|
| 1 | Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and as directed. |
| 2 | Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed. |
| 3 | Demolition of unreinforced cement concrete in ground floors and pavings not exc 15 cm thickness (below or above ground level) |
| 4 | Taking down chowkhat or frames with shutters (without taking off shutters from the frames) including iron mangory exc. 1.5 sqm but not exc 4 sqm each complete all as specified and directed. |
| 5 | Taking down chowkhat or frames with shutters (without taking off shutters from the frames) including iron mangory not exc. 1.5 Sqm each complete all as specified and directed. |
| 6 | Dismantling of Stone slabs and tiles of any description or thickness laid bedded and pointed in any mortar in floors, aprons, slabs, shelves etc. complete all as specified and as directed. |
| 7 | Taking down plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and as directed. |
| 8 | Dismantling of Wall and ceiling boards (fibre,pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets, complete all as specified and as directed. |
| 9 | Taking down roof trusses, coupled rafters or trussed beams upto 4.00 m span |
| 10 | Taking down roof trusses, coupled rafters or trussed beams exc 4.00 m but not exc 8.00m span |
| 11 | Excavating in trenches, not exc 1.5 m wide and not exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc 10 sqm on plan and not exc 1.5 m in depth and getting out in hard dense soil, complete all as specified and as directed. |
| 12 | M & L for Plain Cement concrete (1:4:8) Type D2 using in foundations, filling and mass concrete, complete all as specified and as directed. |
| 13 | Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6, complete all as specified and as directed. |
| 14 | M &L TMT bar 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed. |
| 15 | Description all as per item No 14 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, complete all as specified and as directed. |
| 16 | Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, for fair finished flat surface, complete all as specified and as directed. |
| 17 | RCC M-25 design mix (20mm graded aggregates) as in fdn, including raft, footing fdn beams plinth beams bases for columns, complete all as specified and as directed. |
| 18 | Formwork to sides of pillars, posts, struts, piers, columns and stanchions, complete all as specified and as directed. |
| 19 | RCC M-25 design mix (20mm graded aggregates) as in columns, pillars, piers, posts and struts etc. |
| 20 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. |
| 21 | Removing excavated material not exc. 50m and depositing where directed at a level not exc. 1.5 m above the starting point, complete all as specified and as directed. |
| 22 | Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface, complete all as specified and as directed. |
| 23 | M&L for 75 mm thick cement concrete type D-2, 1:4:8 (using 40mm graded agg) as in Sub-base to floor finishes. |
| 24 | Formwork to staircases with sloping or stepped soffits including risers and stringers (excluding landing) Flat including fair finish. |
| 25 | Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) Flat including fair finish. |
| 26 | RCC M-25 (Design mix) as in stairways (except spiral staircases) including steps (square or spandrel), string pieces, carriages, etc, complete, any section straight or winding, but excluding landings; RCC water tanks upto 1500 litre, complete all as specified and as directed. |
| 27 | RCC M-25 (Design mix) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like |
| 28 | RCC M-25 (Design mix) as in Beams, cantilevers, bressummers, lintels over 1.5m span, complete all as specified and as directed. |
| 29 | Formwork to sides and soffits of floor or roof beams, beam hauntings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. |
| 30 | Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM (1:4), complete all as specified and as directed. |
| 31 | Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pilasters, buttresses, etc.; vertical or to batter, complete all as specified and as directed. |
| 32 | Formwork to chullah hoods, chajjas, troughs and similar items including edges, Flat surface incl fair finish, complete all as specified and as directed. |
| 33 | RCC M-25 (Design mix) as in Chajjas, complete all as specified and as directed. |
| 34 | Rendering 10mm thick using Cement mortar (1:6) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement, complete all as specified and as directed. |
| 35 | Rendering 5mm thick using Cement mortar (1:3) concrete surfaces in ceiling, finished even and smooth without using extra cement. |
| 36 | Rendering 5mm thick using cement mortar 1:4 over 10mm thick using Cement mortar (1:6) on other than fair faces of brick work or concrete surfaces finished even and smooth without using extra cement, complete all as specified and as directed. |
| 37 | Supply only Liquid water proofing compound, complete all as specified and as directed. |
| 38 | M&L for Vitrified Ceramic tiles light shade 8 to 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors over and including 15mm thick screed bed of CM (1:6) etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and as directed. |
| 39 | M&L for non skid ceramic tiles 7 to 8mm thick (square/rectangular) polished, area of each tiles exceeding 0.09 sqm but not exceeding 0.16 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and as directed. |
| 40 | M&L for Vitrified Ceramic tiles light shade 8 to 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in riser of steps, skirting, dado and pillar etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over cement 10mm thick cement mortar 1:6, complete all as specified and as directed. |
| 41 | M&L for Coloured ceramic tiles 7 to 8 mm thick (square/rectangular) polished, 300X600mm as in wall over and including 10mm thick rendering in CM (1:6) as in wall, skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and as directed. |
| 42 | M&L for pre polished factory made machine cut kota stone slab flooring 22 to 25mm thick using PVC spacer over 20mm thick cement screed bed in CM (1:4), laid and jointed with white cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete |
| 43 | M&L for 50 mm thick Cement concrete type B-1, 1:2:4 (using 20mm graded aggregate), finished even and smooth without using extra cement in floor, complete all as specified and as directed. |
| 44 | M&L for 2 Coats of OBD over a coat of primer and 2mm thick wall care putty incl preparation of newly plastered surface on walls. |
| 45 | M&L for 2 Coats of OBD over a coat of primer and 2mm thick wall care putty incl preparation of newly plastered surface on Ceiling surface. |
| 46 | Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces. |
| 47 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with mitre joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Make 'Rajshree/ Black Cobra or equivalent' |
| 48 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibbers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, including 3 Nos stainless steel butt hinges of size 100mm, 2 Nos 150mm long stainless steel tower bolt and 01 No 250mm long sliding bolt of all as per direction of Engineer-In-Charge. Make 'Rajshree or equivalent \\" |
| 49 | S & F for Factory made UPVC (white/Off white colour) sliding window three track made out of extruded profiles with wall thickness of members as 2.3mm (+0.2mm). Window profile with hollow section with multi chamber frame (60mm x 62mm) sash bars (42mm x 67mm). Sliding inter lock (one in each shutter 45.5mm x 28mm). Glazing head (24.5mm x 16mm) members will be mitred, cut and fusion welded in all corners including drilling of holes for fixing hardware and drainage of water. Making arrangement for fixing of hardware, EPDM gaskets 1.2, +0.2mm thick galvanised steel frame (30mm x 21.50mm). Sash bars (30mm x 18mm) profile to be inserted in required profile frame and will be fixed to the wall with 8mm x 100mm long fasteners. Hardware : Touch lock to be of Zinc alloy (white powder coated), Steel roller system including 5mm thick glazing with selected quality glass, Aluminium track on bottom rail to be of here track sliding frame, wool pine for sliding sash and interlock, complete all as specified and as directed.(Note: The unit rate quoted by contractor includes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.) |
| 50 | S & F for Factory made UPVC (white/Off White colour) casement (Openable) Door made of extruded profile members with wall thickness of 2.3mm (+0.2mm). Door profile members with hollow section with multi chamber. Frame (60mm x 60mm), sash bars (60mm x 110mm). T-profile (One vertical length in between two shutters 60mmx 74mm). Glazing head (35mmx 20mm) will be mitred cut and fusion welded at all corners, including making of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware EPDM gasket 1.2 to 0.02mm thick galvanised steel frame (28mmx21.50mm), sash bars (31mmx27mm). T-profile (27x17mm) to be inserted in required profile frame and will be fixed to wall 8mm x 100mm long fasteners. Hardware: casement door handle made of zinc alloy (white powder coated), Corner striker, Secondary Strikers, Cylinder, Door transmission gear made of mild steel with multi point locking system with striker, Hinges of zinc alloy (white powder coated) and 5mm thick toughened glazing with selected quality glass, complete all as specified and as directed.(Note: The unit rate quoted by contractor includes cost of glass, hydraulic door closure, lock and includes all other connected accessories. Net opening will be measured for payment purpose.) |
| 51 | Description all as per item no 50.00 Above but with SS Wire mesh complete all as specified and directed. |
| 52 | S & F for Stainless Steel work of Grade-304 as in Gates, grills, railing posts (horizontal/vertical) or any type of other work or in any position, of any type and size including special shaped washers, channels, plates horizontal/ vertical made of hollow tubes or in any other shape as per requirement at site complete all as specified and as directed. |
| 53 | S&F for Stainless steel butt hinges 100 mm long, medium weight, and fixed complete all as specified. |
| 54 | S&F stainless steel sliding door bolt 300 mm with hasp, staple (bolt type) and fixing clips of sheet, |
| 55 | S&F for stainless steel , barrel tower of 200mm long bolts of extruded section and fixed |
| 56 | S&F for stainless steel handle cast type anodised,150mm long all as specified and directed. |
| 57 | M&L Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall, complete all as specified and as directed. |
| 58 | Hard core of broken bricks gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick watered and well rammed to a true surface. |
| 59 | M&L for 50 mm thick cement concrete 1:3:6, type C-2 (using 40mm graded agg) as in plinth protection finished even and smooth using extra cement.(incl necessary joint filling with mixture of paving bitumen & sand in 1:3), complete all as specified and as directed. |
| 60 | BLANK |
| 61 | M&L for RCC (1:2:4) type B1 using 20mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or |
| 62 | S&F 15mm bore GI tubing medium grade with all fittings and fixed to wall and ceiling including cutting chases or laid in floors etc complete all as specified and directed. |
| 63 | Description all as per item No 62 above but 20 mm bore. |
| 64 | S&F white colour Rotational moulded polyethylene water storage tank 1000 litres capacity, white triple layer construction (cylindrical vertical closed top), hoisted & fixed in position including 20 mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed with all fittings complete all as specified and as directed. |
| 65 | S&F 15 mm dia brass chromium plated central hole basin mixer, fancy type with or without lettered 'Hot' or 'Cold' ,with long screwed shanks and fly nut capstan head screwed for 15mm dia pipe . (Make Jaquar Florentine FLR-CHR 5273UPR/ Pearl GPR-884/ Cera F1017401) |
| 66 | S&F CP towel rail 600mm long fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 190 gms) fixed on walls, complete all as specified. (Make: Jaquar/ Marc/ Kohler) |
| 67 | S & F Vitreous china single Piece floor mounted WC With PP Soft Close Seat Cover, Hinges, with cistern & Dual Flush Cistern Fitting, Fixing Accessories and Accessories Set, Size: 360x730x740 mm, S Trap- 300 mm including connection to drain pipe with all fitting and fixture complete all as specified and as directed. Make & Cat Part : Jaquar-Cat No. SLS-WHT-6851S300PP or equivalent in Marc / Kohler ) |
| 68 | S & F ready made floor/wall mounted Vanity box made of HDHMR board, both side laminated consisting of the following combination :-(a) Wash Hand Basin 810mm x 500mm with CP grating and CP bottle trap.(b) Base Cabinet 780mm x 485mm x 460mm.(c) Side Cabinet 300mm x 250mm x 1800mm.(d) Mirror cabinet size 780mm x 160mm x 800mm.Make : Hindware - Cat Part No. 70089 or 70084.Make : Kohler : Cat Part No. K-31602IN-E63 or equivalant make of Kohler. |
| 69 | S&F 15 mm dia stop cock/angle cock cast copper alloy chromium plated concealed type screwed down high pressure with crutch or butterfly handle, flinch screwed both ends for iron or for union. (make: Cera new cat no F2002201, Jaquar cat no CON-CHR-053 KN, Pearl cat no ARI-004). |
| 70 | S&F bib taps brass chromium plated 15 mm bore size screwed down screwed for iron pipe or for brass ferrule (make: Cera cat no F1015151, Jaquar cat no continental CON-CHR-047 KN/ Pearl cat no ARI-003) or equivalant make of Jaquar. |
| 71 | S&F Stainless steel grating 100mm dia with centre hole of best quality as approved by GE including fixing in CM 1:4 to floor/nahani traps etc complete all as specified and directed. |
| 72 | S&F Gun-metal globe or gate valves 20mm bore with iron wheel head, screwed both ends for iron complete all as specified and directed. |
| 73 | S & F Designer type high quality fancy type looking mirror of size as approved by Engr-in-Charge 8-10mm thick, fixed to wall with stainless steel studs, screws, brackets and washers etc complete all as specified and as directed. |
| 74 | S&F PVC connection 15 mm bore and 45cm long with washers complete all as specified and directed. |
| 75 | S&F Hubless CI pipes of 100 mm nominal diameter ( single socketed in any length with rubber ring joints and clamps including all fittings/fixtures fixed on wall or in trenches or in floor complete all as specified and directed. |
| 76 | Description all as per item No. 75 above but 75mm nominal outside diameter. |
| 77 | S&F Hubless CI 100mm dia (single T) or unequal provided with access door complete all as specified and directed. |
| 78 | S&F Hubless CI 75mm dia (single T) or unequal provided with access door complete all as specified and directed. |
| 79 | S&F 100 mm bore CI hubless bends/shoes any radius complete all as specified and directed |
| 80 | Descirption all as per item No. 79 above but 75 mm bore. |
| 81 | S&F 100 mm bore CI hubless diminishing pieces or tapers (larger bore measured) any radius complete all as specified and directed |
| 82 | S&F Hubless cowl of 75mm dia complete all as specified and directed. |
| 83 | S&F UPVC (SWR) 110 mm Nahani trap with grating including jointing to waste pipe in cement concrete complete all as specified and directed. |
| 84 | S&F UPVC (SWR) floor trap, 75mm dia plain including jointing with solvent cement with grating including jointing to waste pipe in cement concrete complete all as specified and directed. |
| 85 | S & F for Wall mounted multiple function Shower Panel including all accessories and fittings, fixed s, complete all as specified and as directed. Make : Hindware Cat Part No. 511686 (size 1650mm x 150mm x 550mm)/Jaquar Cat Part No. JPL-SSF-ST88148B(size 1600mm x 200mm) or JPL-WHT-TMCURVENEO (size1500mm x 230mm) or equivalent in Cera/Somany |
| 86 | S & F stainless steel Curtain Rod 25 mm dia with holders fixed to wall with finials and bracket etc complete all as specified and as directed. |
| 87 | S&F Stainless steel plain basket of size 445mm x 485mm x 200 mm made of min 4mm dia stainless steel wire and bottom of S perforated sheet approved quality with suitable arrangement for fixing over and including telescopic channel 18 inches/ 20 inches in length two way extruded MS galvanised over rollers. (Make: Godrej Cat part No 3892, or equivalent in IPSA/ Hettich). |
| 88 | S&F for Stainless steel thali/plate basket of size 445mm x 485mm x 200 mm made of min 4mm dia stainless steel wire of approved quality with suitable arrangement for fixing over and including telescopic channel 18 inches/20 inches in length two way extruded MS galvanised over rollers. (Make: Godrej Cat part No 3441or equivalent in IPSA/ Hettich). |
| 89 | S&F Stainless steel basket (Perforated Cutlery Basket SS) of size 445mm x 485mm x 100mm made with suitable arrangement for fixing over and including telescopic channel 18 inches/ 20 inches in length two way extruded MS galvanised over rollers. (Make: Godrej Cat art No 3575 or equivalent in IPSA/Hettich). |
| 90 | S&F Stainless steel two shelf pullout basket of size 150 mm x 450mm x 430 mm made of min 4mmdia stainless steel wire and bottom of S perforated sheet approved quality with suitable arrangement for fixing over and including telescopic channel 18 inches/ 20 inches in length two way extruded MS galvanised over rollers. (Make: Godrej Cat part No 2260, or equivalent in IPSA/ Hettich). |
| 91 | S & F Sinks (Double bowl) made of stainless steel 1mm thick as in kitchen with plugs, washers and wastes, including bedding in cement mortar on to dwarf walls or including cantilever brackets and connecting union to pipe overall size 915mmx460mm, double bowl (each bowl size 410mm x 330mm x 160mm), fixed s, complete all as specified and as directed. (Make : Nirali/Jayna/Diamond) |
| 92 | S & F Toilet paper holder chromium plated with flap all as directed. (Make : Jaquar/Marc/Kohler) |
| 93 | S & F stainless Steel Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and as directed. (Make: Jaquar/Marc/Kohler) |
| 94 | S& F stainless steel-304, towel rack of size 600 mm x 350mm, with two shelves fixed with brass screws, fixed, complete all as specified and as directed. (Make: Jaquar/Marc/Kohler ) |
| 95 | S & F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed. (Make: Jaquar/Marc/Kohler/Prayag) |
| 96 | S & F glass corner shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed. (Make: Jaquar/Marc/Kohler/Prayag) |
| 97 | M & L for fabrication & fixing to horizontal & vertical shelves/ partitions /sides/ top/ bottom/back sides etc. for Modular kitchen cabinet/ wardrobe/ cupboard/drawers made out of 17/18 mm thick WPC boards with white laminated colour on both sides, of approved quality including paste to all exposed edge by edge Banding Tape including provision of cabinet for keeping baskets/ drawers etc. complete all as specified and as directed. (Make :Action tesa or equivalent) |
| 98 | M & L for Fabrication & fixing to front side /all exposed sides of Modular kitchen cabinet/ wardrobe/ cupboard/drawers made out of 17/18 mm thick HDHMR boards with glossy/mat colour laminate sheet on front face and all exposed sides and white laminate on other face of approved quality and including paste to all exposed edge by edge Banding Tape and including provision of cabinet for keeping baskets/ drawers etc. complete all as specified and as directed. (Make :Action tesa or equivalent) |
| 99 | S & F for soft closure hinges with all fittings at mounting plate of premium quality, fixed in door/cup board shutters complete all as specified and as directed. (Make : - Godrej/Hettich/IPSA). |
| 100 | S & F 150 mm size designer door handle stainless steel chromium plated for Cabinet/Wall Unit/Overhead Unit/Wardrobe etc. complete all as specified and as directed. |
| 101 | S & F for Magnetic catches with steel body ‘H’ type, fixed to shutter, complete all as specified. |
| 102 | M & L for glossy finished coloured Chequered cement concrete tiles 30cm x 30cm x 20-22mm thick, set, jointed and pointed in neat cement slurry over & including 15mm thick screed bed in CM 1:6, complete all as specified and as directed |
| 103 | M & L for Machine pressed precast concrete interlocking paver block of any shape and size (Two colour combination) conforming to IS 15658-2006 of 60 mm thick, M-35 Grade laid dry in floor/path including 50mm thick sand cushioning, complete all as specified and as directed |
| 104 | M&L for point wiring complete with 1.5 Sqmm (nominal area) FRLS-H, PVC insulated un-sheathed and stranded copper conductor cable ISI marked drawing in PVC concealed conduit and PVC conduit fitting including drawing FRLS-H, PVC insulated unsheathed 1.5 Sqmm copper earth wire, connecting to common earth dolly with and incl Metal flush box of suitable size with modular sheet for fixing modular switches/ sockets/ fan regulator etc complete all as directed |
| 105 | One light point / fan point/ wall fan point/ bell/ buzzer controlled by one 1-way switch/ bell push. |
| 106 | One socket outlet point 5 amps on the same board. |
| 107 | One socket outlet point 5 amps on the independent board. |
| 108 | One light point controlled by two 2 way switches |
| 109 | Description all as per Srl Item No 104.00 here-in-before but with 2.5 sqmm FRLS-H copper wire with 2.5 Sqmm FRLS-H copper earth wire for independent point. |
| 110 | Description all as per Srl Item No 104.00 here-in-before but with 4 sqmm FRLS copper wire independent point suitable for Geyser and Air Conditioning with 4 Sqmm FRLS-H copper earth wire for independent point. |
| 111 | S&F Modular switch 6 Amp, 1 way, 1 module size complete all as directed by Engineer-in-Charge white/Black/ Brown complete all as specified and directed. Make-Indoasian shynora/Legrand Artear/Havells murano/Gold medal Gifa-X9 or equivalent. |
| 112 | S&F Modular socket 6 Amp, 2/3 pin, universal type, 2 module size complete all as directed by Engineer-in-Charge white/Black/Browncomplete all as specified and directed.Make-Indoasian shynora/Legrand Artear/Havells murano/Gold medal Gifa-X9 or equivalent. |
| 113 | S&F Modular switch 16 Amp, 1 way, 1 module size complete all as directed.by Engineer-in-Charge white/Black/ Brown complete all as specified and directed. Make-Indoasian shynora/Legrand Artear/Havells murano/Gold medal Gifa-X9 or equivalent. |
| 114 | S&F Modular socket 16 Amp multipurpose shuttered type, 2 module size with indicator lamp complete all as directed by Engineer-in-Charge white/Black/Brown complete all as specified and directed. Make-Indoasian shynora/Legrand Artear/Havells murano/Gold medal Gifa-X9 or equivalent. |
| 115 | S&F modular switch flush type, IP 20 rated,shrouded terminal 6 amps two way, SP, 230 volts AC all as directed by Engineer-in-Charge white/Black/Browncomplete all as specified and directed. Make-Indoasian shynora/Legrand Artear/Havells murano/Gold medal Gifa-X9 or equivalent. |
| 116 | S&F Modular Bell push 6 Amp, 1 way, 1 module size complete all as directed. by Engineer-in-Charge white/Black/ Brown complete all as specified and directed. Make-Indoasian shynora/Legrand Artear/Havells murano/Gold medal Gifa-X9 or equivalent. |
| 117 | S&F Ceiling rose, insulated body, 3 terminal, 240 volts, 5 Amps and making good surface as original by plastering and whitewash/ colour/ distemper etc complete all as directed. |
| 118 | S&F Modular Step Fan regulator, 120/70 watts single / double module, fixed in repairs, complete all as specifed and as directed. Make-Indoasian shynora/Legrand Artear/Havells murano/Gold medal Gifa-X9 or equivalent. |
| 119 | S&F Bell Ding Dong type AC, 230 volts, single pole complete all as directed. |
| 120 | Supply and fixing of Flexible LED tubelar light (120 LED per RM) cool/warm white and making all electric connection complete all as directed. Make - Havells/Eveready or equivalent. |
| 121 | Supply and fixing of adopter AC to DC 12 Volt suitable for tubelar LED light complete all as directed. |
| 122 | S & F of LED batten luminaire surface mounted with aluminium housing & PC diffuser ,4 feet system wattage of 20 watts not less than 2000 initial lumen, maintained CRI>80,Power Factor >0.9,THD<20%,colour temperature-6500K,surge Protection 2.5 KV in CM,IP-20 protected,meets LED IS specified,Class-1,short circuit and over circuit protection ,voltage range -140 to 270 volts AC,temperature range 0 to 50 Degree C,system efficiency at luminaire level >120 Lumen/watts and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire from ceiling rose to fitting fixed complete all as specified and directed. |
| 123 | S & F of LED batten luminaire surface mounted with aluminium housing & PC diffuser ,2 feet system wattage of 10 watts not less than 1200 lm initial lumen maintained CRI>80,Power Factor >0.9,THD<20%,colour temperature-6500K,surge Protection 2.5 KV in CM,IP-20 protected,meets LED IS specified,Class-1,short circuit and over circuit protection ,voltage range -140 to 270 volts AC,temperature range 0 to 50 Degree C,system efficiency at luminaire level >120 Lumen/watts and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire from ceiling rose to fitting fixed complete all as specified and directed. |
| 124 | S & F of ceiling fan(BLDC) 1200 mm sweep, 5 star rating regulator operated, service value not less than 6.0, 240 volts, 240 Volts. 50 Hz complete all as specified and directed and depositing the old u/s to MES store yard. |
| 125 | M&L Sub main wiring with 2 run of 10.0 Sqmm (nominal area) FR, PVC insulated, unsheathed and stranded copper conductor cable ISI marked, drawn in to separate PVC concealed conduit 25 mm dia with and including 10.0 Sqmm (nominal area) FR, PVC insulated, unsheathed and stranded copper conductor cable ISI marked as earth wire, connected with thimble from main DB to sub main DB complete all as directed. |
| 126 | Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm and depositing the old U/s item to MES store yard. |
| 127 | Supply and fixing of MCCB incommer Distribution Board ( Vertical Load line DB) double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, VTPN 04 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCCB as incommer and MCB as outgoing and making all necessary connections and taking out the old unserviceable DB complete all as directed. Note:- MCCB & MCBs will be measured and paid separately |
| 128 | S&F MCCB 3 Pole, 160 Amp with breaking capacity 16 KA suitable for 415 volts AC supply, with over load and short circuit protection complete all as specified. |
| 129 | S & F of MCB DB conforming to IP 43 - IK 09 with double door , SPN 16 way complete with din rail Neutral and earthing bar after taking out the oldunserviceable DBs connection and making good the disturbed surfaces complete all as specified and as directed. |
| 130 | S&F of MCB SP, B Curve type, 10 KA, 10 to 32 Amp, with over load and short circuit protection complete all as directed. |
| 131 | S&F of MCB SPN B Curve type, 10 KA,63 Amp, with over load and short circuit protection complete all as directed. |
| 132 | Supply and fix of Modular AC 25 Amp SP mini MCB, 230 Volts, 50 Hz suitable for module sheet complete all as specified and as directed. |
| 133 | Supply and fix Automatic Hand drier hot air dispenser with infrared sensor metal body with all accessories including all electrical connection complete all as specified and as directed.Make-Euromics(E4270N) or equivalent. |
| 134 | S & F Designer type high quality fancy type looking mirror of size exc 0.75 sqm but not 1.50 sqm with variable LED light with touch screen sensor as approved by Engr-in-Charge, 8-10 mm thick,fixed to wall with stainless steel studs,screws,brackets and washers etc complete all as specified and as directed. |
| 135 | Supply and Fixing high quality DSDR0112 white automatic sensor type hand sanitizer dispenser 1100 ml wall mounted type electric/battery operated all as specified and as directed by Engr-in-Charge |
| 136 | S&F electric water heater of capacity 25 litre, vertical storage type, steel inner tank with glass linen 5 star rating, withstand 8 bar pressure complete with all accessories such as heating element, pressure relief check safety valve, thermostat, connection piece, 3 core wire with plug etc all as specified and as directed. |
| 137 | S&F Steel fastner of 4\\" long and 8mm dia with Nuts & washer complete all as specified and as directed. |
| 138 | Supply and fixing of steel wired connection 600 mm long and C P brass adopter 15 mm dia with washer for hot and cold water from geyser and to withstand 8 bar pressure of water complete all as specified and as directed. |
| 139 | S&F of LED bulk head fitting 10W with inbuilt driver complete all as specified and directed. |
| 140 | S & F of LED Bolard garden light Fittings with B22 LED lamp ,height of light 900 mm suitable for pathway lights including making base of PCC 1:2:4 (45x45 cm) with fixing fastner,Nut,Bolts in PCC from ground level and making good electric connections, complete all as specified and as directed. Make :-1xRetrofit LED Lamp Cat No - Li-8158 or Equivalent |
| 141 | S&F cable PVC insulated copper conductor three core PVC sheathed circular 6 sqmm for electrification in Garden lights, gate light etc. complete all as specified and as directed. |
| 142 | S&F of picture light of 12 Watts, 450/600 mm length metal body suitable for focus on Name plates/paintings, complete all as specifed and as directed. |
| 143 | S & F of LED post top lantern fitting powder coated aluminium die cast and spun aluminium with clear/opal diffuser 36 Watt including LED driver with gallary suitable for mounting on 32/40 mm GI pipe including necessary electric connections complete all as specified and as directed. |
| 144 | Supply and fixing of Wall Mounted Fan 400 mm sweep plastic body type including making all electric connections and depositing the old u/s to MES store yard complete all as directed. |
| 145 | Supply and Fix Cuboid ceiling fan 400 mm sweep remote controlled 3 blade. Make Halonix or equivalent make all as specified and directed by Engr-in-Charge. |
| 146 | S&F of instant heating Geyser 03 liter capacity vertical type with steel tank and glass inner linen complete including fasteners (02 No) for hanging and CP and PVC connection for inlet and outlet upto stop cock complete all as specified and as directed. |
| 147 | S & F installation of wall mounted electric chimney of size 90 cm,1200 Cum/Hrs, filterless auto clean with motion sensor technology, metallic blower and LED lamps suitable for four burners incl exhaust pipes of any length required at site to proper drain out of smoke complete all as specified and as directed. Make - Faber/Hindware/Elica/Glen. |
| 148 | Material and labour for earthing complete with GI earth plate electrode 600mm x 600mm x 6mm thick buried directly in ground not less than 2.25 mtrs below ground level with top edge of plate not less than 1.5 mtr deep below normal ground level connected to galvinised earth wire 4 mm by means of nuts, bolts and check nut to earth plate and to main board or DB including necessary PCC 1:2:4 type B-1 pit, cover frame , GI pipe 15 mm dia light grade for protection and GI pipe 20 mm dia medium grade for watering with funnel, wire mesh, salt and charcoal dust all over the plate all as specified and as directed. Please Enable Macros to View BoQ information |
| 149 | Material and labour for earthing complete with GI earth plate electrode 600mm x 600mm x 6mm thick buried directly in ground not less than 2.25 mtrs below ground level with top edge of plate not less than 1.5 mtr deep below normal ground level connected to galvinised earth wire 4 mm by means of nuts, bolts and check nut to earth plate and to main board or DB including necessary PCC 1:2:4 type B-1 pit, cover frame , GI pipe 15 mm dia light grade for protection and GI pipe 20 mm dia medium grade for watering with funnel, wire mesh, salt and charcoal dust all over the plate all as specified and as directed. Please Enable Macros to View BoQ information |
