|
| 1 | Taking down chowkhats or frames with shutters(without taking off shutters from the frames) exc 1.50 sqm but n exc. 4 sqm each and removing from site and making good disturbed surfaces of wall in CM (1:3), complete all as specified and directed. |
| 2 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of any description n exc 1.50 sqm each and removing from site complete and making good disturbed surfaces of wall in CM (1:3) complete, all as specified and directed |
| 3 | Material and labour for 35mm thick factory made solid PVC (Wood plastic composite ) moulded gauged door shutter with wire mesh 0.18mm nominal dia of wire and average width of aperture 1.40mm in any number of division with brown wood grain texture , including S.S wire mesh shall be fixed with 15x15 square tubes in is rails with screwing 8x28mm heat metal Zink coated screws can be remove or fixing again after changing of wire mesh when needed.The density shall be as per manufactures instructions, complete all as specified and directed. |
| 4 | Material and labour for Providing and fixinging factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixed with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete, all as specified and directedNote: stainless steel butt hinges and necessary S.S screws shall be paid separately |
| 5 | Supplying and fixing Factory made single extruded WPC (Wood Polymer Composite) solid door frames/ Chowkhat of size 50x100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant including making good, complete all as specified and directed. |
| 6 | Supplying and fixing Factory made single extruded WPC (Wood Polymer Composite) solid door frames/ Chowkhat of size 65x125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant including making good, complete all as specified and directed. |
| 7 | Material and labour for box type steel window 1.25 mm thick made of ERW tube P-Section of size 60 x 25 mm double rebated outer frame comprise of glazed skeleton shutter(two gauged shutters and two glazed shutter) of ERW tube P-Section size 50 x 20 mm and 1mm thick one/two nos openable leaf consisting of two Nos sash bar of T-Section 20x3mm welded to frame with one no vertical mullion of ERW box type T-Section of size 60 x 25 mm and 1.25 mm thick and FI 2 mm thick welded / screwed to frame for fixing of glass including fittings and fixture like Handle, Tower Bolt, stopper, cleat, pintal hinges, hold fast etc.(a) Hold fast, 150 m Material and labour forong of 120mm x 3 mm made to shape -04 Nos per window. (b) Handle of Z sec 20mm x 25mm, 100 m Material and labour forong -1 No per leaf.(c) MS Tower bolt 150 m Material and labour forong - 2 No per leaf.(d) Z Sec 20mm x 25 mm, 100 m Material and labour forong stopper - 1 No per leaf.(e) Cleat 55 m Material and labour forong of hollow square 15mm x 20mm x.63mm welded to hinge -1 No per leaf.(f) MS Pintal hinges of size 75mm x 12mm - 2 Nos per leaf.(g) 12 mm square guard bar, 10 cm centre to centre.(h) 25x4 mm flat iron all around for joint of both frame.(j) One shop coat of red oxide primer and two coats of Synthetic enamel paint to MS window and guard bar complete, all as specified and directed.Note:(i) Including taking down old steel window and making good dismantled portion with PCC 1:2:4 type B0 including hold fast PCC (four No’s for Each window) & around required plaster in CM 1:4 and match with existing finishing, complete all as specified and directed. (ii) sheet glass and wire mesh shall be measured and paid separately) |
| 8 | Material & labour for box type steel ventilator made of ERW tube P-section of size 60mmx25mm outer frame (single rebated ) of ERW and FI 2 mm thick welded /screwed to frame for fixinging of sheet glass including fixtures and fittings like a stopper , cleat , pintal hinges , holdfast etc all as shown on drg No CEJZ/TD/1019/08 sheet 1/3 to 3/3 dt 01 May 2008 complete all as specified. (a) 10 mm Sq Guard bar 10 cm C/C(b) One shop coat of red oxide and two coats of synthetic enamel paint to MS ventilator and gaurd bar (c) MS Tower bolt 150m Material and labour forong - 2 No per leaf (d) Z Sec 20mm x 25 mm, 100 mMaterial and labour forong stopper - 1 No per leaf Note:(i) Including taking down old steel ventilator and making good dismantled portion with PCC 1:2:4 type B0 including hold fast PCC (four No’s for Each window) & around required plaster in CM 1:4 and match with existing finishing, complete all as specified and directed.(ii) sheet glass and wire mesh shall be measured and paid separately) |
| 9 | Supplying and fixing Sheet glass, 3mm thick ordinary quality, in squares, not exceeding 0.50 sqm in each pane fixing with oil putty. complete, all as specified and directedNote : upto four storey height including all scaffolding work |
| 10 | Supplying and fixing GI wire cloth, 0.56 mm nominal dia. of wire and average width of aperture 1.18 mm and fixed with tinned tacks,or galvanised wire staples, complete all as specified and directed. |
| 11 | Supplying and fixing repair 3mm thick plain glass etc and glazing with oil putty in Sqm n. exc 0.50 each pan, complete all as specified and directed. |
| 12 | Supplying and fixing in repairs stainless steel wire cloth 0.36 mm nominal dia. of wire and average width of aperture 1.4 mm and fixed with tinned tacks, or galvanised wire staples, complete all as specified and directed. |
| 13 | Supplying and fixing parliament hinges mild steel cold rolled 100mm long medium weight fixed .Complete all as as directed and specified |
| 14 | Supplying and fixing 150 mm Aluminium, anodised, barrel tower bolts of extruded section and fixinged, complete all as specified and directed. |
| 15 | Supplying and fixing 150 mm Extruded aluminium alloy handles, cast type, anodised, complete all as specified and directed. |
| 16 | Supplying and fixing Aluminium door stopper double support with rubber, complete all as specified and directed. |
| 17 | Supplying and fixing 300mm long aluminium alloy,anodised ,sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet,cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast- aluminium alloy and fixed, complete all as specified and directed. |
| 18 | Taking down cement plaster on brick/stone/concrete walls /ceiling incl racking out joints etc,hacking for key, scrubing down with water etc complete, all as specified and directed. |
| 19 | Material and labour for rendering 15 mm thick on fair faces of brick work or concrete surfaces on ceiling in CM 1:6. is to be finished even and smooth without using extra cement, complete all as specified and directed. |
| 20 | Material and labour for rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:4. is to be finished even and smooth without using extra cement (WPC shall be measured seperatly as per manufacturer's instructions), complete all as specified and directed. |
| 21 | Material and labour for rendering 10 mm thick on fair faces of brick work or concrete surfaces on ceiling in CM 1:3. is to be finished even and smooth without using extra cement, complete all as specified and directed. Please Enable Macros to View BoQ information |
| 22 | Material and labour for rendering 10 mm thick on fair faces of brick work or concrete surfaces on ceiling in CM 1:3. is to be finished even and smooth without using extra cement, complete all as specified and directed. Please Enable Macros to View BoQ information |
