|
| 1 | M & L for Preparation of old plastered or unplastered surfaces of wall including cornices, pillasters by brooming down with steel wire brushing scrapping down smoke dust, moulds, moss and efflorescent salts and removing oily and greasy spots etc applying one coat of white wash with auto paint roller on old surfaces of walls complete and all as specified |
| 2 | All as per ser item No 1, above but on ceiling surface complete and all as specified. |
| 3 | M&L Complete removal of existing treatment by using vacum based sanding machine on wall including scraping,removing all muds crack with wire brush where required and gunny bags from old surface free from any depression. Complete all as specified and directed by engineer-in-charge. Note:-(i) All the wall/floor and surrounding to be made clean after applying OBD/camouflaging painting to the entire satisfactory of Engr-in-charge. (ii) Due care should be taken by the contractor for cover of furniture already existing in the Buildings. |
| 4 | M&L Preparation of old plastered or unplastered surfaces of wall including cornices, pillasters by using vacum based sanding maching to remove all smoke dust,moulds,moss and efflorescent salts and removing oily and greasy spots etc applying one coat of distemper oil emulsion of shade as approved by Engr-in-charge with auto paint roller on old surfaces of walls all as specified and directed. Note- Surface to be made even and smooth by filling the depression if any. |
| 5 | M&L two coats of distemper oil emulsionon allready preprade surfaces, of shade as approved by Engr-in-charge by auto paint roller over a coat of primer on prepared surface to make the surface smooth without any marks complete all as specified and directed by Enge-in-charge. Note:-(i) All the wall/floor and surrounding to be made clean after applying OBD/camouflaging painting to the entire satisfactory of Engr-in-charge. (ii) Due care should be taken by the contractor for cover of furniture already existing in the qte/Bldg. |
| 6 | M&L Two coats of plastic emulsion paint (to be applied with auto roller) over a coat of primer including preparing the surface by vacuum based sanding machine and applying a coat of 2mm thick wall ware puttty making the surface even and smooth free from any depression/hole/nails complete all as specified and directed by Engr-in-charge. Note:-(i) All the wall/floor and surrounding to be made clean after applying OBD/camouflaging painting to the entire satisfactory of Engr-in-charge. (ii) Due care should be taken by the contractor for cover of furniture already existing in the qte/Bldg. |
| 7 | All as per item 05, above but on ceilling complete all as specified and directed all as specified and directed by Engineer-in-charge.Note:-(i) All the wall/floor and surrounding to be made clean after applying OBD/camouflaging painting to the entire satisfactory of Engr-in-charge. (ii) Due care should be taken by the contractor for cover of furniture already existing in the qte/Bldg. |
| 8 | M & L preparation of old steel surfaces exc 10cm width or grith and applying one coat of synathetic enamel paint complete all as specified. .Note:-(i) All the wall/floor and surrounding to be made clean after applying OBD/camouflaging painting to the entire satisfactory of Engr-in-charge. (ii) Due care should be taken by the contractor for cover of furniture already existing in the qte/Bldg. |
| 9 | M & L preparation of old wood or wood based surfaces and One coat of synathetic enamel paint all as specified and directed.Note:-(i) All the wall/floor and surrounding to be made clean after applying OBD/camouflaging painting to the entire satisfactory of Engr-in-charge. (ii) Due care should be taken by the contractor for cover of furniture already existing in the qte/Bldg. |
| 10 | Taking down cement or cement lime plasteron brick or stone walls etc.including raking out joints,hacking for key,scrubbing down with water,etc. in any position all as specified and directed..Note:-(i) All the wall/floor and surrounding to be made clean after applying OBD/camouflaging painting to the entire satisfactory of Engr-in-charge. (ii) Due care should be taken by the contractor for cover of furniture already existing in the qte/Bldg. |
| 11 | M & L Rendering 15mm thick cement plaster on faces of brick work or concrete surfaces in cement mortar (1:6) furnished even & fair using extra cement all as specified and directed by Engr-in-charge. |
| 12 | M&L for 15mm thick cement plaster in CM 1:4 on bricks or concrete surfaces finishing the surfaces even and smooth without using extra cement as directed all as specified Note rate for form work if reqd to be incl in the quaoted by the contractor. |
| 13 | Rendering dubbing coat over damaged irregular surface of patches at colms,chajja,canopy and soffits, roof projections ceiling facia etc using GI Chiken Mess of size 0.25mm thick and 20mm aparture fixed with nails including necessary scaffolding arrangement as required at site average 15mm thick incm 1:4 over cement slurry coat thick @ 3 Kg/Sqm making the surface even followed by 5mm hick rendering in CM 1:3 furnished even and smooth including applying two coats of weather proof emultion paint incl making of drip course as reqd complete incl roughening surface of old concrete by picking sweeping clean and washing with water all Complete all as directed by Engr-in-charge Note rate for form work if reqd incl in the rate quaoteed by the contractor. |
| 14 | M&L applying two coats of acrylic exterior emulsion paint as approved of any shade pattern in camouflage pattern over a coat of primer including preparation of newly plastered surfacessurfaces as per manufacture instructions complate all as specified and as directed. Note Removing of vegitation/plantation requird for carring the work deemed to be included in the rate coated by contractor. |
| 15 | M&L Preparation of newly plastered surfaces and applying two coats of oil bound distemper, over a coat of primer including chalk whitening on plastered surfaces of walls complete all as specified and as directed. |
| 16 | M & L for cutting and widending existing cracks in V-shape not exc 1 cm in grith in wall and than filling in with \\"Crack-X\\" of Pidilite or equivalent including making good to facings complete all as specified directed by Eng-in-Charge. |
| 17 | M&L applying 2-3mm thick Altek/Birla white wall care putty on wall/ceilling to obtain smooth surfaces and even finish by using vacume based sanding machine,including preparation of surfaces etc. Please Enable Macros to View BoQ information |
