|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. |
| 2 | Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. All kinds of soil |
| 3 | \\"Providing and laying in position cement concrete of specified grade excluding the cost of centering, shuttering - All work up to plinth level: 1:2:4 (1 cement : 2 coarse sand (zone-III) drived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources). \\" |
| 4 | Centering and shuttering including strutting, propping etc. and removal of form for 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete |
| 5 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 6 | Centering and shuttering including strutting, propping etc. and removal of form for 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts |
| 7 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 8 | Centering and shuttering including strutting, propping etc. and removal of form for 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers. |
| 9 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 10 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level Mild steel and Medium Tensile steel bars. |
| 11 | Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-lll) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources. |
| 12 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift. |
| 13 | Random Rubble Masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand). |
| 14 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : 6.4.1 Cement mortar 1:4 (1 cement : 4 coarse sand). |
| 15 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. in Cement mortar 1:4 (1 cement : 4 coarse sand). |
| 16 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand). |
| 17 | Supplying, filling, spreading & leveling stone boulders of size range of 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. |
| 18 | Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. |
| 19 | Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm, in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer-in-charge. |
| 20 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 Fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: 19.30.1.1 with common burnt clay F.P.S. (non modular) bricks of class designation 7.5. |
| 21 | Making soak pit 2.5m diameter 3.0 m deep with a 45*45cm dry brick honeycomb shaft with bricks and S.W Drain pipe 100mm diameter, 108 m long complete as per standard design. |
| 22 | \\"CEMENT PLASTER IN TWO COATS 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge.\\" |
| 23 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rates includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. |
| 24 | Random Rubble Masonry with hard stone in superstructure above plinth level and upto floor five level, including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) at window sills, ceiling level and the like. 7.2.1 Cement mortar 1:6 (1 cement : 6 coarse sand). |
| 25 | Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, upto 25 metre height, above ground level, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40 mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge. |
| 26 | \\"Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineerin- charge (length of finished kerb edging shall be measured to calculate volume for payment). (Precast C.C. kerb stone shall be approved by Engineer incharge).\\" |
| 27 | Providing and fixing Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand). 11.26.1 25 mm Thick |
| 28 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 29 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by EngineerinCharge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 30 | Pointing on stone work with cement mortar 1:3 (1 cement : 3 fine sand) : 13.33.1 Flush/ Ruled pointing. |
| 31 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: 4.2.3 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 32 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 33 | Distempeering with 1st quality acylic distemper ( ready mixed) having VOC content less than 50gm/litre, of approved manufacturer and of required shade and color all complete to achieve even shade ands color New Work ( two or more coats) over and including water thinnable primming coat with cement primer having VOC content less than 50gm/litre. |
| 34 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : 21.1.1 For fixed portion 21.1.1.2 Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 35 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : 21.1.2 For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) 21.1.2.2 Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 36 | Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in- charge. 21.2.1 Pre-laminated particle board with decorative lamination on one side and balacing lamination on other sides. |
| 37 | Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: 9.95.1 125x75x4 mm |
| 38 | Providing & fixing aluminium sliding door bolt, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 9.96.1 300x16 mm |
| 39 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 9.97.1 300x10 mm |
| 40 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 9.100.1 125 mm |
| 41 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete : 9.101.1 Single rubber stopper |
| 42 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately) 9.1.2 Sal wood. |
| 43 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separetely, all complete as per direction of Engineer-in-charge. 9.5.1 Second class teak wood 9.5.1.1 35 mm thick shutters |
| 44 | Melamine polishing on wood work (one or more coat). |
| 45 | Providing and fixing G.I. chain link fabric fencing of required width in mesh size 25x25 mm made of G.I. wire of dia 3 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. |
| 46 | \\"Providing and fixing 18 mm thick ( Grenite ) gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. 8.2.2 Granite stone slab of colour black, Cherry/Ruby red 8.2.2.2 Area of slab over 0.50 sqm\\" |
| 47 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. 8.3.2 Granite work |
| 48 | Provision for providing and fixing of Electrical articles for supply of electricity.Plastic PVC Batten (RMT) |
| 49 | PVC Flexible Pipe (Each) |
| 50 | Junction Box for Plastic PVC Batten (Each) |
| 51 | Fan clip for ceilling for G (Each) |
| 52 | PVC Open Switch Board BOXES 12M (Each) |
| 53 | PVC Open Switch Board BOXES 8M (Each) |
| 54 | PVC Open Switch Board BOXES 4M (Each) |
| 55 | PVC Open Switch Board BOXES 2M (Each) |
| 56 | Suntech 12 Way SPN Metal White Double Door Distribution Board MCB Box (Each) |
| 57 | Polycab/Havells/Crompton or any similar brand PVC insulated 6 mm Single Core Flexible Copper Wires & Cables 90 Mtr. (Bundle) |
| 58 | Polycab/Havells/Crompton or any similar brand PVC insulated 2.5 mm Single Core Flexible Copper Wires & Cables 90 Mtr. (Bundle) |
| 59 | Polycab/Havells/Crompton or any similar brand PVC insulated 1.5 mm Single Core Flexible Copper Wires & Cables 90 Mtr. (Bundle) |
| 60 | Polycab/Havells/Crompton or any similar brand PVC insulated 1 mm Single Core Flexible Copper Wires & Cables 90 Mtr. (Bundle) |
| 61 | PVC Open Switch Board Boxes 12M Cover Plate (Each) |
| 62 | PVC Open Switch Board Boxes 8M Cover Plate (Each) |
| 63 | PVC Open Switch Board Boxes 4M Cover Plate (Each) |
| 64 | PVC Open Switch Board Boxes 2M Cover Plate (Each) |
| 65 | PVC Open Switch Board Boxes 1M Cover Plate (Each) |
| 66 | Polycarbonate Bulb Holder for wall (Each) |
| 67 | Havells 5 Step Fan Regulator - 2 Module (Each) |
| 68 | Havells 6A Five Pin Socket (Each) |
| 69 | Havells 6A One Way Switch-White (Each) |
| 70 | Havells 6A-16A Three Pin Combined Shutter Socket (Each) |
| 71 | Havells 16A One-Way Switch with indicator - White (Each) |
| 72 | Havells PVC Plastic 32A MCB DP C Curve - White (Each) |
| 73 | Havells 32A Single Pole MCB (Each) |
| 74 | Chipboard Screw with Saw Thread and Nylon Wood Dowel – White Zinc Plated – Flat Pozidriv Counter Sunk Head – Assorted Small Sizes – Pack of 258 pcs (Packet) |
| 75 | Havells 200mm Exhaust Fan (White) (Each) |
| 76 | LED Lights (Each) |
| 77 | Fan Box for Roof (Each) |
| 78 | Havells 3 Blades Ceilling Fan (Each) |
| 79 | Havells Fan Wall Mounted (Each) |
| 80 | Hitachi/Daikin/Voltas/LG/or Similar Brand Split Air Conditioner 1.5 Ton (Each) |
| 81 | Polycab/Havells/Crompton/or Similar brand PVC insulated 4 mm Single Core Flexible Copper Wires & Cables 90 Mtr. (Bundle) |
| 82 | Luminous/Similar brand Inverter with battery complete set (Each) |
| 83 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 Meter long etc. with charcoal/ coke and salt as required. |
| 84 | Crompton/Havells/or similar brand 2 HP water pump |
| 85 | Labour charges for fixing all electrical items (electrician + helper) complete job work |
| 86 | Transportation charges of material from market to site |
| 87 | Provision for Providing and Fixing of Sanitary Articles, Water Supply & Drainage.Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required: - (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer (Each) |
| 88 | Providing & fixing white vitreous china water less urinal of size 600 x 330 x 315 mm having antibacterial /germs free ceramic surface, fixed with cartridge having debris catcher and hygiene seal. (Each) |
| 89 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: 17.3.1 W.C. pan with ISI marked white solid (Each) |
| 90 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 18.8.3 25 mm nominal dia Pipes. (Metre) |
| 91 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 18.7.6 50 mm nominal dia Pipes. (Metre) |
| 92 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. (Each) |
| 93 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.17.28.2 Flexible pipe 17.28.2.2 40 mm dia (Each) |
| 94 | Providing and placing polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.[LTR] |
| 95 | Providing and fixing beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick [RMT] |
| 96 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 18.51.1 15 mm nominal bore [Each] |
| 97 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :18.49.1 15 mm nominal bore [Each] |
| 98 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 18.52.1 15 mm nominal bore [EACH] |
| 99 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore (Each) |
| 100 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 50 mm nominal bore (Each) |
| 101 | uPVC Waste Pipe 100 MM with necessary T, Corner and joints with chemical to fix and seal. (Mtr) |
| 102 | uPVC Waste Pipe 150 MM with necessary T, Corner and joints with chemical to fix and seal. (Mtr) |
| 103 | Screwed double flanged centrifugally cast (spun) C.I. Pipe of Class B Conforming to I.S. 1536, - 300 mm (RMT) |
| 104 | Screwed double flanged centrifugally cast (spun) C.I. Pipe of Class B Conforming to I.S. 1536, - 150 mm (RMT) |
| 105 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 17.10.2.1 Kitchen sink without drain board 610x510 mm bowl depth 200 mm. (Each) |
| 106 | Swan neck bib cock brass ISI Marked (Each) |
| 107 | PVC Coupler (Each) |
| 108 | PVC Elbow (Each) |
| 109 | PVC Tee (Each) |
| 110 | PVC End Cap (Each) |
| 111 | Solvent (100 Gram) |
| 112 | Ball Valve and Float Valve (Each) |
| 113 | P-trap (Each) |
| 114 | S-trap (Each) |
| 115 | PVC Bends & junctions (Each) |
| 116 | PVC Gully Trap (Each) |
| 117 | S.S Towel holder for washroom (Each) |
| 118 | Labour and Transportation charges for Non-DSR Items (Job) |
| 119 | Providing and Laying lime concrete with brick agg 20 to 25 mm gauge n/s & 50% lime mortar 1:1:1 (1 lime : 1 Surkhi : 1 C. Sand) including ramming, beating & top finishing etc complete including carriage of water & materials with in a lead upto 150 M approx. |
| 120 | Providing & Fixing 65 MM thick Red Sand Stone flooring over 20 MM thick bed with fine dressed on all exposed surface & fixed in position in lime surkhi mortar 1:1:1 (1 Lime : 1 Surkhi : 1 C.Sand) mixed with adhesive materials such as belgiri, gur, gum etc. including carriage of water & material with in a lead upto 70 M appx. |
| 121 | Provision for Recessed Pointing the Open Joints of R.R. Stone Masonry in Lime Surkhi Mortar 1:1:1 (1 Lime : 1 Surkhi : 1 Coarse Sand) mixed with adhesive materials such as belgiri, gur & gum with racking, cleaning & washing the joints including carriage of water & material with in a lead upto 70M approx. |
| 122 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 10.25.2 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 123 | Providing & Fixing chiseled 65 MM thick Red Sand Stone on stair of M.S. Iron frame with fastners/nut-bolt, araldite and matching pigment including cutting and finishing in required shape and size etc. complete |
| 124 | Providing and fixing horizontal chajja of stone 40 mm thick and upto 80 cm projection in cement mortar 1:4 (1 cement : 4 coarse sand), including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : 7.29.1 Red sand stone |
| 125 | Providing and fixing red sand stone brackets 55x22.5x45 cm sunk and moulded including providing and fixing with 4 Nos gun metal cramp 25x6 mm 30 cm long |
| 126 | Stone work, plain in copings, cornices, string courses and plinth courses, upto 75 mm thick in Cement Mortar 1:6 (1 cement : 6 coarse sand), including pointing with white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade. 7.32.1 Red Sand Stone |
| 127 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. 10.16.1 Hot finished welded type tubes |
| 128 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : 13.62.1 Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture Please Enable Macros to View BoQ information |
