|
| 1 | Providing and fixing 35mm thick phenol bounded factory manufactured solid flush door shutter ISI marked with both side 4mm teak ply in the existing chowkhat. The rate includes the cost of all necessary stainless steel fittings and french spirit polish on teak ply complete in all respect to the entire satisfaction of Engineer-in-charge. |
| 2 | Providing and Fixing 35mm thick 2nd class teak wood (kiln seasoned) wire gauge door shutter consisting of 100mm x 35 mm style and top rail 150 mm x 35 mm lock rail 200mm x 35 mm bottom rail wire mesh 22 x 12 mm gauge fixed with 1/2” x 3/4” teak wood (kiln seasoned) beading, incluuding Stainless Steel fittings and french spirit polish, complete fixed in position and in all respect to the entire satisfaction of Engineer-in-Charge. |
| 3 | Providing and fixing 2'-0” deep cupboard /cabinet consisting of 19mm thick commercial board and 6mm thick ply on back side, 4mm thick teak ply pasted on the exposed surface and making shelves in cabinet 0.8mm mica inside canbinet . The rate further includes the cost of lipping, piano hinges, cupboard lock, screws, nails, 2 nos. fancy s.s. handles, 2 nos. magnetic catchers, fevicol and painting two coats over one priming coat and preparation of surface on board and ply surface and spirit polishing on teak ply complete in position as per entire satisfaction of Engineer-in-charge. |
| 4 | Providing and fixing 2nd class teak wood (kiln seasoned) chowkhat 4 1/2\\" x 2 1/4\\"including cost of corner straps, iron hold fasts, hinges, screws,nails, fevicol etc. and spirit polish of chowkhats. Rate includes the cost of dismantling of all damaged chowkhats and making good the damage to walls plaster and floors as required including, disposal of rubbish to the dumping ground the rate further includes the cost of two coats Spirit polish complete in all respect and to the entire satisfaction of Engineer-in-Charge |
| 5 | Providing and fixing book rack made out of with side, top and bottom frame 1'-0\\" deep and inner shelve 9\\" deep made out with 19mm thick commercial board, 6mm thick ply on the back side, teak ply on the exposed board surface including front side of 6mm ply, teak wood lipping on board edges, french polish on the teal ply and lipping and synthetic enamel paint on the back side of 6mm ply complete in position as per entire satisfaction of Engineer-in-charge. |
| 6 | Providing and fixing 8mm thick wooden laminated floor class of use 31/23 having wear resistance level of AC-4 as per EN-13329 with a direct pressure laminate surface including profile, treated with aluminium side, flooring of approved colour and shade complete in all respects and to the entire satisfaction of the Engineer in charge. |
| 7 | Providing and fixing heavy duty telescopic channel for drawers 18\\" to be fixed with necessary screws complete in all respects and to the entire satisfaction of the Engineer in charge. |
| 8 | Providing and fixing heavy duty S.S. kitchen hydraulic auto hinges accessories i.e. hydraulic auto hinges fixing in the existing cabinet complete in all respects and to the entire satisfaction of the Engineer in charge |
| 9 | Providing and fixing 3.0 mm thick clear polycarbonate sheet to be fixed on the existing MS / wooden frame with self drilling machine screws including remove the old polycarbonate sheet complete in all respect to the entire satisfaction of Engineer-in-charge. |
| 10 | Providing and fixing 1.5mm thick polycarbonate sheet to be fixed on the existing MS frame with self drilling machine screws complete in all respect to the entire satisfaction of Engineer-in-charge. |
| 11 | Providing and fixing 60 mm thick high density rubber moulded precast cement concrete paver block grey/ colored/ polished/ designer (manufactured by vibro hydraulic pressure process) consisting of design mix of cement, sand and fine aggregate having designation M35 ISI marked including the cost of good quality color and hardening agents. The paver should be compiled with tensile strength and breaking load as per BIS 6717-1993 and shall be tested against resistance to bear as per IS 1237-1980 (specification for cement concrete floor tiles). The paver should be laid over layer of 25 mm average thick screened coarse sand to the required slope and filling the joints with fine sand complete in all respects and to the entire satisfaction of Engineer in charge. |
| 12 | Providing and fixing main entry gate 5'-11\\" high (paint finish) consisting of shesham wood battens of size 5'-11\\" x 6\\" x 3/4\\" vertically, including making grooves for interlocking, with the help of M.S. nuts and bolts including paintng two coats of synthetic enamel paint over one coat of wooden primer, on the existing M.S. frame completely fixed in position in all respect to the entire satisfaction of Engineer-in-charge. |
| 13 | Steel work in built up frame made of / M.S. flat / M.S. pipe / M.S. angles of various sections including cutting, hoisting fixing in position and applying a priming coat of approved steel primer and two coats of snthetic enmael paint, welded and bolted including special shaped washers etc.. The work is required for making security wall jaffery/ ladder/grills/ frame work for shed or sunshade / other mis work.The steel work is to be provided at the site of the building complete in all respect and to the entire satisfaction of Engineer-in-charge. Please Enable Macros to View BoQ information |
