Tender For Annual Operation, Maintenance And Providing Civil & Electrical Maintenance (Including Facility Management Services) For Office And Residential Complex At Block-B Area For 2 Years., Singrauli-Madhya Pradesh

TDR : 55578889

Tender Notice
BOQ

19 Days Left

Singrauli , Madhya Pradesh

Tender Brief : Tender For Annual Operation, Maintenance And Providing Civil & Electrical Maintenance (Including Facility Management Services) For Office And Residential Complex At Block-B Area For 2 Years.

Document Fees
Refer document

EMD
₹ 1289900.0 /-

Tender Value
₹ 10.31 Crore /-

Submission Date
10-06-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Carriage of material by Mechanical Transport including loading, unloading and stacking Lime, moorum, building rubbish Lead - 1 Km
2	Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.All kinds of soil
3	Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.
4	Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.
5	Surface dressing of the ground including removing vegetation and in- equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. All kinds of soil
6	Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared.
7	Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size derived from natural sources).
8	Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.
9	Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size derived from natural sources).
10	Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size derived from natural sources).
11	Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size derived from natural sources).
12	Centering and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns, etc. for mass concrete
13	Centering and shuttering including strutting, propping etc. and removal of form for: Suspended floors, roofs, landings, balconies and access platform
14	Centering and shuttering including strutting, propping etc. and removal of form for: Lintels, beams, plinth beams, girders, bressumers and cantilevers
15	Centering and shuttering including strutting, propping etc. and removal of form for: Columns, Pillars, Piers, Abutments, Posts and Struts
16	Centering and shuttering including strutting, propping etc. and removal of form for: Weather shade, Chajjas, corbels etc., including edges
17	Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but, excluding cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size derived from natural sources).
18	Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.
19	Brick work with FALG bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 ( 1 cement : 6 coarse sand )
20	Brick work with FALG bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 ( 1 cement : 6 coarse sand )
21	Half brick masonry with FALG bricks of class designation 7.5 in foundations and plinth in : Cement mortar 1:4 (1 cement : 4 coarse sand)
22	Half brick masonry with FALG bricks of class designation 7.5 in superstructure above plinth level up to floor V level. :Cement mortar 1:4 (1 cement : 4 coarse sand)
23	Providing and laying matt finished vitrified tile of size 300x300x9.8mm having water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.
24	Deduct for not providing hinges in doors, windows or clerestory window shutters with :Stainless steel butt hinges with stainless steel screws : For 2nd class teak wood and other class of wood shutters
25	Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). Kiln seasoned and chemically treated hollock wood
26	Providing and fixing flat pressed 3 layer particle board medium density exterior grade (Grade I) or graded wood particle board IS : 3087 marked, to frame, backing or studding with screws etc. complete (Frames, backing or studding to be paid separately): 12 mm thick
27	Providing and fixing Pre-laminated flat pressed 3 layer (medium density) particle board or graded wood particle board IS : 3087 marked, with one side decorative and other side balancing lamination Grade I, Type II exterior grade IS : 12823 marked, in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately). 18 mm thick
28	Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non- decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands andface veneers on both faces of shutters: 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
29	Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non- decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands andface veneers on both faces of shutters: 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S.piano hinges with necessary screws
30	Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors,windows and clerestory windows with hinges and necessary screws : 30 mm thick shutters With ISI marked M.S. pressed butt hinges bright finished of required size Kiln seasoned and chemically treated hollock wood
31	Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.
32	Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm
33	Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
34	Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets : 20 mm dia (heavy type)
35	Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. complete : 100x58x1.90 mm
36	Providing M.S. Piano hinges ISI marked IS : 3818 finished with nickel plating and fixing with necessary screws etc., complete. Overall width 35 mm
37	Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : 250x16 mm
38	Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 200x10 mm
39	Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 150x10 mm
40	Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 100x10 mm
41	Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : 125 mm
42	Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : 100 mm
43	Providing and fixing oxidised M.S. hasp and staple (safety type) conforming to IS : 363 with necessary screws etc. complete : 150 mm
44	Providing and fixing bright finished brass 100 mm mortice latch with one dead bolt and a pair of lever handles of approved quality with necessary screws etc. complete.
45	Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc complete.
46	Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 250x16 mm
47	Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm
48	Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper
49	Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
50	Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: One or more coats on old work
51	Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
52	Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using flats 30x6mm for diagonal braces and central cross piece
53	Welding by gas or electric plant including transportation of plant at site etc. complete.
54	Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate
55	Cement concrete flooring 1:2:4 (1cement:2coarse sand: 4graded stoneaggregate) finished with a floating coat of neat cement, including cement slurry but excluding the cost of nosing of steps etc complete. 25 mm thick with 12.5 mm nominal size stone aggregate
56	Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete. With 2nd class teak wood beading 62X19 mm
57	Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in- Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
58	Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc., complete.
59	Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer- in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
60	Painting top of roofs with bitumen of approved quality @ 17kg per 10 sqm impregnated with a coat of coarse sand at 60 cudm per 10 sqm, including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete : With residual type petroleum bitumen of grade VG -10
61	Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.75 mm diameter
62	Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter
63	Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single tee without door 110x110x110 mm
64	Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5°75 mm bend
65	Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5° 110 mm bend
66	Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Shoe (Plain) 75 mm Shoe
67	Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Shoe (Plain) 110 mm Shoe
68	Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 75 mm
69	Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm
70	12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)
71	12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)
72	6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)
73	Neat cement punning.
74	Lettering with black Japan paint of approved brand and manufacture
75	Applying one coat of water thinnable cement primer of approved brand andmanufacture on wall surface : Water thinnable cement primer
76	Applying priming coat: With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)
77	Applying priming coat: With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works
78	Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work
79	Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding hold fasts in cement concrete blocks of size 15 x 10 x 10 cm with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground, all complete as per directions of Engineer-In-Charge. Door chowkhats
80	Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding hold fasts in cement concrete blocks of size 15 x 10 x 10 cm with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground, all complete as per directions of Engineer-In-Charge. Window chowkhats
81	Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in- Charge.
82	Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of thickness 4 mm (weight not less than 10kg/sqm)
83	Renewal of old putty of glass panes (length)
84	Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. One coat
85	Painting with synthetic enamel paint of approved brand and manufacture of requiredcolour to give an even shade : One or more coats on old work
86	Finishing walls with Acrylic Smooth exterior paint of required shade: Old work (One or more coat applied @ 0.90 ltr/10 sqm).
87	Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)
88	Demolishing brick work manually/ by mechanical means including stacking ofserviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar
89	Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below
90	Taking out doors, windows and clerestory window shutters (steel or wood) includingstacking within 50 metres lead : Of area 3 sq. metres and below
91	Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.
92	Providing and fixing white vitreous china water closet squatting pan (Indian type) : Orissa pattern W.C. pan of size 580x440 mm
93	Providing and fixing white vitreous china pedestal type (European type/ wash downtype) water closet pan.
94	Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 10 litre capacity - White
95	Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete : Black solid plastic seat with lid
96	Providing and fixing white vitreous china wash basin including making all connectionsbut excluding the cost of fittings : Flat back wash basin of size 550x400 mm
97	Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. flexible pipe 32 mm dia
98	Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. flexible pipe 40 mm dia
99	Providing and fixing 100 mm sand cast Iron grating for gully trap.
100	Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approvedquality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
101	Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.
102	Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 100 mm outlet Sand Cast Iron S&S as per IS: 1729
103	Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective heightof 88 mm, weighing not less than 190 gms.
104	Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. Kiln seasoned and chemically treated hollock wood 30 mm thick shutters
105	Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : Kiln seasoned and chemically treated hollock wood
106	Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink without drain board 610x510 mm bowl depth 200 mm
107	Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as perdirection of Engineer-in-charge, manufacturer's specification & drawing. 30 mm thick plain PVC door shutters
108	P&F aluminium sheet 24 gauge door shutters with nails etc as & who required as per instructions of EIC
109	Earth work in excavation in all kind of soil/ silt by mechanical means (hydraulic excavaror)/ manual means including dozering, trasnportation, unloading at designated place, levelling and dressing of dump sites all inclusive as per instructions of EIC. with all lifts Lead up to 50 meter
110	Carriage of material by mechanical transport including loading unloading & stacking Manure of sludge Lead 1 Km
111	Providing and fixing soil, waste and vent pipes : 100 mm dia Sand cast iron S&S pipe as per IS: 1729
112	Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 100x100x100 mm Sand cast iron S&S as per IS - 1729
113	Providing and fixing single equal plain invert branch of required degree : 100x100x100 mm Sand cast iron S&S as per iron 1729
114	Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter : 100 mm
115	Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.
116	Painting of flower pots as per instructions of EIC Earthen pots of 12\\" size with colour/terracotta
117	Painting of flower pots as per instructions of EIC Mosaic pots of 15\\" size with enamel paint of approval brand
118	Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
119	Constructing masonry Chamber 60x45x50 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for water meter complete with C.I. double flap surface box 400x200x200 mm (inside) with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand:10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5
120	Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee- sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)
121	Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding
122	Small petty water supply related works.
123	Small petty carpentary work such as small repair of doors, windows, making hole, fixing of miscellaneous fixtures etc.
124	Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge
125	Removing and uprooting of unwanted Vegetation grown over the drainage pipes, walls, chhajjas, balcony and similar locaton of building upto floor Vth level with all tools & plants required with safety precautions and making good the same with plaster including disposal of material / tree roots etc. at the required place all complete as per instruction of EIC.
126	Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)
127	Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)
128	Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight not less than10kg/sqm)
129	Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainless steel cover plate minimum 1.25 mm thickness
130	Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)
131	Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer- in-charge.Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side
132	Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms
133	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 15 mm nominal outer dia Pipes
134	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal outer dia Pipes
135	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 25 mm nominal outer dia Pipes
136	Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40 gms
137	Providing and fixing PTMT pillar cock of approved quality and colour 15 mm nominal bore, 107 mm long, weighing not less than 110 gms
138	Providing and fixing PTMT bib cock of approved quality and colour. 15mm nominal bore, 86 mm long, weighing not less than 88 gms
139	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. EXTERNAL WORK 25 mm nominal outer dia Pipes
140	Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. INTERNAL WORK - EXPOSED ON WALL15 mm dia nominal bore
141	Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. INTERNAL WORK - EXPOSED ON WALL 20 mm dia nominal bore
142	Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. INTERNAL WORK - EXPOSED ON WALL 25 mm dia nominal bore
143	Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 25 to 40 mm nominal bore
144	Providing and fixing brass bib cock of approved quality : 15 mm nominal bore
145	Providing and fixing brass stop cock of approved quality : 15 mm nominal bore
146	Providing and fixing brass stop cock of approved quality : 20 mm nominal bore
147	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwedend) : 25 mm nominal bore
148	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwedend) : 20 mm nominal bore
149	Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 15 mm nominal bore
150	Providing and fixing uplasticised PVC connection pipe with brass unions : 30 cm length 15 mm nominal bore
151	Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
152	Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore
153	Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore
154	P&F PVC cistern fittings with handle complete set as per instruction of EIC
155	Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 25 mm dia nominal bore
156	Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 40 mm dia nominal bore
157	Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 50 mm dia nominal bore
158	Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 80 mm dia nominal bore
159	Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 100 mm dia nominal bore
160	Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 150 mm dia nominal bore
161	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 40 mm nominal bore
162	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 50 mm nominal bore
163	Providing and fixing gun metal non- return valve of approved quality (screwed end) : 50 mm nominal bore Vertical
164	Providing and fixing gun metal non- return valve of approved quality (screwed end) : 80 mm nominal bore Vertical
165	Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) : 100 mm diameter Class I
166	Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) : 150 mm diameter Class I
167	Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 25 mm nominal bore
168	Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 40 mm nominal bore
169	Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 50 mm nominal bore
170	Repairing of submersible pump & motor with motor winding of submersible pump set including pump set including change of oil seal, rotor bush, oring impellers etc as required as per instruction of EIC with a guarantee period 6 months 5 HP for 7.5 HP
171	Repairing of pump & motor with motor winding of submersible pump set including pump set including change of oil seal, rotor bush, oring impellers etc as required as per instruction of EIC with a guarantee period 6 months Shaft for DSM-4
172	Repairing of pump & motor with motor winding of submersible pump set including pump set including change of oil seal, rotor bush, oring impellers etc as required as per instruction of EIC with a guarantee period 6 months Shaft for DSM-5
173	Repairing of sluice valve 50 mm to 80 mm dia
174	Repairing of sluice valve 100 mm to 125 mm dia
175	Repairing of sluice valve 150 mm dia and above
176	Repairing of shaft for motor/pump DSM 4
177	Repairing of shaft for motor/pump DSM 5
178	Repairing of impeller DSM 4
179	Repairing of impeller DSM 5
180	Repairing of motor with a warantee of 6 months including winding etc. DSM-4
181	Repairing of motor with a warantee of 6 months including winding etc. DSM-5
182	Supply, instalation, commissioning and testing of electromagnetic chemical dozing plant model -A10 capacity Milton roy make or equivalent with injuction capacity maximum 2 LPH with sufficient injuction pressure for 40 M head with starter, container 200 litrs fitting all complete including operation and maintenance for 2 years.
183	Supply of 8 mm dia C.P. Brass/ S.S. Jet with flexible tube upto 1 metre long with S.S. tringular plate for Eureopean type W.C
184	Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D.plastic ball. 25 mm nominal bore, 152mm long, weighing not less than 440 gms
185	Providing and fixing PTMT angle stop cock 15 mm nominal bore, weighing not less than 85 gms
186	Providing and fixing PTMT stop cock of approved quality and colour.15 mm nominal bore, 86 mm long, weighing not less than 88 gms
187	Providing and fixing PTMT stop cock of approved quality and colour. 20 mm nominal bore, 89 mm long, weighing not less than 88 gms
188	Providing and fixing PTMT stop cock of approved quality and colour. Concealed stop cock, 15 mm nominal bore, 108 mm long, weighing not less than 108 gms
189	Providing and fixing PTMT 15 mm Urinal spreader size 95x69x100 mm with 1/2\\" BSP thread and shapes, weighing not less than 60 gms.
190	Providing and fixing PTMT extension nipple for water tank pipe,fittings of approved quality and colour.20 mm nominal bore, weighing not less than 40 gms
191	Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour. 25mm nominal bore, weighing not less than 62 gms
192	Cleaning of Surface drain including disposal of muck/sludge through trolley or other arrangement to a specified place (in no case it shall be kept on drain banks) within a lead of 1Km complete with all tools & tackles as per instruction of EIC Up to 300mm wide
193	Cleaning of Surface drain including disposal of muck/sludge through trolley or other arrangement to a specified place (in no case it shall be kept on drain banks) within a lead of 1Km complete with all tools & tackles as per instruction of EIC Above 300 mm & up to 600 mm wide
194	Brooming & Cleaning of all roads in colony and within the premises of service building and other place as required with all tools & tackles and stacking the garbage at specified place as per instruction of EIC
195	Cleaning of all types of roof including removal of dry leaves, weeding and cleaning dram holes, brooming etc. all complete with tools & tackles and stacking the garbage at specified place as per instruction of EIC.
196	Cleaning, mopping & washing of floor of public buildings other places neatly with detergents, bleaching power etc. all complete with tools, tackles and consumable to make the floor clean & hygienic as per instruction of EIC.
197	Cleaning of door Sutter, window shutters including chowkhats, window grills glass panes cobwebs etc. of service/community buildings with necessary detergents, chemical etc. complete as per instruction of EIC.
198	Cleaning of toilet (floor area upto 8 sq.m ) including cleaning of dado skirting w/c pan (Indian type/Western type) wash basins, urinals , glass shelves mirror and other fitting if any for ‘C’ type or equivalent qtrs including any other wash basin out side the toilet by hand dusting and cleaning with shop solution acid deodorants phenyl etc. to make the toilet clean and hygienic all complete with tools tackles & Consumables as per instruction of EIC
199	Cleaning of toilet (floor area upto 10 sq.m ) including cleaning of dado skirting w/c pan (Indian type/Western type) wash basins, urinals , glass shelves mirror and other fitting if any for ‘D’ type or equivalent qtrs including any other wash basin out side the toilet by & dusting and cleaning with shop solution acid deodorants phenyl etc. To make the toilet clean and hygienic all complete with tools tackles & Consumables as per instruction of EIC
200	Disposal of dead animal including transportation to the specifiedplace, making earth pit, disposal of dead animal into with adequate quantity of salt, lime bleaching powder etc. and refilling the with earth all complete with tools, tackles and consumables as per instruction of EIC Big animal (Cow, Buffalo, Ox and the like)
201	Disposal of dead animal including transportation to the specifiedplace, making earth pit, disposal of dead animal into with adequate quantity of salt, lime bleaching powder etc. and refilling the with earth all complete with tools, tackles and consumables as per instruction of EIC Small animal (Dog , cat , fox, pig, birds and the like)
202	Collection of garbage from door to door and disposal of the same through trolley or other suitable arrangement to the specified place within lead of 1 K/M including sweeping of stair case (for 1st and 2nd floor qtrs) with all tools and tackles as per instruction of EIC. Ground floor
203	Collection of garbage from door to door and disposal of the same through trolley or other suitable arrangement to the specified place within lead of 1 K/M including sweeping of stair case (for 1st and 2nd floor qtrs) with all tools and tackles as per instruction of EIC. First floor
204	Collection of garbage from door to door and disposal of the same through trolley or other suitable arrangement to the specified place within lead of 1 K/M including sweeping of stair case (for 1st and 2nd floor qtrs) with all tools and tackles as per instruction of EIC. Second floor
205	Cleaning of roof top water tank, including draining out water, cleaning, disinfecting the tank, by bleaching power etc. and washing the tanks with fresh water, writing of cleaning date with paint on the outer face of the tank all complete with tools, tackles and consumables as per instruction of EIC.
206	Cleaning of ground water reservoir including scraping of stains and muck from wall & floor and removal of muck from reservoir, disinfecting the tank by lime/bleaching power etc, and washing the tank with fresh water ,writing the cleaning date with paint on the outer surface of the tank all complete with tools, tackles and consumables as per instruction of EIC.
207	Anti-Adult Measures:General disinfection / pest control with new generation odorless, colorless insecticides which should be safe for human being and effective for all kind of house hold insects like mosquitos, house flies e.t.c. using residual spray of Deltamethrin 2.5% SC Flow (K-Othrin or approved equivalent) Insecticides should be sprayed uniformly over the surfaces of walls, ceilings e.t.c Frequency - once in 3 Months
208	Thermal Fogging-Using insecticide Deltamethrin 1.25% ULV (KingFog or approved equivalent) mixed with diesel in the ratio of 1:199, for outdoor operation of colony etc. Frequency- Monthly
209	Anti-Larvae Measures-Treatment by using Diflubenzuron 25% WP (bi-Larva or approved equivalent) solution to be spread as per instructions of EIC.Frequency- Weekly
210	Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly leveling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).
211	Supplying and stacking of good earth at site including royalty and carriage upto 5 km complete (earth measured in stacks will be reduced by 20% for payment).
212	Supplying and stacking at site dump manure from approved source, including carriage upto 5 km complete (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 20 mm
213	Rough dressing the trenched ground including breaking clods.
214	Fine dressing of the ground.
215	Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge
216	Providing Circular Cement Concrete pots of specified size, cast with cement concrete of nominal mix 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 6 mm nominal size), reinforced with 7 Nos ( 3 nos horizontal & 4 nos vertical “ U “ shape) M.S. wires of3.5 mm dia as per design, including required form work, finishing with cement punning on exposed surface, curing for specified period and stacking in required rows & height, all complete as per direction of Officer-in-charge. Top inside dia 30 cm, outer bottom dia 20 cm, total height 30 cm with wall thickness of25.4 mm
217	Providing & laying Selection no. 1 grass turf with earth 50mm to 60mm thickness on existing ground prepared with proper level and ramming with required tools wooden and than rolling the surface with light roller make the surface smoothen and light watering the same, as per direction of officer in charge
218	Topairy cutting/shapping of plant removing of cut materials, cleaning, hoeing of plants complete design hoeing of trees (Topairy) watering manure etc.(excluding the cost of material which shall be supplied by the department) and as per direction of officer incharge as per direction of officer in charge. Height of Topairy upto 120 cm.
219	Topairy cutting/shapping of plant removing of cut materials, cleaning, hoeing of plants complete design hoeing of trees (Topairy) watering manure etc.(excluding the cost of material which shall be supplied by the department) and as per direction of officer incharge as per direction of officer in charge. Height of Topairy above 120 cm.
220	Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, hedge, flower beds, foliages, creepers etc. including hoeing,weeding pruning replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter, removal of garden waste, applying insecticide, pesticide & fertilizers(whenever required) top dressing of lawn with good earth and menure and maintenance of other garden related works as directed by office in charge (Cost of Good EarthManure,Fertilizer,Insecticide,Pesticide will be provided by the Department & lawn mover and brush cutter with fuel , other T & P material/articles shall be provided by the contractor.) Permanent office accommodation.(1Mali for 1.25Acre)
221	Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, hedge, flower beds, foliages, creepers etc. including hoeing,weeding pruning replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter , removal of garden waste, applying insecticide, pesticide & fertilizers(whenever required) top dressing of lawn with good earth and menure and maintenance of other garden related works as directed by office in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide , Pesticide will be provided by the Department & lawn mover and brush cutter with fuel , other T & P material/articles shall be provided by the contractor.) MPs accommodation and Govt. officers bungalows. (1Mali for 1.25 Acre)
222	Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, hedge, flower beds, foliages, creepers etc. including hoeing,weeding pruning replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter , removal of garden waste, applying insecticide, pesticide & fertilizers(whenever required) top dressing of lawn with good earth and menure and maintenance of other garden related works as directed by office in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide , Pesticide will be provided by the Department & lawn mover and brush cutter with fuel , other T & P material/articles shall be provided by the contractor.) Play grounds / Public parks Play grounds / Public parks (1Mali for 2.00Acre).
223	Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, hedge, flower beds, foliages, creepers etc. including hoeing,weeding pruning replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter , removal of garden waste, applying insecticide, pesticide & fertilizers(whenever required) top dressing of lawn with good earth and menure and maintenance of other garden related works as directed by office in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide , Pesticide will be provided by the Department & lawn mover and brush cutter with fuel , other T & P material/articles shall be provided by the contractor.) Open spaces(1Mali for 3.00Acre).
224	Maintenance of Potted Plants at Nursery in Earthen pot including resetting/ displaying at Nursery, including watering, weeding, hoeing, colouring, transplanting the damaged pots and disposal of generated garbage at specified place as per direction of officer-in- charge. (Good earth, manure, fertilizer, insecticide & pesticide shall be provided by the department) (For Earthen pot 2000 Nos)
225	Maintenance of potted plant Earthen pot in displayed at ground floor only in bungalow,office complex including application of good earth, manure, insecticide, pesticide and fertilizer, removing of dry parts by pruning, cleaning dry leaves and displaying in appropriate place and replacement of broken pots coloring of pots and change of location of pots and replacing with fresh plants as and when required ( Materials shall be provided by the department) as per direction of officer in charge (For Earthen pot 750 Nos) Per Month
226	Maintenance of potted plants Cement pots at ground floor in flats and ground floor bungalow,office complex including application of good earth, manure, insecticide, pesticide and fertilizer, removing of dry parts by pruning, cleaning dry leaves and displaying in appropriate place and replacement of broken pots coloring of pots and change of location of pots and replacing with fresh plants as and when required (Materials shall be provided by the department) as per direction of officer in charge (For of Cement pots 300 Nos)
227	Planting different varieties of sampling plants including making earth pits, mixing of earth & manure (cost of earth & manure shall be paid separately) etc. all complete with tools & plants as per instruction of EIC On Ground
228	Planting different varieties of sampling plants including making earth pits, mixing of earth & manure (cost of earth & manure shall be paid separately) etc. all complete with tools & plants as per instruction of EIC In Pots
229	Up keeping & maintenance of dispensary in all respect by engaging 1 no man power per day
230	Lifting/lowering of submersible pump, motor including- providing joint kit threading of a pipe/ joint welding whenever required complete as per instructions of EIC (lifting and lowering to be treated as one time job) by deploying 7 nos. of labours. If no. of labours deployed are less, then twice the min. wages will be deducted against such lesser no. of labour.
231	Operation, Maintenance and guarding of submersible pumps and main pipe line (external) including earth cuttig, refilling the excavated earth making joint leakage proof by m-seal, putty, rubber tube etc. and transportation of welding plant wherever required (m-seal and welding paid seperately) maintenance tools and plants shall be arranged by contractor, all external water supply, colony, mines, CHP, regional store, railway siding morwa etc all complete by deploying 14 nos. of labours. If no. of labours deployed are less, then twice the min. wages will be deducted against such lesser no. of labour.
232	Maintenance guarding of pump motor stage and ground by deploying 3 labours per day (contractor will be penalized by deducting double rate for less deployment of labour)
233	Day to day operation and Maintenance of plant and dozing of liquid chlorine whenever required and testing of water on consumers end including labour, T&P etc. All complete as per instruction of EIC.
234	Facility Manager for heading the entire facility team of Office and Residential Complex and Single point of contact & overall in charge of FM On-site Operations and reporting to engineer-incharge or his representative.
235	Facility Manager (Technical) for supporting Critical Services Operations & reporting to Facility Manager. (2 no.s Facility Manager per day)
236	Supply of lime at site
237	Supplying and stacking at site. Moorum
238	Supply of GI Elbow 15 mm
239	Supply of GI Elbow 20 mm
240	Supply of GI Elbow 25 mm
241	Supply of GI Socket 15 mm
242	Supply of GI Socket 20 mm
243	Supply of GI Socket 25 mm
244	Supply of GI Tee 15 mm
245	Supply of GI Tee 20 mm
246	Supply of GI Tee 25 mm
247	Supply of GI Plug 25 mm
248	Supply of PVC water tank cover
249	Supply of GI Nipple 15 mm
250	Supply of GI Nipple 20 mm
251	Supply of GI Nipple 25 mm
252	Supply of CP waste jally 40 mm
253	Supply of GI union 15 mm
254	Supply of GI union 20 mm
255	Supply of GI union 25 mm
256	Supply of 100% biodegradable garbage (camy bags ) for biodegradable waste as per required size and color
257	Supply of chemical material Phenyl liquid
258	Supply of chemical material Toilet air freshner (odonil or equivalent)
259	Supply of chemical material Sanitary toilet cleaner( Harpic or equivalent)
260	Supply of chemical material Hanwash refill
261	Supply of chemical material Phenyl ball
262	Supply of different varieties of saplings & plants Dehaliya
263	Supply of different varieties of saplings & plants Guldawadi(HiB)
264	Supply of different varieties of saplings & plants Marigold
265	Supply of different varieties of saplings & plants Pansy(HiB)
266	Supply of different varieties of saplings & plants Saviya(HiB)
267	Supply of different varieties of saplings & plants Acrocarya (10\\" to 12\\")
268	Supply of different varieties of saplings & plants Cycus (2 years)
269	Supply of different varieties of saplings & plants Rose
270	Supply of different varieties of saplings & plants Caroten(Duck foot)
271	Supply of different varieties of saplings & plants Caroten(Ordinary)
272	Supply of different varieties of saplings & plants Caroten(Baby)
273	Supply of different varieties of saplings & plants Arica Palam (3 to 4 sticks size 3\\" to 4\\")
274	Supply of different varieties of saplings & plants China palm
275	Supply of different varieties of saplings & plants Silver star
276	Supply of different varieties of saplings & plants Pansutia
277	Supply of various varieties of seeds of seasonal flowers & vegetables Supply of good quality of seeds of flower (ordinary)
278	Supply of various varieties of seeds of seasonal flowers & vegetables Supply of good quality of seeds of flower (Hybrid)
279	Supply at site good quality pots Earthen pots of 12\\" size
280	Supply of fertilizer insecticide and pesticide DAP
281	Supply of fertilizer insecticide and pesticide Urea
282	Supply of fertilizer insecticide and pesticide Bonemeal
283	Supply of fertilizer insecticide and pesticide Rose Mixture
284	Supply of fertilizer insecticide and pesticide Neem Cake
285	Supply of fertilizer insecticide and pesticide Melathion
286	Supply of fertilizer insecticide and pesticide Roger 30%
287	Supply of fertilizer insecticide and pesticide Sarso Khalli
288	Providing steel spindle with check nut. 50mm dia
289	Providing steel spindle with check nut. 80mm dia
290	Providing steel spindle with check nut. 100mm dia
291	Providing steel spindle with check nut. 150 mm dia
292	Providing Gland packing
293	Providing M. seal
294	Providing coupling bush
295	Providing coupling bolt
296	Coupling of DSM-4
297	Coupling of DSM-5
298	Providing GI socket 50 mm dia size long thread of heavy duty
299	Providing grease of standard quality for pump and motor.
300	Providing rubber gasket.
301	Providing GI flange of heavy quality ( heavy duty). 50 mm dia size
302	Providing GI flange of heavy quality ( heavy duty).80 mm dia size
303	Providing GI flange of heavy quality ( heavy duty). 100 mm dia size
304	Providing CI sluice valve 50 mm dia
305	Providing CI sluice valve 80 mm dia
306	Providing GI foot valve of 125 mm dia
307	Providing GI tee 25 mm dia
308	Providing GI tee 50 mm dia
309	Providing GI tee 80 mm dia
310	Providing GI socket 25 mm dia
311	Providing GI socket 80 mm dia
312	Providing GI socket100 mm dia
313	Providing GI reducer 50*25 mm
314	Providing GI reducer 80*25 mm
315	Providing GI reducer 100*25 mm
316	Supply of GI bend 50 mm dia
317	Supply of GI bend 80 mm dia
318	Supply of GI bend 100 mm dia
319	Supply of GI nipple (50 mm long ) 25 mm dia
320	Supply of GI nipple (50 mm long ) 40 mm dia
321	Supply of GI nipple (50 mm long ) 50 mm dia
322	Providing GI elbow 25 mm dia
323	Providing GI elbow 40 mm dia
324	Providing GI elbow 50 mm dia
325	Providing Copper cable 4 sq. mm
326	Providing starter panel for 7.5 hp submersible motor pump
327	Key for motor/pump
328	Providing starter panel coil
329	Providing GI flange 80 mm dia
330	Providing GI flange 100 mm dia
331	Providing GI flange 150 mm dia
332	Providing NRV ( Vertical ) 100 mm size
333	Providing housing DSM-5
334	Supply and stacking of sand at site
335	Providing liquid chlorine solution with sodium Hypochloride base formulated confirming to IS-11673-1992-G-1 and 10500 -1991 for treatment of potable water
336	Supply of bleaching powder
337	Supply of UPVC Fitting UPVC Coupler 50mm
338	Supply of UPVC Fitting UPVC Coupler 25mm
339	Supply of UPVC Fitting UPVC pipe 50mm dia
340	Supply of UPVC Fitting UPVC pipe 25mm dia
341	Supply of UPVC Fitting UPVC ELBOW 25mm
342	Supply of UPVC Fitting UPVC ELBOW 50mm
343	Supply of UPVC Fitting UPVC end cap 25mm dia
344	Supply of CPVC Fitting Coupling 20mm dia
345	Supply of CPVC Fitting Coupling 25mm dia
346	Annual Maintenance contract for day to day No power, fan servicing and maintenance and other miscellaneous work at residential quarters and service buildings with the help of 03 no skilled and 03 no unskilled man power
347	Breakdown Maintenance/ routine maintenance of LT/HT overhead line, street light, handling of HT/LT cables etc. work as and when required or as instructed by in-charge township. With the help from 02 skilled and 02 no unskilled manpower
348	Re winding of ceiling fan with super enameled copper wire as per existing gauge of different size and make after cleaning of damaged windings including greasing/ checking etc of ceiling fan/ wall mounted fan/ exhaust fan of different size installed at township (including transporting, cleaning & assembling)
349	Supply of ceiling fan bearing of required size (6201 2Z, 6202-2Z, 6203-2Z etc)(material cost only) Make SKF/ NTN/ NBC etc.
350	Supply of clamp of different size suitable to existing/ rewinded fan of different size and make
351	Supply of GI nut bolt washer as per requirement
352	Supply of flexible wire 23/76 SWG copper
353	Fuse wire 14-20 SWG
354	Supply of ML4 power contactor
355	Supply and installation of Heating element 2 KW
356	Supply of PVC casing n capping 20 x 12 mm ISI marked (Branded make)
357	Supply and fixing of following sizes of medium class PVC conduit/casing caping along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required 25mm
358	Piano type switch 5A/6A(Arkaylite/Anchor/Legrand/Havells or its equivalent ISI marked)
359	Piano type socket 5A/6A(Arkaylite/Anchor/Legrand/Havells or its equivalent ISI marked)
360	Piano type switch 15/16A (Arkaylite/Anchor/Legrand/Havells or its equivalent ISI marked)
361	Piano type socket 15/16A (Arkaylite/Anchor/Legrand/Havells or its equivalent ISI marked)
362	Supply and fixing of PVC battan/angle holder(Arkaylite/Anchor/Legrand/Havells or its equivalent ISI marked)
363	MCB 5-32A single pole with box (Standard Legrand/Havells or its equivalent ISI marked)
364	Fan capacitor 2.5mfd(ISI marked)
365	Plug Top 5A, 230V
366	Plug Top 15A, 230V
367	Call bell
368	PVC single core Al. 2.5 sq.mm. cable
369	PVC single core Copper 1.5 sq.mm. cable
370	PVC single core Copper 4.00 sq.mm. cable
371	Digital timer switch
372	Bell push switch
373	Running maintenance and overhauling of 150 nos. 1.5/2 tone ACs for 214 days (1 skilled + 1 semi-skilled)
374	Shifting, installation, commissioning of 1.5/ 2 tone window/split AC’s as per requirement and direction of EIC.
375	Supply of freon gas R22/R32/R134A/R410 for replacement
376	Repairing/Rewinding of fan motor of AC
377	Supply of running capacitor 5 to 36 mfd for replacement
378	Supply of running capacitor 45 to 50 mfd for replacement
379	Supply of starting capacitor 10 to 25 mfd for replacement
380	Supply of fan/blower motor condensor for 4 to 6 mfd for replacement
381	Supply of AC remote panel assembly with remote for replacement
382	Providing and fixing of new hermetically sealed compatible compressor for 1.5/2 Ton window/Split type AC
383	Toshiba make Indoor PCB kit
384	Toshiba make outdoor PCB kit
385	Outdoor Fan Blade
386	Wiring of light point/ fan point/exhaust fan point/call bell point/ with 1.5 sqmm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit with piano type switch,phenolic laminated sheet, suitable size switch box and earthing the point 1.5 sq mm FRLS PVC insulated copper conductor single core etc. as required (ISI Marked)
387	Wiring of light point/ fan point/exhaust fan point/call bell point/ with 1.5 sum FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit with modular switch, modular plate, suitable size switch box and earthing the point 1.5 sq mm FRLS PVC insulated copper conductor single core etc. as required (ISI Marked)
388	Wiring for circuit/submain wiring alongwith earth wire with the size 2 x 2.5 sqmm + 1 x 2.5 sqmm (earth wire) FRLS PVC insulated copper conductor,single core cable in surface/recessed medium class PVC conduit as required (ISI Marked)
389	Supplying and drawing of FRLS PVC insulated copper conducter size- 3 x 6.00 sqmm, single core cable in existing surface/recessed steel/PVC conduit as required (ISI marked)
390	Wiring for circuit/submain wiring alongwith earth wire with the size 4 x 10 sqmm + 2 x 6 sqmm (earth wire) FRLS PVC insulated copper conductor,single core cable in surface/recessed medium class PVC conduit as required (ISI Marked)
391	Wiring for circuit/submain wiring alongwith earth wire with the size 4 x 16 sqmm + 2 x 6 sqmm (earth wire) FRLS PVC insulated copper conductor,single core cable in surface/recessed medium class PVC conduit as required (ISI Marked)
392	Cleaning of 33KV Substation, distribution substations, and other locations related to electrical installations at Block-B Colony with the help of 02 nos of unskilled manpower/day.(Cleaning work related tools will be provided by Contractor)
393	6 sq mm ISI marked, FRLS PVC insulated,single core copper conductor cable.
394	250mm x 300mm x 100 mm deep metal box
395	Stepped type modular fan regulator (2 module)
396	S.P. 5/6 A, one way modular switch ISI marked
397	S.P. 15/16 A, one way modular switch ISI marked
398	3 pin, 5/6 A, modular socket outlet ISI marked
399	6 pin, 15/16 A, modular socket outlet ISI marked
400	4 pole MCCB, 250A, 50KA, (ISI marked)
401	4 pole MCCB, 630A, 50KA (ISI marked)
402	3 pole MCCB, 150A, 16KA (ISI marked)
403	Cotton waste, cleaning cloths etc
404	20 mm dia, ISI marked, PVC conduit
405	25 mm dia, ISI marked, PVC conduit
406	20 mm PVC bends
407	25 mm PVC bends
408	20 mm PVC couplers
409	25 mm PVC couplers
410	Bush Bearing for ceiling fan
411	Flexible PVC Conduit Pipe
412	HT tape ( 10 Mtr in roll)
413	Supply of hackshaw blade (L- 300mm, W- 12.5 mm)
414	Nail clip ( Flat and round)( 100 qty per packet)
415	PVC Empire tape ( 20 mtr in roll, width- 19 mm)
416	PVC steel grip tape 1.70 cm x 6 mtr (pack of 30 rolls)
417	Switch board box with frame plate, 6 module (Size- 210 mm x 75mm x 50mm)(ISI marked)
418	Switch board box with frame plate (Size- 250 mm x 200mm x 100mm)(ISI marked)
419	Switch board box with frame plate (Size- 100mm x 75mm x 50mm)(ISI marked)
420	Total impact of GST for the purpose of CTC Please Enable Macros to View BoQ information

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents

Also Visit

Tenders

Madhya Pradesh Tenders

Services Tenders

Hospitality Related Services Tenders

Facility Management Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Annual Operation, Maintenance And Providing Civil & Electrical Maintenance (Including Facility Management Services) For Office And Residential Complex At Block-B Area For 2 Years., Singrauli-Madhya Pradesh

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Annual Operation, Maintenance And Providing Civil & Electrical Maintenance (Including Facility Management Services) For Office And Residential Complex At Block-B Area For 2 Years., Singrauli-Madhya Pradesh

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us