|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. All kinds of soil |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m . All kinds of soil |
| 4 | Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading torequired slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete. |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - -All work upto plinth level (i) 1:3:6 ( 1 Cement: 3 fine sand : 6 graded well burnt brick aggregate 40 mm nominal size) |
| 6 | Centering shuttering including struttings, propping etc. and removal of form work for: Suspended floors, roofs, landings, balconies and access platform with 12 mm thick shuttering ply |
| 7 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - -All work upto plinth level1:2:4 ( 1 Cement: 2 fine sand : 4 graded stone aggregate 20 mm nominal size) |
| 8 | First class brick work in foundation and plinth including cost of all materials as required complete:- In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 9 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 10 | Dismantling old plaster or pointing, raking out joints, cleaning and preparing the surface for re-plastering or re-pointing including disposal of rubbish to the dumping ground with all leads and lifts etc.complete as per direction of the Engineer- in Charge. |
| 11 | 12 mm cement plaster of mix(1) In cement mortar 1 : 4 ( 1 cement : 4 fine sand ) |
| 12 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 fine sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.. 18 mm thick stone slab |
| 13 | Providing and fixing decorative plywood 4 mm thick one side decorative veneer conforming to IS: 1328 (type-1) for plain lining / cladding with necessary screws, priming coat on unexposed surface with: Decorative veneer facings of approved manufacture. |
| 14 | Removing dry/oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. as required. |
| 15 | Providing & apoplying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even & smooth complete |
| 16 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications [Payment shall be made after submission of Test Certificate issued by the Manufacturer]: Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm |
| 17 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer]: . Two or more coats on new work over an under coat of suitable shade with ordinary paint (primer) of approved brand and manufacture |
| 18 | Finishing walls with textured exterior paint of required shade of approved brand and manufacture on old work ( one or more coats ) including preparation of surface as required complete as per direction of the Engineer in charge. |
| 19 | Varnishing with varnish ( one or more coats of glue sizing ) of approved brand and manufacture on old work including preparation of surface as required complete as per direction of the Engineer in charge:- With copal varnish. |
| 20 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture ( conforming to IS :6315 )having brand logo embrossed on the body/plate with double spring mechanism and door weight uopto 125 kg for doors,including cost of cutting floors,embedding in floors as required and making good the same matching to the existing floor finishining and cover plates witrh brass pivot and single piece MS sheet outer box with sliude plte etc complete as per direction of the engineer -in -charge.(16.4.1)With stainless steel cover plate minimum 1.25 mm thickness. |
| 21 | Providing and fixing stainless steel ( SS 304 grade ) adjustable friction window stay of approved quality with necessary stainless steel screws etc. to the side hung windows etc. complete as per direction of Engineer-incharge: 255 x 19 mm. |
| 22 | Providing and fixing 100 mm brass locks (best make of approved quality) with 6 levers without pair of handles for aluminium doors including necessary cutting and making good etc. complete as per direction of Engineer in-charge. |
| 23 | Providing and fixing hard drawn steel wire fabric of size 75 x25 mm mesh or other suitable size wire mesh to be fixed & firmly anchored to the concrete surface by means of \\"L\\" shaped mild steel shear key welded with existing reinforcement including the cost of materials, labour, tool & plants, as required and as per direction of the Engineer-in-charge. |
| 24 | Providing and fixing aluminium work for doors,windows, ventilators, stair railing including hand rail andpartitions with extruded built up standard tubularsections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with requiredPVC/neoprene felt etc. aluminium sections shall besmooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawing and the direction of Engineerincharge. (Glazing and paneling to be paid for separately) :- 16.1.1 For fixed portion of approved quality:- 16.1.1.1 Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). |
| 25 | Providing and fixing glazing of approved quality in aluminium doors, windows, ventilator, shutters and partition frames with PVC / neoprene gasket etc. complete as per architectural drawing and the direction of Engineerin- charge :- With glass/ float glass panes of 4.0 m thickness ( weight not less than 10.0 kg / sqm ) |
| 26 | Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc complete |
| 27 | Providing and fixing IS : 3564 marked aluminium extruded section body tubular type universal hydraulic door closer with double speed adjustment with necessary accessories and screws etc. complete. |
| 28 | Providing and fixing bright finished brass handles with screws etc. complete : 125 mm |
| 29 | Providing and fixing bright finished brass towerbolts (barrel type)with necessary screws etc. complete : 250 x 10 mm |
| 30 | Providing wood work in frames of doors, windows,clerestory windows and other frames, wrought framedand fixed in position :Local Teak wood |
| 31 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veeners on both faces of shutters:35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. |
| 32 | Providing and fixing on wall face unplasticised rigid PVC rain water pipes (working pressure 4 kg/cm2) conforming to IS 13592 type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expantion (i) Single socketed pipe- 110 mm OD |
| 33 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type-A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion etc. complete as per direction of Engineer-in-charge : Coupler:110 mm |
| 34 | Single equal tee with door 110mmx110mmx110mm |
| 35 | (iii) Bend 87.5 |
| 36 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :(i) White Vitreous china Orrisa pattern W.C. pan of size 580x440 mm with integral type foot rests. |
| 37 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 18.18.1. 10 litre capacity-White |
| 38 | Providing and fixing C.P. brass stop cock ( concealed) of standard design and approve make conforming to IS : 893115 mm nominal bore |
| 39 | Providing & fixing superior quality Pillar cock for wash basin of approved brand.(Agt No:07/CE,PWD(R&B) Approved rate vide letter no: 23(71)/SE-II/2011-12 Dated 06-07-2018. |
| 40 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Flexible pipe 32 mm dia |
| 41 | Providing & fixing superior quality white vitreous china wash basin with full pedestal in/c making all connection but excluding the cost of fittings Size-610X465X160 mm(Agt No: 07/CE,PWD(R&B) Approved rate Vide letter No: 23 (71)/SE-II/2011-12 dated 06-07-2018 |
| 42 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 43 | Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete |
| 44 | Providing and fixing unplasticised PVC connection pipe with brass unions: 30 cm length(i) 15 mm nominal bore |
| 45 | (ii) 20 mm nominal bore |
| 46 | Providing and fixinggun metal gate valve with C.I. wheel of approved quality ( screwed end):(i) 25mm nominal bore |
| 47 | (ii) 40 mm nominal bore |
| 48 | (iii) 50 mm nominal bore |
| 49 | Providing & fixing superior quality Bib cock of approved brand with wall flange(Agt No: 07/CE,PWD(R&B) Approved rate Vide letter No: 23 (71)/SE-II/2011-12 dated 06-07-2018 |
| 50 | Centering shuttering including struttings, propping etc. and removal of form work for Columns, Pillars, Piers, Abutments, Posts and Struts with shuttering ply |
| 51 | Providing structural steel work in single section fixed with or without connecting plate including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete as required. |
| 52 | Providing corrugated G.S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required etc. complete as per direction of Engineer-in-charge. 0.63mm thick with zinc coating not less than 275gm/m2 |
| 53 | labour charge for lifting of 5000 to 20000 GPH water lubricated vertical submersible pump motor in/c column assembly upto 100 feet with heavy duty chain pilley and block as per direction of the Engineer-in-charge. |
| 54 | Providing & fixing gun metel gate valve with CI wheel of approved quality (screwed end). (a) 40 mm dia nominal bore |
| 55 | Supplying & fitting fixing of PVC insulated copper wire with all electrical equipments including trial run etc. complete (ISI Marked) on the pannel board of approved quality. 7/16 Copper Wire |
| 56 | Providing and fitting fixing of Fully Automatic Star Delta type Motor starter ( 3 ph. 50 Hz, 415V, in Steel Sheet Enclosures with Contractors and Timer etc. complete suitable for submersible Pump L & T, BCH, ABB make as per specification and direction of the Engineer-in-charge. 35 HP/26 kw Relay range within 20-32 + 10% |
| 57 | Providing and fitting fixing steel sheet enclosed switch fuse unit (suitable for DIN fuses), triple pole with Neutral Link (TPN), 415/500 Volt, L & T / Havells / BCH make etc. complete as per specification and direction of the Engineer-in-charge. 63 amps |
| 58 | Repair and maintenance of 20/22.5 HP Motor suitable for 10000 GPH capacity submersible pump set by dismantling in/c providing & fixing of PVC (Is: 8783-1978 ) insulated electro grade copper (IS:613-1984) conductor winding in stator & all necessary spare parts and reassembling the same in/c servicing of rotor & necessary trail run as per specification & direction of the Engineer-in-charge. |
| 59 | labour charge for Lowering & fitting fixing of 5000 to 20000 GPH water lubricated vertical submersible pump motor in/c column assembly upto 100 feet with heavy duty chain pulley and block and making necessary electrical connection with main switch/ starter with motor in/c trial run for 10 hrs in two spell complete as per direction of the Engineer-in-charge. |
| 60 | Providing & fixing of 25 mm dia PVC insulated 3 core flat copper cable conforming to relevant IS code for submersible motor all necessary equipments and fittings as required as per specification & direction of the Engineer in charge (i) 4.0 sqmm |
| 61 | Providing and fitting fixing of Fully Automatic Star Delta type Motor starter ( 3 ph. 50 Hz, 415V, in Steel Sheet Enclosures with Contractors and Timer etc. complete suitable for submersible Pump L & T, BCH, ABB make as per specification and direction of the Engineer-in-charge. 25 HP/18.5 kw Relay range within 13-21 + 10% |
| 62 | Rewinding of Horizontal Motor suitable for centrifugal pumps by complete dismantling in/c providing & rewinding with Super enamelled copper conductor (as per IS : 13730 Part-3 ) conductor & all necessary spare parts and reassembling the same including servicing of rotor & necessary trial run as per specification and direction of the Engineer-in-charge. (i) 2.0 HP |
| 63 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of grith upto 30cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50m outside the periphery of the area cleared. |
| 64 | Operation of plant by deploying pump operator and helper in/c operation of Sluice valves of the plant including Chlorination,alumn dosing clarifaculator,back washing Cleaning of total plant as per requirment as well as direction of the Engineer in Charge.a) Pump-operator (1 person) |
| 65 | b) Helper (1 person) |
| 66 | Cleaning of terrace/loft water storage tank (inside surfacearea)upto2000litre capacity at all heightswith coconut brushes, duster etc., removal of silt, rubbishfromthe tankandcleaning the tankwithfresh waterdisinfecting with bleaching [email protected] litre capacity of tank,including marking thedate of cleaning on the side of tank body withthe help of stencil andpaint and disposing of malba, all complete as perdirectionof Engineer-in-Charge. (Theold date already writtenon tank should beremoved with paint removerorblackpaintandifdateisnotwrittenwiththestencilorolddate is not removeddeductionwill bemade@Rs. 0.10per litre i fduring cleaning any G I fittingsor ball cock is damaged that is to be repaired by contractor at his owncost andnothingextrawill be paid on this account) |
| 67 | Providing & fitting, fixing of new Screens for all Openings at Pragna Bhaban as per direction of the Engineer-in-charge. Please Enable Macros to View BoQ information |
