|
| 1 | M & L for cement concrete M10 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs, slab staging for water tanks, filling of pressed steel door frame, fixing of hold fasts and the like including weathering, slightly rounded or chamfered angles and throating including necessary formworks complete all as specified and as directed. |
| 2 | M & L for brick work with sub class 'B' bricks, non-modular sizes as per IS 1077: 1992, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6 complete all as specified and as directed. |
| 3 | M & L for 35 mm thick, timber species of super group and durability class I as per IS 12896: 1990 and first grade as per IS 1003 (Part-1): 2003, factory made, glazed and skeleton shutters, open rebated and prepared to receive glass, wire gauze, etc. (without sash bar), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part-I section 8 Clause 8.24 (a) complete all as specified and as directed. |
| 4 | S & F flush door shutters, 30 mm thick, solid core of block boards construction, MR grade, commercial type with stiles, rails and lipping of timber as given in Group 2A and Group 2B of Annex B of IS 2202 (Part 1): 1999, both sides face panels of plywood as per IS 710: 2010, internally lipped complete all as specified and as directed. |
| 5 | Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 sqm each complete all as specified and as directed. |
| 6 | Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 sqm but not exceeding 4.00 sqm each complete all as specified and as directed. |
| 7 | Taking down and refixing in same opening wooden door shutter area exceeding 1.00 but not exceeding 2.00 sqm each complete all as specified and as directed. |
| 8 | Taking down wooden door shutter area exceeding 1.00 but not exceeding 2.00 sqm each complete all as specified and as directed. |
| 9 | S & F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 mm X 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm², modules of elasticity 900 N/mm² and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with mild steel hold fast/ lugs/stainless steel dash fasteners of required dia and length complete all as specified and as directed. (mild steel hold fast/ lugs or stainless steel dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5 mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 10 | S & F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 mm X 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm², modules of elasticity 900 N/mm² and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with mild steel hold fast/ lugs/stainless steel dash fasteners of required dia and length complete all as specified and as directed. (mild steel hold fast/ lugs or stainless steel dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5 mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 11 | S & F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 mm X 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm², modules of elasticity 900 N/mm² and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with mild steel hold fast/ lugs/stainless steel dash fasteners of required dia and length complete all as specified and as directed. (mild steel hold fast/ lugs or stainless steel dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5 mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 12 | S & F factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30 mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm², modulus of elasticity 850 N/mm² and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk stainless steel screws complete all as specified and as directed. (Note: stainless steel butt hinges and necessary stainless steel screws shall be paid separately.) |
| 13 | S & F factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35 mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm², modulus of elasticity 850 N/mm² and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk stainless steel screws complete all as specified and as directed. (Note: stainless steel butt hinges and necessary stainless steel screws shall be paid separately.) |
| 14 | Providing and fixing factory made uPVC white colour fixed window (Area not exceeding 1.00 sqm each) made of extruded profiles with wall thickness of 2.3 mm ±0.2 mm. Window profile with hollow section with multi chamber. Frame (60 mm X 58 mm). T profile (One vertical length in between two shutters) (60 mm X 74 mm). Glazing bead (35 mm X 20 mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware, EPDM gasket. 1.2 mm ± 0.2 mm thick, galvanized steel Frame (28 mm X 21.5 mm), T profile (27 mm X 17 mm) to be inserted in required profile, frame will be fixed to the wall with 8 mm X 100 mm long fasteners- 5 mm thick glazing with selected quality glass complete all as specified and as directed. Note: The unit rate quoted by the contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose. |
| 15 | M&L Providing and fixing factory made uPVC white colour casement (Openable) window /ventilator of Area not exceeding 1.00 sqm each made of extruded profiles with wall thickness of 2.3mm ( + – 0.2mm).Window profile with hollow section with multi chamber, frame (60mm x 58mm), sash (60mm x 73mm), T profile (One vertical length in between two shutters) (60mm x 74mm), Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 +– 0.2mm thick, galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27.5mm). T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100mm long fasteners. Hardware: [casement handle made of zinc alloyed (white powder coated), Butt Hinges of 'zinc alloyed (white powder coated), transmission gear made of mild steel with multi point locking system] and 5mm thick glazing with selected quality glass. (Note: The unit rate quoted by contractor excludes cost of glass and Wire mesh and includes all other connected accessories. Net opening will be measured for payment purpose.) |
| 16 | Providing and fixing factory-made uPVC white colour sliding window area not exceeding 2.00 sqm each, three track made of extruded profiles with wall thickness of 2.3 mm (±0.2 mm), window profile with hollow section with multi chamber. frame (88 mm X 52 mm), sliding sash (42 mm X 67 mm), sliding mesh sash (42 mm X 57 mm), sliding interlock (one vertical length in each shutter) (45.5 mm X 28 mm), glazing bead (24.5 mm X 16 mm) will be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2 mm ± 0.2 mm thick galvanised steel frame (30 mm X 18 mm) 2 Nos, sliding sash (30 mm X 18 mm), sliding mesh sash (26 mm X 10 mm) profile to be inserted in required profile, frame will be fixed to the wall with 8 mm X 100 mm long fasteners, hardware [touch lock of zinc alloyed (white powder coated), steel roller system, stainless steel wire cloth 0.63 mm nominal dia of wire and average width of aperture 1.40 mm and required accessories complete all as specified and as directed. Note: -The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose. |
| 17 | S & F aluminium barrel tower bolts with barrel and bolt of extruded sections of aluminium alloys, 200 mm long, dia of bolt 12 mm, anodized finish not be less than Grade AC 10 of IS 1868 : 1996 with transparent anodic film complete all as specified and as directed. |
| 18 | M&L for Complete removal of existing treatment of any description on old wall surfaces of any description, preparation of surfaces by mechanized sander having suction vacuum bag using smart periodical methodology complete all as specified and applying two coats @ 5 sqm per liter per two coats including a coat of exterior primer * 11 sqm/ltr/one coat of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior emulsion paint of required shade of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed. Cost for the same for scaffolding for plastering & painting etc is included in the rates quoted by the contractor. |
| 19 | M&L for preparation of new surfaces by mechanized sander having suction vacuum bag using smart periodical methodology complete all as specified. Providing and applying plaster of paris putty of 1 to 2 mm thickness over plastered surface to prepare the surface even and smooth and applying two coats @ 5 sqm per liter per two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior emulsion paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed.Note : Before applying painting (OBD & Exterior emulsion) in bldgs a sample patch of size 1 mtr x 1 mtr to be done for approval of GE. Painting should be done by using painting roller, mechanically method and as per manufacturer's instructions. Cost for the same for scaffolding for plastering & painting etc is included in the rates quoted by the contractor. |
| 20 | Complete removal of existing treatment on Old Internal wall surfaces of any description, preparation of surface by Mechanized sander having suction vacuum Bag using Smart periodical methodology, complete all as specified and applying the following :-(a) M&L for wall care putty a coat of 1.0-2.0 mm thick layer on wall surface and smoothening the surface with sand papers / Mechanized sanding etc preparatory to paint as directed complete all as specified.(b) M&L for two coat of acrylic emulsion Paint of approved tint over a coat of primer on old prepared surface by using Airless spray/Roller complete all as specified.Note:- Contractor may use manual scraping tools for complete removal and surface preparation with prior approval of Engr-in-Charge in case of using of Mechanical equipment are not possible. |
| 21 | Preparation of New plastered Internal wall surface complete all as specified complete all as specified and applying the following:-(a) M&L wall care putty a coat of 1.0 - 2.0 mm thick layer on wall surface and smoothening the surface with sand papers / Mechanized sanding etc prepatory to paint as directed complete all as specified.(b) M&L two coat of acrylic emulsion paint over a coat of chalk whitening priming by using Airless spray/Roller complete all as specified.Note:- Contractor may use manual scraping tools for complete removal and surface preparation with prior approval of Engr-in-Charge in case of using of Mechanical equipment are not possible. |
| 22 | S&F for Prepainted pressed steel frames of size 75 X 60 mm for Cubboard frames with one or more rebates including necessary supply and fixing lugs hinges, locks strike plate etc(thickness of sheet shall be 1.25mm) and making good the wall with plaster in CM 1:6 complete all as specified and as directed. |
| 23 | M&L Pressed steel shutter for cupboard with sheet thickness not less than 1.2 mm made to shape with and including locking arrangement, handles, hinges and one shop coat painting complete all as specified and directed. |
| 24 | Taking down of old rolling shutters all as specified and as directed. |
| 25 | S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 02 Nos in each door, 03 Nos hinges in each leaf, one aluminium sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet or one mortice lock in each door, aluminium snap beading, screws, including taking down of old shutter of any description and any size complete all as specified and as directed. |
| 26 | S&F 12mm thick toughened glass door/partition of approved colour , design and logo (if required any type) side opening type or sliding type , single shutter/double shutter/triple shutter fixed type etc. with complete fittings of approved make including pivot hinge, stainless steel chromium plated 450mm to 600mm length handle fancy type (for doors) , locking device with duplicate key, spenders partitions fixing rods/clits, two track or three track channel, rollers as required and other fittings if required etc. and connecting jobs like tile cutting, demolition PCC, tiling, marble , plastering and painting etc. to make site good complete including taking down old door of any pattern and any size. Note: - All the fittings will be approved by GE/Engineer-in-charge before work started) complete all as specified and as directed. |
| 27 | Supply and fixing stainless steel curtain rod 25mm dia, wall thickness of pipe not less than 16 gauge and grade SS 304, including brackets and pair of decorated end knobs (finials), stop roller etc. as per site requirement, fixed to wall with fixing accessories, including taking down old existing curtain rods any type or condition complete all as specified. |
| 28 | Material and labour for providing glazed ceramic coloured tiles in vertical surface (approved any shade in any pattern of light & dark/highlighters tiles etc. as approved) area of each tile exceeding 0.06 Sqm and not exceeding 0.18 Sqm having thickness 7-8 mm thick, Premium quality having water absorption should be between 10% to 20%, straight edge, stain free, glossy finish, laid as on vertical surfaces such as in skirting/dado etc.,, set and jointed using type-2 adhesive (thin bed) confirming to IS-15477:2019, fixed the tile using spacer 3mm or as per manufacturer’s instruction and joint filled with epoxy grout matching with the colour of tiles including necessary cutting as per site requirement, complete all as specified and as directed. |
| 29 | S & F aluminium alloy sliding door bolts with hasp, staple and fixing clips of sheets, or extruded sections and fixing bolts and sliding bolts of extruded sections of aluminium alloy, 250 mm long, anodized to a bright natural, mat finish not be less than Grade AC 10 of IS 1868 : 1996 complete all as specified and as directed. |
| 30 | S & F in repairs brass door spring of rat tail type of size 300 mm, bright finish including roller and roller plate complete all as specified and as directed. |
| 31 | S & F extruded aluminium alloy handle, fabricated type, 150 mm size, anodized to a bright natural, mat finish not be less than Grade AC 10 of IS 1868 : 1996 complete all as specified and as directed. |
| 32 | S & F mortice lock, vertical type, cast brass, 4 levers, vertical type, 100 mm size, finished smooth fixed in position complete all as specified and as directed. |
| 33 | S & F exposed type hydraulically regulated door closers, universal closer, bottle type (type A), Designation No. 3, suitable for 61 kg to 80 kg mass of doors & 851 mm to 1000 mm width of door, aluminium alloy non porous body and black plate, aluminium alloy piston or pack piston/ pillion, anodized finish not be less than Grade AC 15 of IS 1868 : 1996 with transparent anodic film as per IS 3564: 1995 complete all as specified and as directed. |
| 34 | S & F galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised steel wire staples complete all as specified and as directed. |
| 35 | S & F in repairs galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised steel wire staples complete all as specified and as directed. |
| 36 | S & F double action concealed type floor springs (hydraulically regulated) made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel top cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and as directed. |
| 37 | S & F hot rolled medium and high tensile structural steel of grade E165 as per IS 15911: 2010 as in framed work such as grills, grating, etc., with ends of bars of shouldered and/or riveted, or forged into spikes, framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework water tanks and similar work complete all as specified and as directed. |
| 38 | S&F steel rolling shutters 1.25mm thick lathing, with ball bearing as specified including top cover, anchoring rod, hasp and staple, guide channel and one shop coat of primer, gear operated type with bevel gear box and crank handle, erected in position as indicated complete all as specified and as directed. |
| 39 | S&F safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and as directed. |
| 40 | S & F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed. |
| 41 | S & F steel ventilators with top hung shutters including hinges, steel peg stay complete all as specified and as directed. |
| 42 | S & F pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.25 mm thickness, size 105 mm X 60 mm, Profile B, single rebate including hinges, mortar guards, lock strike plate, shock absorbers complete all as specified and as directed. |
| 43 | S & F pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.25 mm thickness, size 125 mm X 60 mm, Profile D, single or double rebate including hinges, mortar guards, lock strike plate, shock absorbers complete all as specified and as directed. |
| 44 | S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (fixed portion) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gap at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/paneling, CP brass/stainless steel screws, all complete as per architectural drawings and directions of Engineer-in-charge. |
| 45 | S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS:1868 with minimum anodic coating of grade AC 15 of approved design and pattern with approved standard section and fixed to existing window frame with cp brass and stainless steel screw @ 200mm centre to centre including cutting the grill to proper opening size for fixing and operation of handle and fixing approved anodised aluminium standard section around the opening all complete all as specified and as directed by Engineer-in-charge.. |
| 46 | S & F prelaminated particle board (decorative lamination on one side and other side balancing lamination), 20 mm thick, grade I or II & type II (Designation PLB-12 or PLB-22), made out of medium density particle board (flat pressed-three layer or multilayer and graded (grade I or grade II), bonded with BWR adhesive), fixed with screws to timber/ steel frame work for horizontal applications as in tabletops, counter, furniture tops, etc. complete all as specified and as directed. |
| 47 | M & L for 20 mm thick Granite (of any type) tiles machine cut, in skirting/dado laid over and including 10 mm thick backing in cement mortar 1:4 cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and as directed. |
| 48 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises |
| 49 | Material and labour for plastering 15 mm thick on fair faces of brick work or concrete surfaces (on vertical surfaces) in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified and as directed. |
| 50 | Material and labour for plastering 15 mm thick on fair faces of brick work or concrete surfaces (on vertical surfaces) in cement mortar 1:6 finished even and fair complete all as specified and as directed. |
| 51 | Taking down cement plaster on stone/brick/concrete surfaces including racking out joint, hacking for key, scrubbing down with water complete all as specified and as directed. |
| 52 | Supply & fix sheet glass, ordinary quality, 3 mm thick and glazed with oil putty or fixed with beads in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed. |
| 53 | Supply & fix sheet glass, ordinary quality, 4 mm thick and glazed with oil putty or fixed with beads in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed. |
| 54 | Supply & fix sheet glass, ordinary quality, 4.8 mm thick and glazed with oil putty or fixed with beads in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed. |
| 55 | S & F 4 mm thick figured glass, pin head type and glazing with oil putty or fixed with beads in square not exceeding 0.5 sqm in each pane complete all as specified and as directed. |
| 56 | M & L for preparation of new or previously untreated wood or wooden surfaces, of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed. |
| 57 | M & L for preparation of old painted wood or wooden surfaces, of any description, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed. |
| 58 | Preparation of newly or previously untreated steel surface of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed. |
| 59 | Preparation of old or previously untreated steel surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed. |
| 60 | Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc. complete all as specified and as directed. |
| 61 | Material and labour for providing glazed ceramic coloured tiles (approved any shade in any pattern of light & dark/highlighters tiles etc. as approved) area of each tile exceeding 0.06 Sqm and not exceeding 0.18 Sqm having thickness 7-8 mm thick, Premium quality having water absorption should be between 10% to 20%, straight edge, stain free, glossy finish, laid in floors and skirting etc.,, set and jointed using type-2 adhesive (thin bed) confirming to IS-15477:2019, fixed the tile using spacer 3mm or as per manufacturer’s instruction and joint filled with epoxy grout matching with the colour of tiles including necessary cutting as per site requirement, complete all as specified and as directed. Note: Screed bed shall be measured and paid separately under respective item of BOQ Please Enable Macros to View BoQ information |
