|
| 1 | Civil Work |
| 2 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. |
| 3 | Glazed vitrified floor tiles polished finish of size |
| 4 | Size of Tile 600 x 600 mm |
| 5 | Size of Tile 600 x 1200 mm |
| 6 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : |
| 7 | 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) |
| 8 | 12 mm cement plaster of mix : |
| 9 | 1:4 (1 cement: 4 coarse sand) |
| 10 | 15 mm cement plaster on the rough side of single or half brick wall of mix : |
| 11 | 1:4 (1 cement: 4 fine sand) |
| 12 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 13 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. |
| 14 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : |
| 15 | New work (two or more coats) over and including water thinnable priming coat with cement primer |
| 16 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 17 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : |
| 18 | One or more coats on old work |
| 19 | Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: |
| 20 | Float glass panes of nominal thickness 5 mm (weight not less than 12.5kg/sqm) |
| 21 | Hacking of CC flooring including cleaning for surface etc. complete as per direction of the Engineer-in-Charge. |
| 22 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in- harge. |
| 23 | Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 24 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge |
| 25 | In cement mortar |
| 26 | Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead. |
| 27 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 28 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. |
| 29 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: |
| 30 | Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 31 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : |
| 32 | Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 33 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main \\"T\\" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross \\"T\\" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main \\"T\\" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross \\"T\\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main \\"T\\" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with 959 SUB HEAD : 12- ROOFING galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. |
| 34 | GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece |
| 35 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : |
| 36 | Kitchen sink without drain board |
| 37 | 610x510 mm bowl depth 200 mm |
| 38 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : |
| 39 | 250x16 mm |
| 40 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 41 | 150x10 mm |
| 42 | Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete. |
| 43 | 75mm overall thickness partition with 12.5 mm thick double skin tapered edged plain Gypsum plaster board conforming to IS: 2095: (part I): 2011 (Board with BIS certification marks) |
| 44 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : |
| 45 | For fixed portion |
| 46 | Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 47 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) |
| 48 | Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 49 | Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer- in-charge. |
| 50 | Pre-laminated particle board with decorative lamination on both sides |
| 51 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): |
| 52 | With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) |
| 53 | P/F of stainless steel finish locks OPL-1 of ozone/drona or equivalent floor mounted for toughened glass fixed in bottom of the door complete in all respect and to the entire satisfaction of engineer in charge. |
| 54 | Providing and fixing steel tublar type handle set 32mm dia, 450mm long with stainless steel screws etc. complete in all respect to the entire satisfaction of engineer in charge. |
| 55 | Providing and fixing 12 mm thick fix toughened glass of approved brand and manufacture,and fixed with necessary fixutres of SS and SS screws,angles etc to the entire sarisfaction of engineer in charge. |
| 56 | Providing and Fixing Hydraulic Door set Machine for Toughened glass doors Complete of Hardwin Make |
| 57 | Providing and Fixing Frost filming on the glass doors and partition as per the given design |
| 58 | Providing and Fixing Megnetic Catcher on backside of glass doors |
| 59 | Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe including painting with anticorrosive bitumastic paint, cutting chases and making good the wall: |
| 60 | 15 mm dia nominal bore |
| 61 | 20 mm dia nominal bore |
| 62 | Providing and fixing C.P long body Bib Cock with wall flange of Make Jaquar Model or equivalaent model of approved make. |
| 63 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. |
| 64 | Cement mortar 1:4 (1 cement :4 coarse sand) |
| 65 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 66 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. |
| 67 | Granite stone slab colour black, Cherry/Ruby red |
| 68 | Area of slab over 0.50 sqm |
| 69 | Electrical work |
| 70 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 71 | Group C |
| 72 | Wiring for light point/ power plug with 2x4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated conductor single core cable for loop earthing as required |
| 73 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. |
| 74 | 2 x 1.5 sqmm + 1 x1.5 sqmm |
| 75 | 2 x 2.5 sqmm + 1 x 2.5 sqmm |
| 76 | 2 x 4 sqmm + 1 x 4 sqmm |
| 77 | 2 x 6 sqmm + 1 x 6 sqmm |
| 78 | 2 X 10 sq. mm + 1 X 6 sq. mm earth wire |
| 79 | 4X 4 sq. mm + 2 X 4 sq. mm earth wire |
| 80 | 4X 6 sq. mm + 2 X 6 sq. mm earth wire |
| 81 | Rewiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable and 1.5 sq.mm FRLS PVC insulated copper conductor single core cable as earth wire in existing surface/ recessed steel/PVC conduit including dismantling as required. |
| 82 | Group C |
| 83 | Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. |
| 84 | 3 x 1.5 sq. mm |
| 85 | 3 x 2.5 sq. mm |
| 86 | 3 x 4 sq. mm |
| 87 | 5 x 6 sq. mm |
| 88 | Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. |
| 89 | 2 Pair |
| 90 | 4 Pair |
| 91 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. |
| 92 | 20 mm |
| 93 | 25 mm |
| 94 | 32 MM |
| 95 | 40 mm |
| 96 | Supplying and fixing metal box of following sizes(nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover In front including painting etc. as required |
| 97 | 75mm x 75mm x 60mm deep |
| 98 | 150 mm x 75 mm x 60 mm deep |
| 99 | 200 mm x 150 mm x 60 mm deep |
| 100 | 250mm x 300mm x 100mm |
| 101 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. |
| 102 | 5/6 A switch |
| 103 | 15/16 A switch |
| 104 | 3 pin 5/6 A socket outlet |
| 105 | 6 pin 15/16 A socket outlet |
| 106 | Telephone socket outlet |
| 107 | Bell push |
| 108 | Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
| 109 | Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. |
| 110 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. |
| 111 | 1 or 2 Module (75mmX75mm) |
| 112 | 3 Module (100mmX75mm) |
| 113 | 4 Module (125mmX75mm) |
| 114 | 6 Module (200mmX75mm) |
| 115 | 8 Module (125mmX125mm) |
| 116 | 12 Module (200mmX150nnm) |
| 117 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. |
| 118 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. |
| 119 | Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required. |
| 120 | Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required. |
| 121 | Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. |
| 122 | 1 run of cable |
| 123 | Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 124 | Group C |
| 125 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2nos 3 pin 5/ 6 AMP Modular socket outlet and 2nos. 5/6 AMP Modular Switch, connections etc. as required |
| 126 | Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. |
| 127 | 100 A/63 A, 16 KA, TPMCCB |
| 128 | 125A, 16 KA, TPMCCB |
| 129 | 100 A/63 A, 30 KA, FPMCCB |
| 130 | 125 Amp, 36KA,FPMCCB |
| 131 | 250 Amp, 36KA,FPMCCB |
| 132 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) |
| 133 | 6 way , Double door |
| 134 | 8 way , Double door |
| 135 | 12 way , Double door |
| 136 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MOB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) |
| 137 | 4 way (4 + 12), Double door |
| 138 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MOB DB complete with connections, testing and commissioning etc. as required. |
| 139 | Single pole |
| 140 | Single pole and neutral |
| 141 | Double pole and neutral |
| 142 | Triple pole |
| 143 | Triple pole and neutral |
| 144 | Supplying and fixing single pole blanking plate in the existing MOB DB complete etc. as required. |
| 145 | Supply and fixing of TP sheet steel enclosure on surface/recess along with 16/25/32 A 415 V \\"C\\" curve TPMCB complete with connections , tedting and commissioning etc as required. |
| 146 | Supplying and fixing Cable End Box (Loose Wire Box) suitable for following single pole and neutral, sheet steel, MCB distribution board, 240 Volts, on surface/ recess, complete with testing and commissioning etc.as required. |
| 147 | For 10 way, Double door SPN MCBDB |
| 148 | Supplying and fixing Cable End Box (Loose Wire Box) suitable for following Triple pole and neutral, sheet steel, MCB distribution board, 415 Volts, on surface/ recess, complete with testing and commissioning etc.as required. |
| 149 | For 4way, Double door TPN MCBDB |
| 150 | Supplying and fixing Cable End Box (Loose Wire Box) suitable for triple pole and neutral, sheet steel, Vertical MCB distribution board, 415 Volts, on surface/ recess, complete with testing and commissioning etc. as required. |
| 151 | Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. |
| 152 | Earthing with GI earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.70 metre long etc. with 96kg charcoal/ coke as required |
| 153 | Supplying and laying 25mm x 5mm G.I strip at 0.50 metre below ground level as strip earth electrode , including connection/terminating with G.I nut ,bolt ,spring washer etc as required ( Jointing shall be done by overlapping and with 2 sets of G.I nut bolt & spring washers spaced at 50mm) |
| 154 | Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required. |
| 155 | Providing and laying earth connection from earth electrode with 4 mm dia Copper Wire in 15 mm dia G.I. pipe from earth electrode including connection with Copper . thimble excavation and re-filling as required. |
| 156 | Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required |
| 157 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. |
| 158 | 63 mm dia (0D-63 mm & ID-51 mm nominal) |
| 159 | Supply,erection,testing and commissioning of ceiling fans 1400mm sweep One star rating white color with copper winding but without regulator complete with aluminium blades, plastic canoples 2 nos, double ball bearing, MS hanging rods, etc. complete in all respect. The job includes Installation, testing and commissioning of ceiling fan, including wiring with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required upto adjacent light point complete in all resepect.Makes Havells-Velocity ES/Orient- Summer-Breeze Pro /Crompton-High Speed/Bajaj- SABSE TEZZ-EE only |
| 160 | Supply,erection,testing and commissioning of ceiling fans 1200mm sweep one star rating white color with copper winding but without regulator complete with aluminium blades, plastic canoples 2 nos, double ball bearing, MS hanging rods, etc. complete in all respect. The job includes Installation, testing and commissioning of ceiling fan, including wiring with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required upto adjacent light point complete in all resepect.Makes Havells-Velocity ES/Orient-Summer -Breeze Pro/Crompton-High Speed/Bajaj- SABSE TEZZ-EE only |
| 161 | Supply installation testing and commission of 10\\" fresh air fan 1325- 1350 RPM in plastic body. Make Orient/Usha/Bajaj/Crompton/ Havells .The job includes Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. |
| 162 | Supply and erection of exhaust fan metalic body, Size 380mm sweep 900 RPM complete in all respect with necessary connections. The job includes Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.Makes:- Havells- turbo force SP/crompton- EXHD 380-6-1/Bajaj-Supreme Plus. |
| 163 | Supply and erection of louver shutter with aluminium wings for exhaust fan of following sizes on exisiting hole complete with petty material and labour requierd to complete the job. Make :- National |
| 164 | Size 300 mm |
| 165 | Size 380 mm |
| 166 | Making hole for installation of exhausht fan/fresh air fan of size upto 450mm sweep by demolishing brick work manually/by mechanically means including disposal of malba within 50 mtr. lead and making good the wall by plastering etc as required. |
| 167 | Supply ,installation, testing and commissioning of recessed type down lighter 12 watt of 4000K/5700K/6500K (as approved by engineer in charge) having synthetic/powder coated pressure diecast alulminium body having high efficiency diffuser with more than 85% transmittance with rated life of L-70 @50,000 hours having system lumens more than 1200 lumensand efficacy better than 110 lumens/watt with CRI >80 and drivers efficiency >85% , THD less than 10% with inbuilt surge protection upto 2.5 KV. The job includes fixing down lighter and connection with 3x1.5sqmm copper wire upto 1.5mtr length from adjacent light point with all petty material and labour required to complete the job in all respect. Makes Havells-INTEGRAHE-DLR 12W LED/ Wipro-LD06-151XXX-HE/ Panasonic-PDLM35-12W/ Philips-Green perform sleek G2 DN296B-LED12S-PSE-WHS1. |
| 168 | Supply ,installation, testing and commissioning of recessed type down lighter 15 watt of 4000K/5700K/6500K (as approved by engineer in charge) having synthetic/powder coated pressure diecast alulminium body having high efficiency diffuser with more than 85% transmittance with rated life of L-70 @50,000 hours having system lumens more than 1500 lumens and efficacy better than 110 lumens/watt with CRI >80 and drivers efficiency >85% , THD less than 10% with inbuilt surge protection upto 2.5 KV. The job includes fixing down lighter and connection with 3x1.5sqmm copper wire upto 1.5mtr length from adjacent light point with all petty material and labour required to complete the job in all respect. Makes Havells-INTEGRAHE-DLR 15W LED/ Wipro-LD06-171XXX-HE/ Panasonic-PDLP35-15W/ Philips-Green perform sleek G2 DN296B-LED15S-PSE-WHS1. |
| 169 | Supply ,installation, testing and commissioning of recessed type LED panel 2'x 2',having CRCA housing duly painted with diffuser, minimum 4200 lumens (120 lumens/watt),5700K/6500K and 50000 burning hours of make Philips RC 380-B LED 42S-6500-G6/ Wipro CRCO10R036HE57G3 / Havells PLANO 2X2 PLR 36W LED865TAPS/Bajaj-BZRSQL43L-LEDGXPROWH.The job inculdes the cost of testing, commisisoning and making connection with 3*1.5 sq mm copper wire upto 1.5mt from adjacent light point, other petty material and labour etc as required to complete the same to the entire satisfaction of Engineer in Charge. |
| 170 | Supply and errection of 1x20 watt 4' long LED box / Patti type fittings with decortative end caps of make Crompton CAT no. DMLNILT8-16+LT8-20-865-2 or equivalent models of make Philips/Surya make only .The LED tube rod 20 watt polycarbonate with inbuilt driver, extruded aluminium heat sink, 50000 burning hours at 70% lumens maintenance of makes Philips/Havells/Wipro/Crompton/Bajaj. The job includes carriage, erection, making connections with 3x1.5 sq.mm copper wire from adjacent light point, testing and commissioning of the fittings etc. as requried to complete the same to the entire satisfaction of engineer in charge. |
| 171 | Supply and errection of 10 watt LED batten with inbuilt driver and polycarbonate diffuser of make Crompton CAT no. LDLSRNx10CDL or equivalent models of make Philips/Wipro/ Bajaj-Ivora/Havells make only . The job includes carriage, erection, making connections with 3x1.5 sq.mm copper wire from adjacent light point, testing and commissioning of the fittings etc. as requried to complete the same to the entire satisfaction of engineer in charge. |
| 172 | Supply and erection of fan rod made of seemless MS pipe dia duly powder coated complete in all respect. Make National |
| 173 | Size 18\\" |
| 174 | Size 24\\" |
| 175 | Size 30\\" |
| 176 | Size 36\\" |
| 177 | Size 48\\" |
| 178 | Providing and fixing of D Type fan hook duly welded on existing Girder/Angle/Channel complete in all respect. |
| 179 | Supply,erection testing and commissioning of UTP cat 6 information oulet (Red for data user end) with necessary connections of existing CAT 6- Cables complete in all respect upto the entire satisfaction of engineer in charge of the work make Molex/R&M/Semon/D-Link |
| 180 | Supply, erection, testing and commissioning UTP face plate (Single/dual) along with modular box75mmx75mm complete in all respect upto he entire satisfaction of Enigneer In-charge of the work make- Molex/R&M/Semon/D-Link |
| 181 | Supply and erection of Modular type DP switch 32 Amp 250 Volt along with modular box, modular base and cover plat 2 module complete in all respect.Make Legrand (Lyncus)/ABB (Tvisha/ Gold Medal(GIFA) Crabtree (Athena) |
| 182 | Supply and fixing of 40 amp rating, 415V, 10KA\\"C\\" curve TPMCB miniature circuit breaker suitable for inductive load of following poles in the existing DB complete with connections, testing and commissioning as required.Makes Havels/ABB/L&T/Schnieder |
| 183 | Supply and fixing of 40 amp rating, 415V, 10KA\\"C\\" curve TPNMCB miniature circuit breaker suitable for inductive load of following poles in the existing DB complete with connections, testing and commissioning as required.Makes Havels/ABB/L&T/Schnieder |
| 184 | Supply and fixing of 63 amp rating, 415V, 10KA\\"C\\" curve TPMCB miniature circuit breaker suitable for inductive load of following poles in the existing DB complete with connections, testing and commissioning as required.Makes Havels/ABB/L&T/Schnieder |
| 185 | Supply and fixing of 63 amp rating, 415V, 10KA\\"C\\" curve TPNMCB miniature circuit breaker suitable for inductive load of following poles in the existing DB complete with connections, testing and commissioning as required.Makes Havels/ABB/L&T/Schnieder |
| 186 | Supply, installation, testing and commissioning of Inverter Split AC 2TR capacity, 3 star rating with Refrigerant R-410/R-32 Gas with with ISEER in range 3.80 to 4.39 , Cooling Capacitty >= 6200 Watt. AC shall be suitable for 230 Volts+- 10% Volt ,50 Hz, Single phase , other standard manufactures Specification including installaltion charges complete in all respect upto the entire satisfaction of Engineer-in Charge. Make :- Daikin/Carrier/Hitachi/ Voltas |
| 187 | Supply, installation, testing and commissioning of Inverter Split AC 1.5TR capacity, 3 star rating with Refrigerant R-410/R-32 Gas with with ISEER in range 3.80 to 4.39 , Cooling Capacitty >= 5000 Watt . AC shall be suitable for 230 Volts+- 10% Volt ,50 Hz, Single phase , other standard manufactures Specification including installaltion charges complete in all respect upto the entire satisfaction of Engineer-in Charge. Make :- Daikin/Carrier/Hitachi/ Voltas |
| 188 | Providing & Fixing of Powder coated ready made heavy duty out door stand for Split out door as per site requirement to the entire satisfaction of Engineer- in Charge. |
| 189 | Providing and Fixing of PVC Rigid drain Pipe surface/recess in wall / floor with necessary repair to the original condition, complete in all respects from indoor unit to Disposal Points as directed by the E.I.C. Size ¾” including specials- Make- Diplast or Equalivent. |
| 190 | Providing and Fixing of 22 gauge soft copper piping of size 3/8” & 5/8” or as per original manufacturer of A/C size, for Liquid & Suction sides, between indoor & outdoor units with 6 mm thick nitrile rubber insulation & protective covering for exposed weather including cost of chasing brick wall/RCC wall & repairing to original condition.Make Rajco., Mandev, Totaline. |
| 191 | Providing & fixing of 4 core 2.5 sqmm flexible coppe wire ISI Marked complete. Makes Havell/Polycab as per site. |
| 192 | Supplying and fixing of suitable size GI box with modular plate and cover 12 modules in front on surface or in recess, including providing and fixing 4 nos 5/6 A modular switch, 3 nos 5/6 A modular socket outlet and one 10 AMP international socket, with necessary connections etc. as required. (for computer plugs to be used in non residential buildings.) |
| 193 | Supplying and fixing of Surface/recess mounting 12 way TP &N vertical load line distribution board double door steel, dust protected, duly powder coating inclusive of tinned copper bus bars,160Amp (W/o MCCB) and outgoing MCB's (Without MCB's) complete in with all petty material and labour required.Makes Havels/ABB/Schnieder |
| 194 | Supply and laying of XLPE insulated PVC sheathed Aluminum conductor Armored cable of 1.1 KV grade as per IS 7098 (Part-I) 1988 (amended upto date) of the following size to be laid in the existing HDPE/DWC pipe as required. The job included labour charges of laying the cable in existing pipe or to be fixed with M S Sadels and making connections etc. Make of cable:- Polycab/Havells/KEI/RR Kables |
| 195 | XLPE armored aluminium conductor cable 35 sqmm X 3.5 core |
| 196 | XLPE armored aluminium conductor cable 70 sqmm X 3.5 core |
| 197 | XLPE armored aluminium conductor cable 150 sqmm X 3.5 core |
| 198 | Supply and fixing of 40 amp rating, 415V, 10KA\\"C\\" curve Single pole & Neutral miniature circuit breaker suitable for inductive load in the existing DB complete with connections, testing and commissioning as required.Makes Havels/ABB/Schnieder |
| 199 | Supply and installation of sheet steel enclosure for TP/FPMCCB up to 100amp with neutral link on existing board/recessed in wall with all petty material and labour required to complete the job in all respect. Make Havells/ABB/L&T/Schnieder |
| 200 | Supply and installation of sheet steel enclosure for TP/FPMCCB up to 250 amp with neutral link on existing board/recessed in wall with all petty material and labour required to complete the job in all respect. Make Havells/ABB/L&T/Schnieder |
| 201 | Supply Installation, testing and commissioning of double door type LT panel board of suitable size, duct and vermin proof, fabricated out of 1.6mm thick CRCA sheet, steel powder coated with 7 tank process for better environmental protection ,MCCB panel board should be manufactured and supplied by ISO-1 certified OEM of MCCB. The bus bar system should be duly type tested at NABL accrediated lab for short time to withstand current of 1 second. The panel board should be suitable for floor or wall mounting and should be robust construction. The panel board should have cable alleys on both sides for easy cable termination and should be complete with digital Ammeter, Voltmeter, Selector switches fuses indication lamps etc Make Havell's Cat no IHVG02500400 or equivalent in ABB/Schneider/L&T. The panel should comprises of the following items.a. Copper bus bar of rating equal or higher than the incomer current rating.b. Provision for incomer MCCB 250 amp, 4 pole 36KA breaking capacity =onec .Provision for outgoing TP MCCB's upto 125 amp=4 nosd .Cable alley on both sides Make Havells cat no-ISSBOUO692 or its equivalent in ABB/Schneider/L&T- 01 sete. Digital meter module with Ammeter, Votlmeter, Selector switch, CSS's control fuse and indication lights Havell's Make Cat no. ISSB0U0707= 1 setThe panel includes with all petty material and labour required to recess the panel in wall complete in all respect |
| 202 | Chasing floor for laying pipes of any size/type complete in all respect Please Enable Macros to View BoQ information |
