable tiles to store and rubbish off the premises complete all as speicified and directed.all as specified
9	M & L ( light shade) Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in skirting etc. set and jointed in neat cement slurry & pointed in white or coloured cement to match laid over 10mm thick plaster in CM 1:4 incl dismantling floor, hearth or wall tiling including taking down cement plaster, removing serviceable tiles to store and rubbish off the premises complete all as speicified and directed.all as specified
10	M & L granite ( of any type ) work ( table rubbed and polished ) 18 to 20 mm thick in steps, jambs, pillars, window cill , cooking platform and flooring in CM 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite with and including screed bed or bedding layer 15 mm thick, in CM 1:6 on stone /brick masonry / concrete surfaces including dismantling of stone slabs and rubbish off the premises complete all as speicified and directed.
11	Rounding edges of stone slab one edge, such as in steps, cooking platform and other similar situation complete all as specified and directed.
12	M & L cutting grooves on stone slabs such as in steps and other similar situations complete all as specified and directed
13	M & L Machine cut cuddapa stone slabs one side polished 20 to 25mm thick set and jointed in neat cement slurry and pointed in coloured cement to match laid over and including 20mm screed bed in cement mortar (1:6) including dismantling of stone slabs and rubbish off the premises complete all as speicified and directed.all as specified
14	S&F GI tubing tubes \\"medium grade\\" galvanized with all fittings and fixed complete to walls and ceiling or laid in floors etc including taking up or down carefully steel tubing and connections complete all as specified and directed of the following sizes :-
15	(a) 15mm bore
16	(b) 20mm bore
17	(c) 25 mm bore
18	S&F in repairs Gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified & directed of following bore of pipe :-
19	(a) 15mm bore
20	(b) 20mm bore
21	(b) 25 mm bore
22	Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades,shelves , lintels, etc.and cutting chases for concealed water tubing and making good, cutting not exc 10 cm girth in brick walls.
23	S&F in repair vitreous china wash hand basin, white, 550x 400mm flat back including providing CI brackets, PVC waste pipe 32mm dia, waste coupling 32mm bore of CP incl 15mm bore CP fancy type pillar cock etc all as specified and directed.
24	S&F in repairs vitreous china wash down water closet pan, 'Pedestal' pattern coloured, including fixing bolts etc including PVC seat cover white with flat bottom including MS, CP or aluminium anodised hinges devices incl 10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, including flush pipe 32 mm dia.complete all as specified and directed.
25	S & F in repairs vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor including trap set in and including concrete complete all as specified and directed.
26	S & F in repairs 10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, including flush pipe 32 mm dia. complete all as specified and directed.
27	S&F in repairs 15mm bore bib taps, brass chromium plated, cast copper alloy fancy type handle screwed down, screwed for iron pipes all as specified .
28	S & F in repairs 15 mm chromium plated 2 way bib cock fancy type with wall flange complete all as specified and directed.
29	S & F in repairs 15 mm stop valves / angular stop cock, fancy type cast copper alloy chromium plated with crutch or butterfly handle, screwed down and screwed both ends for iron pipe or for union complete all as specified and directed.
30	Ditto all as per item no 23 but consealed long shank
31	S&F in repairs CP Wall mixer 3-in-1 for mixing hot & cold water screwed down for iron pipe and fixed for 15mm bore of pipe complete all as specified and directed.
32	S & F in repairs 125 mm dia brass chromium plated shower rose including shower arm of approved quality complete.
33	S & F in repairs CP health faucet (ABS Body) with 1 mtr long flexible cod complete.
34	S & F in repairs 15 mm bore, 600 mm long PVC connections with PTMT nuts complete fixed to iron pipe at both ends complete all as specified and directed.
35	S & F in repairs brass chromium plated Tubular towel rail 20mm dia \\"D\\" type 60cm long.
36	S & F in repairs Toilet paper holder with flat recessed type stainless steel Complete all as specified and directed
37	S & F in repairs chromium plated soap dish fixed to plugs with chromium plated brass screws .
38	S & F Towel Ring of CP fixed with and including Chromium plated brass screws fixed in repairs.
39	S & F in repairs 600mm X 450mm X 5.5mm thick bevelled edge mirror of selected quality glass mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers with aluminium beading all around .
40	S& F in repair 5mm thick sheet glass corner shelf, 250mm radius including CP railing and CP brackets, complete all as speicified and directed.
41	S& F 75 mm dia PVC (SWR) floor trap, plain with stainless steel grating including jointing with solvent cement complete all as speicified and directed.
42	S& F 32 mm dia Low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sq. cm complete all as speicified and directed.
43	S & F Rotational moulded polyethylene water storage tanks ISI marked double layer of capacity 500 Litre (cylindrical vertical with closed top) hoisted and fixed in position incl all necesarry GI fittings including dismantling of existing water tank complete all as specified and directed.
44	S & F Rotational moulded polyethylene water storage tanks ISI marked double layer of capacity 1000 Litre (cylindrical vertical with closed top) hoisted and fixed in position incl all necesarry GI fittings including dismantling of existing water tank complete all as specified and directed.
45	S & F in repair ball valves high pressure of PTMT with epoxy coated, aluminium rod & high density plastic ball complete screwed for iron pipe or brass ferrule 20 mm bore complete.
46	S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including taking down existing pipe complete all as speicified and directed.Note :- Rate quoted shall deemed to be inclusive of necessary scaffolding / security measures as the work is to be carried out for elevated height upto 12 mtr height building.
47	S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall,including taking down existing pipe complete all as speicified and directed.Note :- Rate quoted shall deemed to be inclusive of necessary scaffolding / security measures as the work is to be carried out for elevated height upto 12 mtr height building.
48	S&F 110mm bore PVC (SWR) bends / Tee with acess door, complete all as speicified and directed.
49	S&F 75mm bore PVC (SWR) bends / Tee with acess door, complete all as speicified and directed.
50	Taking down shutters of any description exc 1.0 sqm but n.exc 2.00 Sqm each and rescuring or easing & adjusting after repair in door opening and connected carpentry work and refixing at same opening complete all as all specified.
51	Taking down shutters of any description exc 1.0 sqm and n exc 2 sqmtr complete all as specified & as directed
52	Taking down chowkhat /frame of door /window/ ventilators with shutter (without taking off shutter from the frame ) area not exc 1.5 Sqm a each complete all as specified
53	Taking down chowkat or frame with shutters (without taking of shutters from the frame) exc 1.5 Sqm but not exc 4 sqm each complete all as specified and as directed.
54	S & F pressed steel frames of size 105mm X 60 mm for doors with one or more rebates including necessary lugs, hinges, lock strikes plate, incl M & L for providing PCC type B-0 ,1:2:4(using 12.5 mm graded stone aggregate) to fill up the hollow portion of the frame complete all as specified and directed.
55	S & F pressed steel frames of size 125mm X 60mm for doors with one or more rebates including necessary lugs, hinges, lock strikes plate, incl M & L for providing PCC type B-0, 1:2:4 (using 12.5 mm graded stone aggregate) to fill up the hollow portion of the frame complete all as specified and directed.
56	S&F 35 mm thick factory made 2nd class hardwood gauged and skelton shutters open rebated and prepared to receive glass / gauze etc ( without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitered beads for securing glass etc size of members of shutters as specified in SSR part-I Section 8 cluse 8.24(a) and Fitted to chowkats complete all as specified and as directed.
57	S&F 35 mm thick factory made 2nd class hardwood plain framed panelled shutters/ any number member of panels) with panels of timber flat on both sides of wood particle board with commercial face veeners. The size of rail and stile as per IS : 1003 (Part I ) kiln seasoned and chemically pressure treated all as specified and as directed.
58	S & F 30 mm thick II nd class hard wood ,Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of sash bars and framing moulded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats
59	S & F 5 mm thick Figured glass, pinhead type in squares each pane complete all as specified and directed.
60	S & F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube and fixing in opening incl taking down of chowkat with shutter without taking off shutters from the frame including making good the distrubed surface complete all as specified and directed.
61	S & F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails .M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail ,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/scaled to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement and fixing in the frame as per manufacturers instructions and as directed by Engineer-in-Charge.
62	Supply and fix 100mm size of butt hinges, medium weight cold rolled mild steel complete all as specified and as directed.
63	Supply & fix aluminium anodised sliding door bolts 300 mm size with hasp, staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified.
64	Supply and fix 150mm size extruded aluminium alloy tower bolt fabricated type anodised complete all as specified.
65	Supply and fix 150mm size extruded aluminium alloy handles fabricated type anodised complete all as specified.
66	S&F 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed.
67	S &F in repairs aluminium powder coated fancy type bracket suitable for 20 mm bore curtain rod complete all as specified
68	S &F in repairs 20 mm bore aluminium powder coated curtain rod complete all as specified and as directed.
69	S&F stainless steel wire cloth.0.36mm nominal dia of wire and average width of aperture1.40mm and fixed with stainless steel wire staples to steel or wooden windows/door/shutters/frames etc. complete all as specified and as directed.
70	S&F in repairs, stainless steel plate rack of size 36inch x 39 inch x 10inch, made out of 0.63mm thick stainless steel sheet (Grade AISI 304 18/8), S S screws and round pipe, fixed to wall with screws complete all as specified and as directed.
71	S & F in repairs 18 mm thk PVC sheet shutter one side prelim of any shade as in cupboard or kitchen cabinet etc complete all as specified.
72	S & F Continuous (piano) hinges 30 mm width of flap,mild steel, bright finish or electrogalvanised complete all as specified and as directed.
73	S & F Magnetic door catches for cupboard/cabinet etc complete all as specified and as directed.
74	S&F 100mm dia Brass handles, cast type, polished bright cupboard handles fixed with nuts screws and washer complete all as specified and directed.
75	S&F three track sliding window with two or more shutter with 4mm thick tinted glass and one shutter using stainless steel wire cloth 0.36mm nominal dia & 1.18mm width aperture for mosquito proofing with good quality bearing handle, lock, rubber beading and glazing clips etc using following aluminium powder coated sections conforming to catalogue of 'JINDAL' or of equivalent make complete all as specified and directed by Engr-in-Charge. (a) Bottom frame - 20620 (b) Top frame & vertical - 20621 (c) Handle (side) - 20606 (d) Shutter inter lock - 20724(e) Shutter top & Bottom - 20844 (f) Glazing clips - 19352.
76	S & F ventilators/louvers using 4mm thick x 10cm wide frosted glass strips and following aluminium powder coated sections conforming to catalogue of 'JINDAL' or of equivalent make and rubber beading etc all as directed(a) SP : 20048(b) Glazing clips : 19352
77	M&L for preparing new surfaces of wood of any description no otherwise described over 10cm width or girth and apply two coats of synthetic enamel paint over a coat of pink primer all as specified and as directed.
78	Dismantling of wrought or MS work of any description etc as directed.
79	M&L for MS framed work conforming to grade E-165 (Fe-290) or Fe-310-O of MS angle or other sections, such as grills, gratings with ends of bar shouldered and / or riveted or forged into spikes framed guard bars; railings and like completed all as directed by Engineer-in-charge.
80	S&F framed work for doors or gate of angle, plain sheet or other sections etc. complete drilled for fixing of steel sheeting, incl necessary welding etc of grade Fe-410-w(Gde-E-250 quality B) complete incl dismantling structural steel incl doors or wrought iron work of any desc and any position, gates etc
81	M&L for preparing new surfaces of steel over 10cm in width or girth,not otherwise described and applying two coat of synthetic enamal (ordinary tint) over a coat of red oxide primer all as specified and as directed.
82	Dismantling of plain or corrugated steel sheeting in roof covering complete all as specified and directed.
83	S & F roof sheeting prepainted galvalume aluminium zinc coating GI based corrugated/ semi corrugated steel sheet 0.50 mm thick, 150GSM of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.
84	S&F for rolled mild steel conforming to grade E-250 (Fe-410W, quality A) as in main and cross beams, hip and jack rafters, purlins, where connected to common rafters and running rails and guides for sliding doors, fixed with angle clips or other connecting plates.
85	M&L for PCC 1:3:6 type C-2, (using 40mm graded stone aggregate) of 75mm thick, laid in alternate bays including finishing the surfaces even and smooth using extra cement incl demoiltion of existing PCC complete all as specified and as directed.
86	Preparation of old decorated surfaces by brooming down and scrapping wherever necessary and applying one coat of white wash on ceiling.
87	Complete removal of existing treatment and M&L for applying 3 mm thick wall care putty and applying two coats of distemper oil emulsion on walls all as spd and directed.
88	Complete removal of existing treatment and applying two coats of weather proof exterior acrylic emulsion paint (1st Quality) on walls, cornices, borders, facia of chajjas & projected columns over and including priming coat of exterior primer complete all as specified and directed. Note :- Exterior acrylic emulsion paint shall be anit-fungal, dust resistant, water repellant, crack-bridging, weather proof type 1st Quality.
89	Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out any type of soil complete all as specified and as directed.
90	Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out hard/ dense soil complete all as specified and as directed.
91	Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft disintegrated rock complete all as specified and as directed.
92	M&L for PCC in 1:4:8 type D2(using 40 mm graded stone aggregate) in foundation complete all as specified and as directed.
93	M& L RCC M-25 Design mix for Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.
94	M& L RCC M-25 Design mix for Columns, pillars, piers, posts and struts complete all as specified and as directed.
95	M& L RCC M-25 Design mix for Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed.
96	M& L RCC M-25 Design mix for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.
97	M & L Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and as directed.
98	Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed.
99	M&L mild steel bars 10mm dia and over , cut to length , bent to shape required including cranking , bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) 0.9mm dia or securing with clips quality confirming to TMT bars complete all as specified and as directed.
100	Ditto all as per item no 11 above but 5mm dia and over upto and including 10mm dia in stirrups, spaces and binders complete all as specified and as directed.
101	M& L Formwork to sides Rough finished surface of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed.
102	M& L Formwork to Rough finished surface of concrete sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and as directed.
103	M&L for formwork to Rough finished surface of concrete sides and soffits of roof beam, lintels etc. including supports,overhangs and also splays between floors and beams complete all as specified and as directed.
104	M&L for formwork to Rough finished surface of concrete sides and soffits of roof slab not exceeding 200mm thk . including supports,overhangs
105	M & L Formwork to Rough finished surface of concrete edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide
106	M&L broken hard core gauge, n exc 63mm deposited spread and leveled in layers n.exc 15cm thick water and rolled/rammed true surfaces complete all as specified and as directed.
107	M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed.
108	M&L for damp proof course 40mm thk to horizontal or vertical surfaces in cement concrete 1:2:4 type B-0 with WPC as per manufacturer’s instructions including necessary formwork complete all as specified and as directed.
109	M&L for 100 mm thick PCC in 1:4:8 type D2(using 40 mm graded stone aggregate) as in sub base complete all as specified and as directed.
110	M&L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and as directed.
111	M&L for rendering 15mm thick cement plaster 1:4 on concrete surfaces using water proofing compound of finished with sponge finish (note WPC shall be measured and paid separately) complete all as specified and as directed.
112	Supply only integral water proofing compound
113	M&L for 10mm thick cement plaster in CM 1:6 on brick surface finished even and smooth without using extra cement complete all as specified and as directed.
114	M&L for 5mm thick plastering in CM 1:3 on concrete on fair faces of bricks or concrete surfaces of ceiling finished even smooth with thin layer of sagol finish complete all as specified and directed.
115	M/L for non skid coloured ceramic tiles (of any colour) flooring 7 tto 8 mm thick area of each tile exceeding 0.11 sqm and not exc 0.18 sqm with joint free tiles set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 15mm thick cement screed bed in CM 1:6 complete all as specified and as directed.
116	M & L for 450 x 300 x 6 to 7 mm thick, coloured glazed ceramic tiles as in skirting/dado laid and jointed in neat cement slurry and pointed in coloured cement to match complete over and including triangular filleting on top in cement mortar 1:4 complete all as specified and directed.
117	M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint over one coat of primer all as specified and directed.
118	M&L for preparation of new plastered surface and appliying three coats of white washing on ceiling complete all as specified and as directed.
119	M&L for preparation of new plastered surfaces of walls and applying three coats of white wash complete all as specified and as directed.
120	M/L 75 mm thick PCC 1:3:6 type C2 ( using 40 mm graded stone aggregate) as in plinth protection/ path etc finished even and smooth without using extra cement complete all as specified and as directed.
121	M&L for designed glossy finish chequred coloured tiles (path tiles) 25cmx25cmx22mm thick laid over 15 mm thk screed bed in CM 1:6 set jointed in neat cement slurry and pointed in coloured cement matching to tiles all as specified by Engr-In-Charge
122	S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet, reinforced with M.S square tube, supplying & fixing in opening as per specifications, drawings complete all as specified and as directed.
123	M&L 75mm dia Cast iron floor Trap with steel grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and as directed.
124	S & F 75mm dia cast iron soil , waste and vent pipe in any length with or without ears with cement joints laid in floors/ trenches complete all as specified and as directed.
125	S &F salt glazed stone ware gully traps squre of size 150 x 150 mm including setting & jointing to drains in CM (1 ; 2) including eartwork, concrete in beds, surrounds, kerbs ettc and CI grating etc complete all as directed by Engr - In- Charge.
126	M & L water proofing treatment to RCC roof slab, walls, chajjas etc, shall be carried out as specified below and as directed by Engr-in-charge(a) M & L for 10 mm thick plaster screed bed layer in CM 1:3 on concrete surfaces (b) Preparing plastered surfaces of roof slab, walls, chajjas etc, by brooming with broom sweeping free from dirt dust etc and evenly applying a coat of approved bituminous primer @ 0.20 Kg/Sqm of area complete all as specified. (c) Laying APP polymer modified approved membrane, non woven, polyster, weighing not less than 3.5 Kg/Sqm with laps and overlaps as specified and joints sealed and applied complete by torch application method all as specified and directed by Engr-in-charge, Carrying out test by flooding water for 24 hrs for leakage and seepage and rectifying the same to the entire satisfaction of GE. (d) Finally applying a coat of solar reflective bituminous aluminium paint @ 0.15 ltr/Sqm on the top of membrane surfaces complete all as specified and as directed by Engr-in-charge.
127	S & F 600mm X 450mm X 5.5mm thick bevelled edge mirror of selected quality glass mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers with aluminium beading all around fixed in repairs complete all as specified and as directed.
128	S & F vitreous china wash down water closet pan ( pedesal pattern ), white including connection to drain ( or outgoing pipe ) and to flushing pipe with and including Plastic water closet seat,closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device including 10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, including flush pipe 32 mm dia.complete all as specified and as directed.
129	S & F wash hand basins, vitreous china of size 550mm X 400mm ( flat back or angle back type) including cutting for and pinning in ends of brackets or erecting stand inclusive of supply of 32 mm bore waste fittings brass chromium plated with long screwed shanks and fly nuts,screwed for iron pipe and fixing waste pipe including 15 mm bore CP fancy type Pillar cock with long shank etc. complete all as specified and as directed.
130	S & F brass chromium plated Tubular towel rail 20mm dia \\"D\\" type 60cm long complete all as specified and as directed.
131	S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.
132	S & F 15 mm chromium plated 2 way bib cock fancy type with wall flange complete all as specified and directed.
133	S & F 15 mm stop valves / angular stop cock, fancy type cast copper alloy chromium plated with crutch or butterfly handle, screwed down and screwed both ends for iron pipe or for union complete all as specified and directed.
134	S & F 15 mm bore, 600 mm long PVC connections with PTMT nuts complete fixed to iron pipe at both ends complete all as specified and directed.
135	S & F 125 mm dia brass chromium plated shower rose including shower arm of approved quality complete all as specified and as directed.
136	S & F chromium plated soap dish fixed to plugs with chromium plated brass screws complete all as specified and as directed.
137	S & F wall mixer (3-in-1) including telephonic shower for 15 mm bore of pipe complete all as specified and as directed.
138	S & F Stainless Steel toilet paper holder complete all as specified and as directed.
139	S&F 15mm dia bore GI tubing \\"medium grade\\" galvanized with all fittings and fixed complete to walls and ceilinng or laid in floors etc complete all as specified and as directed.
140	S&F 20 mm dia bore GI tubing \\"medium grade\\" galvanized with all fittings and fixed complete to walls and ceilinng or laid in floors etc complete all as specified and as directed.
141	S&F gun metal globe or gate valves with iron wheel head, screwed boh ends for iron pipe and fixed of 20mm dia of ISI marked complete all as specified and as directed.
142	S&F rotational moulded polythylene water storage tanks of double layers ISI marked (cylindrical vertical with colsed top) hoisted and fixed in postion of 500 ltrs capacity complete all as specified and directed.
143	S & F 20mm dia. ball valves, high pressure, with polythene float and fly nut complete,screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed.
144	Cutting into exising manhole for connecting new drain making good to pipe and rendering cutting out existing benching for and forming benching channel (1/2round or 3/4 section ) in cement concrete 1:2:4 type B1 smooth finish and reforming benching as required complete all as specified and as directed.
145	M&L for cement concrete 1:4:8 type D-2 in concrete bed to 150mm dia drain pipes including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and as directed.
146	M&L RCC pipes class NP-2 with socketed ends laid and jointed complete with rubber ring joints of 150 mm dia complete all as specified and directed..
147	M & L PVC (SWR) pipes 110 mm dia single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.
148	M &L PVC (SWR) pipes 75 mm dia single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.
149	M & L PVC (SWR) vent cowl 75 mm complete all as specified and as directed.
150	Taking down carefully exising unserviceable aluminium/copper Per Point wiring (light, fan, socket or power), complete (fitting such as switches,ceiling rose, pendent, regulators etc) removing material to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately and making good disturbed surfaces of wall, floor etc. complete all as specified and as directed.
151	M & L for Per Point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 Sq. mm (nominal area), two single core, PVC insulated and unsheathed FRLSH cable 1100 volts grade ISI-694 marked drawn through in and including heavy duty, PVC concealed conduit of white/ ivory colour including all accessories after chasing in wall of brick /stone mesonary heavy duty ISI marked, with GI sunken boxes 1.2 mm thick, 60 mm deep with earth dolly duly, covered with modular white cover plate with frame suitable for modular switches, including PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLSH cable as earth continuity conductor to common earth and connecting to earth dolly all as specified and directed for the following :-
152	One light /fan/Exhaust Point controlled by one way switch 5 Amps complete all as specified.
153	One 3 pin 5 Amps switch socket outlet Per Point controlled by one switch on independent board complete all as specified.
154	One 3 Per Point 5 Amps switch socket outlet Per Point controlled by one switch on the same board complete all as specified.
155	one Bell/Buzzer Per Points controlled by one bell push.
156	All as per item No 145 above for modular socket power Per Point but with stranded copper conductor 2.5 Sqmm (nominal area), single core, PVC insulated and unsheathed multistranded FRLSH cable 1100 Volt grade ISI-694 marked for 3 pin, 15 Amp socket outlet on independent board including PVC insulated multistranded copper conductor 2.5 Sqmm (nominal area) single core FRLSH cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified.
157	S & F Modular switch one way 6 Amps, 1 module complete all as specified.
158	S & F Modular switch one way 16 Amps, 1 module, with neon indicator complete all as specified.
159	S & F celling rose 2/3 terminals, PVC/ polycarbonate, isolated body ISI marked complete all as specified.
160	S & F modular five step type fan regulator up to 120 watt two module suitable for operation on 230 volt 50 HZ AC supply complete all as specified and as directed
161	S & F Modular socket, 6 Amps, 2/3 pin combination 2 module complete all as specified.
162	S & F Modular socket, 6/16Amps, 2/3 pin combination 2 module complete all as specified.
163	Suply and fix for Bell Electric Ding dong type suitable for operation on 230 volt 50 HZ A C supply complete all as specified and as directed
164	Suply and fix Lamp holder, PVC/Polycarbonate type with cord grip cap suitable for pendant fittings complete all as specifiedd and directed
165	S & F in modular Bell push modular 6 Amps single module complete all as specified.
166	Supply and fixing in replacement LED lights fitting 1x 18W, 220V, 100lm/W , 5700K certified with LM79/80 decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed
167	S & F in replacement of LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC ,100 lm/W,5700k certified with LM79/80 decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.
168	S & F in replacement of Decorative wall bracket light in SS housing shade material glass diemension (10.6 X10.6XX25.5 )cm, suitable for B22 base lamp complete all as specified
169	M & L in replacement of Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLSH cable with stranded copper conductor of size 4.0 Sqmm nominal area and drawing into PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size concealed in wall of brick /stone mesonary etc including one run of PVC insulated 4.0 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and as directed. Note:- Two runs of 4.0 sqmm cable,one run of 4.0 sqmm earth cable and one run of PVC conduit will be measured as one unit all as specified and as directed.
170	M & L in replacement of for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLSH cable with stranded copper conductor of size 6.0 Sqmm nominal area and drawing into PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size concealed in wall of brick /stone mesonary etc including one run of PVC insulated 6.0 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and as directed. Note:- Two runs of 6.0 sqmm cable,one run of 6.0 sqmm earth cable and one run of PVC conduit will be measured as one unit
171	M & L in replacement of for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLSH cable with stranded copper conductor of size 10.0 Sqmm nominal area and drawing into PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size concealed in wal lof brick /stone mesonary etc including one run of PVC insulated 10.0 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and as directed. Note:- Two runs of 10.0 sqmm cable,one run of 10.0 sqmm earth cable and one run of PVC conduit will be measured as one unit
172	S & F in replacement of Sheet metal 20 amp Single pole and neutral enclosure concealed in wallof stone masonary with a two pin and earth plug and socket complete with one single pole MCB 20 amps,10 KA breaking capacity,'C' series,240 V complete all as directed and specified by engineer in charge.
173	S & F in replacement of MCB SPN DB 12 way ,double door, with 100 amp rated busbar 240 V, SPN concealed in wall of stone mesonary/ fixed on wall/ board as requireed including all cutting holes in or through wall, making good to walls, including two coat of white/color washing/distempering etc to the disturbed surface to match the existing all as directed and specified by engineer in charge.
174	S & F in replacement of MCB SPN DB 16 way ,double door, with 100 amp rated busbar 240 V, SPN concealed in wall of stone mesonary/ fixed on wall/ board as required including all cutting holes in or through wall, making good to walls, including two coat of white/color washing/distempering etc to the disturbed surface to match the existing all as directed and specified by engineer in charge.
175	S & F in replacement of MCB SPN DB 4 way ,double door, with 100 amp rated busbar 240 V, SPN concealed in wall / fixed on wall/ board as required including all cutting holes in or through wall, making good to walls, including two coat of white/color washing/distempering etc to the disturbed surface to match the existing all as directed and specified by engineer in charge.
176	S & F in replacement of 40 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of single pole and neutral fixing with the MCB DB complete with connection testing and commissioning complete all as directed and specified by engineer in charge.
177	S & F in replacement of 63 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of single pole and neutral fixing with the MCB DB complete with connection testing and commissioning complete all as directed and specified by engineer in charge.
178	S & F in replacement of SP 5 to 32 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) fixing with the MCB DB complete with connection testing and commissioning complete all as specified and directed.
179	S&F in replacement,IP-43 ,MCB DB TPN 4 way ,double door, with 100 A busbar 415 V, and concealed/fixed on wall/board as required including all cutting holes in or through walls, making good to walls, ceiling etc including two coats of white / colour washing / distempering etc to the disturbed surfaces to match the existing
180	S&F in replacement of C Curve MCB SPN 40-63 Amps working on 240 volts, 50 HZ,10 KA IP-20 all as specified and directed.
181	M& L in repair for Earthing complete with galvanised steel earth plate electrode 600 x 600 x 6.3 mm thick, buried vertically in ground (Earth pit not less than 2.25 metres deep below normal ground level and top edge of the plate not less than 1.5 m below ground level), connected to and including Galvanised steel earthing wire 4mm dia by means of bolts, nuts & checknuts and washers etc; GI pipe 15 mm dia medium grade pipe for protection of G.I earth strip, both to be provided to the extent of 7.5 metres, all as shown on electrical plate No 3 of MES SSR-2009 Part-I, other end connected to electrical main switch board (inside the bldg) GI protection pipe buried in ground, laid under floors/plinths or fixed on walls or concealed in walls etc; with provision of mixture of charcoal dust & common salt packed upto minimum 150 mm all around the earth plate , including PCC 1: 3 : 6 type B-1 earth pit with RCC cover, with G.I 20 mm dia medium grade pipe and M.S funnel with wire mesh for watering arrangement, including necessary excavation and earth work in any type of strata & testing on completion complete all as specified & directed.
182	S & F in replacement of LED building security light fitting 35 Watt 230 V AC, 100lm/W, 5700k cetified with LM 79/80 outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65 protection complete.
183	Taking down ceiling fans of any sweep and make from any position carefully including disconnection of electric supply and disconnection of blades from fan and refixing the same after painting and overhauling complete all as specified and directed.
184	M & L Painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc and marking Srl No SM No / MES No with black paint, complete all as specified & directed.
185	Taking down carefully Geyser of capacity up to 25 ltrs from its position for repair/servicing such as removal of dust, checking, leakage testing ,rubber etc, re-assembling at its position with fastner after repair, painting connecting to electric system with suitable size cable and industrial plug top complete all as specified & directed.
186	Material & labour for preparation of old painted surfaces of geyser by scrubbing, cleaning with sand paper/wire brush etc making good surfaces and painting by applying synthetic enamelled first quality paint using spray gun in situ including filling cavities with filler and marking Srl No SM No / MES No with black paint complete all as specified & directed.
187	Supply and fix in replacement exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm complete all as sspecifiedd and directed
188	M & L for replacement of meter panel/ Switchgear panel doors made up of MS CRCA sheet powder coated having 2 mm thickness , cut to size and pressed to shape required as per size of existing meter panels installed at site including welding, fixing of hinges to sheet, provn of suitable locking arrangements, fixing of sliding bolts and further fixing to existing meter complete all as per directed by Engr in charge.
189	M&L for point wiring complete with 1.5 Sqmm two single core PVC insulated, unsheathed 1100volts agrade cable with multi stranded copper conductor FRLSH grade conforming to IS-694 part II with ISI mark FRLSH grade drawn through and including suitable size rigid non metalic PVC conduit in surface with all accessories, including suitable size sunkpresses steel or cast iron terminal box with wall surface by means of brass screw and sunk cup washers for mounting of switches, sockets, fan regulators etc including providing 1.5 Sqmm PVC insulated unsheathed multi stranded copper conductor cable as earth wire connected to metallic bodies of luminaires/fan etc at one end and to common earth dolly at other end all as specified for fan/light point all specified and directed by engineer-in-charge.
190	M&L for point wiring complete with 4.0 Sqmm single core PVC insulated, sheathed 1100 volts grade cable with stranded copper conductor FRLSH grade conforming to IS-694 part II with ISI mark FRLS grade drawn through and including suitable size in PVC conduit on surface with all accessories on wall/ceiling/floors/roofs etc including providing 4.0 Sqmm PVC insulated sheathed straded copper conductor cable as earth wire connected to metallic bodies of luminaires etc at one end and to common earth dolly at other end for One 3 pin socket outlet,15 Amps,independent all as specified by engineer-in-charge.
191	Ditto all as per item no. 180 above but One 3 pin socket outlet, 6 Amps on the same board with other switches, with cables 1.5 sq. mm size complete all as specified and directed by Engr-in-Charge.
192	S&F LED tubelight batten 20 W, 4 feet length,6500 k ,120 lms/watt, Aluminium housing, glare free, PH>0.95, THD<10% and should have supporting LM 79 & LM 80 test certificate from govt approved NABL accredited Lab complete all as specified and directed by Engr-in-Charge.
193	S&F lamp holder, PVC/polycarbonate type with back plate complete as specified and directed by Engr-in-Charge.
194	Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz,RPM 1200, Copper winding of sweep 250 mm complete as specified and directed by Engr-in-Charge.
195	Supply and fix of modular switch type 10 amps one way one module complete as specified and directed by Engr-in-Charge.
196	Supply and fix of modular Socket, 6A - 2/3 pin 2 module complete as specified and directed by Engr-in-Charge.
197	Supply and fix modular Switch socket Combination16A, 6 pin, 3 module, ISI marked, all as specified and directed by Engr-in-Charge.
198	S&F of Modular white cover with frame 6 module complete all as specified and directed by Engr-in-Charge.
199	S&F of Modular white cover with frame 3 module complete all as specified and directed by Engr-in-Charge.
200	S&F for ceiling rose, 2 to 3 terminals /PVC/Polycarbonate, isolated body complete as specified and directed by Engr-in-Charge.
201	M&L for unplasticised PVC pipes of 25 mm dia fixed complete to walls, ceilings or in floors etc., with all pipe fittings such as ends, elbows, unions, tees, reducing tees, adoptors, sockets, plugs, hose clips etc. and fixing to walls etc, complete with saddles (snap clips), wall clips, hooks complete all as specified and directed.
202	M&L for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade,3 core cross-sectional area 6 sq. mm complete all as specified and directed by Engr-in-Charge.
203	Supply and fixing sheet metal enclosure MCB DB SPN 4 ways double door type with suitable bus bar complete all as specified and directed by Engr-in-Charge.
204	Supply and fixing sheet metal enclosure MCB DB SPN12 ways double door type with 200 amps rated bus bar complete all as specified and directed by Engr-in-Charge.
205	Supply and fixing MCB SP, 6 to 32 Amps, ''C'' series 240 Volts, single phase, 10 KA breaking capacity complete all as specified and directed.
206	Supply and fixing MCB SPN, 32 Amps, ''C'' series 240 Volts, single phase, 10 KA breaking capacity complete all as specified and directed.
207	Supply and fix electric water heater,storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate,NRV, connection pipe piece etc complete all as specified and directed by Engr-in-Charge.
208	M&L for Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases in brick wall for concealed conduit wiring, etc. and making good, cutting exc 10 cm but not exc 20 cm girth complete all as specified and directed by Engr-in-Charge.
209	Supply and lay GI pipe galvanized, “Medium class”, including fittings 25 mm dia complete all as specified and directed by engr in charge.
210	Supply and fixed Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed, size 25 mm dia complete all as specified and directed by engr in charge. Please Enable Macros to View BoQ information

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents

Also Visit

Tenders

Maharashtra Tenders

Construction Tenders

Building Construction Tenders

Building Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Special Repair To Bldg No 20 Parvati Villa (Rcc Roof) And Provn Of Toilet Cum Bathroom And Paved Pathway At Bldg No 7 Pwd Under Ge South Pune, Pune-Maharashtra

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Special Repair To Bldg No 20 Parvati Villa (Rcc Roof) And Provn Of Toilet Cum Bathroom And Paved Pathway At Bldg No 7 Pwd Under Ge South Pune, Pune-Maharashtra

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us