|
| 1 | Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in hard dense Soil complete all as specified and directed. |
| 2 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and getting out in hard/dense soil complete all as specified and directed. |
| 3 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. complete all as specified and directed. |
| 4 | Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed. |
| 5 | M & L for Cement concrete type D-2, 1:4:8 (Using 40mm graded crushed stone aggregate) in foundations, filling and mass concrete complete all as specified and directed. |
| 6 | M & L for RCC M30 ( Design Mix ) (Using 20mm graded crushed stone aggregate) in footing, plinth beam complete all as specified and directed. |
| 7 | Use and waste of Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter flat rough finished surface of concrete omplete all as specified and directed. |
| 8 | M&L for RCC M-30 (Design Mix) (Using 20mm graded crushed stone aggregate) in Columns, pillars, piers, posts and struts complete all as specified and directed. |
| 9 | Use and waste of Formwork to sides of pillars, posts, struts, piers, columns and stanchions for fair finished surface square, rectangular complete all as specified and directed. |
| 10 | M&L for RCC M30 (Design Mix) (Using 20mm graded crushed stone aggregate) in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed. |
| 11 | Use and waste of Formwork flat and fair finished to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels beam, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed. |
| 12 | M & L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 13 | M & L for 5mm dia Mild steel TMT bar and over upto and including 10mm dia in stirrups, spacers and binders cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 14 | Supply only water proofing compound (integral) all as specified & directed. |
| 15 | M&L Pre-cast cement concrete block masonry type C-1 1:3:6 (20mm graded crushed stone aggregate) with solid blocks, exc. 10cm in width and, setting in cement mortar 1:6 complete all as Specified and directed. |
| 16 | M&L Pre-cast cement concrete block masonry type C1 1:3:6 (20mm graded aggregate) with solid blocks, 10cm in thick and, setting in cement mortar 1:4 complete all as Specified. |
| 17 | M&L for 10 mm thick rendering in cm (1:6) on fair faces of brick work or concrete surface (Internal Plaster ) finished the surface even & smooth without using extra cement, complete all as specified and directed. |
| 18 | M&L for 15 mm thick rendering in cm (1:4) on fair faces of brick work or concrete surface finished the surface even & smooth without using extra cement, complete all as specified and directed. |
| 19 | M&L for preparation of newly plastered wall/pillasters/vertical surface and applying two coats of cement base paint over a coat of alkali resistance primer complete all as specified and directed. |
| 20 | M&L preparation of new plastered or unplastered surfaces and applying two coats of oil bound distemper on wall over a coat of alkali resistant primer complete all as specified and darected. |
| 21 | S&F Plain solid straight chowkats or frame rounded or chamfered put together with glue pined at joints with 1st class hard wood complete all as specified and directed. |
| 22 | S&F for 30mm thick 1st class hardwood Plain, framed, panelled door shutters(any number of panels), with panels of timber flat on both sides (feather edged), veneered particle board medium density, wood particle board with commercial face veneers, supplied and fitted to chowkats complete all as specified and directed. |
| 23 | S&F solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tubes, as per specifications and drawing complete or as directed by Engineer-In-Charge. |
| 24 | S&F factory made solid PVC door shutter 30mm thick (stiles), consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC strip of 20mm width stuck in insde with solvent cement for stiles and plain colour PVC sheets for top rail; lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and directed. |
| 25 | S&F aluminium anodised window and ventilator shutter, side hung type without sash bars aiuminium section weighting 0.55 kg/m including nessary joint cleats, glazing clips, ruber neoprene packing, aluminium snap beading screw anodised alumimium fittings such as peg stays 150mm long (1 No), hinges type B-21 100mm long (02 Nos), suitable handle (01 No), complete all as specified and directed. |
| 26 | M&L 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed. |
| 27 | S&F of 100mm size, butt hinges, cold rolled steel with screw, medium weight , ISI marked complete all as specified and directed by Engr-in-Charge. |
| 28 | S&F of 75mm size, butt hinges, cold rolled steel with screw, medium weight , ISI marked complete all as specified and directed by Engr-in-Charge. |
| 29 | S&F 150mm long Aluminium, anodised, barrel tower bolt, fixed with screws complete all as specified and directed by Engr-in-Charge. |
| 30 | S&F 150mm size, extruded aluminium alloy handles fabricated type anodised complete all as specified and directed by Engr-in-Charge. |
| 31 | S&F of 250mm long, aluminium alloy, anodised,sliding door bolts, with hasp staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast-aluminium alloy complete all as specified and directed by Engr-in-Charge. |
| 32 | M&L for preparation of new or previously untreated wooden surfaces of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint (1st grade quality) over a coat of pink primer complete all as specified and directed by Engr-in-Charge. |
| 33 | S&F vitreous china water closet (squatt pan) orrisa pattern 580x440 mm (IWC) size pan white with front or back inlet with integral 'foot rests including provn of lime concrete bedding including connections to 'flushing cistern/pipe complete all as specified and directed including 100mm CI 'P' trap etc complete all as specified and directed. |
| 34 | S&F PVC 10 Ltrs valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete with 32 mm dia flush pipe connecting to squatt pattern etc. ISI approved etc complete all as specified and directed. |
| 35 | S&F viterous china wash hand basin (WHB), white flat/angle back size 630 x 450mm with padestal tall etc complete all as specified and directed. |
| 36 | S&F in repairs for Vitreous China bowl type urinals, size of 465x355x265mm white(minimum) with grating and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (excluding of fixing supply pipe, flushing cistern, flush pipe, trap and waste pipe) complete all as specified and directed. |
| 37 | S&F 20mm 3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc complete all as specified and directed |
| 38 | S&F 16mm 3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc complete all as specified and directed. |
| 39 | S&F 15 mm bore Angle cock, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe and fixed.complete all as specified and directed by engr-in-charge |
| 40 | S&F bib tabs 15mm dia cast copper alloy with capstan head handle fancy type screwed down for iron pipe or for brass ferrule complete all as specified and directed. |
| 41 | S&F 15mm bore pillar taps CP brass chromium plated fancy type screwed down high pressure with chromium plated screwed shanks and fly nuts complete screwed for iron pipe complete all as specified and directed. |
| 42 | S&F stop valves 15mm bore chromium plated, cast copper alloy screwed down high pressure with capstan head handle screwed both ends for iron pipe or for union complete all as specified and directed. |
| 43 | S&F PVC connection 15 mm size with PTMT nuts of length 450mm fixed complete all as specified and directed. |
| 44 | S&F corrugated flexible PVC waste pipe of 32mm dia, 800mm long complete all as specified and directed by Engr-in-Charge. |
| 45 | S&F of soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed. |
| 46 | S&F in repairs 20mm dia brass chromium plated tubular towel rails, D type, 60cm long between flanges, complete all as specified and directed by Engr-in-Charge. |
| 47 | S&F 600mmX450mm bevelled edge mirror 5 mm thick of selected quality glass, mounted on 6mm thick AC building board or comercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washer and taking down old mirror complete all as specified and directed. |
| 48 | S&F rotational moulded polythylene water storage tanks 1000 ltrs ( cylindrical vertical with closed top) hoisted and fixed in position all specified complete all as specified and directed. |
| 49 | S&F 75mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. |
| 50 | S&F 75mm dia bore PVC (SWR) bends complete all as specified and directed.complete all as specified and directed by Engr-in-Charge. |
| 51 | S&F 75mm dia bore PVC (SWR) junction single, (single T) equal or unequal complete all as specified and directed. |
| 52 | S&F 75mm dia PVC (SWR) floor trap plain with grating including jointing to waste pipe fixed in solvent cement or cement concrete 1:2:4 type B1 complete all as specified and directed. |
| 53 | S&F 110mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. |
| 54 | S&F 110mm dia bore PVC (SWR) junction single, (single T) equal or unequal complete all as specified and directed. |
| 55 | S&F 110mm dia bore PVC (SWR) bends complete all as specified and directed.complete all as specified and directed by Engr-in-Charge. |
| 56 | S&F PVC(SWR) gully trap 110mm, setting and jointing with solvent cement complete all as specified and directed. |
| 57 | M&L for Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed. |
| 58 | M&L for 100mm thick Cement concrete type D- 2, 1:4:8 (Using 40mm graded crushed stone aggregate) in sub base complete all as specified and directed . |
| 59 | M&L for 25mm thick Cement concrete type B- 2, 1:2:4 (Using 20mm graded crushed stone aggregate) in floor to recive tile complete all as specified and directed. |
| 60 | M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bedding in CM 1:6. for laying floor finishes receiving floor tiles complete all as specified and directed. |
| 61 | M&L for Coloured glazed ceramic tiles in vertical surface of size 450x300x7mm thick set and jointed in net cement slurry and pointed in white or color cement and 10mm thick backing coat of brick/concrete surface in CM 1:4 complete all as specified and directed by Engr-in-Charge. |
| 62 | M&L for 75mm thick Cement concrete type B-1, 1:2:4 (Using 40mm graded crushed stone aggregate) in plinth protection complete all as specified and directed. |
| 63 | M&L for MS plate fe 410 (Gde E-250) plain/ checqured square cut or notched (ordinary and counter sunk forming holes without any attachment complete all as specified and directed by Engr-in-charge. |
| 64 | M&L for rolled mild steel as in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat, plate sections) including distance pieces, cleats etc Grade of Fe 410-w Gde (E-250) complete all as specified and directed by Engr-in-charge. |
| 65 | M&L for preparation of new painted steel surfaces apply one coat of Red Oxide Zine Crome Primer and applying two coat of synthetic enamel paint on surface of any description over 10cm width or girth complete all as specified and directed by Engr-in-Charge. (Note : Ladders, scaffolding will be provided by Contractor where required) |
| 66 | S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm long |
| 67 | S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 68 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 69 | Excavating over areas, n exc 1.5 m deep and getting out in hard/dense soil complete all as specified and directed by Engineer in Charge. |
| 70 | Excavating over areas, exc 1.5 m and n.exc. 3.00m deep and getting out in hard/dense soil complete all as specified and directed by Engineer in Charge. |
| 71 | Excavating over areas, exc 3 m and n.exc. 4.50 m deep and getting out in hard/dense soil complete all as specified and directed by Engineer in Charge. |
| 72 | M&L for PCC 1:3:6 type C-2 (Nominal Mix) 150mm thick using 40 mm graded stone aggregate as in foundation filling mass concrete and similar work complete all as specified and directed by Engineer in Charge. |
| 73 | M&L for Walling of random rubble stone masonry, uncoursed, well bonded, bedded and solidly hearted, build in cement mortar 1:4 complete all as specified and directed by Engineer in Charge. |
| 74 | M&L for Walling of random rubble, uncoursed, well bonded, laid dry in retaining walls, abutments and similar work complete all as specified and directed by Engineer in Charge. |
| 75 | M&L for providing RCC type B-1 1:2:4 using 20 mm graded aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as complete all as specified and directed by Engineer in Charge. . |
| 76 | M&L for formwork to soffits of suspended slabs, flat, such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) etc rough finished surfaces of concrete complete all as specified and directed by Engineer in Charge. |
| 77 | M&L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide ® rough finished surfaces of concrete complete all as specified and directed by Engineer in Charge. . |
| 78 | M&L for precast reinforced cement concrete 1:2:4 type B1 (using 20 mm graded agg) as in cover slab for manholes set in CM 1:4 including necessary form work complete all as specified and directed by Engineer in Charge. |
| 79 | M&L Concrete bed 1:4:8 type D-2 to drain pipes incl packing under and haunching against the sides of pipes after they are laid and tested bore of pipe in 110 mm.complete all as specified and directed by Engr in Charge. |
| 80 | S&F PVC(SWR) vent cowl of dia 75 mm complete all as specified and directed by Engineer in Charge. |
| 81 | M&L Hardcore of guage exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface in broken stone or boulders complete all as specified and directed. |
| 82 | M&L for 100mm thick cement concrete type C-2, 1:3:6 using 40mm graded stone aggregate as sub base complete all as specified and directed by Engr-in-Charge |
| 83 | M&L for 15mm thick Screed bed or bedding layer of mortar in CM 1:6 for laying floor finishes complete all as specified and directed by Engr-in-Charge. |
| 84 | M&L for Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigments complete all as specified and directed by Engr-in-Charge. |
| 85 | M&L for Painting lines, dashes, arrows, letters, etc on roads , pavements and the like exc 10cm wide with road marking paint white, black and golden yellow with adequate nos of coats complete all as specified and directed by Engr-in-Charge. |
| 86 | M&L Providing, cement concrete in roof kerbs or mud stops, rounded or chamfered on edges (above wall for coping) Type C- 1, 1:3:6 (using 20mm graded crushed stone aggregate) complete all as specified and directed. |
| 87 | M&L for pillar/cloumn in tubular section inc special shaped washer etc complete using ERW or induction butt welded tubes confirmiing to IS 1161-1979 grade of steel Fe 410-w Gde (E-250) complete all as specified and directed by Engr-in-charge. |
| 88 | M & L for Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M30 grade with approved colour design and pattern as in footpath, parkes, lawns, drive way parking etc of required srength thickness and size/ shape made by table vibratory method using PU moulds, laid in required colur and pattern over and including 15 mm thick compact bed of courde sand compacting and proper embedding/ laying of interlocking [paver block into the sand bedding layer through vibratory compaction by using plate vibrator filling the joint with fine sand and cutting paver block as per required size and pattern finshing and sweeping extra sand complete all as specified and directed by Engr-in-Charge |
| 89 | M&L for 75 mm thick PCC (1:3:6) type C2 using 40mm graded stone aggregate as in plinth protection finishing the surface even and smooth without using extra cement Complete all as specified and directed. |
| 90 | Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs blankets any thickness, including cover fillets complete all as specified and directed by Engr-in Charge |
| 91 | M&L 9 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with nails to timber frame work in walls complete all as specified and as directed by E-in charge . |
| 92 | S&F grid false ceiling GI system powder coated prelude (main runner section 32x24x0.30x3600mm, cross tee 25x24x0.30x1200mm, wall angle 24x24x0.40x3000mm and including providing and fixing PVC pre-laminated in frontside and aluminium foil backed gypsum tile board of size 595 x 595 x 8-9mm fixed in ceiling frame work with necessary fastening GI wire and cleats complete all as specified and directed by Engr-in-Charge. |
| 93 | Dismantling of timber fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section frame workcomplete all as specified and as directed by E-in charge . |
| 94 | M&L second class hard wood timber scantling plain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brads, sectional area exc. 13 Sq cm n.exc 25 Sq cm secured with nails or brads.complete all as specified and as directed by E-in charge . |
| 95 | M&L second class hard wood timber scantling bullnosed, splayed,chamfered or rounded on one edge or face, secured with nails or brads, sectional area exc. 3 Sq cm n.exc 6 Sq cm secured with nails or brads.complete all as specified and as directed by E-in charge . |
| 96 | S&F in repair 15 mm bore bib tap brass chromium plated fancy type with crutch or butterfly handle screwed down, screwed for iron pipe complete all as specified and directed. |
| 97 | Demolition of Brickwork / concrete block or stone/ boulder masonry, built in cement mortar complete all as specified and directed by Engr-in-Charge. |
| 98 | M&L Pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width and setting in mortar, complete type C1 1:3:6 (20 mm graded agg) set in CM 1:4 completed all as specified and directed by Engr-in-charge . |
| 99 | Dismantling plain or corrugated steel sheeting any guage, thickness including nainital or similar pattern roof covering and wall cladding complete all as specified and directed by Engr-in-Charge. |
| 100 | S&F 0.63 mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275.complete all as specified and directed by Engr-in-Charge. |
| 101 | Dismantling wrougth iron or mild steel work of any description not otherwise provided complete all as specified and directed by Engr-in-Charge. |
| 102 | S&F in repairs 15 mm bore stop valves, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. |
| 103 | Taking up or down 20 mm dia steel tubing and connections, complete all as specified and as directed by the Engr-in-Charge |
| 104 | Taking up or down 25 mm dia steel tubing and connections,complete all as specified and as directed by the Engr-in-Charge |
| 105 | S&F 3 layer PP-R Polypropyene ransom copolymer outer dia of pipe 25 mm pipes SDR 7.4 (PN-16) UV stablized and anti microbial fusionwelded having thermal stavility for hot & cold water supply including all PPR plain & brass threaded polypropylene random fittings fixed complete to walls, celling or in floors etc complete all as specified and directed by the Engineer -in-Charge |
| 106 | S&F in repair Viterous China WHB 550 x 400 mm pedastal type including cutting for and pinning in ends of brackets or erecting stand with and including of CP Pillar tap 15mm, CP Waste coupling 32mm, PVC waste pipe 750mm long and brackets complete all as specified and directed by engr-in-charge. |
| 107 | S&F in repair in PVC connections 15mm size with PTMT nuts of length 300mm complete all as specified and directed by Engr-in-Charge. |
| 108 | S&F in repair 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and as directed by Engr-in-Charge |
| 109 | S&F in repair 25 mm bore Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed.complete all as specified and directed by engr-in-charge. |
| 110 | S&F in repairs Sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed by Engr-in-Charge. |
| 111 | Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing) removing dismantled tile and rubbish off the premises complete all as specified and directed by Engr-in-Charge. |
| 112 | Demolition Stone slabs and tiles Laid beded and pointed cement mortar of any description or thickness in floors, aprons etc. all as specified and directed by Engr-in Charge. |
| 113 | M&L Granite 25 mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and Providing edge moulding to 18-20mm thick granite stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and directed by Engr-in-Charge. |
| 114 | S&F in repair Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle,Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 115 | S&F Sheet glass of size 5.5 mm thick ordinary quality and glazing with with beads fixed with metal panel pins/neoprene beadings, size of pane/ partition n exc 0.5 sq. m in each. |
| 116 | M&L for point wiring (Concealed type) complete with PVC insulated, sheathed stranded copper conductor (multistrand) of size 1.5 sqmm, 1100 volts grade conforming to IS 694/90, along with one single run of same size and type of copper wire as continuous earth wire to common earth dolly and supply and fixing rigid non metalic ISI marked PVC conduit pipe medium grade of size not less than 20 mm dia along with all accessories and fittings such as bends, tees, elbow etc, junction boxes including sunk terminal boxes, new 3 mm thick laminated sheet cover with brass screw and cup washers with all accessories and including cutting and chasing work on brick wall not exceeding 10 cm girth and making good to disturbed surfaces with cement mortar ratio 1:3 and treated surface with white/colour wash / OBD / Plastic paint to match with existing surface complete all as specified and directed for the following :-One light point or one fan point controlled by one way, single pole switch |
| 117 | All as per item Srl No. 116.00 here-in-before but for one socket outlet 3 pin, 5 Amps on same board. |
| 118 | All as per item Srl No. 116.00 here-in-before, but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor (Multi-stranded) insulated and unsheathed electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 1.5 Sqmm copper stranded conductor as continuous earth wire connected to common dolly complete all as specified and as directed by Engineer-in-Charge. |
| 119 | Supply and fixing switch piano flush button single pole one way 5 Amps complete |
| 120 | Supply and fixing switch, socket combination 2 in 1, 5 Amp, flush type complete all as specified and as directed by Engr-in-charge. |
| 121 | Supply and fixing switch socket combination multi purpose 2 in 1, 3 pin 5A/16A, 5 in 1 flush type complete all as specified and as directed by Engr-in-charge. |
| 122 | Supply and fixing ceiling rose, surface bakelite, 65 x 50 mm, three terminals complete all specified and as directed by the Engineer-in-Charge. |
| 123 | Supply and fixing LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete |
| 124 | Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete. |
| 125 | S&F Lamp holder, metal cased, bakelite body, 230 volts, complete all as specified and directed. Make : Cona / Havells (Rio)/ SSK |
| 126 | S&F LED lamp 9/10W complete all as specified and directed by the Engineer-in-Charge. Make : Havells / Crompton / Philips |
| 127 | S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size. |
| 128 | S&F exhaust fan heavy duty 300 mm sweep, 1 Phase 1400 rpm including louvers and grounting with nut bolts complete all as specified and directed by Engr-in-charge. (Make : Crompton / Orient / Khaitan ) |
| 129 | S & F electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated and timer setting, complete with all accessories such as safety valve, thermostate, NRV, connection piece, etc. complete all as specified and as directed by Eng- in-charge. |
| 130 | Supplying & Laying, connecting and testing , tube medium grade, galvanised with all fittings and fixed complete to walls and ceiling or laid in floors if size 15 mm dia, all as specified and as directed by Engr-in-Charge. |
| 131 | S&F stop valve, cost copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union and fixed of size 15 mm complete all as specified and as directed by Engr-in-Charge. |
| 132 | S&F Bib taps, Chromium plated , fancy type, screwed down, screwed for iron pipe or for brass ferrule and fixed of size 15 mm complete all as specified and as directed by Engr-in-Charge. |
| 133 | S&F PVC connection for Hot Water 15mm with CP nuts and bolts and washers of length 600mm complete all as specified and as directed by Engr-in-Charge. |
| 134 | S&F PVC connection for cold Water 15mm with CP nuts and bolts and washers of length 750 mm complete all as specified and as directed by Engr-in-Charge. |
| 135 | M&L for point wiring with PVC insulated, PVC unsheathed FR cable 1100 V grade , single core, stranded, copper conductor cable 4 sqmm size, drawn into including non metallic rigid PVC Casing-N-Caping (ISI marked) medium grade not less than 25 mm with all casing-n-caping accessories in surface and including PVC unsheathed FR cable 2.5 sqmm stranded copper cable (green insulation) for continuous earth wire and including pressed steel concealed terminal boxes of required size of 1.6 mm thick, covered with 3 mm thick plastic laminated bakalite sheet, ISI marked all as directed. Note : Wiring to be done through Casing-n-caping in walls and surface conduit in Roof/Pipes. |
| 136 | S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp complete all as specified and as directed by Engr-in-Charge. |
| 137 | S&F of DB, double Door, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, SPN 8 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof, suitable for incorporation of MCB’s and isolators etc and making all necessary connections, duly flush of wall surface, complete all as specified and directed. Make : Schneider Elect / Legrand / C&S / Hager |
| 138 | Supply and fixing MCB single pole and neutral 36 to 60 Amps , 240 volt, 10 KA, complete all as specified and as directed by the Engineer-in-Charge. |
| 139 | Supply and fixing MCB single pole 5 to 30 Amps, 240 volts, 10 KA complete all as specified and as directed by the Engineer-in-Charge. |
| 140 | Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metres below normal ground level, connecting to the Galvanized iron earth wire 4.0 mm dia by means of bolts, nuts , check nuts and washers of galvanized iron and steel earth wire protected by provision of GI light grade pipe 15 mm bore including provision of concrete pit made from PCC ( 1:2:4) type B-1 (using 20 mm graded stone aggregate) with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4 Kg/Sqm) and frame of angle iron 40 x 40 x 6 mm and handle of 6 mm dia MS bar made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom, 1.50 metre long placed on top edge of earth plate, common salt & charcoal filling, with fixing arrangement , funnel, wire mesh and earth work in hard/dense soil , returning filling in and removal of surplus soil to a distance not exceeding 50 metres, all as per electrical plate No 5 of SSR 1991 Part-I and connecting to CBDB’s as specified or indicated including testing on completion . |
| 141 | M&L for point wiring in casing & caping including all fittings with 1.5 Sqmm size multi stranded FRLS copper conductor cable including clamps , screws gutti/plug etc PVC unsheathed cable into and including PVC box for mounting of switces and PVC insulated FRLS cable of size 1.5 Sqmm as earth continuity conductor for followings items Make: Havells/Polycab/KEI |
| 142 | All as per item Srl No. 141.00 here-in-before but for one light point or one fan point controlled by one, one switch complete all as specified and as directed by the Engineer-in-Charge.( Make - Finolex/ polycab/ Havells) |
| 143 | All as per item Srl No. 141.00 here-in-before but for one socket outlet 3 pin, 5 Amps on independent board.Make ( Make - Finolex/ polycab/ Havells) |
| 144 | All as per item Srl No. 141.00 here-in-before but for one socket outlet 3 pin, 5 Amps on same board. ( Make - Finolex/ polycab/ Havells) |
| 145 | All as per item Srl No. 141.00 here-in-before but for but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor (Multi-stranded) insulated and unsheathed electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 2.5 Sqmm copper stranded conductor as continuous earth wire connected to common dolly complete all as specified and as directed by Engineer-in-Charge.( Make - Finolex/ polycab/ Havells, |
| 146 | Supply and fixing socket 2 in 1, 5 Amp, flush type complete all as specified and as directed by Engr-in-charge.(Make :Anchor / SSK / Leader) |
| 147 | S&F of DB, Single Door, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, SPN 8 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof, suitable for incorporation of MCB’s and isolators etc and making all necessary connections, duly flush of wall surface, complete all as specified and directed by Engr-in-Charge. Make : Schneider Elect / Legrand / C&S / Hager |
| 148 | Supply and fixing MCB single pole and neutral 32 to 40 Amps , 240 volt, 10 KA, complete all as specified and as directed by the Engineer-in-Charge. |
| 149 | Supply and fixing LED flood light 100 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp with all accessories incl two run of 1.5 Sqmm Copper conductor cable from street light to junction box/OH conductor/Switch board/MCB fitting complete including required modification for fixing the in the bracket/GI light grade pipe etc all as specified and directed by Engineer in charge. Make; Bajaj or equivalent in Philips/Crompton greaves. |
| 150 | Taking down carefully alluminium / copper point wiring complete for light, fan, socket or power point etc with fittings fixtures such as ceiling rose, holders, electric fittings, switchs, sockets, aluminium conductor cable with and incl wooden batten or FR PVC conduit and its accessories such as wooden gutties, rawl plugs, GI screws, aluminium clips, nails etc complete and removing the material from site and making good the disturbed surface of wall / floor/ ceiling etc as original i.e. brick work, plastering, white washing, OBD etc as required, complete all as specified and directed. Please Enable Macros to View BoQ information |
| 151 | Taking down carefully alluminium / copper point wiring complete for light, fan, socket or power point etc with fittings fixtures such as ceiling rose, holders, electric fittings, switchs, sockets, aluminium conductor cable with and incl wooden batten or FR PVC conduit and its accessories such as wooden gutties, rawl plugs, GI screws, aluminium clips, nails etc complete and removing the material from site and making good the disturbed surface of wall / floor/ ceiling etc as original i.e. brick work, plastering, white washing, OBD etc as required, complete all as specified and directed. Please Enable Macros to View BoQ information |
