|
| 1 | Demolition of cement concrete of any description and in any position(above/below of ground level) not otherwise specifically provided for as in sunken floor, plinth protection, roof kerb, foundation etc. all as specified and directed. |
| 2 | M&L for water proofing treatment to sunken floors of toilets, laboratories, bath, WCs, kitchen etc as under:- (i) Application of two component acrylic modified cementitious coating :- (a) The surfaces to be applied shall be completely dry and free from containments such as dirt, dust, oil, surface treatments and old coatings. Concrete substrates must be mechanically prepared using abrasive blast cleaning or milling to remove cement laitance existing coating and achieve a gripping profile that is clean, dry and free from laitance and any other from of surface containmation. The installation instruction in manufacturer's published literature shall be strictly complied with, including but not limited to the following:- (b) Chipping out any visible cracks in \\"V-Groove\\" pattern as applicable. Cleaning of cracks & filling with SIKA latex SBR 100 putty/Dr. Fixit 302 SBR latex/ perma latex SBR/FOSROC Nitbond SBR latex/Asian paint latex as required. Final cleaning of surface with powder grinder, wire brush, hair brush & vacum pressure. (c) Providing and applying a protection concrete 1:2:4, 50mm thick admixed with plastocrete over the applied water proofing coating on horizontal surfaces.(Admixture: Sikaplastocrete plus/FOSROC/Dr. Fixit/STP/CICO confirming to IS 2645.) (d) Dampen all surface immediately ahead of apllication of acrylic modified cementitious coating of SIKA top seal-107/Brush bomd FOSROC/Dr. Fixit/STP/CICO. (e) Whilst the surface is still damp from saturation (SSD) apply one coat of acrylic modified cementitious coating of SIKA top seal-107/ Brush bond FOSROC/Dr. Fixit/STP/ white first coat is wet. |
| 3 | (f) Apply glass fabric sheet as per manufacture instructions while the first coat is wet. (g) Once touch dry, apply second coat of acrylic modified cementitious coating of viscosity as per manufacturer ins on the entire area. Second coat shall be applied after 6-8 Hrs of application of previous coat and in the direction right angle to the previous coat. (h) The waterproofing coating shall be taken to a height minimum 300mm above the finished floor level on the vertical surface. (j) It is essential to cure acrylic moified cementitious coating immediately after application (min 6-8 hrs drying) for a min of 3 to 5 days to ensure full cement hydration and to minimize cracking. (k) A protection plaster (15mm thick) in ready mix mortar to be a apllied on the walls. (l) All the corners and joints shall be pretreated with an elastic waterproofing sealing tape with a woven bonding mesh on each surface and an elastic expansion zone in the centre of make seal tape SIKA/FOSROC/Dr. Fixit/STP. (m) The membrane has to be protected in accordance with the manufacturer's recommendation until placement of concrete. The membrane to be inspected for damage just prior to concrete placement and carryout repairs in accordance with manufacturer's recommendations. (n) Waterproofing treatment shall be carried out through authorised applicators authorised. |
| 4 | (o) All the joints of pipes and traps within the sunken portion shall be sealed properly by epoxy sealant. (p) All CI/PVC Traps in sunken slabs to be enclosed with PCC 1:1.5:3 (using 40mm graded crushed stone aggregate) (min 15cm) all round. (q) The sunken portion shall be filled with PCC 1:5:10 type E-2 (using 40 mm graded crushed stone aggregate) complete all as specified. (r) Providing drainage spout pipe GI 40mm dia bore light grade upto outside of outer wall (Approx 300 mm to 450 mmlong) incl cutting to existing wall and making good the distrubed surface complete all as specified and directed. (s) Providing 25mm thick cement concrete 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) as in flooring for laying floor finishes all as specified. Note:- Items no. (n) to (s) shall be measured and paid seperately. |
| 5 | M&L for PCC 1:5:10 type E2 using 40 mm graded stone agg as in filling, fdn and mass concrete in sunken floor complete all as specified and directed. |
| 6 | M&L 25 mm thick cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in sub base for receiving the floor finishes complete all as specified and directed. |
| 7 | M&L for removel of existing treatment (incl demolition of existing mud phuska/existing padding/ APP/ tarfelt) ,all loose gravel cement mortar , dirt, oil, grease and foreign material by jet of dry air, roughening and clean the surface mechanically or by grinding to make it smooth before application loose existing bituminious material manually and with heat torch gun to get smooth plain finished surface with no loose material on surface . Repair all joints & cracks and apply primer with smart care epoxy primer to seal the pores/cracksand enhance the adhesion of the coating. • Apply first coat of fibres reinforced elastomeric liquid water proofing membrane formulated with PU hybrid poymers and reinforcing acrylic fibres with sun reflective index (SRI) of 100-110, having minimum elongation of 300% to 350%, tensile strength of 1.8 Mpa to 2.9 Mpa and shall have cracks bridging ability upto 10-12 degree celcius with 33% dilutioon of priming coat. Laying of fiber mesh of 0.3mm thickkness weave in leno pattern having 45 gsm/sqm and pasting it properly with overlap of 50 mm and allow it to dry for 10 to 12 Hrs. Apply second of undiluted coat @0.45ltr/sqm and allow it to dry for 4 to 5 Hrs. Apply third and final coat undiluted @0.45 ltr/sqm all as specified and as per manufacturers specification having warranty for 10 years . Note : Application of water proofing treatment will be done by Authorised Applicator only . |
| 8 | M&L for cement concrete 1:2:4 type B-1 using 12.50mm graded stone aggregate as in roof padding complete all as specified and directed by Engineer-in-Charge. |
| 9 | M&L for PCC 1:2:4 type B0 (using 20mm graded stone agg) as in roof kerbs or mud stops, rounded or chamfered on edges with WPC complete all as specified and directed by Engineer-in-Charge. |
| 10 | M&L for glazed ceramic coloured tiles in vertical surface of size 450X300x7mm thick joint free on and incl 10mm thick screed bed in CM 1:4 set and jointed in neat cement slurry and pointed in colored cement mixed with pigment to match the colour of tiles including demolition of existing tiles and screed complete all as speciifed and directed by Engineer-in-Charge. |
| 11 | M&L non skid coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.11 sqm to 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to match including 15 mm thick rin CM 1:4 and including demolition of existing tiles and screed complete all as spcified and directed by Engineer-in-Charge. |
| 12 | M&L for non skid dark/light coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.18 sqm but n. exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or coloured cement to match including 15 mm thick screed bed in CM 1:4 and dismantling of existing tile complete all as specified. |
| 13 | M&L for green marble work 14-16 mm thick (table rubbed and polished) in steps, jambs, shelves, pillars window cills, cooking platforms, stair case and like in pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade incl 15 mm thick screed bed in ready mix mortar incl demolion of existing complete all as specified and directed. |
| 14 | M&L for 75mm thick cement cocnrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection finishing the surface even and fair complete all as specified and directed by Engineer-in-Charge. |
| 15 | Demolition of brick work or stone boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc. |
| 16 | M&L for brick work with fly ash brick, straight or curved on plan exc 6m mean radius built in CM 1:6 brick in fixed complete all as spcified and directed by Engineer-in-Charge. |
| 17 | M&L for brick work with fly ash bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed. |
| 18 | M&L for Chipping off existing loose, damaged concrete from RCC members of all affected RCC columns, beams, slabs and chajjas on external and internal facades, etc for providing PMM (Polymer modified cementitious mortar):- (i) Dry sub strate surface and free of debris & dust. (ii) Applying epoxy bond coat on the sound substrate using approved spray machine & ensuring that no pin holes are visible. (In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes. (iii) Immediately after application of epoxy bond coat as above apply PMM (Polymer modified cementitious mortar) of n exc 50 mm thickness. Note : Application of PMM shall be pre packed ready to use. (iv) PMM surface to be moist cured for three days followed by air curing in temperature as rcommended by manufacturer complete all as specified and directed. Note: - Cost of formwork, bldg ht upto 12 mtr, shall be deemed to be included in unit rate quoted by the Contractor. |
| 19 | M&L for 12 mm thick rendering with ready mix mortar of approved make on brick work/stone/concrete wall etc. internal surfaces finished even and smooth without using extra cement complete all as specified and as directed. |
| 20 | M&L for 15 mm thick rendering with ready mix mortar of approved make on brick work/stone/concrete wall, facia, projection,chajja etc. external surfaces finished even and smooth without using extra cement complete all as specified and as directed. |
| 21 | M&L for 15 mm thick rendering with ready mix mortar of approved make on brick work/stone/concrete wall, facia, projection, chajja etc. external surfaces finished even and smooth without using extra cement incl taking down existing plaster of any size incl raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed. |
| 22 | M&L for 12 mm thick rendering of ready mix mortar of approved make on brick work/stone/concrete wall etc. internal surfaces finished even and smooth without using extra cement incl taking down existing plaster of any size incl raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed. |
| 23 | M&L for 5 mm thick rendering of ready mix mortar of approved make on brick work/stone/concrete wall etc. internal surfaces finished even and smooth without using extra cement incl taking down existing plaster including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed. |
| 24 | M&L for preparation of new plaster surface and applying two coats of cement base paint on wall surface complete all as specified and directed by Engineer-in-Charge. |
| 25 | M&L for preparation of new plaster surface and applying two coats of Oil bound distemper of wall over a coat of chalk whiteing primer on plastered surface wall complete all as specified and directed by Engineer-in-Charge. |
| 26 | M&L for preparation of new plaster surface and applying three coat of white wash on ceiling complete all as specified and directed by Engineer-in-Charge. |
| 27 | Taking down existing window & Supplying and fixing of Unplasticised Poly Vinyl Chloride (UPVC) combination villa casement window ( size n. exc 1.00 sqm) - (Open Villa Window with grill fixed inside so that the shutters to be openable outside with SS mesh shutters opening inside) in white color - duly manufactured using uPVC reinforced profiles (Composition of profile shall consists a minimum 6 PHR of TiO2 and not more than 10 PHR of CaCO3 for every 100 parts of PVC resin) of sections not less than (109 mm x 58 mm x 2.20 mm for outer frames, 78 / 40 mm x 60 mm x 2.20 mm (Glass Sash) for casement shutter frames capable of mounting single glazing and double glazing system, Mesh Sash 84 mm x 43 mm x 2.20mm, fixed Mullion T made of 109 x 79 mm reinforced with hot dip galvanized up to 120 GSM of minimum thickness of 1.2 mm for Outer frame / 1.5 mm for Sash prefabricated & welded through fusion welding including 10 mm square guard bars with 6\\" (152.4 mm) pitch. The window sash shall be fitted with both single and double glazing systems of reputed make duly fixed with Black color Gasket for sash & Glazing bead and accessories for casement window - friction hinges of stainless steel grade 304-2 no’s per sash, handle 1 no. per sash, Espag locking system suitable concealed 1 No. per sash provided with raiser wedges for smooth operation and the system is to be installed at site using anchor fasteners, UV resistant silicon sealant outside and paintable silicon sealant inside, easy glazing / deglazing at site, etc. Including cost and conveyance of all materials, accessories, labour charges for transportation, erection at site complete for finished item of work.Single Glazing: 5mm thick Clear Float Glass |
| 28 | Taking down existing window & Supplying and fixing of Unplasticised Poly Vinyl Chloride (UPVC) combination villa casement window ( size exc 1.00 sqm)- (Open Villa Window with grill fixed inside so that the shutters to be openable outside with SS mesh shutters opening inside) in white color - duly manufactured using uPVC reinforced profiles (Composition of profile shall consists a minimum 6 PHR of TiO2 and not more than 10 PHR of CaCO3 for every 100 parts of PVC resin) of sections not less than (109 mm x 58 mm x 2.20 mm for outer frames, 78 / 40 mm x 60 mm x 2.20 mm (Glass Sash) for casement shutter frames capable of mounting single glazing and double glazing system, Mesh Sash 84 mm x 43 mm x 2.20mm, fixed Mullion T made of 109 x 79 mm reinforced with hot dip galvanized up to 120 GSM of minimum thickness of 1.2 mm for Outer frame / 1.5 mm for Sash prefabricated & welded through fusion welding including 10 mm square guard bars with 6\\" (152.4 mm) pitch. The window sash shall be fitted with both single and double glazing systems of reputed make duly fixed with Black color Gasket for sash & Glazing bead and accessories for casement window - friction hinges of stainless steel grade 304-2 no’s per sash, handle 1 no. per sash, Espag locking system suitable concealed 1 No. per sash provided with raiser wedges for smooth operation and the system is to be installed at site using anchor fasteners, UV resistant silicon sealant outside and paintable silicon sealant inside, easy glazing / deglazing at site, etc. Including cost and conveyance of all materials, accessories, labour charges for transportation, erection at site complete for finished item of work.Single Glazing: 5mm thick Clear Float Glass |
| 29 | S&F steel window box type made of ERW tube hollow P section of size 60mmX25mm double rebated outer frame comprising double shutters i.e. guaged skelton & glazed, shutter frame of ERW tube P section size 50mmX20mm with two openable leaf for each shutter consisting two Nos sash bar of T-section 20mmX3mm welded to frame with one vertical mullion of ERW box type T-section of size 60mmX25mm and FI 2mm thick welded/ screwed to frame for fixing of wire gauge including MS guard bars, fittings and fixtures welded to frame/ shutters as given below and all as shown on drg No. CEJZ/TD-1020/08 Sh 1/3 to 3/3 completeincl two coat of painting incl taking down old existing window :- (i) Hold fast,150mm long of flat iron 12mmX3mm- 04Nos per window (ii) Handle of Z section 20mmX25mm,100mm long-01Nos per leaf (iii) MS Tower bolt 150mm long-02 Nos per leaf (iv) Z section 20mmX25mm,100mm long stopper -01 Nos per leaf (v) Cleat 55mm long of hollow square 15mmX12mm -02 Nos per leaf (vi) MS pintol hinges size 75mmx12mm- 2 Nos. per leaf (vii) Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts (four Nos for each window). (viii) Painting with one shop coat of zinc chromate primer. Note: Wire cloth, glass shall be measured and paid for separately |
| 30 | Taking down chowkats with shutter n.exc 1.50 Sqm each (without taking off shutter for the chowkats) complete all as specified and directed. |
| 31 | Taking down chowkats with shutter exc 1.50 Sqm but n exc 4.00 sqm each (without taking off shutter for the chowkats) complete all as specified and directed. |
| 32 | Taking down shutter of any description exc 1.00 Sqm but n.exc 2.00 Sqm each complete all as specified and directed. |
| 33 | S&F factory made single extruded WPC solid door Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum Compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. . |
| 34 | S&F factory made single extruded WPC solid door Frames/ Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum Compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. |
| 35 | S&F factory made single extruded WPC solid door frames/ chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum Compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. |
| 36 | S&F 30 mm thick factory made single extruded WPC solid plain flush door shutter comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. |
| 37 | S&F 35 mm thick factory made Natural fiber composit door shutter with CNC deisgn pattern/plain as approved by EIC, of required size having minimum 40% high strength plant derived fibers, consist of thermoset polymers, Non-toxic additives (minimum toxicity index of 12 for 100 gms), having density of 650 kg/cum, Modulus of elasticity (3.4), screw withdrawl strength strength of 1800N (Face) and 900N (edge), having interlaminar shear strength and Thermal stability, all as per specification of manufacturer and direction of Engineer-in-Charge. |
| 38 | S&F of 35mm thick single piece factory made wire gauge door shutter and incl of wirecloth (stainless steel and aluminium XPM) manufacturing by PVC sheets printed 5mm thick on both side of frame made out of M.S tube 19 SWG, size 19x19mm complete in all respect with lock rail & beautified by PVC beading all around fixed with PVC solvent cement . Complete as per drawing number CEPZ/ TD-378/ Sheet 1/1 dated 27/12/2011 complete all as specified and directed. |
| 39 | S&F stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 40 | S&F in repair stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 41 | S&F 3mm thick acrylic sheet transparent glass ordinary quality and glazing with silicon and filling gap with oil putting in squares n exc1.00 Sqm each fix on steel, wooden etc frame complete all as specified and directed. |
| 42 | S&F in repair 3mm thick acrylic sheet transparent glass ordinary quality and glazing with silicon and filling gap with oil putting in squares n exc1.00 Sqm each fix on steel, wooden etc frame complete all as specified and directed. |
| 43 | M&L for preparation of new wooden surface exc 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed. |
| 44 | S&F in repair 300mm, mild steel ordinary rat tail rod pattern springs, including roller and roller plate joint through welding/bolt in metal/wooden frame to be carried out complete all as specified and directed. |
| 45 | S&F aluminium anodized barel tower bolt of extruded section 150mm long ISI marked complete all as specified and directed. |
| 46 | S&F aluminium alloyed handle fabricated type anodized of size 150 mm long ISI Marked complete all as specified and directed. |
| 47 | S&F 100mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 through bolt or with screw complete all as specified and directed. |
| 48 | S&F Aluminium alloy, anodised, sliding door 300 mm long ISI Marked bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixedcomplete all as specified and directed. |
| 49 | Supply and fixing in repair cutrain rod 20mm dia of Mild steel with PVC Coated with fixing brackets, stops, rollers etc fixed to wall with screws, PVC plug including taking down existing curtain rod complete all as specified and directed. |
| 50 | S&F in repair 18/19 mm thick one sided prelaminated colour WPC board for cupboard shutter and frame & fixed at site. Complete all as specified and directed. Note: Board edges finished properly with strip on band edges. |
| 51 | S&F in repair 18/19 mm thick plain/white WPC board for cupboard frame & fixed at site. Complete all as specified and directed. Note: Board edges finished properly with strip on band edges. |
| 52 | S&F in repair 12 mm thick plain/white WPC board for cupboard frame & fixed at site. Complete all as specified and directed. Note: Board edges finished properly with strip on band edges. |
| 53 | S&F in repair 6 mm thick plain/white WPC board for cupboard frame & fixed at site. Complete all as specified and directed. Note: Board edges finished properly with strip on band edges. |
| 54 | S&F continuous piano hinge (approx. 1–1.5 inch width) made of stainless steel or powder-coated MS, for kitchen cupboards/wardrobes/shutters, including necessary screws, cutting, alignment, and fixing complete. |
| 55 | S&F aluminium alloyed handle fabricated type anodized of size 100 mm long complete all as specified and directed. |
| 56 | S&F 75mm size hasp and staple safety type aluminium anodised brass with mild steel hinge pin including bolt to hinge plate and fixed with screw complete all as specified and directed. |
| 57 | S&F 500 ltr capacity rotational moulded polyethylene 3-layer white water storage tanks (cylindrical vertical with closed top) with suitable base platform or PVC base cover ,hoisted and fixed in postition all as specified in SSR Part I complete all as specified and directed. |
| 58 | S&F 500 ltr capacity rotational moulded polyethylene 3-layer white water storage tanks (cylindrical vertical with closed top) with suitable base platform or PVC base cover , hoisted and fixed in postition all as specified in SSR Part I including dismantling of water tanks complete all as specified and directed. |
| 59 | S&F in repair ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 20mm bore complete all as specified and directed. |
| 60 | S&F in repair Gun-metal, globe or gate valves,20 mm dia with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed. |
| 61 | S&F in repair stop valves or angel valve cast copper alloy 15mm bore fancy type chromium plated alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc complete all as specified and directed. |
| 62 | S&F in repair bib taps cast copper alloy 15mm bore fancy type chromium plated alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. |
| 63 | S&F in repair pillar taps, cast copper alloy fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe 15mm bore and fixed. |
| 64 | S&F in repair brass chromium plated shower rose fancy type 125mm size with swivel joints, any size, including fixing to steel pipe or union with brass CP arm 195mm long, 15 mm size complete all as specified and directed. |
| 65 | S&F in repair Brass chromium plated concealed stop valve with brass body, chrome plated trim plate, including necessary fittings complete all as specified and directed . |
| 66 | S&F in repair brass chromium plated tubular towel rail 20mm dia, D type, 60 cm long with flanges complete all as specified and directed by Engineer-in-Charge. |
| 67 | S&F in repairs vitreous china wash down water closet (pedestal pattern)fixing with bolts ,white colour, incl stainless steel L-type jet spray with 1m hose pipe, connection to trap, and to flushing pipe, anti-syphonage pipe, etc. incl seat covercomplete including making good to floor complete all as specified and directed complete all as specified and directed. |
| 68 | S&F in repair vitreous china squatting pan “Orrisa Pattern” white of size 580x440mm with internal foot rest with `P’ or `S’ trap, integral foot rest including water connection to trap and flushing pipe etc complete and bedding in PCC 1:7:12 type F-2 (using 40mm graded crushed stone aggregate) complete all as specified and directed. |
| 69 | S&F in repair vitreous China wash basin, with pedestal white flat back, size 550x 450mm excluding taps, waste, chain and plug and porcelain stopper but including brackets and coupling complete all as specified and directed. |
| 70 | S & F in repair PVC low level flushing cistern 10ltr capacity, with syphonic, action PVC float valve, brackets and 32mm bore PVC flush pipe etc complete all as specified and directed. |
| 71 | S&F in repair PVC waste pipe 32mm dia 800mm to 1200 mm long fixed to wash fitting of wash basin and sink all as specified and directed. |
| 72 | S & F in repair PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed. |
| 73 | S&F in repair brass spindle with nylon washer and removing leakage of water of any concealed type suitable for 15 to 25mm bore pipe complete all as specified. |
| 74 | S&F in repair tap/valve head/ handle 15mm dia cast copper alloy fancy type chromium plated round/square hole complete all as specified and directed. |
| 75 | S&F in repair stainless steel L-type jet spray with 1m hose pipe for fitting in WC complete all as specified and directed by Engineer-in-Charge. |
| 76 | S&F GI tubing 15mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings ISI marked including taking up and down complete all as specified and directed. |
| 77 | All as per Srl item No 74 above but fixing only (old serviceable pipe re-used). |
| 78 | S&F GI tubing 20mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings ISI marked including taking up and down complete all as specified and directed. |
| 79 | All as per Srl item No 76 above but fixing only (old serviceable pipe re-used). |
| 80 | S&F GI tubing 32mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings including taking up or down old pipe complete all as specified and directed. |
| 81 | Dismantling of cast iron ,PVC or SGSW drain pipes, jointed in cement mortar and taking out of trenches , if required. |
| 82 | S&F PVC (SWR)pipes 110mm dia in any length with rubber ring joint fixed to wall/floor upto 12m height complete all as specified and directed. |
| 83 | S&F in repair PVC (SWR) bends 110mm dia, in any radius, complete all as specified and directed. |
| 84 | S & F in repair 110 bore PVC(SWR) Branch pieces (Single T), single (equal or unequal ), ordinary or inverted ) ( or with parallel branches with oval access door complete all as specified and directed. |
| 85 | S&F in repair PVC vent cowl of size 110mm. |
| 86 | M&L in repair for PVC(SWR) floor trap plain including jointing with solvent cement 100mm dia complete all as specified and directed. |
| 87 | S&F in repair stack clamps (110 mm pipe) out of 20x1.5 mm galvanised mild steel incl stays, bolt and nuts and securing ends of stays to wall or roof complete all as specified and directed. |
| 88 | S&F in repair 600mm X 450mm(min size) beveled edge mirror of selected quality glass fancy type as approved by GE and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 89 | M&L cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base complete all as specified and directed. (to raise level only) |
| 90 | M&L for 60 mm thick PCC (M-35) factory made with gray cement and pigment glossy finishes coloured interlocking tiles/ paver block of shape/ size as conforming to IS 15658, joints will be filled with fine sand, incl dismantling of existing tiles complete all as specified and as directed by Engr-in-Charge. Note Sand will be paid under relavent item. |
| 91 | M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed by Engineer-in-Charge. |
| 92 | M&L rubber moulded chequered cement concrete coloured tiles with glossy finish 30cm x 30cm x 25mm thick, with grey cement and pigment, set, jointed and pointed in neat cement slurry with pigments in floors, including m thick 1:4 CM screed bed incl dismantling of existing tiles complete all as specified and as directed by Engr-in-Charge. |
| 93 | S&F machine cut kota stone slab flooring 20-22mm thick over cement screed base 20mm thick in 1:6 with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (with bees wax polish) including demolition existing complete all as specified and directed by Engineer-in-Charge. |
| 94 | Demolition of cement concrete (Reinforcment) of any description as OHT Tank, shelves, chajja etc. upto 12m height all as specified and directed by Engr-in charge. |
| 95 | Form work to rough finished surface of concrete flat, edges to soffits of shelve, chajja and like including supports over hangs |
| 96 | S&F 6mm dia and over TMT bar cut to length bent to shaps including cranking binding spirraly, hooping, hooking end and binding with MS wire (anealed) not less then 0.9 mm dia or securing with clips as specified. |
| 97 | M&L for RCC in 1:2:4 type B-1(using 12.5 mm graded stone agg) as in chajjas facia, shelves etc and similar work all as specified. |
| 98 | S&F in repair stainless steel grating with hole, round 101mm dia complete all as specified and directed. |
| 99 | M&L for removing existing pointing, raking out joints & flush pointing to bricks laid flat or brick tiles in pavings or brick tiles on roof with CM (1:3) including cleaning the surface grass, mud and like complete all as specified and directed. |
| 100 | M&L for preparation of old painted wooden surface exc 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 101 | M&L for preparation of old painted steel surface exc 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge. |
| 102 | M&L for preparation of old plastered surfaces of ceiling by brooming down, making good holes, cracks, etc and applying one coat of white wash incl cleaning the floor/ joinery surfaces, glass pans all as directed by Eng-in-charge |
| 103 | Complete removal of existing treatment on internal wall by scrapping with mechanical sander (having mechanical vaccum mechanism) with sanding pad of appropriate grit to make surface clean,free from dust, loose paint etc by skilled labour with mechanical sander having RPM of 1500 - 2700 rpm, with internal dust extraction system for clean environment, and preparation of old plastered/scrapped surfaces of wall by filling cracks by internal wall putty/crack fill paste and applying interior water proof wall care putty @ 1 Kg(undiluted) per sq mtr. of average thickness 1mm to 2mm over the prepared plastered wall surfaces, one or more coats and grinding the puttied surfaces with mechanical grinder for make the surface even and smooth for receiving primer and applying two coats of smooth Oil bound distemper with rich matt finish having voc less than 50 grams per ltr complying lead criteria @ 1 ltrs (undiluted)/10 sq mtrs diluted with water as per manufacturers instructions applied over of required shade (Company Depot Tinted) with silicon additives & Color stay technology, over and including priming coat of interior waterproof primer with Roller finish and allow 6- 8 hrs to dry the surface for second coats of paint complete all as specified and directed. Note:-Paint using Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed. |
| 104 | M&L for preparation of old plastered surfaces of wall by brooming down, making good holes, cracks, etc and applying one coat of white wash complete all as directed by Engineer-in-Charge. |
| 105 | M&L for preparation of old plastered surface of walls rubbing down, making good holes, cracks, etc and stopping etc on existing distempered surfaces and applying one coats of cement base paint on wall complete all as specified and directed by Engineer-in-Charge. |
| 106 | Complete removal of existing treatment on wall/ roof projections including facia, cornices, chajja etc by scrapping with mechanical sander (having mechanical vaccum mechanism) with sanding pad of appropriate grit to make surface clean,free from dust, loose paint etc by skilled labour with mechanical sander having RPM of 1500 - 2700 rpm, with internal dust extraction system for clean environment, and preparation of old plastered/scrapped surfaces of wall/ceiling by filling cracks by external wall putty/crack fill paste and applying exterior water proof wall care putty @ 1 Kg(undiluted) per sq mtr. of average thickness 1mm to 2mm over the prepared plastered wall/ceiling surfaces, one or more coats and grinding the puttied surfaces with mechanical grinder for make the surface even and smooth for receiving primer and applying Two or more coats of 100% Premium acrylic smooth exterior emulsion weather coat paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives & Color stay technology, Excellent dirt pickup resistance @ 1.79 litre/ 10 sqm diluted with water as per manufacturers instructions over and including priming coat of exterior waterproof primer applied @ 0.9 litre (Undiluted) / 10 sqm over old/new putty surfaces of wall/ceiling complete all as specified and directed. Note:-Paint using Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed. |
| 107 | Providing and fixing stainless steel plate rack of size 600mm x 600mm, 3-tier, wall mounted, fabricated from stainless steel 304 grade, including screws, rawl plugs, brackets and all fittings & fixtures complete all as specified and directed. |
| 108 | A Schedule of Credit for old/unserviceable demolished/ dismantled items has been catered for in the tender. The Schedule of Credit is pre-priced by MES. The final amount of the tender shall be arrived at after deducting the total amount of Schedule of Credit Rs. 62,590/- from the total amount of BoQ as per General Summary sheet catered for after Schedule of Credit. Please Enable Macros to View BoQ information |
