|
| 1 | Surface dressing n exc15 cm deep and getting out any type of soil complete all as specified and directed. |
| 2 | Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation .etc in soft/loose soil complete all as specified and directed. |
| 3 | M&L for plain cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation, filling & mass concrete, sub base complete all as specified and directed. |
| 4 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick with soft/loose soil etc complete all as specified and directed. |
| 5 | Demolition of brickwork built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed. |
| 6 | Demolition of Reinforced concrete in suspended slab, beam etc in cement mortar complete all as specified and directed. |
| 7 | Demolition of unreinforced concrete in ground floors and paving n.exc. 15 cm thickness below or above ground level complete all as specified and directed. |
| 8 | Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed. |
| 9 | M&L for providing reinforced cement concrete (M-25) Design Mix using 20 mm graded stone aggregates as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.. |
| 10 | M&L for providing reinforced cement concrete (M-25) Design Mix using 20 mm graded stone aggregates as in Column, pillar, piers, posts and struts complete all as specified and directed. |
| 11 | M&L for providing reinforced cement concrete (M-25) Design Mix using 20 mm graded stone aggregates as in Slab supported on walls, beams and columns in floors, roofs, complete all as specified and directed. |
| 12 | M&L for providing reinforced cement concrete (M-25) Design Mix using 20 mm graded stone aggregates as in Roof beam, cantilever, bressummer, lintel over 1.5 span complete all as specified. |
| 13 | M&L for providing reinforced cement concrete (M-25) Design Mix using 20 mm graded stone aggregates as in Chajja complete all as specified and directed. |
| 14 | M&L formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter (rough finished surface) complete all as specified and directed. |
| 15 | M&L formwork to sides of pillars, posts, struts, piers, columns and stanchions (square/rectangular/ polygonal) rough finished surface complete all as specified and directed. |
| 16 | M&L formwork to soffits of suspended slab such as roof slabs, floor slabs, landings and similar work not exceeding 200 mm thick rough finished in flat surface complete all as specified and directed. |
| 17 | M&L formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors in rough finished flat surfaces and etc complete all as specified and directed. |
| 18 | M&L formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete rail ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizon tal or sloping and similar work exc 10cm but n exc 20cm wide (rough finished surface) complete all as specified and directed. |
| 19 | M&L for TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending for hooping for columns, hooking ends and binding with and including steel wire (annealed) not less than 0.9 mm dia or securing with clips etc complete all as specified and directed. |
| 20 | All as per ser item No.19 above, but 6 mm dia to 8 mm dia complete all as specified and directed. |
| 21 | All as per ser item No. 19 here-in-before, but 5 mm dia & over upto & including 10 mm dia in stirrups, spacers and binders, complete all as specified and directed. |
| 22 | M&L for brickwork with fly ash old size bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed. |
| 23 | M&L for Brick work with flyash bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:6 complete all as specified and directed. |
| 24 | M&L for rendering 15 mm thick in cement mortar (1:6) on brick work or concrete surfaces finished even and fair (without using extra cement) complete all as specified and directed. |
| 25 | M&L for 15 mm thick plastering in cement mortar (1:4) on brick or concrete surfaces including rendering on fins, fascias, chajja, parapets etc and finishing the surfaces even and fair (without using extra cement), top layer shall be with WPC as per manufacturer's instruction and complete all as specified and directed. Note: WPC shall be measured and paid separately. |
| 26 | M&L rendering 10mm thick in cement mortar (1:3) as in ceilings finished even and fair (without using extra cement) complete all as specified and directed. |
| 27 | Supplied only Liquid water proofing compound complete all as specified and directed. |
| 28 | M&L for preparation of new internal plaster surfaces applying two coats of oil bound distemper over a coat of alkhali resistant primer over a coat of wall care putty 1.5 mm thick complete all as specified and directed. |
| 29 | M & L for preparation of new plastered surfaces of wall and applying two coats of exterior weather coat over a coat of weather coat exterior primer for camouflage design incl necessary scaffolding complete all as specified and directed. |
| 30 | M&L for Preparation of newly plastered surfaces of ceiling and applying three coats of white wash on ceiling surfaces complete all as specified and directed. |
| 31 | M&L for complete removal of existing treatment of internal wall surfaces and applying 1.5mm thick Birla or equivalent wall putty to old plastered surface and applying two coats of oil bound distemper complete all as specified and directed. |
| 32 | M&L for Hardcore (broken stone or boulders) of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed. |
| 33 | M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed. |
| 34 | M&L for 75 mm thick cement concrete (1:4:8) type D-2 (using 40 mm graded stone aggregates) as in sub base of flooring etc complete all as specified and directed. |
| 35 | M&L for Machine cut kota stone slab flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete, in floors including screed bed or bedding layer of mortar 20 mm thick in CM 1:6 complete all as specified and directed. |
| 36 | All as per Sl item No 35 above, but in skirting over 10mm thick backing coat in CM 1:4 complete all as specified and directed. |
| 37 | M&L rendering 10mm thick plastering on fair faces of concrete surface in CM 1 : 4 with water proofing compound @ 2% by weight of cement even and fair surface complete all as specified and directed. Note:- Liquid water proofing compound shall be measured and paid separately. |
| 38 | M & L for applying evenly a tack coat of industrial bitumen 85/25 @ 1.2 kg/Sqm including cleaning surface complete all as specified and directed. |
| 39 | M&L for 3mm thick APP modified prefabricated membrane weight not less than 3.0 Kg/Sqm water proof membrane reinforced with non-wooven polyster (wt. not less than 150 gms/sqm) land on primed surface by forced water proofing membrane with 10cm longitudinal and horizontaling over lapping and joints finally thermo-fused with LPG flames laid over a tack coat of industrial coat of primer as per manufacturer's instructions of APP modified membrane sheet complete all as specified and directed. |
| 40 | M&L 75mm thick PCC (1:3:6) type C-2 (Using 40mm graded stone aggregate) as in plinth protection, laid in panels, finished the top surfaces even and fair without using extra cement complete all as specified and directed. |
| 41 | M&L powder coated aluminium sliding window shutters with frames (consisting of 02 Nos glazed shutters and 01 No gauze shutter) Series -D (25mm), 3 track sliding shutters, duly fitted with neoprene beading, glazing clips, locking device, heat absorbing glass 5.5 mm nominal thickness in glazed shutters, stainless steel wire mesh of 0.254mm nominal dia of wire and 0.95 mm average width of aperture in gauzed shutter and powder coated aluminium grill 4mm dia, 75 x 75mm aperture fixed with standard aluminium beading fixed in outer portion of the chowkat complete all as specified and directed. |
| 42 | M&L fabricated powder coated anodized aluminium grill of size 75x75 mm, using 6mm dia bars fixed to outer portion of chowkhat using U/V section runners complete all as specified and directed. |
| 43 | M&L 1.25 mm thick pressed steel frame of size 105X 60 mm for door with one ore more rebate including necessary fixing lugs, stainless steel hinge, locks strike plate etc complete all as specified and directed. |
| 44 | M&L factory made 35mm thick flush shutters solid core construction with block board core and plywood face panel commercial type on both faces complete all as specified and directed. |
| 45 | M&L for PCC type C1,1:3:6 (using 20 mm graded aggregate) for holdfast blocks complete all as specified and directed. |
| 46 | M & L for Preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel painting over a coat of pink primer complete all as specified and directed. |
| 47 | M & L for preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide, primer exceeding 10cm in width or girth not otherwise described complete all as specified and directed. |
| 48 | S&F MS butt hinge medium weight cold rolled 100mm size complete all as specified and directed. |
| 49 | S&F 200mm long aluminium anodised tower bolts of extruded section and fixed complete all as specified and directed. |
| 50 | S&F 300mm long aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixed clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast- aluminium alloy and fixed complete all as specified and directed. |
| 51 | S&F 150mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed. |
| 52 | M&L Solid PVC Door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube, supplying and fixing in opening as per specification and drawing complete all as specified and directed. |
| 53 | M&L factory made solid panel PVC door shutter, 30 mm thick (style) consisting of frame made out of MS tubes for top and bottom rails, MS frames shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame, welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site with three nos of MS higes medium grade complete all as specified and directed. |
| 54 | M&L Powder coated aluminium (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed. |
| 55 | M&L powder coated Anodised aluminium window & ventilator shutters side hung type without sash bar, aluminium sections weighing 0.55 kg/m including necessary joining, cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as hinge type B-21 100 mm long (2 nos) suitable handle 1 No complete all as specified and directed. |
| 56 | M&L 4 mm thick one side frosted sheet glass ordinary quality and glazing in square n.exc 0.5sqm in each pane fixed with neopune rubber gasket in aluminium frame complete all as specified and directed. |
| 57 | M & L for coloured non skid ceramic tiles 7 to 8 mm thick (square/rectangular) in section exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors laid over and including 15mm thick screed bed in CM 1:6 etc set and jointed in neat cement slurry and pointed in white or coloured cemnt to match complete all as specified and directed. |
| 58 | M&L for Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick CM (1:4) backing coat complete all as specified and directed. |
| 59 | Dismantling ceiling board (fiber, pulp insulation) or insulation board/slabs etc including grid work/wooden or aluminium frame works, cover fillet etc complete all as specified and directed. |
| 60 | M&L for Powder coated galvanised iron snap grid frame work of size 600 x 600 mm for false ceiling comprising of Main runner 'T' section of size 38mm x 24mm x 0.40mm thickness, Cross 'T' of size 29mm x 24mm x 0.3mm thickness and wall angle of size 24mm x 24mm x 0.43mm thick suspended with 4mm dia GI wire from purlin @ 1.20m c/c and fixed with 4mm thick designer ceiling boards complete all as specified and directed. |
| 61 | M&L of steel work as in tubular trusses including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS – 1161 – 1979 grade St – 240 complete all as specified and directed. |
| 62 | Dismantling AC/ galvalume sheet of any thickness as in roof covering complete all as specified and directed. |
| 63 | M&L Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed. |
| 64 | M&L Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 65 | M&L 20mm bore GI water tubing medium grade laid in floors or fixed in wall with GI fittings complete all as specified and directed. |
| 66 | M&L15mm bore GI water tubing medium grade laid in floors or fixed in wall with GI fittings complete all as specified and directed. |
| 67 | M&L PVC (SWR) 110mm dia single socketed in any length with rubber ring joints laid in trenches or in floor complete all as specified and directed. |
| 68 | S&F PVC (SWR) 110mm dia bend in any radius complete all as specified and directed. |
| 69 | M&L of PVC (SWR) 75 mm dia pipe complete all as specified and directed. |
| 70 | S&F for 600mm x 450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 71 | M & L for 75 mm dia PVC (SWR) pipe single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed. |
| 72 | S & F 75mm bore PVC (SWR) bend any radius complete all as specified and directed. |
| 73 | M & L Viterous china ware wash down water closet pan (EWC), pedestal pattern coloured including plastic WC seat black closed pattern eith flat bottom and cover and steel chromium plated of aluminised hinging device, complete fitting complete all as specified and directed. |
| 74 | S&F 15mm bore bib tap cast copper alloy with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. |
| 75 | S&F 15mm bore Pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed. |
| 76 | S&F 15mm bore angle stop cock, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe complete all as specified and directed. |
| 77 | S&F PVC low level flushing cistern 10 ltr capacity syphonic action type white body with MS bracket , inlet ball valve, float handle and flush pipe (for EWC or WC) etc complete all as specified and directed. |
| 78 | S&F for PVC Connection pipe 15mm size with PTMT nuts of length 450 mm complete all as specified and directed. |
| 79 | S&F vitreous china wash basin, size 550 x 400mm white including brackets, and waste coupling & pipe of 32mm dia, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other and fixed complete all as specified and directed. |
| 80 | S&F stainless steel sink, made out of 1.00mm thick sheet for kitchen or laboratory, with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantiliver brackets and connecting union to pipe, overall size 915mm x 460mm with bowl size 410mm x 330mm x 160mm complete all as specified and directed. |
| 81 | S&F for vitreous china urinal, half stall type, white including flushing cistern, flush pipe and waste pipe. CP waste coupling complete all as specified and directed. |
| 82 | S & F for Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and directed. |
| 83 | S&F toilet paper holder, coloured vitreous china, box type fixed in wall complete all as specified and directed. |
| 84 | S&F soap dish, vitreous china white, aprox size 160 X 160 X 90 mm. fixed to plugs with chromium plated brass screws complete all as specified and directed. |
| 85 | S&F CP towel rail 600mm long with brackets, aluminium anodised 20mm dia complete all as specified and directed. |
| 86 | S&F CP grating 100mm dia PTMT with waste hole complete all as specified and directed. |
| 87 | S&F CP Health Faucet suitable for 15 mm dia pipe with 1.25 m long flexible tube and ABS wall hook including making connection fixed in position complete all as specified and directed. |
| 88 | S&F PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and directed. |
| 89 | M & L for precast cement concrete1:2:4 type B-1 using 20 mm stone aggregate as in manhole cover slabs round square or rectangular in shape and set in CM 1:4 complete all as specified and directed. |
| 90 | M&L for PCC 1:3:6 type C-2 (40mm grade stone aggregate) as in bed to 110 mm dia SGSW /PVC pipes including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed. |
| 91 | M&L for PCC 1:2:4 type B-0 using 40mm aggregate as in surface channel/ benching in manhole etc complete all as specified and directed. |
| 92 | Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing, benching for and forming branch channel(1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required complete all as specified and directed. |
| 93 | S&F rotational moulded polyethylene 500 Ltrs Capacity water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position in SSR Part-I including ball brass valve, with polyethylene float and fly nut complete screwed down for iron pipe of 20 mm dia complete all as specified and directed. |
| 94 | Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, in any type of soil complete all as specified and directed. |
| 95 | M&L PCC 1:2:4 type B-2 using 40mm graded aggregate as in foundations of pillar or post filling and mass concrete complete all as specified and directed. |
| 96 | M&L Steel work in tubular/square tube trusses/purlins including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed. |
| 97 | M&L Steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe 410 -W (Gde- E- 250) quality- B complete all as specified and directed. |
| 98 | M&L Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required hooks (stay) heavy for large gates, hook and pintle hinges large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed. |
| 99 | M&L for preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 100 | M&L Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 101 | Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in any type of soil complete all as specified and directed. |
| 102 | M & L for broken stone or boulders in Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed. |
| 103 | M & L for 75 mm thick Plain Cement concrete of type D-2, 1:4:8 (40 mm graded aggregate) in subbase etc complete all as specified and directed. |
| 104 | M&L of sand filling to receive interlocking tiles including Spreading & levelling in layers n.exc. 25cm thick complete all as specified and directed. |
| 105 | M&L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade With grey cement and pigment complete all as specified and directed. |
| 106 | Surface Excavation not exc 30 cm deep and averaging 15 cm deep and getting out soft/loose soil complete all as specified and directed. |
| 107 | M&L for Hardcore (broken stone or boulders) of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed. |
| 108 | M & L for sand cushioning to receive interlocking tiles incl spreading, levelling in layers complete all as specified and directed. |
| 109 | M&L for 100 mm thick PCC (1:4:8) type D2 using 40 mm graded stone aggregate as in sub base etc complete all as specified and directed. |
| 110 | M & L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade With Grey Cement and pigment complete all as specified and directed. |
| 111 | Rolling and consolidating formation surface in cutting with power roller 8 to 10 ton complete all as specified and directed. |
| 112 | Laying and compacting 150 mm thick (compacted thickness) Granular Sub Base Course (GSB) grading as per Grade I as specified Table 400-1 of MaRTH specifications for Road and Bridge works, 2013, in a single layer over compacted subgrade with natura sand, crushed gravel, crushed stone, crushed slag or combination thereof as per the grading required The materials are mechanically mixed, spread and levelling on the subgrade by using motor grader of adequate capacity, and rolling with vibratory roller of capacity 80-1 00 KN static weight for achieving required compaction density of at least 98% of the Maximum Dry Density. Consolidating to required gradient and camber complete all as specified and directed. |
| 113 | Removing excavated material n. exc.50 m and depositing where directed at level n. exc. 1.5m above the starting point complete all as specified and directed. |
| 114 | M&L for cement concrete type B-1, 1:2:4 (20mm graded stone aggregate) as in cills, steps; seismic , parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, etc and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed. |
| 115 | M&L for RCC NP3 150 mm diameter Pipes laid on 150 mm thick PCC (1:4:8) bed with excavation in any type of soil upto depth 1.65m, including manholes/drop manhole of standard size made of Brick masonry/ RCC/Precast RCC with SFRC ventilating cover and frame. Includes all items and activities to execute and make sewer line functional complete all as specified and directed. |
| 116 | M&L for LLDPE septic tank designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, Vent shaft, connection etc., complete for 25 Users with upflow filter complete all as specified and directed. |
| 117 | M&L for Soakage wells of effective depth 3.6m x 3.00m; excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size complete all as specified and directed. |
| 118 | Taking down carefully copper/aluminium point wiring complete (light, fan, plug point & power complete alongwith fittings (switches, ceiling roses, tube light fittings, bulk head fitting regulator, sockets , removing materials to store and offering credit & making good of disturb surfaces of wall/floors etc complete all as specified and directed. |
| 119 | M& L for Point wiring with 1.5 Sqmm (22/0.30mm) PVC insulated and unsheathed multistranded copper conductor cable, 1100 volts grade, ISI marked, FR type drawn through and including PVC casing caping/ PVC Conduit (ISI marked) and its accessories such as Tee, elbow, jointer, elbow corner etc. fixed on surface of walls, columns/ beams alongwith 1.5 Sqmm (nominal area) copper conductor cable (multistranded) PVC insulated and unsheathed as earth wire connected to common earth dolly at one end and metallic bodies of luminaire/ fan at other end including PVC folding boards with sunmica top for mounting switches, sockets, fan Regulators, accessories etc as per site requirement complete all as specified and directed. for the following:- (a) One light point or one fan point controlled by one switch with cables 1.5 sq. mm size Note:- Unit rate include for cutting chases for conduits and sinking for boxes and making good to wall, floors etc. |
| 120 | All as per ser item No.119 above, here in before but for One 5 Amp 5 pin socket outlet point on same board with other switches including earth wire complete all as specified and directed. |
| 121 | All as per ser item No. 119 here in before, but for One 5 Amp 5 pin socket outlet point on independent board complete all as specified and directed. |
| 122 | All as per ser item No. 119 here in before, but with 4.0 Sqmm (36/0.30mm) PVC copper stranded cable FRLS type for one 15 Amp 5 pin socket outlet point including PVC cable 4 Sqmm FRLS type copper stranded conductor as earth wire as specified & connected to common earth & earth terminals including boards for mounting purposes complete all as specified and directed. |
| 123 | S&F in replacement switch piano flush button 5 Amp single pole one way 230 volts white finish complete all as specified and directed. |
| 124 | S&F in replacement of socket outlet flush type 5 pin 5 Amp multipurpose 230 volts single pole one way suitable for 3 pin/2pin 5 Amp plug top white/ivory finish complete all as specified and directed. |
| 125 | S&F in replacement switch socket combination flush type 5 pin 5 Amp multipurpose 230 volts single pole one way suitable for 3 pin/2pin 5 Amp plug top white/ivory finish complete all as specified and directed. |
| 126 | S&F in replacement of switch socket combination multipurpose flush type 2 in 1 type (3 and 5 pin) 5/15 Amps, 230V, AC complete all as specified and directed. |
| 127 | S&F in replacement energy efficient Street/ Roadway/Building Security Luminaire LED fitting upto 35 Watt 230 V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete, including brackets and all accessories needed to fixed to the wall or pole all as per site requirement and complete all as specified and directed. |
| 128 | S&F ceiling fan complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed. |
| 129 | S&F exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers including suitable hole in existing wall complete as per site requirement and complete all as specified and directed. |
| 130 | S&F LED light fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. |
| 131 | S&F in replacement LED panel light 36 watt efficient LED recessed luminaire 2 ft x 2 ft (>100 Lumen/Watt) to enhance the delight of occupants with comfortable experience through its classic design & glare free soft illumination for armstrong/ grid ceiling or similar ceiling mounting system with concealed complete prewied complete as per site requirement complete all as specified and directed. Note : Rate for removing of existing unserviceable old luminaire is deem to be included in this item rates. |
| 132 | S&F in replacement stepped type electronic fan regulator Socket type on the existing phenolic laminated sheet etc complete all as specified and directed. |
| 133 | S&F in replacement ceiling rose surface PVC 50mm dia 3 terminals including PVC mounting block white/ivory finish complete all as specified and directed. |
| 134 | M&L in replacement of submain wiring with two single core PVC insulated unsheathed, multistranded flexible copper conductor 1100Volts grade, FRLS type, cables 10 Sqmm drawn through in and including rigid PVC heavy duty concealed conduits including 6 Sqmm 1100Volts grade, FRLS type, PVC insulated unsheathed multi stranded flexible copper conductor cable as continuous earth wire and connecting to common earth terminals complete all as specified and directed. Note:- (i) Two runs of cables and one run of continuous earthing cable drawn in conduit/ casing and caping will be measured as one length of sub main with colour code Red Black and Green. (ii) PVC conduit / casing caping and its accessories is deem to be included in this item rates. (iii) Unit rate include for cutting chases for conduits and sinking for boxes and making good to wall, floors etc. |
| 135 | S&F in replacement TPN distribution board 415volts sheet metal enclosure double door shutter type factory made fixed flush with wall or outside on wall surface suitable for mounting isolators & MCB's 220volts, 200 Amp rated bus bar with front openable cover suitable for TPN 4 ways MCB complete all as specified and directed. |
| 136 | S&F in replacement SPN distribution board sheet metal enclosure double door shutter type factory made fixed flush with wall or outside on wall surface suitable for mounting isolators & MCB's 240volts, 200 Amp rated bus bar with front openable cover suitable for SP & N 8 ways complete all as specified and directed. |
| 137 | S&F in replacement MCB SPN/DP 32 Amp rating 240V, 10KA 'C' curve complete with connection testing and commissioning complete all as specified and directed. |
| 138 | S&F in replacement MCB SP 6 to 32 Amp rating 240V, 10KA 'C' curve complete with connection testing and commissioning complete all as specified and directed. |
| 139 | S&F in replacement MCB TPN 16 to 32 Amp rating 415V, 10KA 'B' curve complete with connection testing and commissioning complete all as specified and directed. |
| 140 | M&L in replacement of Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thickness buried directly in ground (earth pit not less than 2.25mtr deep below normal ground level) with top edge of earth plate not less than 1.5 mtr below normal ground level connected to and incl galvanised earth lead wire of 4.00mm dia by means of nuts & bolts, check nuts and washers of galvanised incl PCC pit of 1:2:4 type B-1, cover reinforced with XPM weight not less than 4 Kg/Sqm and 6mm dia bar handle, earth pit angle iron frame of size 25mm x 25mm, excavation and earth work in any type of soil, charcoal dust, salt, light grade GI watering pipe 20mm dia with funnel and wire -mesh and medium grade GI protection pipe of 15mm bore from top edge of earth plate upto main distribution board complete all to as shown in electrical plate No 3 of MES Sch 2009 (Part I) connected main switch board complete all as specified and directed. |
| 141 | NOTES :-1. The amount of schedule of credit shall be deducted from the total of this BOQ for arriving at contract sum. Please Enable Macros to View BoQ information |
