|
| 1 | `SITC of Boom Barriers with up to 6 mtr Aluminium Extruded Telescopic (for length adjustment) Arm having red reflecting tapes and powder coated with white colour including Brushless DC Motor( up to 100 Watt) , drive unit for smooth operation and controller with push buttons (raise, lower and stop) with on-site speed and angle adjustments. The barrier should have reversal of boom on getting in touch with an obstruction for safety. The barrier should offer an opening time up to 2-6 sec for Open/Close with 100% Duty Cycle and MCBF of 12 million cycles and IP rating ofIP 65,CE Certification duly certified by NABL accredited labs` Warranty : 12 months Make : Neptune , Magnetic Autocontrol , Faac ) : With Prior Aproval Of Engineer In ChargeAccessories `SITC of IR Beam Photosensors for safety at all Boom Barrier systems including cabling/ducting required including the RXandTX modules operated on 24VDC and having potentio- free contacts of NO/NC. The Safety Sensors shall installed on MS Poles which shall be Powder coated having base plate to bolt down and provision for the RX/TX modules to fix on the same along with cables entry to terminate. The Sensors will have adjustable eye to align the IR beam within the range ofminimum 15mtrs etc complete as reqd.``SITC of LED Traffic Light, 24 V (DC)/230 V (AC) , Red and Green Colour with complete housing and IP65 protection for outdoor use, complete with mounting arrangement and pole``SITC of Interlocking Relay Circuit Panel for integrating Boom Barrier with Raise/Lower proximity limits to Automatically control Traffic Lights including providing Power Supply for Relay circuit of 12V, 1.5Amp rating along with Re-programming of the Controller for Boom Barrier integration with Raise/LowervCommands for traffic light functions, including cabling and ducting works``Supply of Receiver for barrier and remote (transmitter)for barrier UP/DN/STP`Installation/Labour Charges Civil Work including marking and construction of foundation on both sides as per requirement with prior approval of Engineer In Charge Electrical Work including providing and laying of wires, conduits, bends etc as per site requirement with prior approval of Engineer In charge |
| 2 | SITC of microprocessor based operation, digitally controlled voltage very low frequency door frame metal detector loaded with necessary software etc complete as required. Capable to detect all Metals, Zinc and Metal Alloys using single detection Prog to detect ferrous/non-ferrous metals at any location. Tested to IS: 14132: 1992. Continuous active detection capability, also quick reset capability after each detection. Uniform sensitivity throughout the door frame. Error Free reliable operation for various object speeds (slow walk speed). Minimum Nine zones, all zones overlapping to each other: Left Top, Centre Top, Right Top, Left Middle, Centre Middle, Right Middle, L eft Bottom, Centre Bottom, and Right Bottom. The Magnetic field of the DFMD Equipment harmless to magnetic media, electronics device supported by Test certificate from NABL (India) accredited labs. Should have IP rating 54.Warranty 12 months Make ( Motwane , Rapiscan , Garrette ) With Prior Aproval Of Engineer In Charge |
| 3 | Supply /Providing of Hand Held Metal Detector. Hand-Held Metal Detector (HHMD) shall be able to detect metal without being in direct contact with the object. The detector shall have an audible and visual alarm to indicate the detection of metal. HHMD shall be constructed to work on commonly available disposable or rechargeable Batteries. Quick and simple battery change shall be possible without using special tools. The unit shall have an independent portable battery charger. HHMD shall be equipped with an indicator to indicate battery status. Durability through shock-resistance (product can with stand drops or falls from upto 1m.) Conforms to the NIJ 0602.02 and the new NIJ 0602.03 Standards for metal detection. Conforms to the international standards currently applicable for safety, EMC and to the applicable CE regulations . Warranty 12 months Make ( Motwane , Rapiscan , Garrette ) With Prior Aproval Of Engineer In Charge |
| 4 | `SITC Of CONVEX MIRROR 1000 MM The body of the Convex Mirror should be made of finest Quality ABS Material and Poly-carbonate Sheet.Convex Mirror should be UV Stabilized with Orange / Red color.Convex Mirror should be in Circular round shape.Convex Mirror should be provided with installation kit (fixing brackets, nut bolts etc.).Convex Mirror should be installed with the help of clamp and Nut Bolts on MS Pole of 2 meter long and 75 mm dia . The pipe should be fixed to the ground in Foundation Concrete or square plate.OR Convex Mirror should be installed with the help of clamp, Nut Bolts and Wall Mounting Bracket on Wall.Warranty 12 months Make : Dark Eye , Avery Dennison , Safe Zone )With Prior Aproval Of Engineer In Charge |
| 5 | `SITC of SPRING POST 710 mm The body of Spring Post should be made of virgin special flexible material PU (Polyurethane).It should be quickly restore to its original state without doing any damage to spring post as well as vehicles in case of high speed collision by vehicles.Two bands of special Heat Transfer Tape of a minimum 75 mm width must be pasted through Heat Transfer Pasting Technology around the Spring Post which protects it from getting cut and tear and give better and clear visibility in night and provide very long life.It should keep excellent mechanical and chemical properties such as impact resistance and tensile strength thus withstands in very hot or very cold temperatures.It should have Ultra Violet stabilizer so that it is not discolored even after long time. It should be in three different parts: upper tubuler part should be made out of PU and two bottom parts should be made out of ABS (Astronitrilite Butadiene Styrene).All three parts should be assembled together with the help of three nuts and bolts to be used for installation too.Special epoxy bond is used to fix the Spring Post with road surface. The bond should be so strong that post will not be deviated by strong impact after installation.31 Springs/Rings should be molded in the Spring Post to ensure complete flexibility of the product.18 mm hole provided on top for fixing of hooks etc. Dimensions of the Spring Post should be: Length 710mm, upper dia 80mm and bottom dia is 210mm approx.Total weight of the Spring Post should be 1795 grams approx.Warranty 12 months Laboratory Testing for the following * The Spring Post should be tested for Material Identification for Poly Urethane (PU).* Its Tensile Strength at break should be 27.54 N/mm2 as per ASTM D 638.* Its Elongation at break should be 251.38% as per ASTM D 638s.* Its UV Weathering should be tested for 24 hours as per ASTM G 154.Make : Dark Eye , Avery Dennison , Safe Zone ) With Prior Aproval Of Engineer In Charge |
| 6 | `SITC of RUBBER CORNER GUARD Rubber Corner Guard should be made out of High Quality Natural Rubber material.Dual-layer body with ribs for better impact resistance.Rubber Corner Guard should be flexible enough to absorb impacts and protect corners of the walls against rubbing, scratching and brushing of vehicles.Base Color of the Rubber Corner Guard should be black.Rubber Corner Guard should be UV Stabilized so it doesn’t fade in sunlight.6 nos. reflective tapes in bright yellow colour should be pasted on the Corner Guard for maximum reflectivity.6 nos. screws and gitti should be used to installed the Rubber Corner Guard on Piller.Dimensions of the Rubber Corner should be* Length of the corner guard should be 1250 mm approx.* Size of the Reflective Tape should be: 170 × 90 mm approx.* Thickness from side should be: 11 mm approx.* Thickness from centre should be: 10 mm approx.* Weight of the Rubber Corner Guard should be 4 kg approx. Warranty 12 months Make : Dark Eye , Avery Dennison , Safe Zone ) With Prior Aproval Of Engineer In Charge |
| 7 | SITC Of Speed Breaker resistent to severe impacts and harsh weather conditions with interlocking sub units to make make it bind perfectly into a one firm bump pre-colored material (Black/Yellow) and UV stabilized to keep them perpetually colorful, studded with reflectors on either side to offer clearly visibility to the motorists during night hours.Speed Bumps shall be designed so dynamically and compact that it can bear maximum load on it.The body of the Speed Bump shall be made of High Density Poly Ethylene (HDPE) plastic material.Four highly reflective reflectors molded in PMMA material shall be welded with PE base plate through ultrasonic welding process and then fixed on the speed bump so that dust and water cannot touch the reflector’s inside area and thus it maintains its reflectivity for a long time.The top surface of the speed breaker shall be flat in order to support the vehicles from jerking or skidding.6 Nos. Nails of 4” shall be used per pc for installation on road.The Speed Bump shall be tested for Material Identification for High Density Polyethylene (HDPE) as per ASTM D3418. Its UV Exposure shall be tested for 24 hours as per ASTM G154.Compressive strength of the Speed Bump shall be 214 Ton as per ASTM D 4280-23.Warranty 12 monthsHeight 50 mm Length : 500 mm Width 365 mm Weight 5040 gms approx per meter Material :HDPE Make : Dark Eye , Avery Dennison , Safe Zone ) With Prior Aproval Of Engineer In Charge |
| 8 | SITC of Self-Contained Rechargeable Emergency Maintained LED Slim Exit Exit/ Fire Exit,PEL LED E/M(S), Guide Lights/ Safety Lights /Egress Light/SS,DS mirror optic made up of uniformly extruded Aluminium Alloy : Battery backup GP for 3hrs: with 3W multiple LED’s: IP 20: Single / Double Sided 8mm : 16 to 24 hrs Recharging Period: Confirms to IS - 10322 GP Epoxy polyester powder coating, White in colour: Convey Warranty 12 months Make (Prolite, Insta, Evaclite, Ventilux ) With Prior Aproval Of Engineer In Charge |
| 9 | SITC of Self Contained Rechargeable Maintained Decorative Exit/ Fire Exit, Guide Lights/ Safety Lights /Egress Light PAL LED EM Glow Period for 3hrs IP 20 Single Sided (Surface Type) IP 20 Battery Duration plus 10% 16 to 24 hrs Recharging Period IS - 10322 GP Epoxy polyester powder coating, White in colour Multiple LEDs Convey Warranty 12 months Make (Prolite, Insta, Evaclite, Ventilux ) With Prior Aproval Of Engineer In Charge |
| 10 | `SITC of Self Maintain Signages 1 mm thick Rigid Sheet ARS 10000 Dark Glow Photoluminescent with Strong GP Self Adhesive , Working temperature -20 to plus 80’C Life, Class - A / DIN 67510 Part 2 / 60 Minutes / ) 700 mcdl with High Glow Intensity Certified By Government Of India Lab For A Glow Period ) 24 Hrs DRDO, DGP and ARAI, IS 9457-2005 ,IS 12349 Warranty 12 months Make (Prolite, Insta, Evaclite, Ventilux ) With Prior Aproval Of Engineer In Charge 100 X 300 mm |
| 11 | `SITC of Self Maintain Signages 1 mm thick Rigid Sheet ARS 10000 Dark Glow Photoluminescent with Strong GP Self Adhesive , Working temperature -20 to plus 80’C Life, Class - A / DIN 67510 Part 2 / 60 Minutes / ) 700 mcdl with High Glow Intensity Certified By Government Of India Lab For A Glow Period ) 24 Hrs DRDO, DGP and ARAI, IS 9457-2005 ,IS 12349 Warranty 12 months Make (Prolite, Insta, Evaclite, Ventilux ) With Prior Aproval Of Engineer In Charge 200 X 200 mm |
| 12 | `SITC of Self Maintain Signages 1 mm thick Rigid Sheet ARS 10000 Dark Glow Photoluminescent with Strong GP Self Adhesive , Working temperature -20 to plus 80’C Life, Class - A / DIN 67510 Part 2 / 60 Minutes / ) 700 mcdl with High Glow Intensity Certified By Government Of India Lab For A Glow Period ) 24 Hrs DRDO, DGP and ARAI, IS 9457-2005 ,IS 12349 Warranty 12 months Make (Prolite, Insta, Evaclite, Ventilux ) With Prior Aproval Of Engineer In Charge 300 X 300 mm |
| 13 | `SITC of Self Maintain Signages 1 mm thick Rigid Sheet ARS 10000 Dark Glow Photoluminescent with Strong GP Self Adhesive , Working temperature -20 to plus 80’C Life, Class - A / DIN 67510 Part 2 / 60 Minutes / ) 700 mcdl with High Glow Intensity Certified By Government Of India Lab For A Glow Period ) 24 Hrs DRDO, DGP and ARAI, IS 9457-2005 ,IS 12349 Warranty 12 months Make (Prolite, Insta, Evaclite, Ventilux ) With Prior Aproval Of Engineer In Charge 250 X 200 mm |
| 14 | `SITC of Self Maintain Signages 1 mm thick Rigid Sheet ARS 10000 Dark Glow Photoluminescent with Strong GP Self Adhesive , Working temperature -20 to plus 80’C Life, Class - A / DIN 67510 Part 2 / 60 Minutes / ) 700 mcdl with High Glow Intensity Certified By Government Of India Lab For A Glow Period ) 24 Hrs DRDO, DGP and ARAI, IS 9457-2005 ,IS 12349 Warranty 12 months Make (Prolite, Insta, Evaclite, Ventilux ) With Prior Aproval Of Engineer In Charge A3(297X420) Evacuation Plan |
| 15 | Supply of AUTOGLO Photoreflective in 1 mm thick Aluminium Sheet APRA 10000(R) Dark Glow Photoreflective with Strong GP Self Adhesive , Working temperature -40’C to 120’C Life, Class - A / DIN 67510 Part 2 / 60 Minutes / ) 700 mcdl with High Glow Intensity Certified By Government Of India Lab For A Glow Period ) 24 Hrs DRDO, Life)20-30years for indoor and life)5-6 years Outdoor ,DGP and ARAI, IS 9457-2005 ,IS 12349 Warranty 12 months Make(Prolite, Insta, Evaclite, Ventilux ) With Prior Aproval Of Engineer In Charge 100 X 300 mm |
| 16 | Supply of AUTOGLO Photoreflective in 1 mm thick Aluminium Sheet APRA 10000(R) Dark Glow Photoreflective with Strong GP Self Adhesive , Working temperature -40’C to 120’C Life, Class - A / DIN 67510 Part 2 / 60 Minutes / ) 700 mcdl with High Glow Intensity Certified By Government Of India Lab For A Glow Period ) 24 Hrs DRDO, Life)20-30years for indoor and life)5-6 years Outdoor ,DGP and ARAI, IS 9457-2005 ,IS 12349 Warranty 12 months Make(Prolite, Insta, Evaclite, Ventilux ) With Prior Aproval Of Engineer In Charge 200 X 200 mm |
| 17 | Supply of AUTOGLO Photoreflective in 1 mm thick Aluminium Sheet APRA 10000(R) Dark Glow Photoreflective with Strong GP Self Adhesive , Working temperature -40’C to 120’C Life, Class - A / DIN 67510 Part 2 / 60 Minutes / ) 700 mcdl with High Glow Intensity Certified By Government Of India Lab For A Glow Period ) 24 Hrs DRDO, Life)20-30years for indoor and life)5-6 years Outdoor ,DGP and ARAI, IS 9457-2005 ,IS 12349 Warranty 12 months Make(Prolite, Insta, Evaclite, Ventilux ) With Prior Aproval Of Engineer In Charge 300 X 300 mm |
| 18 | Providing and Fixing Of Metal Road Wheel Barrier(size6.50 feet x 5.50 feet x 1.67 feet) fabricated with pipe (40mmx40mm) ,angle (25mmx25mm) ,strip (25mm) , Jali with 25 mmx25mm square . The structure shall be movable with low sound castor wheels . The barrier shall be fixed with 18 guage MS sheet of size 4 x 2.5 feet on the secured side having University Logo and welcome message duly printed on retro reflective sheet and solar blinker in round shape .Barrier shall be duly painted in yellow colour with prior red oxide treatment for smooth finish .Weight of the entire barrier structure shall be approximately 100kg per unit . Warranty 12 months Make : (ZBE , Neptune , Dark Eye ) With Prior Aproval Of Engineer In Charge Please Enable Macros to View BoQ information |
