|
| 1 | Dismantling old plaster and pointing in cement or lime and raking out joints to 15mm depth, watering and disposal of unserviceable materials with all leads all complete as per direction of E/I. |
| 2 | Taking down old door and window shutters including stacking serviceable materials within 15M,. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I. |
| 3 | Dismantling R.C.C. work including stacking serviceable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I. |
| 4 | Taking down chaukhats in doors including stacking serviceable materials within 15M,. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I. |
| 5 | Extra for cleaning the old surface by scraping the entire old white wash or colour wash including cost of scaffolding all complete as per direction of E/I |
| 6 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 7 | Providing 1.5mm cement punning including curing, carriage of water with all leads and lift as per building specification and direction of E/I. |
| 8 | Providing 250mm. Wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 250mm apron including cost of eartwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I. |
| 9 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 10 | Centering and shuttering including strutting, propping etc. and removal of form for CHAJJA |
| 11 | Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. |
| 12 | Providing 6mm cement plaster (1:4) in celling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. |
| 13 | Supplying iron and steel material as par specification and direction of E/I. |
| 14 | Supplying welder grade -1 as par specification and direction of E/I. |
| 15 | Supplying healper as par specification and direction of E/I. |
| 16 | Supplying, fitting, and fixing M.S. Grill made of 20X6mm M.S. Flate as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction of E/I. (where materials is not supplied by the deptt |
| 17 | Supplying, fitting and fixing fully glazed steel door, window or ventilations of standard rolled 'Z' and mullion steel sections and size as per IS-1038 joints met and welded with 100X16X3mm M.S. lugs fixed in cement concrete (1:2:4) block 15X10X10cm, size including cost of oxidised iron fittings, with hinges, handle per steps, catch springs, 3mm thick plain glass panes with Aluminimum beads and inner frame fixed with lugs with 20mm long 6.3mm G.I. counter sunk machine screw and nuts and applying a coat of red lead paint carriage to work site hoisting and placing in position in all storys and taxes all complete as per building specification and direction of E/I. |
| 18 | Providing and laying 25mm thick kotah stone slab flooring of approved size texure and colour over 19mm thick base of lime mortar (1:1:1) (limeputty:surkhi:coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 19 | Providing and laying 25mm thick kotah stone tiles in risers of steps skirting and pillars of approved size texure and colour laid over 12mm thick cement mortar (1;30 and joined with grey cement slurry mixed with pigment to match the shade of the slab including rub bing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I |
| 20 | Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm . |
| 21 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc.,., complete. |
| 22 | Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointing with white cement including rubbing, polishing and cost of curring taxes and royalty all complete as per building specification and direction and E/I. |
| 23 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.(Flat 30x6 mm for diagonal braces and central cross piece) |
| 24 | Supplying, fitting and fixing collapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2mm at 100mm centers and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of T.iron 40 x 40 x 6mm with 38mm dia steel pulleys complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of red lead paint, car riage, hoisting and taxes all complete as per building specification and direction of E/I. |
| 25 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :( 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size) |
| 26 | Providing 12mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. |
| 27 | Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3 mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the samemembrane manufactured of density at 25°C, 0.87 - 0.89 kg/litre and viscocity 70 - 160 cps. Over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 350/300 N/5 cm. |
| 28 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 29 | Providing two coats of oil bound distemper of approved shade and make over old surface including washing cleaning and papering the walls, scaffolding, washing of floors and taxes all complete as per building specification and direction of E/I. |
| 30 | Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm). |
| 31 | Providing two coat of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I. |
| 32 | providing Tor steel reinforcement of 8mm dia rods as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (only valid for SAIL & TATA STEEL) |
| 33 | Dismantling patent stone floor including stacking serviceable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I. |
| 34 | Supplying Un-skilled labour for cleaning the site all complete jobs as per specification and direction of E/I(Cleaning the site and roof surface) |
| 35 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1;2;4 |
| 36 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 37 | SEPTIC TANKEarth work in excavation in foundation trenches in ordinary soil ( vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I. |
| 38 | Extra for earthwork in hard soil as per specification and direction of E/I. ( vide classification of soil item-B) |
| 39 | Providing coarse clean sand in filling in in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume) |
| 40 | Providing designation 75A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I. |
| 41 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 |
| 42 | Providing designation 75B brick work in C.M (1:6 ) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I. |
| 43 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size) |
| 44 | Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. |
| 45 | Providing 1.5mm cement punning including curing, carriage of water with all leads and lift as per building specification and direction of E/I. |
| 46 | Centering and shuttering including strutting, propping etc. and removal of form for |
| 47 | Centering and shuttering including strutting, propping etc. and removal of form for |
| 48 | Centering and shuttering including strutting, propping etc. and removal of form for |
| 49 | providing Tor steel reinforcement of 8mm dia rods as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (only valid for SAIL & TATA STEEL) |
| 50 | providing Tor steel reinforcement of 8mm dia rods as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (only valid for SAIL & TATA STEEL) |
| 51 | BOUNDRAY WALLDismantling old plaster and pointing in cement or lime and raking out joints to 15mm depth, watering and disposal of unserviceable materials with all leads all complete as per direction of E/I. |
| 52 | Extra for cleaning the old surface by scraping the entire old white wash or colour wash including cost of scaffolding all complete as per direction of E/I |
| 53 | Providing designation 75 B brick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including, providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 54 | Dismantling pucca brick or lime work including stacking serviceable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I. |
| 55 | Earth work in excavation in foundation trenches in ordinary soil ( vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I. |
| 56 | Providing coarse clean sand in filling in in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume) |
| 57 | Providing designation 75A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I. |
| 58 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 59 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level. |
| 60 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size) |
| 61 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 62 | Centering and shuttering including strutting, propping etc. and removal of form for foundation |
| 63 | Centering and shuttering including strutting, propping etc. and removal of form for column |
| 64 | Centering and shuttering including strutting, propping etc. and removal of form for beam |
| 65 | Centering and shuttering including strutting, propping etc. and removal of form for |
| 66 | providing Tor steel reinforcement of 8mm dia rods as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (only valid for SAIL & TATA STEEL) |
| 67 | Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. |
| 68 | Supplying, fitting and fixing M.S. grill gate with M.S. grill made of 20X6mm M.S. flats or 16mm M.S. square bars fitted on 25X25X6mm M.S. Angle frame of size 60X60X6mm. Including cost of fabrication, providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/I. |
| 69 | Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and cleaning the surface throughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I. (Mode of measurement area shall be multiplied by the co-efficient as indicated in building specification) |
| 70 | Providing two coat of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I. |
| 71 | Providing two coats of snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper scaffolding , curing and taxes all complete as per building specification and direction of E/I. |
| 72 | Earth work in excavation in foundation trenches in ordinary soil ( vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I. |
| 73 | Providing coarse clean sand in filling in in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume) |
| 74 | Providing designation 75A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I. |
| 75 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 |
| 76 | Supplying Un-skilled labour for cleaning the site all complete jobs as per specification and direction of E/I(Cleaning the site and roof surface) |
| 77 | (A) SAND LEAD-6 KM(1K+5P) |
| 78 | (B) STONE CHIP LEAD-22 KM |
| 79 | (C) STONE METAL-52 KM |
| 80 | (D) BRICK LEAD-8 KM(1K+7P) |
| 81 | ( E ) LOCAL SAND -3 KM |
| 82 | WATER SUPPLY AND SANITARY WORKSupplying, fitting and fixing 550x400x400 mm size viterous white glazed earthen ware wash hand basin of Parry or Hindustan or any other I.S.S. approved make supported on pointed c.l. or R.S. brackets 32 m C.I. brass waste 15 mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350grms., 32 mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/l. |
| 83 | Supplying, fitting and fixing vitreous white glazed earthen ware I.W.C. Of parry Hindustan or any other I.S.S. Approved make with 100mm H.C.I. 'P' trap 15liters C.I. Pull and let go flushing cistern of names or other I.S.S. Equipment make, complete with all fittings, C.I. or C.C. brackets 32mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pert of vitreous white glazed earthenwere were footrest to be fixed in floor 15mm C.I. body brass spindle stope cock of weight not less than 50grms, 15mm P.V.C. connection pipe 450mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I.(A) 510 mm long(c) with 10.00 lit. Low level PVC Cistern |
| 84 | Supplying, fitting and fixing flat back or angular, lipped front viterous white glazed earthen ware urinal of Hindustan 'Parry' or any other approved I.S.S. make with 5 litres capacity C.i. automatic flusing cistern of reliance for any other I.S.S. approved make with all fittings with C.I. or R.S. brackets, standard size G.I. flush pipe with fitting clamps, 15mm C.I. body brass spindle stop cock of approved quality weight not less than 400 grams, 15mm PVC/Alkthene pipe 450mm longwith brass coupling at both ends and doing plumber joints including priming coat of red oxide, cutting wall and floor making good the same etc. all complete as per specification and direction of E/I.(FLAT BACK OR STANDING CORNER 600X350MM) |
| 85 | Providing and fixing male ended 15 mm dia brass bib cock of approved qulity (wt not less than 350 gms)with extra socket . |
| 86 | Providing and fixing C.I STOP COCK 15 mm dia brass bib cock of approved qulity (wt not less than 350 gms)with extra socket . |
| 87 | SUPPLYING FITTING AND FIXING OF C.I BRASS PILLAR COCK |
| 88 | Providing and fixing G.M non return valve horizontal/vertical type of approved quality as per specification (Horizontal 25 mm dia ,wt not less than 375 gms)Horizontal non-return valve-25 mm dia wt not less than 375 gms |
| 89 | Vertical non-return valve 25 mm dia wt not less than 375 gms |
| 90 | Providing and fixing 15mm size CP brass pillar cock (wt not less than 350 gms CI body brass spindle pillar cock of approved quality (C.I body brass spindle) |
| 91 | Providing and fixing Gun metal full way valve of approved qualtiy, all complete as per specification and direction of E/l.(25 mm dia and weight not less than 500 gms) |
| 92 | Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/l.Mirror of 6 mm thick plate glass beveled edge mirror includind cp brass revolving fitting 3mm plywood board'(600X450 mm) |
| 93 | CP brass dish container |
| 94 | CP brass towel rail 20mmx600mm with bracket container |
| 95 | Construction of inspection chamber as direction of E/I. |
| 96 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge : External work 15 mm dia |
| 97 | 20 mm dia |
| 98 | 25 mm dia |
| 99 | Making hole in wall for G.I. pipe and restoring the same all cost complete(250 mm dia)(125 mm thick wall, 125 mm dia) |
| 100 | Polythene water storage tank of mark with cover and-suitable locking system in double layer confirming to lS: 12701-1996 with Latest revision. |
| 101 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.(110mm ) |
| 102 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.12.42.1.2 Coupler 110 mm dia |
| 103 | 12.42.2.2 Single pushift coupler110 mm dia |
| 104 | 12.42.4.2 Single tee without door 100 mm dia |
| 105 | 12.42.5.2 Bend 87.5o 110 mm dia |
| 106 | 12.42.6.2 Shoe plain 110 mm dia |
| 107 | MAKING SOAK PIT 2.5 M DIA 3.0 M DEEP etc.. |
| 108 | Providing and fixing Gun metal full way valve of approved qualtiy, all complete as per specification and direction of E/l25 mm dia and weight not less than 500 gms) |
| 109 | 32 mm dia and weight not less than 700 gms) |
| 110 | Making hole in wall for G.I. pipe and restoring the same all cost complete(250 mm dia |
| 111 | Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/l.Mirror of 6 mm thick plate glass beveled edge mirror includind cp brass revolving fitting 3mm plywood board'(600X450 mm) |
| 112 | Supplying, fitting and fixing vitreous white glazed earthen ware I.W.C. Of parry Hindustan or any other I.S.S. Approved make with 100mm H.C.I. 'P' trap 15liters C.I. Pull and let go flushing cistern of names or other I.S.S. Equipment make, complete with all fittings, C.I. or C.C. brackets 32mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pert of vitreous white glazed earthenwere were footrest to be fixed in floor 15mm C.I. body brass spindle stope cock of weight not less than 50grms, 15mm P.V.C. connection pipe 450mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I.(A) 510 mm long(c) with 10.00 lit. Low level PVC Cistern |
| 113 | Supplying, fitting and fixing vitreous white glazed earthen ware E.W.C. Of parry Hindustan or any other I.S.S. Approved make with 100mm H.C.I. 'P' trap 15liters C.I. Pull and let go flushing cistern of names or other I.S.S. Equipment make, complete with all fittings, C.I. or C.C. brackets 32mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pert of vitreous white glazed earthenwere were footrest to be fixed in floor 15mm C.I. body brass spindle stope cock of weight not less than 50grms, 15mm P.V.C. connection pipe 450mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I.(A) 510 mm long(c) with 12.50 lit. Low level PVC Cistern |
| 114 | Earth work in excavation for laying different type and size of RCC spun |
| 115 | labour for applying fitting and fixing NP2 RCC spun pipe |
| 116 | supplying and labours for construction of inspection chamber |
| 117 | supplying and fixing NP2 PIPE |
| 118 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A,including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Singlesocketed pipes.75 MM |
| 119 | 110MM |
| 120 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised RigidPVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS :5382, leaving 10 mm gap for thermal expansion.75 MM |
| 121 | 110 MM |
| 122 | SINGLE PUSH FIT COUPLER75 MM |
| 123 | 110 MM |
| 124 | SINGLE TEE WITH DOOR75 MM |
| 125 | 110 MM |
| 126 | SINGLE TEE WITHOUT DOOR75 MM |
| 127 | 110 MM |
| 128 | BEND75 MM |
| 129 | 110 MM |
| 130 | SHOE75 MM |
| 131 | 110 MM |
| 132 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass wasteof standard pattern, including painting of fittings and brackets, cutting and making good the wallswherever require:White Vitreous China Wash basin size 550X400 mm with a pair of 15 mm C.P. brass pillar taps |
| 133 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for thereception of pipes and fittings |
| 134 | Supplying, fitting and fixing vitreous white glazed earthen ware Urinal Hindustan or any other I.S.S. Approved make with Pull and let go flushing cistern of names or other I.S.S. Equipment make, complete with all fittings, C.I. or C.C. brackets 32mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pert of vitreous white glazed earthenwere were footrest to be fixed in floor 15mm C.I. body brass spindle stope cock of weight not less than 50grms, 15mm P.V.C. connection pipe 450mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I.600X350 |
| 135 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked,with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflowpipes but without fittings and the base support for tank. |
| 136 | Rectangular type with openable circular lid150 mm nominal size square 100 mm diameter of the inner hinged round grating |
| 137 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & coldwater supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testingof joints complete as per direction of Engineer in Charge.25 MM |
| 138 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & coldwater supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 mspacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost ofcutting chases and making good the same including testing of joints complete as per direction ofEngineer in Charge15MM |
| 139 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & coldwater supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittingswith one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction ofEngineer in Charge15MM |
| 140 | SPECIAL FITTING IN CP BATHROOM pillar cock |
| 141 | bib cock |
| 142 | towel rail |
| 143 | soap dish |
| 144 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricksand S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. |
| 145 | ELECTRICAL WORK WGPVT-wiring for light /point/fan point/exhaust fan/call bell point 1.5 sqmm FRPVC insulated copper conductor….do…all jobs as per direction of E/I (Group-B) |
| 146 | Power plug wiring in PVC conduit (2 x 4 sq. mm) :-Wiring for light/ power plug with 2 x 4 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit along with 1 Nos. 4 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required. |
| 147 | Circuit/submain wiring in PVC conduit:- Wiring for circuit/submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit etc. as required.(2X1.5sqmm+1x1.5sqmm.earth wire) |
| 148 | .(2X2.5sqmm+1x2.5sqmm.earth wire) |
| 149 | (2X4 sqmm+1x4sqmm.earth wire) |
| 150 | (2X10sqmm+1x6sqmm.earth wire) |
| 151 | S/F Modular type switch socket - Supplying and fixing following modular type switch/socket on the existing modular plate and switch box including connection but excluding modular plate etc. as required |
| 152 | S/F modular type switch socket supplying and fixing of the following modular switch socket box etc. 5/6 amps 3 pin socket outlet |
| 153 | S/F Modular type electronic fan regulator :-Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc, as required. |
| 154 | Supplying and fixing following size/ modules G.I. box along with modular base & cover plate for modular switches in recess etc as required.1 or 2 module (78mm x 78mm x 45mm) |
| 155 | 4/5 module (78mm x 140mm x 50mm) |
| 156 | 6 module (78mm x 205mm x 50mm) |
| 157 | 8/9 module (78mm x 230mm x 60mm) |
| 158 | 12 module (135mm x 205mm x 60mm) |
| 159 | S/F power plug point with modular type accessories :-supplying and fixing suitable size G.I box with modular plate cover in front on with modular surface or in recess including providing and fixing 6 pin 15/16 amps modular socket outlet and 15/16 amps modular switch etc |
| 160 | S/F Batten holder:- Supplying and fixing Batten/Angle holder including connection etc as required. |
| 161 | Supplying and fixing 3 pin 5 amps.ceiling rose on the existing junction box/wooden block including connection etc. |
| 162 | Installation of exhaust fan upto 450 mm. sweep in the existing opening, including making the hole to suit the size of the above fan, making good the damage, connection, testing, commissioning etc as required. |
| 163 | Supplying and fixing following way, three pole and neutral, sheet, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way (4 + 12), Double door, Horizontal type |
| 164 | 6 way (4 + 18), Double door, Horizontal type |
| 165 | Supplying and fixing 6 amps to 32 amps rating, 240 volts, 'B' series, miniature circuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 6/32 amps, single Pole, \\"B\\" serie |
| 166 | Supplying and fixing following rating, double pole,240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amp |
| 167 | Supplying and fixing following rating, four pole,415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40amps |
| 168 | Providing and fixing following capacity double pole/ TP&N sheet metal switch disconnector fuse unit in existing metal board with rewireable type fuses, including drilling holes in metal board, making connections, etc as required. 16 amps, double pole |
| 169 | 10/12W LED Tube Light |
| 170 | 20/22W LED Tube Light |
| 171 | 1200 mm (48') ac celling fan |
| 172 | S/F/F 9/10Watt LED Bulb |
| 173 | metal exhaust fan 12\\" |
| 174 | laying of one number PVC insulated and PVC sheathed/ XLPE power cable of grade exceeding 1.1 KV but not exceeding 11 KV of size not exceeding 120 sq. mm direct in ground including excavation, sand chshioning, protective covering and refilling the trench etc as required. |
| 175 | Earthing with G.I. earth pipe 4.5 mtr long, 40mm dia including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal and salt as required. |
| 176 | Earthing with copper earth plate 600mm x 600mm x 3mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc as required. (but without charcoal or coke and salt) |
| 177 | Supplying and laying 8 SWG copper wire at 0.50 metre below ground level for conductor earth electrode, including soldering etc. as required. |
| 178 | Providing and fixing 25mm x 5mm copper strip in 40 mm dia G.I. pipe from earth electrode, as required. |
| 179 | Providing and fixing of lightning conductor final, made of 25mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 3 mm thick G.I. base plate including holes etc. complete as required. |
| 180 | Reverting, sweating and soldering of copper/G.I. tape (with another copper/ G.I. tape, base of the finial or any other metallic object) as required. |
| 181 | Providing and fixing G.I. tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor complete as required. (for horizontal run) |
| 182 | Providing and fixing G.I. tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor complete as required. (for vertical run) |
| 183 | SITC LED FLOOD LIGHT 30W |
| 184 | 25/100 amps, 10 KA fixed thermal setting |
| 185 | 250 amps, 35 KA, fixed thermal setting |
| 186 | 25/100 amps, 16 KA, fixed thermal setting |
| 187 | 6/32 amps, DP |
| 188 | 50/63 amps, DP |
| 189 | Providing and fixing following capacity busbar chamber with 4 strips of suitable size made of copper, heavy duty, complete with all accessories including connections, earthing the body, etc as required.300AMP |
| 190 | Providing and fixing following capacity 2 pole/ 4 pole ON/ OFF-Load changeover switches with side handle opreation, in sheet enclosure in existing metal board including drilling holes in metal board, making connection, earthing the body etc. as required. 100AMPS 4 POLE CHANGEOVER |
| 191 | PILOT LAMP INDICATER |
| 192 | 3 WAY 4 POLE SELECTOR SWITCH |
| 193 | DIGITAL VOLT METER |
| 194 | DIGITAL A METER 500V |
| 195 | CT COIL |
| 196 | Panel supplying fitting fixing and testing commissioing panel board |
| 197 | DEEP BORINGHYDT: Cost of Drilling 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.From 0.00 M to 50.00 M Below G.L |
| 198 | From 51.00 M to 100.00 M Below G.L |
| 199 | From 101.00 M to 125.00 M Below G.L |
| 200 | Supplying and fixing assembling lowering vertical postion in bore well,unplactisized PVC medium casing(CM) pipe of required dia conforming to IS 12818,including labour charge ,fitting & accessories etc (200 mm dia nominal size) |
| 201 | Development of tube well in accordance with IS : 2800 (part I) and IS:11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. |
| 202 | Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of borewell housing/ casing pipe, removable as per requirement, all complete for borewell of: |
| 203 | Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell asper IS: 2800 (part I), including necessary bolts & nuts of required size complete. |
| 204 | Supplying 100 mm dia submersible pump set confirmining to IS 8034 and motor confirming to IS 9283 Pump shall be suitable for various …..do…do...all jobs as per direction of E/I |
| 205 | Supplying and fixing 3 kva stabilizer of L & T or any approved ISI mark to control the voltage all complete as per specification and direction of E/I |
| 206 | S/F/F Starter Pannel board including voltmeter, ameter, On/Off switch and provision for dry run protection as per IS Specification for 2 H.P. submersible motor pump encased in painted mild steel sheet box with glass front and looking arrangement complete assembly mounted on wall all complete job as per direction of E/I. |
| 207 | 3 Core PVC insulated PVC sheated copper conductor flat submersible cable .supplying flate flexible subermissible cable with cooper conductor etc(3 core 4 sq mm copper wire) |
| 208 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & coldwater supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittingswith one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction ofEngineer in Charge. |
| 209 | Add 18% for G.S.T. |
| 210 | Labour Cess Please Enable Macros to View BoQ information |
