|
| 1 | Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out soft/loose soil complete all as specified and directed. |
| 2 | M&L for excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits,manholes, pier holes, etc. n.exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft/loose soil complete all as specified and as directed. |
| 3 | M&L for PCC 1:4:8, type D-2 (40mm graded agg) as in foundations,filling and mass concrete complete all as specified and as directed. |
| 4 | M&L for Pre-cast cement concrete block masonry with solid blocks 1:3:6, type C-1, exc 10cm in width and setting in mortar in CM 1:6 complete all as speified and directed |
| 5 | M&L for 40mm thick DPC (Damp proof course) to horizontal or vertical surfaces in cement concrete 1:2:4 type B-0 (using 12.5mm graded agg) incl necessary form work over laying of polythene film 50 micron thick laid on a coat of bitumen primer @ 0.30 to 0.50kg/sqm complete all as specified and directed. |
| 6 | M&L for RCC (nominal mix) in type B1, 1:2:4 (using 20mm graded agg) as in Beams, cantilevers, bressummers,lintels over 1.5m spancomplete all as directed |
| 7 | S&F for Mild steel TMT bars 6-8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clip complete all as directed |
| 8 | -Ditto- all as per item No 7 here in before but 6mm to 8mm bars for stirrups |
| 9 | Use & formwork to sides and soffits of floor or roof beams,columns, lintels, cantilevers, shelves and similar work etc complete all as specified and directed |
| 10 | M&L for 15mm thick cement plaster in CM 1:4 on bricks on concrete surfaces finishing the surfaces even and smooth without using extra cement with two coats of cement base paint on new surface all as specified. |
| 11 | M&L for 15mm thick cement plaster in CM 1:6 on bricks on concrete surfaces finishing the surfaces even and smooth without using extra cement with two coats of OBD over a coat of primer on new surface all as specified. |
| 12 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm of soft/loose soil complete all as specified and directed |
| 13 | Removing excavated material n.exc 50m and depositing where directed at a level n exc. 1.5 m above the starting point of soil complete all as specified and directed |
| 14 | S&F for rolled mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) incl distance pieces, cleats etc. conforming Fe 410-W(Gde-E-250) quality-B complete all as specified and as directed. |
| 15 | S&F for plates (plain or chequred) channels, square cut to notched(ordinery and counter sunk) forming holes, without any attachment Fe 410-W(Gde-E-250) quality-A complete all as specified and as directed. |
| 16 | S&F for 0.50mm thick pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws with two corrugation side lap complete all as specified and as directed. |
| 17 | -Ditto- all as per item No 16 here in before but 0.50mm thick plain sheets on ridges |
| 18 | M&L for preparation of new steel or iron surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of zinc chrome red oxide primer all as specified and as directed. |
| 19 | S&F 15mm bore tubes medium grade galvanized ISI marked with all fittings short pieces and fixed complete to walls, floor, ceiling etc as specified. |
| 20 | S&F 20 mm bore GI tubing 'medium grade' galvanised, with all fittings and fixed complete to walls and ceiling or laid in floors all as specified and as directed. |
| 21 | M&L for cutting chases, pinning in making good to faces where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, lintels etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good cutting n.exc 10cm girth on brick wall complete all as directed. |
| 22 | S&F in vitreous China wash down water closet pan (pedestel pattern) ETWC white, including trap connection to drain (outgoing pipe) and to flushing pipe, antisyphonage pipe, PVC jet for Pedestal pattern pan including 450/600mm long PVC connection and plastic water closet seat of white in colour, back closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device etc complete all as specified. Make : Cera/Prayag/Johnson Pedder. |
| 23 | S&F in vitreous China squatting pan Orissa pattern size 580 x 440mm white with integral foot rest (excluding flushing cistern and flush pipe), including P-trap (PVC) 100 mm dia., connection to flushing pipe, anti-syphonage pipe complete incl making good to floor all as specified. |
| 24 | S&F in vitreous china wash hand basin white of bowl size 550 x 450mm incl waste coupling and PVC waste pipe, 32mm dia, pillar tap cast copper alloy with capstan heads chromium plated fancy 5mm bore to be fixed with and incl MS brackets complete all as specified. Make : Cera/Prayag/Johnson Pedder. |
| 25 | S&F in 10 ltr capacity PVC valveless syphonic action type flushing cistern low level white with inlet ball valve float ovel handle including brackets and PVC flushing pipe of polyethylene of low or high density or PVC 32mm dia complete all as specified. Make : Cera/Prayag/Johnson Pedder. |
| 26 | S&F in repair vitreous china Urinal, Half stall type, white including waste pipe and CP brass spreader for fixing with 15 mm dia pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plug with and incl 60mm long brass screws, pointing around urinal back in cement; flush pipe, grating and union for discharge pipe complete all as specified. |
| 27 | S&F PVC (SWR) soil, waste and vent pipes, 110 mm dia, in any length , single socketed,jointed with rubber ring joints/adhesive, fixed to wall, with PVC clamps, ISI marked complete all as specified and directed |
| 28 | S&F PVC (SWR) soil, waste and vent pipes, 75 mm dia, in any length , single socketed,jointed with rubber ring joints/adhesive, laid in trenches or in floors, ISI marked complete all as specified and directed |
| 29 | S&F PVC (SWR) bends, 110mm bore, any radius complete all as specified and directed |
| 30 | S&F PVC (SWR) bends, 75 mm bore, any radius complete all as specified and directed |
| 31 | S&F PVC (SWR) junction single (Single T) equal or 110 mm bore, |
| 32 | S&F PVC (SWR) junction single (Single T) equal or 75 mm bore, |
| 33 | S&F PVC vent cowl of 75mm dia complete all as specified and directed |
| 34 | S&F PVC vent cowl of 110mm dia complete all as specified and directed |
| 35 | S&F 110mm bore PVC (SWR) 'P’ trap fixed on floor with necessary PCC complete all as directed |
| 36 | S&F in 75mm bore PVC (SWR) floor trap plain with CP grating including jointing with solvent cement to waste pipe fixed in cement concrete type B-1, 1:2:4 using 20mm graded stone aggregate complete all as specified. |
| 37 | S&F in two way bib taps with wall flange quarter turn suitable for 15mm bore pipe long body fancy type brass CP, screwed down screwed for iron pipe or brass ferrule complete all as specified. Make Johnson VIVA new series Cat part No: T4808C or of equivalent |
| 38 | M&L for 15 mm bore fancy type stop cock chromium plated cast copper alloy with wall flange complete all as specified and directed |
| 39 | S&F in hand shower (health faucet) of ABS body with 1.0m long easy flexible tube in chrome finish and wall hook complete all as specified and directed by Engr-in-charge. Make : Jaquar Cat No ALE-ESS-585 or of equivalent |
| 40 | M&L PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified and as directed. |
| 41 | S&F in 600x450mm bevelled edge mirror of selected quality glass moulded on 6mm thick AC board or commercial plywood & fixed to wooden plugs with chromium plated brass screw complete all as specified and as directed. |
| 42 | M&L for broken stone hard core of gauge n.exc 63mm deposited, spread and leveled in layers not exc 15cm thick, watered and rolled, rammed to a true surface all as directed. |
| 43 | M&L for 75mm thick PCC type B- 2, 1:2:4 (40mm graded aggregate) as in sub base complete all as specified and directed |
| 44 | M&L for Non skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.06 sqm but n.exc 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 20mm thick screed bed or bedding of layer in CM 1:6 complete all as specified an directed |
| 45 | M&L glazed ceramic coloured tiles of size 450 x 300 x 7mm thick, on vertical surfaces of walls such as skirting dado etc. set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick rendering in cement mortar 1:4 complete all as specified and as directed. |
| 46 | M&L for machine cut 18-20mm granite (of any type) tiles machine cut, in skirting/dado laid over as as in shelves, partitions, cooking platform below granite stone and like incl necessary (of any type) 18-20mm (table top rubbed and polished) in steps, jambs, pillars, window cills, cooking platform, WHB platform and marble dust with admixture of pigment to match with marble shade incl 15mm thick screed bed and bedding of layer in CM 1:4 and making full curving the edges complete all as specified and as directed. |
| 47 | M&L for textured heavy duty exterior tiles of size 300x300x10mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match with existing floor and including 20mm thick screed bed and bedding of layers in CM 1:6 including demolition of existing tiles complete all as directed. Make;Jhonson endura textured design or equivalent of Kajaria/Somany. |
| 48 | S&F in repair aluminium anodised powder coated ventilator using rectangular tube of size 63.50 x 25 x 1.50 mm including 3.50 mm thick designer glass louvers and stainless steel wire mesh 0.36 mm nominal dia of wire, average width of aperture 1.40 mm using ‘Jindal” aluminium section complete all as specified and directed by Engineer-in-Charge. |
| 49 | M&L for factory made 100% solid wood plastic composite (WPC) door frame single rebated 90 mm x 45mm made from wood plastic composite (Single extruded process) material with density 780kg/ cum all as directed. Note:-During fixing of chowkat, surface shall be make good in plumb with existing finishes like cement plaster wall tiles, floor tiles etc and as per ans site requirement fixed with screws not less than 50mm on existing chowkats or timber framed work complete all as specified and directed |
| 50 | S&F for factory made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed |
| 51 | S&F for 125mm long aluminium anodised, barrel tower bolts of extruded section and fixed on door complete all as specified and directed |
| 52 | S&F for 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed on door complete all as specified and as directed. |
| 53 | S&F for 100mm size butt hinges, cast brass,with mild steel hinge pin, bright polished and fixed, type B-11 fixed on chowkat with brass/stainless steel screws complete all as directed |
| 54 | S&F for 125mm size extruded aluminium alloy handles, fabricated type,anodised fixed with screws on doors complete all as directed |
| 55 | S&F for 125mm size extruded aluminium alloy handles, fabricated type,anodised fixed with screws on doors complete all as directed |
| 56 | S&F in 15mm dia angle cock chromium plated with flange screwed for pipe and fixed on iron pipe complete all as directed Make: Essco or equvalent |
| 57 | S&F in 15mm dia chromium plated fancy type pillar tap with extension body with fly nuts capstan head screwed down high pressure with or without lettered Hot or Cold with long screwed shank fixed with wall flange and fixed on iron pipe complete all as directed Make: Essco or equvalent |
| 58 | S & F in brass Chromium plated soap dish , fixed to wall with CP brass screws, all as specified and directed. Make: Johnson Fusion series Cat part No: T3252C or of equivalent make as approved by GE |
| 59 | S & F in Brass Chromium plated towel rail all as specified and directed. Make: Johnson Fusion series Cat part No: T1350C or of equivalent make as per Appx 'A' as approved by GE |
| 60 | S&F in chromium plated gratings 100mm dia with drain hole all as specified and directed Make: ISI Marked or of equivalent make as per Appx'A' as approved by GE |
| 61 | S&F rotational moulded polyethene water storage tank 3 layer white colour water tank non toxic effect, algea formation protection (made from virgin grade of polythethylene material which is duly stablized with anti-oxidant plastic) of capacity 1000 Litres (cylinderical verticle one piece moulded with closed top) the internal and external surfaces of tank are smooth, clean and free from any hidden internal defects, hoisted and fixed in position including S&F necessary GI fittings, inlet/ outlet washout, overflow pieces long nipples, checknuts, washers & 20mm dia PTMT valves high pressure of PTMT epoxy coated aluminum rod&high density plastic ball and 20mm brass stop cock etc complete including dismantling of existing water tank all as specified and directed. Make:Sintex, Polycon, Rotex |
| 62 | M&L for machine cut kota stone slab flooring 10-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl rubbibg and polishing complete over 20mm thick screed bed or bedding the layer in CM 1:6 complete all as specified and directed |
| 63 | M&L 75mm thick PCC type C-2, 1:3:6(20mm graded aggregate) as in plinth protection alid in alternate bays n.exc 3.0m length,finished surfaces even and smooth without using extra cement complete all as specified and as directed. |
| 64 | S&F for glass dividing strips 3mm thick and 38mm width, inserted in position cofirm to design complete all as specified and as directed. |
| 65 | M&L for Point wiring using FRLS-H PVC insulated unsheathed, multistranded copper conductor cable 1.5 sqmm drawn through and including PVC conduit of min 20 mm dia by Cutting chases for concealed conduits and sinking's for boxes and making good to walls, floors etc for concealed conduit wiring with modular flush box metal of GI sheet minimum 1.2 mm thick (ISI Marked) with earth terminal for safety, flush metal GI box of required modules as per site requirement and modular plate with support frame white in colour (ISI Marked) of required modules, 3mm thick including all fittings i.e. tees, bands and junction boxes, screws etc. complete for One light/Fan point controlled by one switch 6 Amps one way using cable (1.5 Sq mm for phase and neutral and 1.5 sq mm earthing) Note:- (a) wiring shall be done by using colour coding (b) Earth wire shall be of green colour. |
| 66 | All as item No 65 above One 3 pin socket outlet, 5 Amp socket outlet on same board with other switches. |
| 67 | All as per item No 65 above but One 3 pin socket outlet, 5 Amp socket outlet on independent board. |
| 68 | Description all as per 65 here-in before but using 2.5 Sqmm single core copper conductor FRLS cable of multistranded PVC insulated unsheathed 1100 Volts grade for one 6 pin socket outlet plug point,16 Amps independent including necessary running of 2.5 Sqmm PVC insulated multistranded copper conductor single core FRLS cable as earth continuity conductor along with wiring and connecting to earth dolly providing Copper cable sockets plate/ bottle type of adequate size at termination end of cable point wiring in DBs, switch boards, fittings fixtures all as specified and as directed |
| 69 | Supply and fixing modular Switch fabio classic white series/ Switch fabio classic white with indicator, ISI marked 16 AX Amps One Way switch complete all as specified and directed. |
| 70 | Supply and fixing modular socket outlet fabio series 6 Amps 3 pin universal socket with child safety shutter, Shrouded terminals compatible with all standard mobile chargers, ISI marked for the same board complete all as specified and directed. |
| 71 | Supply and fixing modular socket (Fabio classic white) outlet 16 Amps shuttered socket (heavy duty) 3 pin unversal socket with child safety shutter, Shrouded terminals, ISI marked for the independent board complete all as specified and directed. (Make:Anchor/Roma/Havells/Legrand/Indoasian) |
| 72 | Supply and fixing modular Switch fabio classic white series/ Switch fabio classic white with indicator, ISI marked 6 AX Amps One Way switch complete all as specified and directed. (Make:Anchor/Roma/Havells/Legrand/Indoasian) |
| 73 | Supply and fix MCB DB SPN 8 way, IP - 43 Protection double door 240 V AC 50Hz with for MCB SPN as incomer and SP MCBs as out going with integrated door earhting system, with tinned copper bus bar ,neutral link earth link complete all as directed. Make: Legrand or its equivalent make Indoasian/Havells/Legrand/Anchor |
| 74 | Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) SPN 40 AMP and current carrying capacity in the MCB DB complete with connection testing and commissioning. Make Indoasian/Havells/Legrand/Anchor |
| 75 | Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) SP 5 To 32 AMP and current carrying capacity in the MCB DB complete with connection testing and commissioning. Make Indoasian/Havells/Legrand/Anchor |
| 76 | Supply and fixing modular Ceiling Ceiling rose, 3 phase/PVC/polycarbonate, isolated body 50 x 65 mm surface type complete all as specified and directed. |
| 77 | Supply and fixing 20/22 Watt Inverter LED Batten aluminium body with Opal Diffuser, IP20, Battery back-up & Functioning as per Product TDS with intregrated electronic driver, connector block, holder, decorative end caps, LED tube light etc complete with all accessories prewired and mounting PVC rectangular block, including provision of flexible copper conductor cable of suitable size from ceiling rose to connector and taking down old unserviceable fitting from existing postion for carrying to store, making good disturbed surfaces complete all as specified and as directed. |
| 78 | S & F for wall/ceiling mounted 10 watts or more indoor, box type light fitting white/ warm white as per site requirement, 230 volts with extruded aluminium heat sink provided for efficient heat dissipation and intregrated electronic driver connector block etc complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED tube 2' x 10 watts complete all as specified and as directed. |
| 79 | Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed. |
| 80 | S & F submain wiring with 2 single core (FRLS) PVC insulated unsheathed multistranded flexible copper conductor cable, of 4.0 Sqmm and one single core 4.0 Sqmm flame retardent low smoke (FRLS) PVC insulated, unsheathed, multistranded, flexible copper cable as earthing lead , all as per IS 694/1990 drawn through including concealed in stone masonary PVC conduit and conduit accessories heavy duty ISI marked, providing Copper cable sockets plate/ bottle type of adequate size at termination end of cable point wiring in DBs, switch boards, fittings fixtures all as specified and as directed all as specified a Note :- ( Two runs of main copper wire, one run of earth wire cable & PVC conduit shall be measured together as one length). (Make- Havells/Polycab/KEI/Finolex) |
| 81 | Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and directed |
| 82 | Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16.0 sq mm 2 core complete all as specified and as directed. |
| 83 | S & F LED down light recess mounted luminare, round type 15 watts with efficiency of 100 lumens per watt, sleek design aluminium housing polycarbonate diffuser white finish operating voltage 150 V-270 V AC, 50 Hz all as per Make- Philips Cat Part No DN172B LED9S-6500 PSU, jaquar nero plus LNRP01R012XN or Havells complete all as directed by Engineer- in-charge |
| 84 | M & L for Earthing complete with galvanised steel earth plate, electrode,600x600x6.0 mm thick burried directly in ground (earth pit not less than 2.25m deep below normal ground level) connected to GI strip 32x 6 mm thick dia by mens of nuts, bolts, & washers of GI as shown in electrical plate No. 5 of SSR Part-I Connected to earthing ten point all as specified and including necessary earth pit PCC 1:3:6 chanber be 50mm thick PCC 1:2:4 chamber cover with 6mm dia mild steel reinforcement of 10 cm c/c spacing both ways in lieu of CI cover , watering arrangement shall be made with GI pipe light grade of 20mm dia including funnel and protection to earth lead shall be provided with GI pipe light grade 15mm dia unto 7.5 from the earth plate electrode & refilling of soil etc including necessary excavation & earth work in any strata and PCC chamber all as specified and directed by Engr-in-Charge including demolish existing earth pit taking out old materials. |
| 85 | Supply and fix Single Door Three Phase 63 Amp IP44 Mini Feeder Pillar, TPN, 6 Way, Three Phase,Double Door, 440 V,TPN, IP44, Floor Mounted, Vertical type red in color double door floor mounted outdoor type, CPRI Approved as per IP-65 grade, made out of CRCA sheet 3.00 mm thick of outer body of suitable size with aluminium bus bar (50 x 10 mm ) should have danger notice for 415 volts, AC, mounted on 50x50x6 mm angle iron frame having minimum 2 feet ground clearance duly embedded in and including PCC block (1:2:4) type B-1 foundation for fixing of panel complete including termination of all incoming and outgoing cables with suitable size thimbles/lugs and glands, Nuts & Bolts, Washers complete |
| 86 | Supply and fix electric water heater, storage type Inner container material Steel with Glass and having 2 Nos Heating element type of Incoloy with Glass coated heating element upto 2 KW capacity 25 litre, 230 Volts 50 Hz , temp range 35 to 75 C, with 7 Years on Tank,4 Years on Heating Element and 2 Years on Other Parts, with Outer body material of ABS, PUF insulation, lined BEE 5 Star, with product dimension of 470x470x371mm rated vertical type complete with all accessories such as safety valve, thermostate, NRV, connection piece etc all as specified and directed by Engr-in-Charge. (Make ERICA DIGITAL : VOLUME 25 LTR of Jaquar or equivalent in Havells/Bajaj/Recold/Haier/Orient/Hindware) |
| 87 | Supply and fixing of geyser Bolt 120mm Long with nut & washers, complete all as specified and directed |
| 88 | S & F PVC rigid non-metallic flexible conduit ISI marked of dia 20 mm dia inclusive of all tees, bends, elbows reducers, junction box etc and fixing accessories such as couplers, lock nuts, saddles, etc for telephone cable , TV cable and public address system including where required all as directed by Engineer-in- Charge duly concealed in wall complete all as specified and as directed |
| 89 | Supply and installation of high-quality, durable material suitable for hot water applications 2 feet PVC connection for geyser, including all necessary fittings such as appropriate joints, couplings, or elbows as required for the installation, connections, and accessories including complete installation, testing, and making good of the site directed by Engineer-in- Charge complete all as specified and as directed |
| 90 | Supply and fix Sheet metal Enclosure with socket plug top and MCBs Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of 20 Amps, 240 Volts 50 Hz all as specified Engineer-in- Charge complete all as specified and as directed |
| 91 | Material and labour for point wiring using approved colour coding as per IS ,with multistranded copper conductor 4 Sqmm (nominal area), two single core, PVC insulated and unsheathed FRLS cable 1100 Volts for one 3 pin socket outlet plug point,20 Amps independent grade ISI-694 marked drawn through in and including heavy duty PVC concealed conduit including all accessories, Metal flush box of suitable module, with earth dolly, covered with twin colour (specified by Engr-in- Charge)modular white cover plate & frame after chasing in stone masonry walls etc for accomodating modular switches, sockets, regulators etc including PVC insulated multistranded copper conductor 4 Sqmm (nominal area) single core FRLS cable as earth continuity conductor along with wiring and connecting to earth dolly, providing Copper cable sockets plate/ bottle type of adequate size at termination end of cable point wiring in DBs, switch boards, fittings fixtures all as specified and as directed. |
| 92 | Supply and lay pipe galvanized, “Medium class”, including fittings, 25 mm (1”) dia. . Make : TATA/JINDAL or equivalent |
| 93 | Supply and fixing gun metal gate valve with iron head wheel head screwed both ends for iron pipe and fixed on 25 mm dia all as specified and directed. |
| 94 | M&L for cutting the existing GI tubing of size 40/32 mm dia for taking new connection of 25mm dia GI pipe complete withall fittings all as specified and directed. |
| 95 | M&L for 20mm thick plastering in two layers of CM 1:6 on brick or concrete wall surfaces etc with 2% of WPC on cement complete all as directed.(Note:WPC shall be measurned and paid in separatetly) |
| 96 | Supply only integral water proofing compound |
| 97 | M&L for PCC (1:3:6) type C2 ( using 40mm graded broken stone aggregates) as in bed to drain pipes incl packing under and haunching against the sides of pipes after they are laid and tested for 150mm bore of pipe complete all as specified and as directed. |
| 98 | M&L in 150mm bore RCC pipes, class NP2 laid and jointed with collars and tested drain pipes (salt glazed earthern ware, AC or reinforced concrete), set in cement mortar complete all as specified and as directed. |
| 99 | M&L for cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in PCC (1:2:4) type B-1, smooth finished and reforming benching as required for 150 mm internal dia of pipe complete all as specified and as directed. |
| 100 | S&F in repair for factory made 50 mm thick, 900mmX650mm manhole cover with additional frame for fixing, of precast RCC 1:2:4 type B-1 (using 20mm graded stone aggregate) finished the surface even and fare incl reinforcement MS TMT bars 6mm dia @ 150mm centre to centre both ways and set in CM 1:4 and handles including demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position complete all as specified and as directed. |
| 101 | Excavating in post holes (or similar holes) each n exc 0.5cu. m, getting out, returning,filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25 cm for soft/loose soil. |
| 102 | M&L for PCC 1:2:4, type B-1 (20mm graded agg) as in roof kerbs or mud stops, rounded or chamfered on edges, filling footing foundations, mass concrete and similar works etc to complete all as specified and as directed. |
| 103 | M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work; vertical or to batte |
| 104 | M&L for old size brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as speified and directed |
| 105 | S&F for mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and as directed. |
| 106 | M&L for broken stone or boulders Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and rammed to a true surface complete all as specified and as directed. |
| 107 | M&L for 100mm thick PCC type D- 2, 1:4:8 (40mm graded aggregate) as in sub base/plinth protection etc complete all as specified and directed |
| 108 | M&L for machine pressed precast cement concrete coloured interlocking paver blocks, glossy rubber moulded, of triangular / Zigzag / Haxagone/any shape/design and size as approved, 80mm thick, conforming to IS 15658-2006, M-35 with grey cement and pigments grade in floor/ paths/ pavement laid over and including 25mm thick sand cushioning laid dry to the profile including filling the joints with sand incl dismantling of existing tiles of any description complete all as specified and as directed. NOTE: (i) Manufacturers test certificate shall be submitted alongwith sample. |
| 109 | M&L for 20 mm thick cement plaster in CM 1:6 on bricks on concrete surfaces finishing the surfaces even and smooth without using extra cement with two coats of cement base paint on new surface complete all as specified and as directed. |
| 110 | S&F in white counter top Basin (self-rimming) Oval shape of size 550mm x 430mm x 195 mm fixed in position including waste coupling and PVC waste pipe, 32mm dia. complete Make: Parryware Model Aquarius, Cat Part No – C0466(SP) or of equivalent make |
| 111 | S&F in automatic ABS basic hand dryer(Make: dolphy Model No DAHD0011) of size 240x230x240mm complete fixed to wall complete all as specified and directed |
| 112 | M&L for vitreous china premium/ 1st quality Jaguar of size 370x670x720mm UF soft close slim seat floor mounted wash down water closet EWC white/ ivory/off white incl dual flush cistern fittings, health faucet alongwith two way bib cock and accessaries complete all as specified. Make: Jaguar Model No LYS-WHT-38851S300 UFSMN |
| 113 | S&F for Jaguar vitreous china urinal half stall type (Cat Part No WHT-13261H) white or coloured including push cock and urinal spreder bowl top inlet with fixing stud connected to GI pipe etc complete all as directed. |
| 114 | S&F for Jaguar Basin Urinal Partition(Cat Part No JSE CHR-810UF60H19X ) including stinless steel brackets or necessary fixing on wall complete all as directed. |
| 115 | S&F in 5mm thick bevelled edge looking mirror of size 1.20m x 0.80m fixed to wall with statinless screw with cap head complete all as specified and directed |
| 116 | S&F in aluminium powder coated fancy type decorative type curtain rod 25 mm bore complete all as specified and as directed. |
| 117 | S&F in aluminium powder coated fancy type decorative brackets suitable for 25 mm dia curtain rod (minimum projection from wall 75 mm ) fixed to wall including drilling, rawl plug, screws etc complete all as specified and as directed. |
| 118 | M&L for 100mm thick breaking brick or similar hardness materials or boulders to 63 mm gauge as in sub base complete all as specified and directed |
| 119 | M&L for double charged anti - skid ceramic tiles of each tile of size 600mm x 800mmx 8-10mm thick in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 15mm thick screed bed or bedding of layer in CM 1:6 complete all as specified and as directed. |
| 120 | M&L glazed ceramic coloured tiles of size 600 x 300 x 7-8mm thick, on vertical surfaces of walls such as skirting dado etc. set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick rendering in cement mortar 1:3 complete all as specified and as directed. |
| 121 | S&F Factory made 100 % solid wood plastic composite(WPC) door frame, double rebate 125 mm x 45 mm made from wood plastic composite ( Single extruded process) material with density 780 Kg/ Cum, all as specified and directed.NOTE: During Fixing of chowkhat, surface Shall be make good in plumb with existing finishes like cement plaster, similar wall tile,floor tile etc and as per site requirement. |
| 122 | S&F in Pillar cock swan neck suitable for 15mm bore pipe long body fancy type brass CP with Capstan head screwed down screwed for iron pipe or brass ferrule quarter turn complete all as specified. Make: Johnson Cat Part No T2804C Magna SERIES or of equivalent |
| 123 | S& in chromium plated bib cock with wall flange quarter turn complete all as specified and as directed. Cat No. FUS-29037 of make Jaquar ‘Fusion' series or of equivalent make as per Appx 'A' as approved by GE. |
| 124 | S&F in angle cock with flange quarter turn chromium plated cast copper alloy ISI marked, high pressure screwed down complete all as specified. Make: Johnson Eco Cat part No: T3910C or of equivalent make as per Appx 'A' as approved by GE. |
| 125 | S&F in chromium plated hand rail at bath room for senior citizen fixed on wall complete all as directed Make: ISI Marked or equivalent |
| 126 | S&F CP towel rail 600 mm long fixed with and including chrome plated brass screws and wooden/plastic cleats complete all as specified and directed. |
| 127 | S & F in Brass Chromium plated towel ring all as specified and directed. Make: Johnson Fusion series Cat part No: T1351C or of equivalent make as per Appx 'A' as approved by GE |
| 128 | S & F rotational moulded polyethylene water storage tank 3 layer white colour waterr tank , non- toxic effect, algea formation protection (made frome Virgin grade of polyetjylene material which is duly stablized with anti-oxident Plastic) of capacity 500 litres, (cylindrical vertical one piece moulded with closed top), the internal and external surfaces of tanks are smooth, clean and free from any hidden internal defects, hoisted and fixed in position including S & F necessary GI fittings, inlet/outlet washout, overflow pieces long nipples, checknuts & washer, 20mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Min weight 210gms) and stop valves for 20mm bore pipe, cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends etc complete all as specified and directed. MAKE :-SINTEX |
| 129 | S&F 605 x 605 mm grid for Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. complete all as specified and directed. |
| 130 | S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified complete all as specified and directed. |
| 131 | M&L for Providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wire mesh (Fillets, metal frame work and G.I. wire mesh paid separately) |
| 132 | M&L for preparation of new ceiling surfaces and two coats of oil bound distemper over a coat of primer complete all as specified and directed |
| 133 | M&L for 20mm thick plastering in two layers of CM 1:6 on brick or concrete wall surfaces etc with 2% of WPC on cement complete all as directed.(Note:WPC shall be measurned and paid in separatetly) . |
| 134 | Material and labour for point wiring using approved colour coding as per IS ,with multistranded copper conductor 1.5 Sqmm (nominal area), two single core, PVC insulated and unsheathed FRLS cable 1100 Volts grade ISI-694 marked drawn through in and including heavy duty PVC concealed conduit including all accessories, Metal flush box of suitable module, with earth dolly, covered with twin colour (specified by Engr-in- Charge)modular white cover plate & frame after chasing in brick masonry walls etc for accomodating modular switches, sockets, regulators etc including PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLS cable as earth continuity conductor along with wiring and connecting to earth dolly, providing Copper cable sockets plate/ bottle type of adequate size at termination end of cable point wiring in DBs, switch boards, fittings fixtures all as specified and as directed for the following (Make- Finolex/ Anchor/ Grandlay/ Polycab/L&T) |
| 135 | One 5 pin socket outlet plug point, 6 Amps, controlled by one, switch on same board complete all as specified and as directed |
| 136 | One 5 pin socket outlet plug point, 6 Amps, controlled by one, switch on independent board complete all as specified and as directed |
| 137 | S & F Modular socket outlet fabio series 6 Amps 3 Pin universal socket with child safety shutter, multipurpose complete all as specified and as directed. (Make:Anchor/Roma/Havells/Legrand/Indoasian) |
| 138 | Supply and fix in repair for wall mounted LED 18/20 watts with lumens out put not less than 2000 lumens white/ warm white, box type (decorative) light fitting, 230 volts with extruded aluminium heat sink provided for efficient heat dissipation and integrated electronic driver connector block etc complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED tube 4' x 20watts complete all as specified and as directed. Make: Halonix Cat part No HLB-03-18-CW-AL Bajaj Cat No. BCLAB 20W, JAQUAR Cat part No LGLZ01X020XN or equvalent of make Philips/ as approved. |
| 139 | S & F in repair for wall mounted 18 watts indoor Inverter batten with opal diffuser, IP 20, with 4 hrs back up with out put of 1800 lumens , box type (decorative) light fitting, 230 volts with extruded aluminium heat sink provided for efficient heat dissipation and intregrated electronic driver connector block etc complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED tube 4' x 18 watts complete all as specified and as directed. Make :- Halonix Cat part No. LED INVERTER BATTEN HLB-08-18-CW-INV or equivalent Philips |
| 140 | S & F for plastic body exhaust fan, AC single phase, 240 V of size 250 mm sweep with louvers (as per Cat Part No -698502 of Make Indo Asian or equivalent Make- Bajaj Maxima DX/ Usha Crispair )including necessary connection and replacement of flexible copper cable from ceiling rose and taking down of old unserviceable fan complete all as specified and as directed |
| 141 | Note : 1. Performance security:- Refer Condition 22 of Special Conditions. 2. Quoted Contract Sum shall be arrived at after deducting the amount of Credit Schedule (refer Schedule of Credit in pdf form for quantity, rate and amount etc.) for old unserviceable materials retrieved from site. Please Enable Macros to View BoQ information |
