Tender For Construction Of Prekshagrih/ Auditorium At Kakor District-Auraiya (U.P.) (Notice No. -39/Uppcl/Gm-7/E-Tender/2025-26 Dated: 08.05.2026), Auraiya-Uttar Pradesh

TDR : 55519082

Tender Notice
BOQ

6 Days Left

Auraiya , Uttar Pradesh

Tender Brief : Tender For Construction Of Prekshagrih/ Auditorium At Kakor District-Auraiya (U.P.) (Notice No. -39/Uppcl/Gm-7/E-Tender/2025-26 Dated: 08.05.2026)

Document Fees
₹ 17700 /-

EMD
₹ 2162000.0 /-

Tender Value
₹ 10.81 Crore /-

Submission Date
23-05-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Construction of Prekshagrih/ Auditorium at Kakor District-Auraiya (U.P.)
2	MULTIPURPOSE HALLEarth work in Excavation in trenches for foundations pipes cable etc in ordinary soil (Loam, clay or sand) including lift up to 1.50M and lead upto 50M and dressing of sides and ramming of bottom and disposal of surplus excavated earth as directed by the Engineer i.c. within a lead of 30 m.
3	Earth Filling By Avilable Earth
4	Earth work in filling under floor upto plinth including watering ramming by Cartage Earth
5	Sand Filling Under Floor
6	Providig and laying cement concrete 1:4:8 (1cement:4 C.sand: 8 Stone Ballast 40mm. nominal size) including supply of all materials, labour and T&P etc. required for proper completion of the work and curing complete also including cost of form work in foundation and floors.
7	R.C.C. works with cement approved coarse sand and 2 cm. (3/4\\") gauge approved stone ballast in the proportion 1:1.5:3 (1cement:1.5csand:3stone grit) excluding supply of reinforcement and its bending& binding. With 24BWG binding wire including supply of all Material,labours, tools and plants etc required for proper completion of the works. Strength of the concrete shall not be less than M-200 (a) in Foundation
8	(b) In Column
9	(c) in Lintel G.F.
10	(d) in Beam
11	(e) in Slab
12	Providing and injecting chemical emulsoin for preconstructional antitermite treatment and crsating a chemical barrier under and around the column pits wall trenches basement excavation top surface if plinth filling junction of wall and floor, along the external perimeter of binding expansion joints, surrounding of pipes and conduit etc, complete (Plinth area of the building at ground floor only shall be measured as per I.S. 6313 (Part II 1981)) Aldrine emusifiable concentrate or any other approved material such as Hepthachlor or chloradane will be used. The rate of application will be used. The rate of application of chemical emulsion shal be as follows:- (1) Treatment for masonary & foundation 5 Liters per SQM. (2). Back fill in intermediate contact with foundation 7.5 Litres per Sq.M. (3) Treatment of top surface of plinth filling 5 Litres per Sq.M. (4) Treatment of soil along external perimeter of Building 7.50 Litres per Sq.M. (5) Treatment of soil under apron along external perimeter 5 Litres per Sq.M.
13	Class- 150 brick work in 1:6 cement and C.sand mortar in Foundation including supply of all materials, labour and T & P etc. required for proper completion of work.
14	25mm. Thick D.P.C. 1:1.5:3 cement: c.sand: 13mm. Stone gritt including water Proofing Materials including Supply of all Material, Labour, T.&P. complete of work
15	Class- 150 brick work in 1:6 cement and C.sand mortar in Super Structure including supply of all materials, labour and T & P etc. required for proper completion of work. G.F.
16	Class- 150 brick work in 1:4 cement and C.sand mortar in Super Structure including supply of all materials, labour and T & P etc. required for proper completion of work.
17	12mm wall plaster 1:6 cement :coarse sand including cost of material labour T&P etc (a) inside
18	(b) outer
19	Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.
20	Providing & Laying Polished Vitrified tiles in Dado different sizes (thickness to be specified by the manufacturer) with water absorption's less than n 0.08% and conforming IS 15622 of approved make in all Colours and shades, laid on 20mm. Thick 1:4 (1cement : 4 Coarse sand) Including grouting the joints with white cement and matching pigment etc. Complete.Size 600*600 mm.
21	Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacturer), of approved make,in all colours, shades except burgundy, bottle green, black of any size asapproved by Engineer-in-Charge, in skirting, risers of steps and dados,over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) andjointing with grey cement slurry @ 3.3kg per sqm, including pointingin white cement mixed with pigment of matching shade complete.
22	Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conforming IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4Coarse sand), including pointing the joints with white cement and matching pigment etc, complete.
23	Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment,\ epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shade Area of slab over 0.50 sqm
24	Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer
25	Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work
26	Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.
27	Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.
28	Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:a) Applying a slurry coat of neat cement using 2.75 kg/sum. of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300mm height including cleaning the surface before treatment.
29	Making Khurra 4545 cm with everage minimum thickness of 5 cm cement concrete 1:2;4 (1 cement: 2coarse sand: 4 aggrgate 20mm. Nominal size over P.V.c. sheet 11*400Micron
30	Providing & Applying Two Coat White Cement Based Wall care Putty For Given Smooth surface for Painting complete of work.
31	Finishing walls with 2 Coat Weather coat exterior paint with Silicone additives of required shade
32	Painting wall with oil bound Distemper of approved brand and manufacture to give an even shade New work (two or more coats) over and including priming coat with cement primer.
33	Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.
34	40mm. Thick Apren Flooring 1:2:4 Cement:C.sand:20 mm. Stone grit with Floting coat of neat cement including supply of all Materials Labour and T & P etc. Complete of Work
35	S.S Stair Case Railing
36	Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes 110 mm diameter
37	Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. 110 mm Shoe
38	Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:
39	S/Fixing of 4mm thick glass pans
40	Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:35mm. thick (a) 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. D/L
41	(b) same as above but for S/L
42	Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S including cost of adhesive of approved quality.Providing and fixing of Lamination of door shutter.
43	Providing & Fixing of SS Door Bolt (a) 300x16 mm
44	(b) 250x16 mm
45	Providing & Fixing of SS Tower Bolt (a) 300x10 mm
46	(b) 150x10 mm
47	Providing & Fixing of SS Handles 125 mm
48	Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. Twin rubber stopper
49	Construction of Apren Drain 250x300mm. Internal Section Making with Brick work 1:4 cement c.sand Mortor Plasterd with 1:3 cement c.sand mortor with floting coat of neat cement.including all Material, Labour T.& P. complete of work
50	Providing and fixing PVC door frame as per specification.
51	30mm thick PVC door shutter as per specification
52	Centering and shuttering including strtting, propping etc. and removel (a) Foundations, footings etc
53	(b) Columns, pillars, Abutments, posts and struts
54	(c) Suspended Floor roofs, Landings, balconies and acces plateform with water proof ply 12mm.
55	(d) Lintels, beams, plinth beams with water proof ply 12mm
56	Providing and fixing water closet squatting pan ( european type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :
57	Providing and fixing white vitreous china pedestal type water closet(European type W.C. pan) with seat and lid, 10 litre low level whiteP.V.C. flushing cistern, including flush pipe, with manually controlleddevice (handle lever), conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls andfloors wherever required :
58	Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Flat back wash basin size 630*450 mm with single 15 mm C.P. brass pillar tap.
59	Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
60	Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm,including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink without drain board 610x510 mm bowl depth 200 mm
61	Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern,with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS :2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the wallsand floors wherever required : Range of four half stall urinals with 10 litre P.V.C.\ automatic flushing cistern
62	Providing and fixing P.V. C. Pipe 6kg.Pis including all Material, Labour T.&P. Complete of work. 110 mm dia.
63	Providing and fixing P.V. C. Clamp including all Material, Labour T.&P. Complete of work. For 110 mm dia.
64	Providing and fixing P.V. C. Bend including all Material, Labour T.&P. Complete of work. For 110 mm dia.
65	Providing and fixing P.V. C. N Trape including all Material, Labour T.&P. Complete of work. 90*90mm.
66	Providing and fixing P.V. C. D. Bend including all Material, Labour T.&P. Complete of work. For 110 mm dia.
67	Providing and fixing of P.V.C. Copler For 110 mm dia.
68	Providing and fixing of P.V.C. Covel 110mm. Ddia
69	Providing and fixing of P.V.C. D. Tee For 110 mm dia.
70	Providing and fixing of P.V.C. Tee For 110 mm dia.
71	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge (a) 20 mm dia. nominal bore
72	(b) 25 mm dia. nominal bore
73	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore
74	Providing and fixing uplasticised PVC connection pipe with brass unions : (a) 30 cm length 15 mm nominal bore
75	Providing and Fixing of G.I. Pipe in external work 25mm. dia
76	Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) 25 mm nominal bore
77	Cutting holes upto 30x30 cm in walls including making good the same : With F.P.S. bricks.
78	Cutting holes upto 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including finishing complete so as to make it leak proof.
79	Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore.
80	Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. as Such Hindwair 15 mm nominal bore
81	Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. as Such Hindwair 15 mm nominal bore.
82	Providing and fixing C.P. brass Short body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. as Such Hindwair 15 mm nominal bore
83	Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 as Such Hindwair 15 mm nominal bore
84	Providing and fixing of C.P. towel rod 24\\"heavy.
85	Providing & Placing of polyethylene waterstorage tank, ISI 12701 locking arregment and making necessary holes for inlet, outlet and overflowpipes but without fittings.
86	Providing & Making of Platefom for 1000 Ltr. P.V.C. Water Storege Tank.
87	GUEST HOUSEEarth work in Excavation in trenches for foundations pipes cable etc in ordinary soil (Loam, clay or sand) including lift up to 1.50M and lead upto 50M and dressing of sides and ramming of bottom and disposal of surplus excavated earth as directed by the Engineer i.c. within a lead of 30 m.
88	Earth Filling By Avilable Earth
89	Earth work in filling under floor upto plinth including watering ramming by Cartage Earth
90	Sand Filling Under Floor
91	Providig and laying cement concrete 1:4:8 (1cement:4 C.sand: 8 Stone Ballast 40mm. nominal size) including supply of all materials, labour and T&P etc. required for proper completion of the work and curing complete also including cost of form work in foundation and floors.
92	R.C.C. works with cement approved coarse sand and 2 cm. (3/4\\") gauge approved stone ballast in the proportion 1:1.5:3 (1cement:1.5csand:3stone grit) excluding supply of reinforcement and its bending& binding. With 24BWG binding wire including supply of all Material,labours, tools and plants etc required for proper completion of the works. Strength of the concrete shall not be less than M-200 in Foundation
93	(a) In Column G.F.
94	(b) F.F.
95	(c) 2nd Floor
96	(d) in Lintel G.F.
97	(e) F.F.
98	(f) 2nd Floor
99	(g) in Beam
100	(h) F.F.
101	(i) 2nd Floor
102	(j) in Slab
103	(k) F.F.
104	(l) 2nd Floor
105	Providing and injecting chemical emulsoin for preconstructional antitermite treatment and crsating a chemical barrier under and around the column pits wall trenches basement excavation top surface if plinth filling junction of wall and floor, along the external perimeter of binding expansion joints, surrounding of pipes and conduit etc, complete (Plinth area of the building at ground floor only shall be measured as per I.S. 6313 (Part II 1981)) Aldrine emusifiable concentrate or any other approved material such as Hepthachlor or chloradane will be used. The rate of application will be used. The rate of application of chemical emulsion shal be as follows:- (1) Treatment for masonary & foundation 5 Liters per SQM. (2). Back fill in intermediate contact with foundation 7.5 Litres per Sq.M. (3) Treatment of top surface of plinth filling 5 Litres per Sq.M. (4) Treatment of soil along external perimeter of Building 7.50 Litres per Sq.M. (5) Treatment of soil under apron along external perimeter 5 Litres per Sq.M.
106	Class- 150 brick work in 1:6 cement and C.sand mortar in Foundation including supply of all materials, labour and T & P etc. required for proper completion of work.
107	25mm. Thick D.P.C. 1:1.5:3 cement: c.sand: 13mm. Stone gritt including water Proofing Materials including Supply of all Material, Labour, T.&P. complete of work
108	Class- 150 brick work in 1:6 cement and C.sand mortar in Super Structure including supply of all materials, labour and T & P etc. required for proper completion of work. (a) G.F.
109	(b) F.F.
110	(c) 2nd Floor
111	Class- 150 brick work in 1:4 cement and C.sand mortar in Super Structure including supply of all materials, labour and T & P etc. required for proper completion of work. PARAPET
112	12mm wall plaster 1:6 cement :coarse sand including cost of material labour T&P etc Inside
113	12mm wall plaster 1:6 cement :coarse sand including cost of material labour T&P etc outer
114	Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.
115	Providing & Laying Polished Vitrified tiles in Dado different sizes (thickness to be specified by the manufacturer) with water absorption's less than n 0.08% and conforming IS 15622 of approved make in all Colours and shades, laid on 20mm. Thick 1:4 (1cement : 4 Coarse sand) Including grouting the joints with white cement and matching pigment etc. Complete.Size 600*600 mm.
116	Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size asapproved by Engineer-in-Charge, in skirting, risers of steps and dados,over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) andjointing with grey cement slurry @ 3.3kg per sqm, including pointingin white cement mixed with pigment of matching shade complete.
117	Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conforming IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4Coarse sand), including pointing the joints with white cement and matchingpigment etc, complete.
118	Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment,\ epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade Area of slab over 0.50 sqm
119	Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer
120	Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work
121	Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.
122	Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:a) Applying a slurry coat of neat cement using 2.75 kg/sum. of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300mm height including cleaning the surface before treatment.
123	Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen
124	Making Khurra 4545 cm with everage minimum thickness of 5 cm cement concrete 1:2;4 (1 cement: 2coarse sand: 4 aggrgate 20mm. Nominal size over P.V.c. sheet 11*400Micron
125	Providing & Applying Two Coat White Cement Based Wall care Putty For Given Smooth surface for Painting complete of work.
126	Finishing walls with 2 Coat Weather coat exterior paint with Silicone additives of required shade
127	Painting wall with oil bound Distemper of approved brand and manufacture to give an even shade New work (two or more coats) over and including priming coat with cement primer.
128	Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.
129	40mm. Thick Apren Flooring 1:2:4 Cement:C.sand:20 mm. Stone grit with Floting coat of neat cement including supply of all Materials Labour and T & P etc. Complete of Work
130	S.S Stair Case Railing
131	Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes 110 mm diameter
132	Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. 110 mm Shoe
133	Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:
134	20mm.thick 1:3 Cement: C.sand Mortor Bearing Plaster with Floting Coat of Neat Cement
135	S/Fixing of 4mm thick glass pans
136	Filling of Cinder in Sunken portion of Toilet including Supply of all Material, Labour, T.&P. complete of work.
137	Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:35mm. thick30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. S/L
138	Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S including cost of adhesive of approved quality.Providing and fixing of Lamination of door shutter.
139	Providing & Fixing of S.S. Door Bolt (a) 300x16 mm
140	(b) 250x16 mm
141	Providing & Fixing of S.S. Tower Bolt 300x10 mm
142	Providing & Fixing of S.S. Handles 125 mm
143	Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. Twin rubber stopper
144	Construction of Apren Drain 250x300mm. Internal Section Making with Brick work 1:4 cement c.sand Mortor Plasterd with 1:3 cement c.sand mortor with floting coat of neat cement.including all Material, Labour T.& P. complete of work
145	Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws 30 mm thick shutters With ISI marked stainless steel butt hinges of required size Second class teak wood
146	Providing & Fixing PVC door frames as per specification
147	30mm thick PVC door shutter as per specification
148	Centering and shuttering including strtting, propping etc. and removel (a) Foundations, footings etc
149	(b) Columns, pillars, Abutments, posts and struts
150	(c) Suspended Floor roofs, Landings, balconies and acces plateform with water proof ply 12mm.
151	(d) Lintels, beams, plinth beams with water proof ply 12mm
152	Providing and fixing water closet squatting pan ( european type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :
153	Providing and fixing white vitreous china pedestal type water closet(European type W.C. pan) with seat and lid, 10 litre low level whiteP.V.C. flushing cistern, including flush pipe, with manually controlleddevice (handle lever), conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls andfloors wherever required :
154	Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Flat back wash basin size 630*450 mm with single 15 mm C.P. brass pillar tap.
155	Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
156	Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink without drain board 610x510 mm bowl depth 200 mm
157	Providing and fixing P.V. C. Pipe 6kg.Pis including all Material, Labour T.&P. Complete of work. 110 mm dia.
158	Providing and fixing P.V. C. Clamp including all Material, Labour T.&P. Complete of work. For 110 mm dia.
159	Providing and fixing P.V. C. Bend including all Material, Labour T.&P. Complete of work. For 110 mm dia.
160	Providing and fixing P.V. C. N Trape including all Material, Labour T.&P. Complete of work. 90*90mm.
161	Providing and fixing P.V. C. D. Bend including all Material, Labour T.&P. Complete of work. For 110 mm dia.
162	Providing and fixing of P.V.C. Copler For 110 mm dia.
163	Providing and fixing of P.V.C. Covel 110mm. Ddia
164	Providing and fixing of P.V.C. D. Tee For 110 mm dia.
165	Providing and fixing of P.V.C. Tee For 110 mm dia.
166	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge (a) 20 mm dia. nominal bore
167	(b) 25 mm dia. nominal bore
168	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : (a) 25 mm nominal bore
169	Providing and fixing uplasticised PVC connection pipe with brass unions : 30 cm length 15 mm nominal bore
170	Providing and Fixing of G.I. Pipe in external work 25mm. dia
171	Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) 25 mm nominal bore
172	Cutting holes upto 30x30 cm in walls including making good the same : With F.P.S. bricks.
173	Cutting holes upto 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including finishing complete so as to make it leak proof.
174	Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore.
175	Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. as Such Hindwair 15 mm nominal bore
176	Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. as Such Hindwair 15 mm nominal bore.
177	Providing and fixing C.P. brass Short body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. as Such Hindwair 15 mm nominal bore
178	Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 as Such Hindwair 15 mm nominal bore
179	Providing and fixing of C.P. towel rod 24\\"heavy.
180	Providing & Placing of polyethylene waterstorage tank, ISI 12701 locking arregment and making necessary holes for inlet, outlet and overflowpipes but without fittings.
181	Providing & Making of Platefom for 1000 Ltr. P.V.C. Water Storege Tank.
182	FOOD COURT & KIOKSEarth work in Excavation in trenches for foundations pipes cable etc in ordinary soil (Loam, clay or sand) including lift up to 1.50M and lead upto 50M and dressing of sides and ramming of bottom and disposal of surplus excavated earth as directed by the Engineer i.c. within a lead of 30 m.
183	Earth Filling By Avilable Earth
184	Sand Filling Under Floor
185	Providig and laying cement concrete 1:4:8 (1cement:4 C.sand: 8 Stone Ballast 40mm. nominal size) including supply of all materials, labour and T&P etc. required for proper completion of the work and curing complete also including cost of form work in foundation and floors.
186	R.C.C. works with cement approved coarse sand and 2 cm. (3/4\\") gauge approved stone ballast in the proportion 1:1.5:3 (1cement:1.5csand:3stone grit) excluding supply of reinforcement and its bending& binding. With 24BWG binding wire including supply of all Material,labours, tools and plants etc required for proper completion of the works. Strength of the concrete shall not be less than M-200 in Foundation (a) plinth band
187	(b) lintel band
188	(c) in Slab
189	Providing and injecting chemical emulsoin for preconstructional antitermite treatment and crsating a chemical barrier under and around the column pits wall trenches basement excavation top surface if plinth filling junction of wall and floor, along the external perimeter of binding expansion joints, surrounding of pipes and conduit etc, complete (Plinth area of the building at ground floor only shall be measured as per I.S. 6313 (Part II 1981)) Aldrine emusifiable concentrate or any other approved material such as Hepthachlor or chloradane will be used. The rate of application will be used. The rate of application of chemical emulsion shal be as follows:- (1) Treatment for masonary & foundation 5 Liters per SQM. (2). Back fill in intermediate contact with foundation 7.5 Litres per Sq.M. (3) Treatment of top surface of plinth filling 5 Litres per Sq.M. (4) Treatment of soil along external perimeter of Building 7.50 Litres per Sq.M. (5) Treatment of soil under apron along external perimeter 5 Litres per Sq.M.
190	Class- 150 brick work in 1:6 cement and C.sand mortar in Foundation including supply of all materials, labour and T & P etc. required for proper completion of work.
191	25mm. Thick D.P.C. 1:1.5:3 cement: c.sand: 13mm. Stone gritt including water Proofing Materials including Supply of all Material, Labour, T.&P. complete of work
192	Class- 150 brick work in 1:6 cement and C.sand mortar in Super Structure including supply of all materials, labour and T & P etc. required for proper completion of work. G.F.
193	Class- 150 brick work in 1:4 cement and C.sand mortar in Super Structure including supply of all materials, labour and T & P etc. required for proper completion of work.
194	12mm wall plaster 1:6 cement :coarse sand including cost of material labour T&P etc
195	Providing & Laying Polished Vitrified tiles in Dado different sizes (thickness to be specified by the manufacturer) with water absorption's less than n 0.08% and conforming IS 15622 of approved make in all Colours and shades, laid on 20mm. Thick 1:4 (1cement : 4 Coarse sand) Including grouting the joints with white cement and matching pigment etc. Complete.Size 600*600 mm.
196	Supply and fixing of rolling shutter etc complite of work.
197	Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:a) Applying a slurry coat of neat cement using 2.75 kg/sum. of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300mm height including cleaning the surface before treatment.
198	Making Khurra 4545 cm with everage minimum thickness of 5 cm cement concrete 1:2;4 (1 cement: 2coarse sand: 4 aggrgate 20mm. Nominal size over P.V.c. sheet 11*400Micron
199	Providing & Applying Two Coat White Cement Based Wall care Putty For Given Smooth surface for Painting complete of work.
200	Finishing walls with 2 Coat Weather coat exterior paint with Silicone additives of required shade
201	Painting wall with oil bound Distemper of approved brand and manufacture to give an even shade New work (two or more coats) over and including priming coat with cement primer.
202	Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.
203	Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes 110 mm diameter
204	Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. 110 mm Shoe
205	Centering and shuttering including strtting, propping etc. and removel Lintels, beams, plinth beams with water proof pply 12mm
206	BOUNDARY WALLEarth work in Excavation in trenches for foundations pipes cable etc in ordinary soil (Loam, clay or sand) including lift up to 1.50M and lead upto 50M and dressing of sides and ramming of bottom and disposal of surplus excavated earth as directed by the Engineer i.c. within a lead of 30 m.
207	Earth Filling By Avilable Earth
208	Providig and laying cement concrete 1:4:8 (1cement:4 C.sand: 8 Stone Ballast 40mm. nominal size) including supply of all materials, labour and T&P etc. required for proper completion of the work and curing complete also including cost of form work in foundation and floors.
209	R.C.C. works with cement approved coarse sand and 2 cm. (3/4\\") gauge approved stone ballast in the proportion 1:1.5:3 (1cement:1.5csand:3stone grit) excluding supply of reinforcement and its bending& binding. With 24BWG binding wire including supply of all Material,labours, tools and plants etc required for proper completion of the works. Strength of the concrete shall not be less than M-200 (a) in Foundation
210	(b) In Column G.F.
211	(c) in Lintel G.F.
212	25mm. Thick D.P.C. 1:1.5:3 cement: c.sand: 13mm. Stone gritt including water Proofing Materials including Supply of all Material, Labour, T.&P. complete of work
213	Class- 150 brick work in 1:4 cement and C.sand mortar in Super Structure including supply of all materials, labour and T & P etc. required for proper completion of work.
214	12mm wall plaster 1:6 cement :coarse sand including cost of material labour T&P etc outer
215	Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.
216	Finishing walls with 2 Coat Weather coat exterior paint with Silicone additives of required shade
217	Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.
218	Centering and shuttering including strtting, propping etc. and removel (a) Foundations, footings etc
219	(b) Columns, pillars, Abutments, posts and struts
220	(c) Lintels, beams, plinth beams with water proof ply 12mm
221	M.S. Gate (2 Nos.)Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.
222	Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture.
223	PUMP ROOMEarth work in Excavation in trenches for foundations pipes cable etc in ordinary soil (Loam, clay or sand) including lift up to 1.50M and lead upto 50M and dressing of sides and ramming of bottom and disposal of surplus excavated earth as directed by the Engineer i.c. within a lead of 30 m.
224	Earth Filling By Avilable Earth
225	Earth work in filling under floor upto plinth including watering ramming by Cartage Earth
226	Sand Filling Under Floor
227	Providig and laying cement concrete 1:4:8 (1cement:4 C.sand: 8 Stone Ballast 40mm. nominal size) including supply of all materials, labour and T&P etc. required for proper completion of the work and curing complete also including cost of form work in foundation and floors.
228	R.C.C. works with cement approved coarse sand and 2 cm. (3/4\\") gauge approved stone ballast in the proportion 1:1.5:3 (1cement:1.5csand:3stone grit) excluding supply of reinforcement and its bending& binding. With 24BWG binding wire including supply of all Material,labours, tools and plants etc required for proper completion of the works. Strength of the concrete shall not be less than M-200 (a) in Foundation
229	(b) in Lintel.
230	(c) in Slab
231	Class- 150 brick work in 1:6 cement and C.sand mortar in Foundation including supply of all materials, labour and T & P etc. required for proper completion of work.
232	25mm. Thick D.P.C. 1:1.5:3 cement: c.sand: 13mm. Stone gritt including water Proofing Materials including Supply of all Material, Labour, T.&P. complete of work
233	Class- 150 brick work in 1:6 cement and C.sand mortar in Super Structure including supply of all materials, labour and T & P etc. required for proper completion of work. G.F.
234	Class- 150 brick work in 1:4 cement and C.sand mortar in Super Structure including supply of all materials, labour and T & P etc. required for proper completion of work.
235	12mm wall plaster 1:6 cement :coarse sand including cost of material labour T&P etc
236	Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.
237	Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.
238	Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:a) Applying a slurry coat of neat cement using 2.75 kg/sum. of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300mm height including cleaning the surface before treatment.
239	Making Khurra 4545 cm with everage minimum thickness of 5 cm cement concrete 1:2;4 (1 cement: 2coarse sand: 4 aggrgate 20mm. Nominal size over P.V.c. sheet 11*400Micron
240	Finishing walls with 2 Coat Weather coat exterior paint with Silicone additives of required shade
241	Painting wall with oil bound Distemper of approved brand and manufacture to give an even shade New work (two or more coats) over and including priming coat with cement primer.
242	Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.
243	40mm. Thick Apren Flooring 1:2:4 Cement:C.sand:20 mm. Stone grit with Floting coat of neat cement including supply of all Materials Labour and T & P etc. Complete of Work
244	Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes 110 mm diameter
245	Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. 110 mm Shoe
246	Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:
247	Centering and shuttering including strtting, propping etc. and removel Lintels, beams, plinth beams with water proof ply 12mm
248	GAURD ROOMEarth work in Excavation in trenches for foundations pipes cable etc in ordinary soil (Loam, clay or sand) including lift up to 1.50M and lead upto 50M and dressing of sides and ramming of bottom and disposal of surplus excavated earth as directed by the Engineer i.c. within a lead of 30 m.
249	Earth Filling By Avilable Earth
250	Earth work in filling under floor upto plinth including watering ramming by Cartage Earth
251	Sand Filling Under Floor
252	Providig and laying cement concrete 1:4:8 (1cement:4 C.sand: 8 Stone Ballast 40mm. nominal size) including supply of all materials, labour and T&P etc. required for proper completion of the work and curing complete also including cost of form work in foundation and floors.
253	R.C.C. works with cement approved coarse sand and 2 cm. (3/4\\") gauge approved stone ballast in the proportion 1:1.5:3 (1cement:1.5csand:3stone grit) excluding supply of reinforcement and its bending& binding. With 24BWG binding wire including supply of all Material,labours, tools and plants etc required for proper completion of the works. Strength of the concrete shall not be less than M-200 (a) in Foundation
254	(b) in Lintel.
255	(c) in Slab
256	Class- 150 brick work in 1:6 cement and C.sand mortar in Foundation including supply of all materials, labour and T & P etc. required for proper completion of work.
257	25mm. Thick D.P.C. 1:1.5:3 cement: c.sand: 13mm. Stone gritt including water Proofing Materials including Supply of all Material, Labour, T.&P. complete of work
258	Class- 150 brick work in 1:6 cement and C.sand mortar in Super Structure including supply of all materials, labour and T & P etc. required for proper completion of work. G.F.
259	Class- 150 brick work in 1:4 cement and C.sand mortar in Super Structure including supply of all materials, labour and T & P etc. required for proper completion of work.
260	12mm wall plaster 1:6 cement :coarse sand including cost of material labour T&P etc
261	Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.
262	Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.
263	Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:a) Applying a slurry coat of neat cement using 2.75 kg/sum. of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300mm height including cleaning the surface before treatment.
264	Making Khurra 4545 cm with everage minimum thickness of 5 cm cement concrete 1:2;4 (1 cement: 2coarse sand: 4 aggrgate 20mm. Nominal size over P.V.c. sheet 11*400Micron
265	Finishing walls with 2 Coat Weather coat exterior paint with Silicone additives of required shade
266	Painting wall with oil bound Distemper of approved brand and manufacture to give an even shade New work (two or more coats) over and including priming coat with cement primer.
267	Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.
268	40mm. Thick Apren Flooring 1:2:4 Cement:C.sand:20 mm. Stone grit with Floting coat of neat cement including supply of all Materials Labour and T & P etc. Complete of Work
269	Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes 110 mm diameter
270	Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. 110 mm Shoe
271	Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:
272	Centering and shuttering including strtting, propping etc. and removel Lintels, beams, plinth beams with water proof pply 12mm
273	INTERLOCKINGEarth work in Excavation in trenches for foundations pipes cable etc in ordinary soil (Loam, clay or sand) including lift up to 1.50M and lead upto 50M and dressing of sides and ramming of bottom and disposal of surplus excavated earth as directed by the Engineer i.c. within a lead of 30 m.
274	Providig and laying cement concrete 1:4:8 (1cement:4 sand: 8 Stone Ballast 40mm. nominal size) including supply of all materials, labour and T&P etc. required for proper completion of the work and curing complete also including cost of form work in foundation and floors.
275	Class- 75 brick work in 1:4 cement and C.sand mortar in Super Structure including supply of all materials, labour and T & P etc. required for proper completion of work.
276	P.C.C. 1:2:4 cement;csand: stone gritt
277	Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge With material conforming to Grade-II (size range 53 mmto 0.075 mm ) having CBR Value-25
278	12mm wall plaster 1:6 cement :coarse sand including cost of material labour T&P etc
279	Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 80 mm thick C.C. paver block of M-30 grade with approvedcolor design and pattern.
280	BORINGBoring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level.300mm. dia
281	Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, above 90 metre depth below ground level.300mm. dia
282	Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200mm. dia
283	Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.200mm. dia
284	Gravel Packing in Tubewell Construction accordanse With IS 4097
285	Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.
286	Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessarybolts & nuts of required size complete.Supply & Laying
287	Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).Supply & Laying of 200mm. Dia M.S. bail plug
288	K.S.B. make submersible pump 5H.P.
289	Cantrol Pannel with 100 Amp. Main switch
290	Flat Copper Cable 1x3x6mm. ISI Mark
291	Supply of 80 mm. dia M.S. column pipe of c class both side flanged type complete
292	Supply of Steel wair robe of 1/2\\" size
293	RAIN WATER HARVESTINGEarth work in Excavation in trenches for foundations pipes cable etc in ordinary soil (Loam, clay or sand) including lift up to 1.50M and lead upto 50M and dressing of sides and ramming of bottom and disposal of surplus excavated earth as directed by the Engineer i.c. within a lead of 30 m. up tp 1.50mtr.
294	(a) 1.50 to 3.00 mtr.
295	(b) 3.00 to 4.65 mtr.
296	Providig and laying cement concrete 1:4:8 (1cement:4fine sand: 8 Stone Ballast 40mm. nominal size) including supply of all materials, labour and T&P etc. required for proper completion of the work and curing complete also including cost of form work in foundation and floors.
297	R.C.C. works with cement approved coarse sand and 20mm gauge approved stone grit in the proportion 1:2:4 (1cement:6aggregate) in lintels of doors and windows excluding supply of reinforcement and its bending& binding. but including its fixing and binding the same with 24 BWGGI binding wire and including necessary centering and shuttering etc. and also including supply of all materials, labours, tools and plants etc required for proper completion of the works. Binding wire cost being included in the item
298	Centring & Shutring Slab
299	Edges of Slab
300	Class- 150 brick work in 1:4 cement and C.sand mortar in Super Structure including supply of all materials, labour and T & P etc. required for proper completion of work.
301	15mm wall plaster 1:6 cement :coarse sand including cost of material labour T&P etc.
302	Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.
303	Providing M.S. foot rests including fixing in manholes with 20x20x10cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 gradedstone aggregate 20 mm nominal size) as per standard design :
304	Providing & Fixing of Posititon Precast RCC Manhole cover and frame of Required shape and approved quailty
305	Excavating trenches of required width for pipes, cables, etc includingexcavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returningthe soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. anddisposing of surplus excavated soil as directed, within a lead of 50 m :Pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm
306	Providing and laying non-pressure NP2 class (light duty) R.C.C. pipeswith collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe
307	Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement: 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2coarse sand : 4 graded stone aggregate 20 mm nominal size),foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thickwith cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement completeas per standard design : Size 600600450
308	Supplying and stacking at site.90 mm to 45 mm size stone aggregate
309	Stone screening 11.2 mm nominal size (Type B)
310	Red Bajri
311	Drilling of 300mm. Dia bore hole manually
312	Supply of 160mm dia rigid PVC pipe (4kg./sqcm pressure rating) and accessories
313	Supply of 160mm dia sloted rigid PVC pipe (4kg./sqcm pressure rating) and accessories
314	supply and fixing of nylon jali around the sloted pipes complet as required
315	Providing and packing of coarse sand around the pipe
316	transport of Boring tools other required equipments and instalation at site
317	Lowering of 160mm. Dia rigid P.V.C. pipe in bore hole including cutting jointing etc. complete
318	TOILET BLOCKEarth work in Excavation in trenches for foundations pipes cable etc in ordinary soil (Loam, clay or sand) including lift up to 1.50M and lead upto 50M and dressing of sides and ramming of bottom and disposal of surplus excavated earth as directed by the Engineer i.c. within a lead of 30 m.
319	Earth Filling By Avilable Earth
320	Sand Filling Under Floor
321	Providig and laying cement concrete 1:4:8 (1cement:4 C.sand: 8 Stone Ballast 40mm. nominal size) including supply of all materials, labour and T&P etc. required for proper completion of the work and curing complete also including cost of form work in foundation and floors.
322	R.C.C. works with cement approved coarse sand and 2 cm. (3/4\\") gauge approved stone ballast in the proportion 1:1.5:3 (1cement:1.5csand:3stone grit) excluding supply of reinforcement and its bending& binding. With 24BWG binding wire including supply of all Material,labours, tools and plants etc required for proper completion of the works. Strength of the concrete shall not be less than M-200 in Foundation (a) plinth band
323	(b) lintel band
324	(c) in Slab
325	Providing and injecting chemical emulsoin for preconstructional antitermite treatment and crsating a chemical barrier under and around the column pits wall trenches basement excavation top surface if plinth filling junction of wall and floor, along the external perimeter of binding expansion joints, surrounding of pipes and conduit etc, complete (Plinth area of the building at ground floor only shall be measured as per I.S. 6313 (Part II 1981)) Aldrine emusifiable concentrate or any other approved material such as Hepthachlor or chloradane will be used. The rate of application will be used. The rate of application of chemical emulsion shal be as follows:- (1) Treatment for masonary & foundation 5 Liters per SQM. (2). Back fill in intermediate contact with foundation 7.5 Litres per Sq.M. (3) Treatment of top surface of plinth filling 5 Litres per Sq.M. (4) Treatment of soil along external perimeter of Building 7.50 Litres per Sq.M. (5) Treatment of soil under apron along external perimeter 5 Litres per Sq.M.
326	Class- 150 brick work in 1:6 cement and C.sand mortar in Foundation including supply of all materials, labour and T & P etc. required for proper completion of work.
327	25mm. Thick D.P.C. 1:1.5:3 cement: c.sand: 13mm. Stone gritt including water Proofing Materials including Supply of all Material, Labour, T.&P. complete of work
328	Class- 150 brick work in 1:6 cement and C.sand mortar in Super Structure including supply of all materials, labour and T & P etc. required for proper completion of work. G.F.
329	Class- 150 brick work in 1:4 cement and C.sand mortar in Super Structure including supply of all materials, labour and T & P etc. required for proper completion of work.
330	12mm wall plaster 1:6 cement :coarse sand including cost of material labour T&P etc
331	Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size asapproved by Engineer-in-Charge, in skirting, risers of steps and dados,over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) andjointing with grey cement slurry @ 3.3kg per sqm, including pointingin white cement mixed with pigment of matching shade complete.
332	Providing and laying Ceramic glazed wall tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conforming IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4Coarse sand), including pointing the joints with white cement and matching pigment etc, complete.
333	Providing and fixing factory made pvc door frame as per specification.
334	Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:a) Applying a slurry coat of neat cement using 2.75 kg/sum. of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300mm height including cleaning the surface before treatment.
335	Making Khurra 4545 cm with everage minimum thickness of 5 cm cement concrete 1:2;4 (1 cement: 2coarse sand: 4 aggrgate 20mm. Nominal size over P.V.c. sheet 11*400Micron
336	Providing & Applying Two Coat White Cement Based Wall care Putty For Given Smooth surface for Painting complete of work.
337	Finishing walls with 2 Coat Weather coat exterior paint with Silicone additives of required shade
338	Painting wall with oil bound Distemper of approved brand and manufacture to give an even shade New work (two or more coats) over and including priming coat with cement primer.
339	Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.
340	Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes 110 mm diameter
341	Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. 110 mm Shoe
342	35mm thick factory made solid panel pvc door shutter
343	Providing & Fixing of S.S. Door Bolt 250x16 mm
344	Providing & Fixing of S.S. Tower Bolt 300x10 mm
345	Centering and shuttering including strtting, propping etc. and removel Lintels, beams, plinth beams with water proof pply 12mm
346	DRAINEarth work in exacavation in trenches for foundations land for pipes cables etc. in ordinary soil (loan clay or sand) including lift upto 1.5 m and dressing of sides and ramming of bottom sand disposal of surplus excavated earth as directed by the Engineer i/c with in a lead of 50m.
347	Providing and laying in cement concrete 1:2:4 (1 cement :4coarse sand :4 graded stone aggregate 40 mm nominal size) and curing complete, including cost of form-work, in foundation and floors. Same as above but 1:4:8
348	Class 150 Brick Work in 1:4 cement and coarse sand of 2.20 fineness modulus mortar in foundation and plinth including supply of all materials, labour and tools and plants etc. required for proper completion of the work.
349	Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.
350	20 mm cement plaster on single or half brick wall finished with a floating coat of neat cement of mix : 1:3(1 cement: 3 Coarse sand)
351	SEPTIK TANK & SOAK PITEarth work in Excavation in trenches for foundations pipes cable etc in ordinary soil (Loam, clay or sand) including lift up to 1.50M and lead upto 50M and dressing of sides and ramming of bottom and disposal of surplus excavated earth as directed by the Engineer i.c. within a lead of 30 m.
352	Earth Filling By Avilable Earth
353	Providig and laying cement concrete 1:4:8 (1cement:4 C.sand: 8 Stone Ballast 40mm. nominal size) including supply of all materials, labour and T&P etc. required for proper completion of the work and curing complete also including cost of form work in foundation and floors.
354	R.C.C. works with cement approved coarse sand and 2 cm. (3/4\\") gauge approved stone ballast in the proportion 1:1.5:3 (1cement:1.5csand:3stone grit) excluding supply of reinforcement and its bending& binding. With 24BWG binding wire including supply of all Material,labours, tools and plants etc required for proper completion of the works. Strength of the concrete shall not be less than M-200 in Foundation
355	Class- 150 brick work in 1:6 cement and C.sand mortar in Foundation including supply of all materials, labour and T & P etc. required for proper completion of work.
356	15mm wall plaster 1:3cement :coarse sand including cost of material labour T&P etc
357	Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.
358	50mm. Thick Flooring 1:2:4 Cement:C.sand:20 mm. Stone grit with Floting coat of neat cement including supply of all Materials Labour and T & P etc. Complete of Work
359	Brick bats filling in s p
360	Centering and shuttering including strtting, propping etc. and removel Lintels, beams, plinth beams with water proof pply 12mm
361	ELECTRIFICATION WORK MP HALLWiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C
362	Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.
363	Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
364	Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. (a) 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
365	(b) 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
366	(c) 2 X 6 sq. mm + 1 X 6 sq. mm earth wire
367	(d) 4 X 10 sq. mm + 2 X 6 sq. mm earth wire
368	Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 1 run of cable
369	Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm
370	Supplying and fixing following modular switch/ socket on theexisting modular plate & switch box including connections butexcluding modular plate etc. as required. (a) 5/6 A switch
371	(b) 3 pin 5/6 A socket outlet
372	(c) RJ45 socket cat 6 with shutter
373	Supplying and fixing two module stepped type electronic fanregulator on the existing modular plate switch box includingconnections but excluding modular plate etc. as required.
374	Supplying and fixing following size/ modules, GI box alongwithmodular base & cover plate for modular switches in recess etc.as required. 1 or 2 Module (75mmX75mm)
375	Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.
376	Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.
377	Installation of exhaust fan in the existing opening, includingmaking good the damage, connection, testing, commissioningetc. as required. Upto 450 mm sweep
378	Extra for fixing the louvers/ shutters complete with frame for aexhaust fan of all sizes.
379	Supplying & fixing suitable size GI box wih modular plate andcover in front on surface or in recess including providing andfixing 25 A modular socket outlet and 25 A modular SP MCB, \\"C\\" curve including connections, painting etc. as required.
380	Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 way , Double door
381	Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) (a) 4 way (4 + 12), Double door
382	(b) 6 way (4 + 18), Double door
383	Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. (a) Single pole
384	(b) Double pole
385	Triple pole and neutral
386	Supplying and fixing 40/63A rating, 415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of Four poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Similar to Legrand DX3 AC MCBs or equivalent.
387	Supplying and installing following size of perforated paintedwith powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness
388	Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thickincluding accessories, and providing masonry enclosure withcover plate having locking arrangement and watering pipe of2.7 metre long etc. with charcoal/ coke and salt as required.
389	Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I.pipe from earth electrode including connection with G.I. nut,bolt, spring, washer excavation and re-filling etc. as required.
390	Providing and fixing 25 mm X 5 mm G.I. strip on surface or inrecess for connections etc. as required.
391	Supply of 8W Green Perform Sleek is a high performance low-height LED downlighter suited for requirements of any modern professional workspace. Robust PDC housing ensures long system. Narrow rim renders a pleasing aesthetic look. similar to Philips DN295B LED8S-6500 PSU WH or equivalent.
392	Supply of 15W Green Perform Sleek is a high performance low-height LED downlighter suited for requirements of any modern professional workspace. Robust PDC housing ensures long system. Narrow rim renders a pleasing aesthetic look. similar to Philips DN295B LED8S-6500 PSU WH or equivalent.
393	Supply and fixing of LED Tube Light with batten suitable for up to 1 X 22 watt LED tube light fitting including tube on Surface complete in all respect. CAT- AAA
394	Supply and fixing of 36 Watt to 46 Watt indoor Recess mounting LED Square Fitting for Armstrong Ceiling having Powder coated die cast aluminium housing body with extended heat sink and diffuser of Special Polycarbonate meterial and driver set complete in all respect. CAT-AAA
395	SITC of 12W Extruded aluminium batten available in 2ft run length with multiple lumen packages and suitable for surface, wall & conduit ounting (with accessories). similar to Philips Type HSN Code MRP (INR) BN 021 LED12S 6500 PSU GR or equivalent.
396	Supply & Installation of Call Buzzer of approved Make
397	Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.
398	Supply of Pressure die cast housing LED bulkhead with IP66protection and IK09 impact resistance suitable for surface and wall mounting applications. Similar to Philips Cat Ref. WT202W LED6S NW PSU S2 PC or equivalent.
399	Supply & Installation of 450mm Sweep wall fan operating at 230V as per direction of Engineer in charge.
400	Supply & Installation of Totally enclosed exhaust fan, 300mm sweep continously rated highly efficient heavy-dutymotor similar to Crompton Cat. Ref. Trans Air 12\\" or equivalent.
401	Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. (a) 4 X 16 sq. mm (28mm)
402	(b) 3½ X 35 sq. mm (32mm)
403	(c) 3½ X 95 sq. mm (45mm)
404	Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 95 sq. mm and upto 185 sq. mm
405	Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 95 sq. mm and upto 185 sq. mm
406	Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. Upto 35 sq. mm
407	Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. 300 mm dia
408	3 Phase Input & 3 Phase Output 10KVA UPS Supply, installation, testing, and commissioning of UPS system with following features1. High freq. PWM inverter using IGBT2. Manual/Auto bypass switch3. SMF batteries to provide approx. 30 min backup time on IT load alongwith battery rack
409	Main LT PanelDesign, Manufacturing, Supply, Commissioning & Testing of Main LT Panel. The panel will be totally enclosed type with, free standing, floor mounted, indoor duty, dust & vermin proof, , front operated, electrical panel fabricated from 2 mm thick M.S. Sheet as per specifications & drawing laid in this document and will be complete with the main and auxiliary bus bars, multimeter, indication lamps, CT's, protection MCB, interconnection wiring, earth bus and will be powder coated finish with 50 micron thickness.The Main LT Panel shall use all draw out type breakers suitable for 415 V AC, 3 phase, 50 Hz, 3 phase 4 wire supply system. The panel shall have AMF facility to achieve electrical interlocking, synchronizing, buscoupler switching, auto operation of incommer and bus coupler, auto start of D.G. Sets, auto D.G. running by pre set timing, auto changeover etc and having following incomming and outgoing Air Circuit Breakers, FSU's as per the drawing and specification. Each incoming breaker will have microprocessor based releases and all outgoing breaker will have minimum electrostatic releases over 250A & thermal magnetic release below 250A. The Panel will be made as per detailed specifications & drawings forming part of this document. Fault level of panel shall be 35 MVA. INCOMMER100Amp. 16KA FP With S/C, U/V, E/F Protection MCCB-1 no.BUSBARS1 Nos. 160 Amp FP busbars of aluminium alloy as per SLD.OUTGOING32Amp. 10KA FP MCB 2 No.63Amp. 10KA FP MCCB 3 No.INSTRUMENTS1 sets of multifunction meter with parameter current,voltage, KWH, KVAH, Power factor on incoming from transformers with RS 485 port.1 Sets of phase indicating lights (RYB) with protection fuses (one set for each incoming breaker).1 Sets breaker 'ON' & 'OFF' indicating lamp (one set for each incoming breaker).1 Sets auto trip indicating lamp .
410	ELECTRIFICATION WORK GUEST HOUSEWiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C
411	Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C
412	Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
413	Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. (a) 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
414	(b) 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
415	(c) 2 X 6 sq. mm + 1 X 6 sq. mm earth wire
416	(d) 4 X 10 sq. mm + 2 X 6 sq. mm earth wire
417	(e) 4 X 16 sq. mm + 2 X 6 sq. mm earth wire
418	Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.
419	Supplying and fixing of following sizes of medium class PVCconduit along with accessories in surface/recess includingcutting the wall and making good the same in case of recessedconduit as required. 25 mm
420	Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. (a) 5/6 A switch
421	(b) 3 pin 5/6 A socket outlet
422	(c) TV socket outlet
423	Supplying and fixing two module stepped type electronic fanregulator on the existing modular plate switch box includingconnections but excluding modular plate etc. as required.
424	Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75mmX75mm)
425	Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.
426	Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.
427	Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep
428	Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.
429	Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, \\"C\\" curve including connections, painting etc. as required.
430	Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 way (4 + 18), Double door
431	Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole
432	Supplying and fixing 40/63A rating, 415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of Four poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Similar to Legrand DX3 AC MCBs or equivalent.
433	Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness
434	Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
435	Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.
436	Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.
437	Supply of 8W Green Perform Sleek is a high performance low-height LED downlighter suited for requirements of any modern professional workspace. Robust PDC housing ensures long system. Narrow rim renders a pleasing aesthetic look. similar to Philips DN295B LED8S-6500 PSU WH or equivalent.
438	Supply of 15W Green Perform Sleek is a high performance low-height LED downlighter suited for requirements of any modern professional workspace. Robust PDC housing ensures long system. Narrow rim renders a pleasing aesthetic look. similar to Philips DN295B LED8S-6500 PSU WH or equivalent.
439	SITC of 12W Extruded aluminium batten available in 2ft run length with multiple lumen packages and suitable for surface, wall & conduit ounting (with accessories). similar to Philips Type HSN Code MRP (INR) BN 021 LED12S 6500 PSU GR or equivalent.
440	Supply & Installation of Call Buzzer of approved Make
441	Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.
442	Supply of Pressure die cast housing LED bulkhead with IP66protection and IK09 impact resistance suitable for surface and wall mounting applications. Similar to Philips Cat Ref. WT202W LED6S NW PSU S2 PC or equivalent.
443	Supply of Totally enclosed exhaust fan, 300mm sweep continously rated highly efficient heavy-dutymotor similar to Crompton Cat. Ref. Trans Air 12\\" or equivalent.
444	Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. (a) 4 X 16 sq. mm (28mm)
445	(b) 3½ X 35 sq. mm (32mm)
446	Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 95 sq. mm and upto 185 sq. mm
447	Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 95 sq. mm and upto 185 sq. mm
448	Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. Upto 35 sq. mm
449	Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. 300 mm dia
450	Main LT PanelDesign, Manufacturing, Supply, Commissioning & Testing of Main LT Panel. The panel will be totally enclosed type with, free standing, floor mounted, indoor duty, dust & vermin proof, , front operated, electrical panel fabricated from 2 mm thick M.S. Sheet as per specifications & drawing laid in this document and will be complete with the main and auxiliary bus bars, multimeter, indication lamps, CT's, protection MCB, interconnection wiring, earth bus and will be powder coated finish with 50 micron thickness. \\"The Main LT Panel shall use all draw out type breakers suitable for 415 V AC, 3 phase, 50 Hz, 3 phase 4 wire supply system. The panel shall have AMF facility to achieve electrical interlocking, synchronizing, buscoupler switching, auto operation of incommer and bus coupler, auto start of D.G. Sets, auto D.G. running by pre set timing, auto changeover etc and having following incomming and outgoing Air Circuit Breakers, FSU's as per the drawing and specification. Each incoming breaker will have microprocessor based releases and all outgoing breaker will have minimum electrostatic releases over 250A & thermal magnetic release below 250A. The Panel will be made as per detailed specifications & drawings forming part of this document. Fault level of panel shall be 35 MVA. INCOMMER100Amp. 16KA FP With S/C, U/V, E/F Protection MCCB-1 no.BUSBARS1 Nos. 125 Amp FP busbars of aluminium alloy as per SLD.OUTGOING63Amp. 10KA FP MCCB 2+1 No. INSTRUMENTS1 sets of multifunction meter with parameter current,voltage,KWH,KVAH,Power factor on incoming from transformers with RS 485 port.1 Sets of phase indicating lights (RYB) with protection fuses (one set for each incoming breaker).1 Sets breaker 'ON' & 'OFF' indicating lamp (one set for each incoming breaker).1 Sets auto trip indicating lamp .
451	ELECTRIFICATION WORK TOILETWiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C
452	Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
453	Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. (a) 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
454	(b) 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
455	Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. (a) 5/6 A switch
456	(b) 3 pin 5/6 A socket outlet
457	Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75mmX75mm)
458	Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.
459	Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.
460	Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep
461	Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.
462	Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way , Double door
463	Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. (a) Single pole
464	(b) Double pole
465	Supply of 8W Green Perform Sleek is a high performance low-height LED downlighter suited for requirements of any modern professional workspace. Robust PDC housing ensures long system. Narrow rim renders a pleasing aesthetic look. similar to Philips DN295B LED8S-6500 PSU WH or equivalent.
466	Supply of Totally enclosed exhaust fan, 300mm sweep continously rated highly efficient heavy-dutymotor similar to Crompton Cat. Ref. Trans Air 12\\" or equivalent.
467	ELECTRIFICATION WORK FOOR COURTWiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C
468	Wiring for light/ power plug with 2X4 sq. mm FRLS PVCinsulated copper conductor single core cable in surface/recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
469	Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. (a) 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
470	(b) 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
471	(c) 2 X 6 sq. mm + 1 X 6 sq. mm earth wire
472	(d) 4 X 16 sq. mm + 2 X 6 sq. mm earth wire
473	Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.
474	Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm
475	Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. (a) 5/6 A switch
476	(b) 3 pin 5/6 A socket outlet
477	(c) TV socket outlet
478	Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
479	Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75mmX75mm)
480	Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.
481	Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.
482	Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep
483	Extra for fixing the louvers/ shutters complete with frame for aexhaust fan of all sizes.
484	Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, \\"C\\" curve including connections, painting etc. as required.
485	Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 way , Double door
486	Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way (4 + 12), Double door
487	Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. (a) Single pole
488	(b) Double pole
489	Supplying and fixing 40/63A rating, 415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of Four poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Similar to Legrand DX3 AC MCBs or equivalent.
490	Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness
491	Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thickincluding accessories, and providing masonry enclosure withcover plate having locking arrangement and watering pipe of2.7 metre long etc. with charcoal/ coke and salt as required.
492	Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I.pipe from earth electrode including connection with G.I. nut,bolt, spring, washer excavation and re-filling etc. as required.
493	Providing and fixing 25 mm X 5 mm G.I. strip on surface or inrecess for connections etc. as required.
494	Supply of 8W Green Perform Sleek is a high performance low-height LED downlighter suited for requirements of any modern professional workspace. Robust PDC housing ensures long system. Narrow rim renders a pleasing aesthetic look. similar to Philips DN295B LED8S-6500 PSU WH or equivalent.
495	Supply of 15W Green Perform Sleek is a high performance low-height LED downlighter suited for requirements of any modern professional workspace. Robust PDC housing ensures long system. Narrow rim renders a pleasing aesthetic look. similar to Philips DN295B LED8S-6500 PSU WH or equivalent.
496	SITC of 12W Extruded aluminium batten available in 2ft run length with multiple lumen packages and suitable for surface, wall & conduit ounting (with accessories). similar to Philips Type HSN Code MRP (INR) BN 021 LED12S 6500 PSU GR or equivalent.
497	Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.
498	Supply of Pressure die cast housing LED bulkhead with IP66protection and IK09 impact resistance suitable for surface and wall mounting applications. Similar to Philips Cat Ref. WT202W LED6S NW PSU S2 PC or equivalent.
499	Supply of Totally enclosed exhaust fan, 300mm sweep continously rated highly efficient heavy-dutymotor similar to Crompton Cat. Ref. Trans Air 12\\" or equivalent.
500	Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. (a) 4 X 16 sq. mm (28mm)

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents

Also Visit

Tenders

Uttar Pradesh Tenders

Construction Tenders

Building Construction Tenders

Auditorium Construction Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Construction Of Prekshagrih/ Auditorium At Kakor District-Auraiya (U.P.) (Notice No. -39/Uppcl/Gm-7/E-Tender/2025-26 Dated: 08.05.2026), Auraiya-Uttar Pradesh

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Construction Of Prekshagrih/ Auditorium At Kakor District-Auraiya (U.P.) (Notice No. -39/Uppcl/Gm-7/E-Tender/2025-26 Dated: 08.05.2026), Auraiya-Uttar Pradesh

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us