|
| 1 | Earth work in excavation in foundation, trenches etc. includingdressing of sides and ramming of bottoms, including getting out the excavated material, refilling after laying pipe/ foundation and disposal of surplus excavated material at a lead upto 50m suitable site as per direction of Engineer for following depths, below natural ground / Road top level. In all types soils/ saturated soil such as moorum, sand, sandy silt, clay, black cotton soil, kankar, etc. Depth upto 1.5 m |
| 2 | Carriage of Materials by mechanical transport including loading, unloading and stacking :: Earth 5Km |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level : 1:5:10 (1 cement : 5 fine/ coarse sand : 10 graded stone aggregate 40 mm nominal size) |
| 4 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level.1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 5 | Earth filling with available surplus soil excavated from foundations and taken only from outside of building plinth in layers not exceeding 20cm in depth, consolidating each deposited layer including ramming and watering and consolidation with lead up to 50 m and lift upto 1.5 m. |
| 6 | Random rubble masonry with hard stone in foundation and plinth : Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 7 | Cement plastering including T&P, scaffolding, material and complete labour, including cost of water, curing, racking of joints etc. with 20 mm cement plaster of mix : including Providing /mixing of synthetic fibers compulsorily complying with IS 16481:2022 of 06 mm/12 mm length to be mixed @ 0.25% by weight of Cement i.e. 125 gms per 50 kg Cement up to 900 gms per cum of Concrete/ mortar 1:6 (1 cement : 6 fine/ coarse sand) |
| 8 | Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm). |
| 9 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work |
| 10 | Providing and fixing of 60mm thick precast cement concrete interlocking paver block casted with rubber moulds in approved reflective colour and design having minimum compressive strength of 300 kg/ sq cm. The CC paving blocks be laid on average 50mm thick bed of coarse sand and the joint is to be filled with fine sand. Laying procedure on compacted sub-base as defined. Complete job is to be executed as per the instruction of Engineer in-charge. The rates to be inclusive of all lead & Lifts etc. complete as per specifications. |
| 11 | Chequered precast cement concrete tiles 22 mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Ordinary cement without any pigment. |
| 12 | Providing and fixing precast cement concrete M-20 grade (Using mechanical Concrete Mixer) kerb stone top and bottom width 115 and 165 mm respectively, 250 mm high on 150 mm thick PCC M-10 grade foundation as per design, including fixing at site as per clause 408 of MoRT&H Specification including all material, labour, machinery, lighting, guarding and maintenance of diversion. |
| 13 | Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. |
| 14 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm +/- 5% total coated thickness (TCT), Zinc coating 120gsm as per IS: 277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I. seam bolts and nuts, G.I. plain and bitumen washers complete : Crimp curve |
| 15 | Supplying, erecting and fixing in position specified precast RCCbench made of RCC grade M-30 consisting of 2 Nos. “L” shapedbase support of thickness 100 mm back height 1000mm, front height 450 mm, base width 420mm and 5 Nos. RCC planks of size of 1500x100 x 50 mm and 1 Nos RCC planks of 150x200x50mm including joining all parts with galvanised nuts and bolts of suitable size. All bolts to be sealed after assembly with nice finish and appearance and level complete in all respect as per direction of engineer in-charge. Every bench should have a manufacturer’s logo of appropriate size Engraved at suitable place. |
| 16 | SKY WALKER :Area : - 1.72 Mtr x 0.63 MtrSafe Area :- 2.54 Mtr x 1 MtrProviding and fixing sky walker made from \\"B\\" class G.I. pipe. the main frame pipe is Ǿ 80mm made from \\"C\\" class G.I. pipe. the outer ring of sky walker is Ǿ 32mm made from \\"C\\" class G.I. pipe. for connecting the handle frame to main pipe Ǿ 60mm \\"C\\" class G.I. pipe is used. the bottom support of M.S. round plate of Ǿ 250mm x 10mm thickness is welded at bottom. the leg movement frame is of 50x50mmx2mm thick CRC square pipe. the handle frame is of Ǿ 40mm made from \\"C\\" class G.I. pipe. the foundation used for fixing is 80x40mmx3mm thickness C-channel. the footrests is made from aluminum casting material, its sizes are 130x310x5mm. closing caps made from top quality FRP material with 2mm thickness & plastic cap are used. the pins used are made up of Ǿ 25mm bright bar. the bearings used are \\"6205zz\\" & \\"6203zz\\"permanent lubricated sealed bering of reputed make SKF/FAG). high tensile steel with galvanized nut bolts are used for assembly. the serclips used for assembly are of Ǿ 25mm. the powder coat is done by poly urethane & epoxy powder with 60 to 70 micron thickness |
| 17 | LEG PRESS : Area :- 0.40x1.77 MtrSafe Area :-Providing and the center p The bottom support thickness is welded the remaining outer frame pipe. the foundation used for Ǿ 80mm made from \\"C\\" c & 10 mm thickness, 25mmx25mm. to join the c 3mm thicness isused. the seats are size .330mmx3mm and size 250 mmx 200mm. the footrests is made130mmx311.77 mtr.-1x2.38mtr. fixing leg press made from \\"B\\" class G.I. p pipe is of Ǿ 115mm made from \\"C\\" class G.I. of M.S. round plate of Ǿ 250mm & at bottom. is of Ǿ 40mm made from \\"C\\" class G.I. foundation fixing is consist of three equal class G.I. pipe, M.S. round p x 3mm M.S. angle. centrepipe & outer frame seamless pipe of thickness fitted on the outer frame is made up of FRP material of 300mm of thickness 3mm & M.S. plate of is used to support it. from aluminum casting material, i 10mm & 5mm thickness. pipe, made pipe and 250mm, 10mm items i.e. plate of Ǿ 250mm angle. Ǿ 120mm & thickness 5 support its sizes are the frame of footrests consists of Ǿ 32mm made from \\"C\\" class G.I. pipe. closing caps made from top quality FRP material which is of 2 mm thickness. the inner bushes is made from seamless pipe, itsdiameter is 60mm & 5mm thickness. the pins used in are made up of Ǿ 25 mm hardened bright bar, the bearings used are of \\"6205zz\\" permanent lubricated sealed bearing of reputed make (FAG/SKF). the handles used are of rubber grip. high tensile steel with galvanized nut bolts are used for assembly. the serclips used for assembly are of Ǿ 25 mm. the powder coat is done by poly urethane & |
| 18 | SIT UP BOARD :Dimensions : - 1820 mm (Length) x 430 mm (Width) x 580 mm (Height).Safe Area : - 2.8 Mtr x 0.6 Mtr.Sit up Board equipment made from \\"B\\" class G.I. pipe of different NB. NB stands for nominal bore sizes i.e. internal diameter of pipe in millimeters. The main frame is of 50 mm NB made from \\"B\\" class G.I. pipe supported with the M.S. round plate of Ǿ 250x10 mm thickness. Fibre reinforced plastic sheet of 3 mm thickness is bounded on 25 mm NB (G.I.) \\"B\\" class pipe of main frame. The base support of the sit up board is made 40 NB (G.I.) \\"B\\" class pipe. The foundation used for fixing is structure and made from center pipe of G.I. of 80 NB \\"B\\" class welded with M.S. round plate of Ǿ 250 mm & 10 mm thick mainpipe. Supported with 25 mm x 25 mm M.S. angles of 3 mm thickness and 20 mm x 40 mm CRC square pipes of 3 mm thickness. The powder coating is done with pure polyester powder Ackzonoble or Berger paints with 60 to 70 micron thickness. |
| 19 | ROWER :Area :- 1.2 x 1 MtrSafe Area :- 1.5 x 1.5 MtrProviding and fixing rower made from \\"B\\" class G.I. pipe. the main frame is of 80mmx40mm & 40mmx40mm CRC pipe with 2 mm thickness. the handle frame is of Ǿ 32 made from \\"C\\" class G.I.pipe. the foundation used for fixing consists of three equal items i.e. Ǿ 40mm made from \\"C\\" class G.I.pipe, c channel of 75mmx40mmx5mm & 25mmx25mmx3mm M.S. angle. to join themovement frame to main frame seamless pipe of Ǿ 50mm & 3mm thickness is used. the seats which are fitted on the main frame is made up of high quality FRP material of size 330mmx300mm of thickness 3 mm & M.S.plate of size 250mmx200mmx5mm is used to support it. closing caps are made from top quality FRP material which is of 2 mm thickness. the pins used are made up of Ǿ 17 mm hardened bright bar. the bearings used are of \\"6203zz\\" permanent lubricated sealed bearing of reputed make (FAG/SKF) the handles used are of rubber grip. high tensile steel with galvanized nut bolts are used for assembly. the bushes (Stopper) used to avoid the collusion. the serclips used for assembly is of Ǿ 17 mm. the powder coat is done by poly urethane & epoxy powder with 60 to 70 micron thickness. |
| 20 | SURF BOARD :Diamensions :- 910mm (Length) x 860mm (Width) x 1400mm (Heigth)Safe Area :- 1.39 x 1.27 Mtr.Surf board equipment made from \\"B\\" class G.I. pipe of different NB.NB stands for nominal bore sizes i.e. internal diameter of pipe in millimeters. The center pipe is of 100mm NB made from \\"B\\" class G.I. pipe. The sleeve pipe is of 125mm OD seamless pipe with thickness of 5 mm and bolted to main frame with M 10 SS bolts.The bottom support welded of M.S. plate of Ǿ 250mm & 10mm thickness. The handle frame is of 25 NB made from \\"B\\" class G.I. pipe.The paddle frame is of 50 NB made from \\"B\\" class G.I. pipe is supported with 70x8mm bend M.S. flat and can be replaceable.the foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB \\"B\\" class welded with M.S. round plate of Ǿ 250 mm & 10 mm thick. main pipe supported with 25 mm x 25 mm M.S. angles of 3 mm thickness and 20mmx40mm CRC square pipes of 3 mm thickness.Bushes are used 70mm outer diameter with 5mm thickness is used.the footrests made from injection moulded plastic LLDPE/HDPEfor support to footrest 200mmx250mm with 3 mm thickness M.S. plate used. Closing caps are made up of injection moulded plastic LLDPE/HDPE. The pins used are made up of Ǿ 35 mm SAE 8620 bright material. The bearing used are of \\"6007zz\\" permanent lubricated sealed bearing of reputed brand.High tensile steel with galvanized nut bolts are used for assembly.The cerclips used for assembly is of A 34.The powder coating is done with pure polyester powder of Ackzonoble or |
| 21 | berger with 60 to 70 micron thickness.2.00 32100.00 each 64200.007 AIR WALKER :MACHINE PART DESCRIPTION OF THE AIR WALKER(a) Mounting plate (b) Center pillar (c) Trapezium shaped pipe(d) Cap (e) Holding pipe (f) Hinge supporter(g) Obtuse L shaped pipe (h) Rectangular pipe(i) Standing pad (j) Triangular hinge supporter1 A circular mounting plate of diameter 233mm and thichness 8mm, 4 holes on this plate at 90 degrees of which P>C.D. 170mm hole diameter is 20mm.2 On circular mounting plate a center pillar is welded. Diameter of center pillar is 114mm and height is 233mm.3 Trapezium shaped pipe is welded to the center pillar from the middle at the base. Trapezium shaped pipe's upper portion is open with two branches.4 Cap is on the two branches of upper portion/top of the branches are 925mm wide and length of each branch is 885m. At the base of the branches the gap is925mm with a radius bend 235mm.5 Open end of Trapezium shaped pipe is welded with a holding pipe. Holding pipe has a straight length of 810mm and a 90 degrees radius on the both sides,then a small straight length of 246mm. throught this small straight lengthholding pipe is welded to trapezium shaped pipe. Holding pipe is welded at an angle of 40 degrees to the open ends of trapezium shaped pipem height of jointis 1212mm |
| 22 | TRIPE HIP TWISTER :MACHINE PARTS DESCRIPTION OF TRIPE HIP TWISTER :1 Mounting Plate2 Center Pillar3 Plastic Cap4 Circular Handle5 Connecting Rod6 Floor Rest Pipe7 Standing PadFOUNDATION OF MACHINE IS CEMENTED AND BOLTED WITHBASE CHANNEL AND CIRCULARMOUNTING PLATE WHICH DIMENSION IS BELOW :1 Measurement of base channel is 3'x6\\"x2\\"2 Circular mounting plate's diameter 233mm and thickness is 8mm. 4 hole on this plate at 90 degrees which P.C.D. is 170mm. Hole diameter is 20mm. MACHANICAL DIMENSION AND MEASUREMENT OF MACHINE ARE FOLLOWING :1 A circular mounting plate which diamension is same of above circularmounting plate and it is tightened with nut and bolt.2 On this circular mounting plate a center pillar is welded. Diameter of center pillar is 114mm and height is 1288mm.3 Plastic cap is fixed on the top of center pillar and tightened with help of screw. Diameter and height is 120mm and 69mm.4 Circular handle is welded at the height of 1171mm from the base of circular mounting plate. OD of circular plate is 557 and ID is 493mm. Three pipe rodwhich diameter 32mm are welded at 120 degree. |
| 23 | 5 Connecting rod for floor rest pad which diameter is 48mm. It is being bended2.00 30200.00 each 60400.009 CHEST PRESS CUM SEATED PULLER :Dimensions :- 2000mm (Length)x710mm (Width)x2200mm (Heigth)Safe Area :- 3.0 Mtrx1.7 Mtr.Chest press cum seated puller equipment made up of \\"B\\" class G.I. pipe ofdifferent NB. NB stands for nominal bore sizes i.e. internal diameter of pipe inmillimeters.The center pipe is of 100 NB made up of \\"B\\" class G.I. pipe.The bottom welded with support of M.S. round plate of Ǿ 250mm & 10mmthickness.The connecting pipes are made up from 25NB \\"B\\" class G.I. pipe.The handle frame is made up from 32NB \\"B\\" class G.I. pipe.To build structure bushes are used which are made from seamless pipe of 50mm O.D. and 6mm thickness as well as 50mm diameter solid bar is used. The foundation used for fixing is a structure and made from center pipe of G.I. of 80NB \\"B\\" class welded with M.S. round plate of Ǿ 250mm & 10mm thick. Main pipe supported with 25mmx25mm. M.S. angles of 3mm thickness and 20mmx40mm CRC square pipes of 3mm thickness. The seats and back rests are fitted on the outer frames are made up of M.S. sheet of size 330mmx300mmx2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20mm with no sharp edges. Closing caps are made up of injection moulded p |
| 24 | MULTI FUNCTIONAL TRAINER :(Single User)Machine Part Description :-1 Mounting plate 12 Cap3 Handle connecting pipe 14 Connecting pipe 15 Center pillar6 Holding pipe 17 Holding pipe 28 Movable pipe9 Square pipes10 Stepping plates11 Stepper base12 Standing plate13 Center pipe14 Mounting plate 215 Handle connecting pipe 216 Nylon pad17 Hinged pipe 118 Hinged pipe 2 |
| 25 | SHOULDER BUILDER :Mounting plateCenter pillar2 hinge holding pipe2 bending pipeCap2 u shapped pipesHandles2 straight pipe (No.-1)Straight pipe (No.-2)Straight pipe (No.-3)Seat base pipeSeat bending pipeSeatBack seatHinge boxBracket holder1 A circular mounting plate of diameter 233mm and thickness 8mm, there are 4holes on this plate at 90 degrees which is P.C.D. 17mm, hole diameter is 20mm.2 On circular mounting plate a center pillar is welded. Diameter of the centerpillar is 119mm and height is 1838mm.3 Cap is fixed on the top of the pillar with rivets.4 At 1528mm vertical distance-2 hinges holding pipes are welded in oppositedirections. Hinge holding pipes have clear hole for screw at 177mm distance.5 Bending pipes are welded to the hinge holding pipes and the center pillar toprovide mechanical strength to the hinge holding pipe. |
| 26 | 6 Hinge box is fitted to the hinge holding pipes with a steel screw and bush. 2.00 32180.00 each 64360.00 12 CYCLE : Dimensions :- 1570mm (Length) x 570mm (Width) x 900mm (Height) Safe Area :- 2.5 Mtr x 1.5 Mtr Cycle equipment made from \\"B\\" class G.I. pipe of different NB (NB stands for Nominal Bore size i.e. Internal Diameter of pipe in millimeters)The main frame of 50 NB made from \\"B\\" class G.I. pipes.M.S. round plate of Ǿ 300mm & 10mm thickness used to form a paddleassembly. The handle frame is of 25 NB made from \\"B\\" class G.I. pipe.The seat and back rests are fitted on the outer frames are made up of M.S. sheet of size 330mmx300mmx2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20mm with no sharp edges. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB \\"B\\" class welded with M.S. round plate of Ǿ 250mm & 10mm thick main pipe supported with 25x25mm M.S. angles of 3mm thickness and 20mmx40mm CRC square pipes of 3mm thickness.Closing caps are made up of injection mounlded plastic LLDPE/HDPE.Pins used of Diameter 25mm are made up from SAE 8620 bright material. Pins used of Diameter 13mm are made up from ENB material with CRCA pipe 20x20mm of thickness 3.00mm for paddle assembly.The bearing used are 6001zz & 6205zz permanent lubricated sealed sealed bearing of reputed brand. High tensile steel with galvanized nuts and bolts are used for assembly. The circlip used for assembly are of A24 type. The powder coating done with pure polyester powders from Ackzonoble orberger paints with 60 to 70 micron thickness.2.00 32200.00 each 64400.00Total Part B Please Enable Macros to View BoQ information |
