|
| 1 | Demolition of un-reinforced cement concrete of any description in any position including sunken portion not otherwise specifically provided for complete all as specified and directed. |
| 2 | Material and labour water proofing treatment to SUNKEN PORTION and adjoining walls of kitchen, WC, Bath & Toilet, etc, as follows, complete all as specified & directed :- (a) 15 mm thick plaster in cement mortar (1:3) mixed with WP compound as per manufacturer's instructions shall be provided on sunken portion after roughening of surfaces. (b) Apply cement slurry to the surface @ 0.488 kg /Sqm of cement mixed with Acrylic based polymer modified cementious composite compound @ 0.253 kg/Sqm and the surface will be allowed to air cure for 4 hours.(c) Apply another layer of cement slurry @ 0.242 kg/Sq. m of cement mixed with Acrylic based polymer modified cementious composite compound @ 0.126 Kg/Sq. m and the surface will be allowed to air cure for 4 hours.(d) Pond curing of sunken portion for minimum of 48 hours.(e) Pasting 200 micron thick polythene film with approved adhesive.(f) Joints/ traps /WC /soil pipes shall be properly sealed with approved sealing compound. |
| 3 | Steel water tubes, 40mm bore medium grade galvanized as in spout for sunken floor, fixed in wall inside and fixed with wire netting and external beveled edge at 45 degree, including taking down existing steel tubing of any size froom floors, ceiling, walls complete all as specified and directed |
| 4 | Plain cement concrete 1:7:12 type F-2 using 40mm graded brick coarse aggregate as in sunken floor filling and mass concrete complete all as specified & directed. |
| 5 | M&L for PCC 1:2:4 type B-0 (12.5 mm graded aggregate) mixed with water proofing compound as levelling course on roof or sunken slab all as specified and directed. |
| 6 | Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviveable tiles to store and rubbish off the premises complete all as specified and directed |
| 7 | Glazed coloured ceramic tiles in vertical surface 300mm x 450mm x 7mm thick , set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed. |
| 8 | Non skid, first quality ceramic coloured tiles, 7 to 8 mm thick (square/ rectangular) area or each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed. |
| 9 | 75mm thick Plain cement concrete 1:3:6 type B-0 using 40mm graded aggregate as in sub base complete all as specified & directed. |
| 10 | Plain cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate cast in situ in lintels up to 1.5 m clear span, cills, steps, seismic and other similar bands, hold fast, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, water through and the like including weathering, slightly rounded or chamfered angles and throating including use of form work (straigth or curved) complete all as specified & directed by Engineer-in-charge. - NOTE : (i) The unit rate include for use of form work (straight or curved). (ii) Reinforcement if any shall be measured and paid separately. |
| 11 | Taking up or down GI/PVC pipe and connections 15mm bore ,complete all as specified and directed. |
| 12 | 15 mm bore Galvanized Steel tubes, medium grade including all fittings for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors ,complete all as specified and directed. |
| 13 | Taking up or down GI/PVC pipe and connections 15mm bore ,complete all as specified and directed. |
| 14 | 20 mm bore Galvanized Steel tubes, medium grade including all fittings for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors complete all as specified and directed. |
| 15 | Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings etc and cutting chases for concealed water tubing & making good, cutting not exc 10 cm girth, in brick walls complete all as specified and directed. |
| 16 | Vitreous China Wash down water closet (pedestal pattern) 'P' or 'S' trap white, (excluding, flushing cistern and flush pipe) with and including seat cover & flush pipe fixed to wall and on floor fixed as in repair complete all as specified and directed. |
| 17 | Vitreous china squatting pan, “Orissa” pattern size 580mm x 440mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and flushing pipe, set with cement concrete, fixed as in repair, complete all as specified & directed. |
| 18 | Supply and fixing PVC valve less syphonic action type flushing cistern, low level white in let ball valve, float and handle including brackets complete all as specified & directed. |
| 19 | Toilet paper holder of vitreous china fixed to walls with chromium plated (CP) brass screws fixed as in repair complete all as specified and directed. |
| 20 | 15mm bore Bib taps, cast copper alloy, fancy type long body chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed as in repair complete all as specified and directed. |
| 21 | Supply and fixing in repair two way bib taps, brass (including fixing arrangement of health faucet), fancy type, long body with wall flange, chromium plated with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule, suitable for 15 mm bore pipe, fixed, complete all as specified and as directed by Engineer-in-charge. |
| 22 | Supply and fixing vitreous China Urinal, Half stall type, white complete including providing and fixing clamps, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement including CP Coupling, flush pipe, grating and union for discharged pipe. Make cera sanitary ware S 4020102: Urinal Flat Back Large. Make Jaquar OR Equivalent. |
| 23 | Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect, fixed as in repair complete all as specified and directed. |
| 24 | PVC connections 15 mm size with PTMT nuts of length 450 mm , fixed as in repair complete all as specified and directed. |
| 25 | Wash hand basin, vitreous china, flat back, white of size 550 x 400 mm with waste coupling, angle brackets, PVC connection 15mm size, 450mm long, PVC waste pipe, fixed as in repair complete all as specified and directed. |
| 26 | Table top wash hand basin with CP swan neck pillar tap including SS waste coupling, PVC waste pipe as in repairs complete all as spercified and directed. |
| 27 | Supply and fixing bevelled edge looking mirror, 5.5mm thick of selected quality glass, including wood finish PVC moulding mounted on 6mm thick ply or of PVC frame fixed to wall with screw and rawl plugs, fixed as in repairs complete all as specified and directed. |
| 28 | 15mm bore pillar tap, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, fancy type as in repair complete all as specified and directed. |
| 29 | Angular stop cock, fancy type, cast copper alloy chromium plated, screwed down, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repair complete all as specified and directed. |
| 30 | Stop valve, cast copper alloy, chromium plated, fancy type, screwed down, high pressure with crutch or butterfly handle, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, complete all as specified and directed. |
| 31 | Supply and fix corner sheet glass shelf assembly consosting of 5.5mm thick sheet glass, corner shelf, 300mm radius with chromium plated bracket guard and railing, including fixing at site complete all as specified and directed. |
| 32 | Cast copper alloy, chromium plated, fancy type shower rose with swivel joints 125mm dia including fixing to CPVC pipe 15mm bore, fixed as in repair complete all as specified and directed. |
| 33 | Supply and fixing stainless steel towel rail, 600 mm long fixed with and including chromium plated brass screws and wooden/ plastic cleats (minimum weight 190 gms), fixed as in repair complete all as specified and as directed by Engineer-in-Charge. |
| 34 | Supply and fixing stainless steel towel ring fixed with and including chromium plated brass screws and wooden/ plastic cleats (minimum weight 90 gms), fixed complete all as specified and as directed by Engineer-in-Charge. |
| 35 | Looking mirror of size 600mmx450mm of selected quality mounted on PVC frame and back fixed to wall with screw and rawl plugs, fixed as in repairs,complete all as specified and directed. |
| 36 | PVC (SWR) nahni traps/floor trap 75 dia with grating jointing to waste pipe and setting/fixed in cement concrete type B-1 1:2:4 fixed as in repair complete all as specified and directed. |
| 37 | Material and labour for kitchen sink with drainage board made out of stainless steel sheet 1.0mm thick with plug, washers and wastes, overall size 915 x 460mm, bowl size 410x330x160mm incl fixing cantilever brackets and connection to union, pipe, fixed as in repair complete all as specified and directed. |
| 38 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store complete all as specified and directed. |
| 39 | Supply and fixing PVC (SWR) pipes single socketed in any length with rubber ring joints of pressure rating 6kgf/cm2 fixed complete to laid in trenches, floor etc, 75mm bore single socketed in any length of pressure rating 6 kgf/cm2 , complete all as specified and directed. Note : (i) Joint of pipe with RCC slab (in case of floor trap/ 'P' trap shall be water sealed with crack repair compound. |
| 40 | Supply and fixing PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls of pressure rating 6 kgf/cm2 fixed complete to walls, suspended ceilings or in floors etc., 75mm bore, single socketed in any length , fixed to walls with MS/GI clamps made out of flat iron of size 25mm x 3mm including nuts bolts etc, complete all as specified and directed. Note : (i) Joint of pipe with RCC slab (in case of floor trap/ 'P' trap shall be water sealed with crack repair compound |
| 41 | Supply and fixing PVC (SWR) pipes single socketed in any length with rubber ring joints of pressure rating 6kgf/cm2 fixed complete to laid in trenches, floor etc, 110mm bore single socketed in any length of pressure rating 6 kgf/cm2 , complete all as specified and directed. Note : (i) Joint of pipe with RCC slab (in case of floor trap/ 'P' trap shall be water sealed with crack repair compound. |
| 42 | Supply and fixing PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls of pressure rating 6 kgf/cm2 fixed complete to walls, suspended ceilings or in floors etc., 110mm bore, single socketed in any length , fixed to walls with MS/GI clamps made out of flat iron of size 25mm x 3mm including nuts bolts etc, complete all as specified and directed. Note : (i) Joint of pipe with RCC slab (in case of floor trap/ 'P' trap shall be water sealed with crack repair compound |
| 43 | 110mm bore PVC (SWR) bends any radius, complete all as specified and directed |
| 44 | 110mm bore PVC (SWR) junction single, (Single T) equal or unequal, with access door complete all as specified and directed. |
| 45 | Supply and fixing 110mm bore PVC (SWR) junction single, (Single T) equal or unequal, complete all as specified and directed. |
| 46 | Supply and fixing 110mm bore PVC (SWR) branch piece, double, (double Y) equal or unequal with access door, complete all as specified and directed. |
| 47 | S & F 75 mm bore PVC (SWR) of pressure rating 6 kgf/cm2 ) bends with access door of any radius complete all as specified and directed. |
| 48 | S & F 75 mm bore PVC (SWR) of pressure rating 6 kgf/cm2 ) bends of any radius complete all as specified and directed. |
| 49 | Supply and fixing PVC (SWR) of pressure rating 6 kgf/cm2 ) branch piece, single (single Y) equal or unequal with access door for 75 mm bore pipe, fixed as in repair complete all as specified and directed. |
| 50 | Supply and fixing PVC (SWR) of pressure rating 6 kgf/cm2 ) Junction (single T) equal or unequal with access door for 75 mm bore pipe, fixed as in repair complete all as specified and directed. |
| 51 | M&L for fixing in repairs PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and as directed by Engr-in-Charge. |
| 52 | Plain cement mortar 1:3:6 (type C-2 using 20mm graded aggregate), 75mm thick as in Plinth protection , finishing cement concrete even and smooth without using extra cement, all as specified.Note : 10mm construction joint will be provided and panel should not be more than 3metre in length and joint filled with filler bitumen and sand in ratio (1:3) |
| 53 | Supply and fixing 75mm bore PVC (SWR) vent cowl complete all as specified and directed. |
| 54 | 500 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) double layered, white in colour, screwable lid, hoisted and fixed in position, including ball brass valve 20mm bore etc, fixed as in repairs, complete all as specified and directed. |
| 55 | 1000 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) double layered, white in colour, screwable lid, hoisted and fixed in position, including ball brass valve 20mm bore etc, fixed as in repairs, complete all as specified and directed. |
| 56 | 2000 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) double layered, white in colour, screwable lid, hoisted and fixed in position, including ball brass valve 20mm bore etc, fixed as in repairs, complete all as specified and directed. |
| 57 | Single piece EWC (one piece), minimum size 715 x 335 x 715mm, snow white colour, S-trap with integrated flushing cistern, including slim soft close seat cover , fixed as in repairs, complete all as specified and directed. |
| 58 | M&L for Vitrified ceramic coloured tiles 7 to 8 mm thick (Square or rectangular) area of each tile exc 0.18Sqm but not exceeding 0.36 Sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including screed bed or bedding layer 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and directed.. |
| 59 | Demolition of Stone slabs and tiles of any description or thickness in floors, aprons and skirtinngs etc, laid with any type of mortar. |
| 60 | 20 to 25mm thick, machine cut kota Stone Slab flooring over cement screed bed laid and jointed with neat cement slurry mixed with pigment to match the shade of the slab laid over 20mm thick in cement mortar 1:4, inclduing rubbing and polishing complete all as specified and directed. |
| 61 | 20 to 25mm thick, machine cut kota Stone as in vertical surfaces risers of steps, skirting, dado and pillars etc set and jointed in neat cement slurry and pointed with gray cement mixed with pigment to match the colour of stone slab laid over 10mm thick in cement mortar 1:4, inclduing rubbing and mirror polishing complete all as specified and directed. |
| 62 | 18-20mm thick Granite (of any type table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in, set in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite compelte all as specified and directed. |
| 63 | Material and labour for full body Parking heavy duty tile of size exc 0.09 sqm but n exc 0.18 sqm, laid over and incl 15 mm thick screed bed in CM 1:4 incl jointed with neat cement slurry and pointed in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15 mm thick screed bed in CM 1:4, compelte all as specified and directed. |
| 64 | Demolition of cement concrete in ground floors and pavings not exceeding 15 cm thickness. (Below or above ground level) complete all as specified and directed. |
| 65 | Material and labour for PCC (1:4:8) type B-2 using 40 mm graded stone aggregate as in sub base, surface channels, benching and drains complete all as specified and directed. |
| 66 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & sixe/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand etc complete all as specified and directed. |
| 67 | Taking down existing plaster of any description on brick wall/ concrete surface including racking out joints, hacking for key, scrubbing down with water etc complete, all as specified and directed. |
| 68 | Dubbing out average 20mm thick on irregular faces of walls, exposed reinforced surfaces, in CM 1:4 complete all as specified and directed. |
| 69 | Hard drawn steel wire fabric n exc 4 Kg cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcement, complete all as specified and directed. |
| 70 | Demolition of brick work masonry, built in cement mortar including dismantling all quions, arches, pillars etc complete all as specified and directed. |
| 71 | Brick work using old size bricks, straight or curved on plan exc 6 metre mean radius built in cement mortar 1:6 complete all as specified & directed. |
| 72 | Brick work with sub class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified & directed. |
| 73 | Material and labour for rendering 15 mm thick in cement mortar (1:4) on fair faces of brick work or concrete surfaces mixed with water proofing compound @3% by wight of cement finishing surface even and smooth without using extra cement complete all as specified and directed.Note: WPC shall be measuredand paid separately |
| 74 | Supply only liquid waterproofing compound, all as specified. |
| 75 | 10mm thick rendering in Cement and Sand mortar 1:6 over brick or concrete surfaces finished even and smooth without using extra cement complete all as specified & directed. |
| 76 | Material and labour 5mm thick rendering in Cement and Sand mortar 1:3 concrete surfaces as in ceiling / chajjas facia at any position finished even and smooth without using extra cement complete all as specified and directed. |
| 77 | Preparation of new surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces, complete all as specified and directed. |
| 78 | Newly plastered surfaces of internal wall and applying two coasts of oil bound distemper over 1 mm thick wall care putty on wall plastered surface complete all as specified and as directed. |
| 79 | Newly plastered surfaces of ceiling including plasters, cornics etc and applying two coasts of oil bound distemper complete all as specified and as directed. |
| 80 | Material and labour for preparation of old surfaces of ceiling and applying one coat of oil bound distemper, complete all as specified and directed |
| 81 | M&L for complete removal of existing treatment of surface of walls for applying Two or more coats of 100% exterior Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces |
| 82 | Material and labour for preparation of old surfaces of walls and applying one coat of oil bound distemper, complete all as specified and directed |
| 83 | Supply and fixing Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, incl dismantling of existing roof sheet, complete all as specified and directed complete all as specified and directed. |
| 84 | Stainless steel hanger with 6 pegs complete all as specified and as directed by engineer-in-Charge. |
| 85 | Taking down chowkhats or frame n.exc 1.5 Sqm with shutter (without taking off shutters from the frame) complete all as specified & directed. |
| 86 | Taking down chowkats or frame exc. 1.5 sqm and n exc 4 Sqm with shutters (without taking off shutters from the frame) complete all as specified and directed. |
| 87 | Taking down shutters of any description exc 1 sqm but n.exc 2 sqm each complete all as specified and directed. |
| 88 | Taking down shutters of any description exceeding 1Sqm but not exceeding 2sqm each including stacking at location as directed by Engineer-in-Charge for refixing in same opening(s) after rescuring or easing, adusting, welding, etc., complete all as specified and directed. |
| 89 | Factory made pressed steel frames having profile 125mm x 60mm for doors with one or more rebates made out/fabricated of 1.25 mm thick MS sheet, including necessary fixing lugs, hinges, lock strike plate, thress hold bar/flat etc. complete ,all as specified and directed. |
| 90 | Factory made pressed steel frames having profile 105mm x 60mm for doors with one or more rebates made out/fabricated of 1.25 mm thick MS sheet, including necessary fixing lugs, hinges, lock strike plate, thress hold bar/flat etc. complete ,all as specified and directed. |
| 91 | Framed work such as grills, gratings, etc with ends of bars shouldered and / or riverted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, raillings, frame work of water tanks and similar work confirming to Fe-410 grade Fe-310 complete all as specified & directed by Engineer-in-charge. |
| 92 | Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 100/ 50 x 75 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). |
| 93 | Glazed & Skeleton shutter (Factory made) 35mm thick of second class hard wood open rebated & prepared to receive glass, gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut & mitred beads for securing glass etc including priming coat. Size of members of shutters as specified in SSR Part I Section 8, clause 8.24 (a) including Kiln seasoned and chemically pressure treated, complete all as specified & directed. |
| 94 | Factory made flush shutters 30mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and directed. |
| 95 | Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). |
| 96 | Soild panel PVC board 20mm to 25mm thick with 2mm thick prelam PVC sheet on the front face & 2mm prelam PVC sheet on back with particle board core fixing in frame at site to cupboard shutter, shelves and kitchen cabinet complete all as specified and directed. MAKE: RAFSHREE, ECOCELL OR EQUIVALENT. |
| 97 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge |
| 98 | Supply and fixing factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS squared tube, fixing in opening at site as per specifications & drawing, complete all as per directed. |
| 99 | Supply and fixing factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC “C” channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame at site as per specifications & drawing complete all as specified and directed. |
| 100 | S&F 100mm butt hinges of Stainless Steel hinge pin,Type-B-21 complete all as specified and directed. |
| 101 | S&F of 150 mm long Extruded aluminium alloy handles, fabricated type anodized , complete all as specified and directed. |
| 102 | S&F of 150 mm aluminum anodized barrel tower bolts of extruded section, complete all as specified and directed. |
| 103 | S&F of aluminium alloy, anodized, sliding door bolt 250mm long hasp , staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy and fixed complete all as specified and directed. |
| 104 | Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm including fixed with stainless steel wire staples, complete all as specified & directed. |
| 105 | Continuous (Piano) hinges, bright finish or electrogalvanised 30mm (width of flap when open) , mild steel , complete all as specified and directed. |
| 106 | Material and labour for hasp and staple 100mm size (ISI Marked), safety type aluminum anodized including bolt to hinge plate, fixed as in repair all as specified and directed. |
| 107 | magnetic door catcher for kitchen cup boards, including all fixing arrangement, complete all as specified and directed. |
| 108 | Preparation of new or previously untreated wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) over a coat of Pink primer complete all as specified and directed. |
| 109 | Mild steel, plain, black sheet 1.25mm thick in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required, as in repair complete all as specified and directed. |
| 110 | Two coats of synthetic enamel paint on steel and iron surfaces over one coat of red oxide primer on surfaces over 10 cm width or girth including preparation of new surfaces complete all as specified & directed. |
| 111 | Powder coated aluminum sections as in frames/ shutter of doors/window/ventilators /partitions, (Sliding / openable/ three track) including joinging cleats, glazing clips, rubber neoprene beading, powder coated aluminim snap beading, screws etc. complete all as specified and directedNote : (i) Minimum thickness of power coating shall not be less than 50 micron.(ii) Weight of aluminum section only shall be measuerd and paid.(iii) Aluminum doors/windows /ventilators to be fixed to jambs with chromium plated screws .(iv) The rate shall be inclusive of neoprene beadings, snap beading, screws etc and in case of sliding shutters locking arrangement and rollers in sliding shutters. Weight of fitting fixtures will not be measured for arriving the weight of aluminum section.(v) Glass /wooden panel/ACP sheet shall be measured and paid separately under respective items.(vi) Design as directed by Engineer in charge. |
| 112 | 4.80mm thick ordinary quality tinted glass, fixed to aluminum frame work in panels n. exc 0.5 Sqm in each pane, complete all as specified & directed. |
| 113 | 4mm thick aluminium composite panel sheet (ACP) fixed with aluminium beading with rubber gasket including all necessary clips and fittings colour as approved by Engr-in-Charge all as specified and directed. |
| 114 | Hacking out old broken glass (any thickness size, quality or discription) from wooden frames or stone, concrete or brick surrounds, glazed with putty complete all as specified and directed. |
| 115 | 4mm thick sheet glass ordinary quality any size and in any type of frame and glazing with oil putty (or beading) in square n.exc 0.5 Sqm in each panes complete all as specified and directed. |
| 116 | 4mm thick figured glass pin head type ordinary quality any size and in any type of frame and glazing with oil putty (or beading) in square n.exc 0.5 Sqm in each panes complete all as specified and directed. |
| 117 | Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm including fixed with stainless, including all necessary nut bolt, wooden bidding, FI, welding as per site requirement, as in repair, complete all as specified & directed. |
| 118 | Repair to old aluminium door/window including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285 ,(Excluding aluminium material for shutter frame ) fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, including dismantling & refixing of door if required complete all as specified and directed by Engineer-in-Charge.Note : (i) Glass panes and panels shall be measured & paid separately under respective items (If required). |
| 119 | 10mm thick toughned glass as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holeswith necessary screws/ beading, rubber packing, L Patch bottom and top, self clossing patch etc complete all as specified and directed. |
| 120 | Door closer hydraulically regulated aluminum (die cast) body, designation No 3, universal type, suitable for door shutters of 701mm to 850mm in width and of weight between 36 to 60 Kg, complete all as specified and directed. |
| 121 | Mortice lock, verticle type, mild steel, 4 levers, size 100mm, brass body, complete all as specified and directed |
| 122 | Door closer hydraulically regulated of aluminium extruded section, designation No. 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg, fixed as in repair complete all as specified and directed. |
| 123 | Material and labour for floor door stopper of aluminum alloy body and tongue, anodized with hard drawn steel spring, fixed in floor (140mm size), complete all as specified and directed. |
| 124 | Stainless steel lock for 10-12mm thick glass door, having knob inside with three keys, satin finish, complete all as specified and directed. |
| 125 | 300 mm long stainless steel handle, fancy type , fixed to toughened glass, complete all as specified and directed. |
| 126 | Factory made steel window box type with side hung shutters including box type hinges and one shop coat of red oxide primer, 125mm steel handle-02 Nos mild steel ISI marked tower bolt 125mm size (minimum 2 for each shutter) complete with glazing bars, dovetailed or welded fixed with and including MS flat of suitable size for fixing grills and guards bars etc as in repairs, complete all as specified. |
| 127 | Factory made steel window box type with side hung shutters including box type hinges and one shop coat of red oxide primer, 125mm steel handle-02 Nos mild steel ISI marked tower bolt 125mm size (minimum 2 for each shutter) complete without glazing bars, dovetailed or welded fixed as in repairs, complete all as specified. |
| 128 | 25mm dia stainless steel curtain rod fixed to bracktes, including brackets, finale cap and all fixing arrangement etc complete all as specified and directed. |
| 129 | Steel rolling shutters (1 mm thickness of lath) with ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated complete, gear operated type with bevel gear box and crank handle, fixed as in repair complete all as specified and directed. |
| 130 | Safety lever locks mild steel with 4 levers in steel rolling shutters fixed as in repair complete all as specified and directed. |
| 131 | Steel rolling shutters (1 mm thickness of lath) with/ without ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated complete, push pull or manual type fixed as in repair complete all as specified and directed. |
| 132 | Preparation of new steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint complete all as specified and directed. |
| 133 | Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified & directed by Engineer-in-charge. |
| 134 | Powder coated GI Frame work grid Size of grid 605 x 605mm for ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm, fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre with hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long, complete all as specified and directed |
| 135 | 4mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws fixed in ceiling flat or sloping complete all as specified. |
| 136 | PVC lining coloured or selective pattern, as in repair PVC lining of hollow profile not less than 5mm thick and not less than 250mm wide intelocking type system as in wall/celing linings including end and intermediet U or L PVC sections as per manufacturer instructions including dismantling existing paneling, complete all as specified and directed(Note : Colour/design and pattern shall be as decided by the GE) |
| 137 | Louvers wall panels with thickness not less than 10mm thick and not less than 250mm wide intelocking type system as in wall/celing linings including end and intermediet U or L PVC sections as per manufacturer instructions fixed as in repair complete all as specified and directed(Note : Colour/design and pattern shall be as decided by the GE) |
| 138 | Applying one coat of synthetic enamel paint on steel and iron surfaces over 10 cm width or girth including preparation of old surfaces complete all as specified & directed. |
| 139 | Preparation of old wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 140 | Material and labour for preparation of old surfaces of walls and applying one coat of oil bound distemper, complete all as specified and directed |
| 141 | Demolition of brick tiles or terracing tiles, pointed in cement mortar along with cement screed or plaster and removing rubbish etc outide the MOD land complete all as specified and as directed by engineer-in-charge. |
| 142 | Demolition of mud phuska as in roof of any thickness incl plastering and leeping etc (whether full thickness removed or only a part thereof), removal of debris complete all as specified & directed. |
| 143 | Providing plain cement concrete 1:2:4 type B0 (12.5mm graded stone aggregate), 50mm thick (averaging), as in levelling course on roofs, complete all as specified and directed. |
| 144 | Rendering 10mm thick rendering in CM 1:4 plaster mixed with water proofing compoound on roof surfaces including junction of parapets etc., and adjoin vertical surface and applying bituminous primer @ 0.40 ltrs per square meter including APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3 mm thick reinforced with polyester non woven fabric (weight not less than 150 gm/sqm) laid on primed surface by torch application & preparatio of surface complete all over as specified and directed.Note: WPC shall be measured and paid for separately |
| 145 | Fixing only 20 mm bore GI tubes, any grade, to wall and ceilings or laying in floor complete including new fittings all as specified and directed by engineet-in-charge |
| 146 | Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner complete all as specified and directed. Please Enable Macros to View BoQ information |
