|
| 1 | Works |
| 2 | Providing and laying PLAIN CEMENT CONCRETE 1:2:4 (1- Cement : 2- Coarse sand : 4- graded stone aggregates 20 mm nominal size) in foundations and superstructure including, machine mixing, leveling compacting, curing and formwork if any, scaffolding, staging etc. complete as directed and instructed by Engineer-in-Charge. Volume of PCC laid to be measured for payment. |
| 3 | Providing material & labour for laying Rebar in Existing Column, Beam and Slab including all dia. Of bars 8mm to 32mm as per drawing and specification as directions of Chief Engineer in charge Complete. Make Hilti or Fischer or its equivalent as approved by engineer-in-charge |
| 4 | Providing, laying and fixing in position REINFORCEMENT High yield deformed bars/TMT/ FE500/FE500D/FE550 for R.C.C. works at all levels including cutting, bending and binding with 16 gauge M.S. annealed wire, providing cover blocks of C.M. 1:2 Embedded with binding wire etc. complete. The reinforcement detailing to IS 456 or, if specified by engineer, shall conform to IS: 13920 (Ductile detailing of R. C. Structures), bars as per IS 1786 the rate shall be inclusive of executing such detailing. Laps to be measured shall be as shown in drawing and for reinforcement length longer than available in market. Chairs, pins and laps other than that specified shall not on be measured and paid for. No extra to be paid for height, rate remains same at all levels, complete as per drawings, specification, direction of engineer-incharge. Make: TATA, SAIL, JSW or as approved by engineer-in-charge Complete. |
| 5 | Providing & fixing White stone Bela masonry Block in course in super structure with stone of approved guality in Cement Mortar 1:5 (1-Cement : 5- course sand) including Racking the joints etc. complete |
| 6 | Providing and laying 10mm thick in single coat CEMENT PLASTER in (i)Cement mortar 1:3 (1-cement:3-sand) at all height/all floors to internal surfaces of all elements, walls, R.C.C. work, Ceiling,[backing coat at places where glazed or ceramic tiles are to be fixed etc]. including hacking of concrete surfaces, racking of joints, scaffolding, curing etc. complete. Final finished surface shall be little rough , so as it has proper bonding to paint putty.The surfaces to be plastered to be hacked immediately on de-shuttering. The Brick/ RCC surface to be plastered to be cured sufficiently before start of plaster. Initial bare surface area to be Plastered shall be measured for payment unless noted otherwise, etc as directions of Engineer in charge Complete. |
| 7 | Providing and laying 20mm thick SANDFACED CEMENT PLASTER of required grain finishing upto all height/all floors including grooves, pattas etc. in two coats having the the base coat of not less than 12 mm thickness in CM 1:3 (1-cement : 3-sand) & finished coat 8 mm thk, in CM 1:1 (1-cement : 1-sand) to external surfaces of concrete & masonry including hacking of concrete surfaces, racking of joints, scaffolding, curing etc. complete. Rate shall include addition of “Impermo” water proofing compound or equivalent, providing, adding & mixing of fine fibrillated 100% virgin polypropylene fibers in cement mortar to form homogeneous mixture @125 gms per a bag of cement in both the coats of plaster, 12mm long fibers shall be used in first coat & 6mm long fibers shall be used in second finished coat. providing drip mould 40mm wide and 12mm thick in cement mortar 1:3 on soffit of chajjas, canopies, gutters etc.complete. as directions of Engineer in charge Complete.The surfaces to be plastered to be hacked immediately on de-shuttering. The Brick/ RCC surface to be plastered to be cured sufficiently before start of plaster. Initial bare surface area to be Plastered shall be measured for payment unless noted otherwise, etc as directions of Engineer in charge Complete. |
| 8 | Providing material and labor for applying Two coats of acrylic putty upto desired thickness for getting undulation free surface and accurate plumbness in walls. including providing grooves as per architectural drawings at all the edges of windows/Doors with neat finish on new/existing wall surface Work includes surface cleaning, removal of loose particles, minor leveling, and application of putty in one or more coats to accurately achieve the required thickness. After proper curing, the surface will be sanded to a smooth, even finish suitable for painting. Thickness will be checked for accuracy throughout the application to ensure compliance with project specifications. |
| 9 | Providing material & labour for Internal Wall painting (two coats) with Premium Emulsion of approved brand and manufacture including primer coat on undecorated wall surface to give an even shade including throughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth. as directed by engineer in charge complete. emulsion that must offer protection against different varieties of bacteria and fungus.The product shall be independently tested and approved for properties alike resistance to bacterial and fungal species, crack tolerance and flame spread resistance.The coating shall contribute to satisfying the following credit(s): Indoor Environmental Quality (IEQ) under LEED® 2009 Environmental Quality (EQ) and Materials and Resources (MR) under LEED® v4This product shall have a VOC limit not more than 24 g/lit. The product can be like Asian apcolite emulsion or Jotun Paints or approved equivalents.Two Coats of above paint should be applied using conventional Roller / Airless spray at the site after application and drying of applied Putty-Primer. For measurement of painting items the area painted shall be considered without any multiplication factor for different kinds of surfaces painted. Rate shall be quoted accordingly. All painting items final finish shall be as per manufacturer'sspecification as per acceptance of Engineer in charge /Architect. No extra payment shall be made for extra/over coat if required.The rate shall be inclusive of providing bamboo scaffoldingMake: Jotun,Asian Paints, Berger Paints, Dulux Paints or equivalent. |
| 10 | Supplying & Providing two coat of primer and two coats of Texture paint, ANTIFUNGAL PAINT, water proof, dust proof Paint on Exterior Surfaces at all heights of surfaces. One component waterborne 100% pure acrylic emulsion that offers protection against concrete carbonation with an R Value of min 600m and an equivalent concrete layer thickness value of min 150cm. Paint should have crack bridging property of min 1.85 mm with Solar Reflective index of min 110 and IR reflectance property. The product shall have a Volume Solids of minimum 35%The product shall be independently tested and approved for properties alike Carbon Dioxide Diffusion resistance, resistance to chloride diffusion, crack bridging and liquid water/ vapour transmission as well as SRI properties. The product can be like Jotashield WaterXtreme Topcoat of Jotun Paints or approved equivalents.Two Coats of above paint should be applied using a conventional Roller / Airless spray at the site after application and curing of applied Primer.including cleaning, preparing the surface, applying primer - scraping by sandpaper, scaffolding etc. including - (a) All surface preparation, suitable number of base coats required, primers and suitable finishing to the complete satisfaction of the Engineer in Charge, (b) Scaffolding and all leads and lifts,(c) Proper curing in between the two subsequent coats, (d) Touch ups to the paint after the scaffolding is removed, (e) All measurements for paints to be as per IS-1200. f) Minimum Guarantee of Ten Years Waterproofing and Paint performance for all external paints by manufacturer .For measurement of painting items the area painted shall be considered without any multiplication factor for different kinds of surfaces painted. Rate shall be quoted accordingly. All painting items final finish shall be as per manufacturer'sspecification as per acceptance of Engineer in charge /Architect. No extra payment shall be made for extra/over coat if required.Make - Asian Paint Ultima Allura Torino, Jotun Jotashield Tex Fine OR Equivalent. |
| 11 | Providing and applying first quality oil-based synthetic enamel paint by spray method of approved brand and shade, conforming to relevant IS standards (IS 2932 / IS 1477), on steel/metal surfaces, complete as per specifications.The work shall include:-Thorough surface preparation by cleaning, scraping, and removing rust, dust, grease, and loose mill scale using emery paper/wire brush-Application of one coat of approved primer (red oxide / zinc chromate / zinc phosphate) suitable for steel-Application of two or more coats of oil-based synthetic enamel paint by spray gun to achieve smooth, uniform, and high-gloss finishThe paint shall be applied using air spray/pressure spray equipment, ensuring:-Even film thickness-Smooth, streak-free and brush-mark-free finish-Proper adhesion and coverageThe enamel paint shall have:-Hard, durable, and glossy finish-Resistance to weathering, moisture, and mild chemicals-Good opacity and colour retentionThe work includes all materials, labour, spray equipment, thinners, and surface preparation, complete in all respects as per directions of the Engineer-in-charge. |
| 12 | ALUMINIUM WORKS -Doors and Windows workProviding material and labour for fixing in position frames, shutter for any type of aluminium work for any type of door, window, partition, made out of any type of aluminium sections of approved make having minimum 50 micron pure polyester powder coating of approved shade, texture & colour of approved make for all floors, all levels, all heights, all shapes, all sizes including cutting, bending, crimping, fabricating in best workmanship manner etc as per the drawing, specification and as directed by Architect or Engineer-in-Charge. Contractor shall prepare shop drawing based on concept drawing and get approved from the consultants before procurement of material. All loose material shall be approved. Mockup of one/two window shall be executed as per approved shop drawing with all hardware. Work shall carried out as per the approved shop drawings, approved mock-up and approved sample. Actual weight of installed Aluminium sections (for using fabrication without considering any wastage) shall only be measured and shall be considered for the payment. Glazing shall be paid as seperate item. Contractor shall provide guarantee for stability, water tightness etc for 12 months after defects liability period. Rate shall be inclusive of providing aluminium sections, cutting, fabrication, errection and fixing to the best workmanship manner, including 1) Sheet metal screws and casted solid aluminum corner cleats fixed with external byttins with a spring for rapid and secure joint assembly for casement and sliding shutter and frame; 2) Glazing clips for receiving infill panel; 3) Best quality wool pile where ever shutter touches the frame and compatible microwave cured EPDM rubber; 4) Dash Anchor fasteners of HILTI HRDUGT or equivalent for fixing the frame assembly to the RCC or masonry surfaces. Minimum 1 anchor fastener shall be used for every 600 mm length of section for stability of frame. 5) 10mm GI tie rod for connecting vertical stile at top and bottom for aluminum door shutter and 4mm thick solid aluminium corner cleat of full thickness of section for connecting style and horizontal rails; 6) providing and fixing packing (rough ground) in full periphery/ at every 600mm c/c with average 6 mm thick PVC spacer/ compact sheet of width (equal to section width less 30mm for backer rod and sealant); 7) Filling the gap between wall and frame on both sides (outside and inside) with polyethylene baker rod of avg. 10 mm thickness of approved make and color and then sealing the remaining gap with neutral grade G/M (Glazed & Metal) weather silicon sealant of approved make and color. 8) Termite treated seasoned teak wood as infill material to installe hardware in door shutter and frame as and when required, etc as per directions of Engineer in charge Complete. Make:- Jindal or equivalent as approved by Engineer-in-charge |
| 13 | Providing and fixing Stainless Steel Mosquito Mesh for sliding windows, including all materials, accessories, tools, labour, transportation, complete as per specifications mentioned below:The mosquito mesh shall be made from Stainless Steel of Grade SS 304, woven type, with a wire diameter between 0.30 mm and 0.36 mm. The mesh opening shall be 16×16 or 18×16 per square inch, ensuring proper ventilation and high visibility with minimum 60% airflow. The mesh shall be corrosion-resistant, rust-free, and suitable for use in humid, dusty, and coastal environments. Finish shall be in natural stainless steel.The mesh shall be fixed in a separate aluminium sliding frame if required, matching the existing window sections. Suitable aluminium sections with provision for rubber beading shall be used. The mesh shall be held firmly using EPDM or neoprene gasket to ensure tight and uniform fixing, without sagging or wrinkling. All edges of the mesh must be properly crimped and trimmed to avoid sharp edges.Sliding arrangement shall operate smoothly on rollers if a separate shutter is provided. Anti-rattle and anti-dust brush strips shall be provided at the required edges. The design shall allow easy cleaning of the mesh from inside without dismantling the frame.The installed mesh shall prevent the entry of insects, mosquitoes, and dust. It shall withstand routine cleaning through wiping or brushing, without deforming, loosening, or corroding. Mesh must maintain shape and visibility throughout its service life. Minimum lifespan shall be 10 years without rust.Installation shall be carried out with proper alignment, ensuring the frame is level and the mesh tension is uniform. No gap greater than 1 mm shall be allowed at any side.Payment shall be made on the basis of the actual finished area covered by the mesh, measured in square metres, based on clear opening dimensions.The contractor shall submit a product data sheet confirming SS 304 material, along with a physical sample of minimum 100×100 mm for approval before execution.A minimum one-year warranty shall be provided against corrosion, sagging, manufacturing defects, and installation faults.Rate shall include all materials, mesh, beading, labour, tools, fasteners, and incidental charges. |
| 14 | Providing and fixing 6mm thick one-way reflective float glass of approved make, colour and shade, installed in aluminium/UPVC/MS/wooden window frames, including all necessary accessories, labour and materials, complete as directed by the Engineer-in-Charge.The glass shall be 6mm thick float glass with one-way reflective coating, also known as vision-control or reflective glass, allowing one-way visibility during daytime. The glass shall be free from bubbles, scratches, waves, spots or manufacturing defects. The colour/shade such as blue, green, bronze, silver, smoke grey or any other shall be as approved.The one-way reflective coating shall be durable, non-peeling, scratch-resistant and vacuum-deposited or hard-coated. All glazing work shall comply with IS 14900 (Safety glass and glazed systems) and applicable provisions of IS 2553 (Part 1) for architectural glazing. Glass shall be cut to accurate sizes with machine-finished edges.The glass shall be fixed using EPDM rubber gasket, approved neutral-cure silicone sealant or snap-fit glazing beads, depending on the type of frame system. All sealing shall be dust-proof, water-tight and free from vibration gaps. Necessary accessories shall be corrosion-resistant.The scope includes cutting, wastage allowance, transportation, handling, scaffolding, installation materials and cleaning of glass after fixing. Protective film, if provided, shall only be removed after final inspection and approval.Measurement shall be taken in square metres (m²) of the actual glazed area fixed in position. The cost of window frames, beads or supporting systems shall be paid separately, wherever applicable.Approved makes include: Saint-Gobain, Asahi India (AIS), Guardian, Pilkington, Modi Guard, or another equivalent make as approved by the Engineer-in-Charge. |
| 15 | Providing and fixing roller blinds of approved make and shade for indoor windows, including necessary brackets, chain/spring-operated mechanism, end caps, screws, plugs, cords, and all accessories complete.Scope of Work:-Supply of high-quality fabric / PVC / polyester / blackout material of approved shade and pattern, suitable for indoor use.-Roller mechanism including spring or chain-operated system for smooth operation.-Fixing neatly inside or outside the window frame as directed by Engineer-in-Charge.-Adjustment and testing for smooth operation, proper alignment, and level positioning.-All materials, labour, transportation, tools, and sundries included. |
| 16 | Providing and fixing 35mm thick factory-made solid core door shutter with block board core construction, infill of solid wood strips/blocks placed edge to edge having wooden strips of pine wood or any softwood, seasoned and treated, core sandwiched between two veneers/face plywood layers on both sides. Door manufactured as per IS: 2209 / IS: 1659 and hot-pressed using BWP grade synthetic resin adhesive conforming to IS: 848. The shutter shall have continuous stiles and rails, properly pressed and bonded, with hardwood lipping/edge banding on all exposed edges, fixed using approved adhesive and machine-finished as per IS: 4020 (test requirements).The shutter surface shall be factory-prepared to receive 1mm thick synthetic decorative laminate conforming to IS: 2046 (laminate to be paid separately).The rate shall include: complete manufacturing, block board core, stiles/rails, edge lipping, adhesive, edge finishing, and quality compliance as per IS standards.Note: Decorative laminate finish, door frame and all architectural hardware (hinges, locks, handles, door stopper, tower bolts, etc.) shall be paid separately under respective tender items. |
| 17 | Providing and fixing first class seasoned teak wood door frame of size 150 mm × 75 mm, including supplying of wooden members, cutting, sawing, planning, shaping, making corner joints, fitting, fixing, polishing, and finishing complete as directed. The wood shall be well-seasoned, kiln or air dried, free from knots, cracks, sap, decay, termite and insect infestation. The frame shall be dressed, smooth finished and machine-planed to uniform thickness.The door frame shall be provided with necessary joints such as mortise and tenon, with glue and stainless steel screws or nails, properly fitted and tightened. Suitable holdfasts made of mild steel flat (not less than 35 mm × 6 mm) shall be fixed on the sides of the frame and embedded into the wall with concrete. The frame shall have proper rebates for shutters and shall include cost of all grooves for hinges, tower bolts, stoppers, and other fittings. It shall also include provision for fixing of lock plate and other hardware cutting without any extra cost.The rate shall include the cost of teak wood, labour, cutting, jointing, holdfasts, screwing, adhesives, polishing, tools, transportation, scaffolding, and all incidental works required for proper installation. Measurement shall be taken in running meters along the outer length of the installed frame. |
| 18 | Providing and fixing factory-made PVC laminated door shutter, 30 mm thick, made of engineered core panel construction, manufactured as per IS: 4020. The shutter shall consist of a rigid framework with stiles and rails of treated engineered wood, bonded with waterproof synthetic resin adhesive conforming to IS: 848. The infill core shall be solid composite block board as per IS: 1659. The shutter faces shall be factory-laminated with 1.0 mm ± 0.1 mm thick PVC foil/laminate sheet, thermo-compressed and bonded uniformly on both sides using hot‐melt adhesive technology. The laminate finish shall be smooth, waterproof, termite and borer resistant, and shall include decorative wood-grain/plain texture. All exposed edges, cut-outs and joint edges shall be sealed with matching PVC edge beading and welded/sealed using heat-press or solvent-bonding to ensure moisture proofing.Shutter shall be supplied with provision for locking arrangement, hinges, and hardware fixing, including required solid backing/packing inside stiles and lock rail, ensuring adequate screw holding strength. The complete shutter shall meet physical strength/performance criteria mentioned in IS: 4020 for impact, deflection, squareness, water resistance and adhesion tests.Rate shall include: complete factory-manufactured door shutter with PVC laminate, inner core construction, sealing of edges, provision for hardware, delivery at site and installation including adhesive, nails/screws, etc.Note: Door frame and architectural hardware (hinges, tower bolt, lock, handles, door stopper, etc.) shall be paid separately under respective item |
| 19 | Providing and fixing 1.0 mm thick decorative laminate of approved make and shade, conforming to IS: 2046, on door shutters, partitions, cupboards, paneling or any other wood/board surface. The laminate shall be fixed using premium grade synthetic resin adhesive (Fevicol SH / SR type as applicable), confirming to IS: 851 or IS: 848, including proper surface preparation, edge finishing and complete workmanship.The laminate shall be machine pressed evenly to avoid air pockets and undulations, and all exposed edges shall be finished smooth and aligned to adjoining surfaces. Sharp corners shall be rounded as required to avoid peeling. The rate shall include cutting, edging, finishing of cutouts for handles/locks, provision of wooden lipping where required cleaning of adhesive residue, and final polishing/waxing where required.The laminate shall be free from waviness, bubbles, ripples, cracks and manufacturing defects and shall be provided only after approval of design, texture and shade by the Engineer-in-Charge.Rate shall include: Laminate sheet, adhesive, complete fixing, finishing at edges and cutouts, cleaning and final finishing.Note: Base surface such as plywood/MDF/block board/door shutter, and lipping/edge banding shall be paid separately under respective tender items. |
| 20 | Providing material and labour for fixing hydraulic rack and pinion door closer with standard arm (Silver finish) with screws to pivoted/ hinged door of approved make for specified door width with minimum 100kg capacity and one year guarantee. All adjustment screws face fixed. Rate shall be inclusive of fixing with using the template as per manufacturer’s specification & maintain in good working condition until defect liability period. The door closer shall conform to EN 1154 standard.a) with standard/ hold open arm with two independent closing valves and latching speed adjustable by arm without mounting back plate, Closing force complying with EN 1154 2 - 4 for up to 900 mm door shutter width |
| 21 | Providing material and labour for fixing SS 316 grade butt hinge of average 100 x 75 x 3 mm - with ball bearing of approved make as per approved sample with necessary screws etc. complete for all floor all height all level as directed by Engineer in Charge. |
| 22 | Providing material and labour for fixing set of dead lock of approved make with 50mm backseat, 20mm square for end with 72 mm centers including strike plate in satin stainless steel finish as per DIN 18251-1, grade 2 and prepared for euro profile cylinder (EPC) including strike plate and EPC length 60/70 mm standard Euro profile Pin Cylinder/ Half pin cylinder with both side key/ one side key one side knob operation with one pair of SS 316 grade Escutcheons (key hole plate) for wooden/ aluminium/ metal doors with necessary SS Phillips head screws etc complete for all floor, all level, all height as per approved sample and as directed by engineer in charge. The lock shall be with 3 keys. |
| 23 | Providing and Fixing SS 304 Grade Satin Finish 1.8 mm Thickness Aldrops of 16 mm dia x 250 mm including 3 nos. fixing Bracket and 1 no. locking bracket of approved make with necessary MS nickle Plating Bolts etc. complete for all floor, all height, all level as per approved sample and as directed by engineer in charge. |
| 24 | Providing material and labour for fixing SS 304 brush finish solid Door Stopper with magnet, fixed type, wall mounted (square/ round) of approved make with necessary screws etc. complete for all floor, all height, all level as per approved sample and as directed by engineer in charge. |
| 25 | Providing material and labour for fixing SS 304 grade brush finish solid Door bufer with pvc base, wall mounted (square/ round) of approved make with necessary screws etc. complete as approved by Engineer-in-charge in Charge. Please Enable Macros to View BoQ information |
| 26 | Providing material and labour for fixing SS 304 grade brush finish solid Door bufer with pvc base, wall mounted (square/ round) of approved make with necessary screws etc. complete as approved by Engineer-in-charge in Charge. Please Enable Macros to View BoQ information |
