|
| 1 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In Cement mortar. D.S.R No-15.7.4 |
| 2 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. D.S.R No-15.56 |
| 3 | Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: Asbestos cement sheet. D.S.R No-15.28.2 |
| 4 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5m as directed by engineer in charge 2.1.1 all kinds of soil. ( Dsr-2.1) |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:5:10 (1 cement : 5 coarse sand (zone-iii) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources).(D.S.R-4.1.10) |
| 6 | Brick work with common burnt clay F.P.S (non madular) brick of class designation 7.5 in foundation and plinth in ::cement mortar (1 cement :4 coarse sand ) dsr 6.1.1) |
| 7 | Brick work with common burnt clayF.P.S (non madular) brick of class designation 7.5 in superstructure above plinth level up to floor V level in all shape and sizes in ::cement mortar (1 cement :4 coarse sand ) dsr 6.4.1) |
| 8 | 15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 ( 1 cement 4 coarse sand). D.S.R No-13.5.1 |
| 9 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead. Of area 3 sq. metres and below(D.S.R No-15.12.1) |
| 10 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).salwood D.S.R No-9.1.2 |
| 11 | Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for hold fasts embedding hold fasts in cement concrete blocks of size 15x10x10 cm with cement concrete 1:3:6 ( 1 cement : 3 coarse sand: 6 graded stone aggregate 20 mm nominal size). painting two coats of approved wood preservation to sides of chowkhats and making good the damages to wall and floors as required complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-charge. Door chowkhats DSR No- 14.2.1 |
| 12 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) nondecorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws DSR 9.21.1 |
| 13 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes (weight not less than 10 kg per sqm) fixing with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. Second class teak wood 35 mm thick. (DSR No-9.9.1.1) |
| 14 | Providing and fixing wire gauge shutters using stainless steel wireguage (grade-304) apetuer 1:4 mm .50 mm dia wire for doors windows and clestory windows:35 mm thick shutter of required size UP teak wood (second class teak wood)D.S.R- 9.27.2.1 |
| 15 | Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete With second class teak wood beading 62X19 mm and barfi jali. . |
| 16 | supply and fixing of stainless steel door and fittings as sliding bolt ,tower bolt, handels etc complete as direcion of i/c. |
| 17 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting hoisting, fixing in position and applying a priming coat of approved steel primer all complete.(D.S.R No-10.2) |
| 18 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes.(D.S.R No-10.16.1) |
| 19 | Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer andtwo coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.1.00 mm thick with zinc coating not less than 275 gm/m² (D.S.R-12.1.1) |
| 20 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade old work(two or more coats applied @ 1.43 ltr/10sqm) over existing cement paint surface.(D.S.R- 13.112.1) |
| 21 | Providing and applying white cement based putty of average thicknes 1 mm of approved brand and manufacturer over the plastered wall surface to prepare the surface even and smooth complete. DSR No 13.80 |
| 22 | Painting with synthetic enamel paint of approved brand and manufacturer to give an even shade :one or more coats on old work (DSR-13.99.1) |
| 23 | Providing and fixing glass panes with putty and glazing clips in steel doors, windows, celestory windows, all complete with.5.0 mm thick glass panes (DSR-10.30.2) |
| 24 | Providing and fixing of kitchen shelves/cabinet with basket, shutter is made by mica laminated 18mm HDHMR board and back side of box is made by 12mmHDHMR board. Length and width of cabinet is 50cm and height of cabinet is 65cm including cost of all accessories such as handle, hinges, lock, channel, basket, catcher etc complete work with labour as per direction by E/I. |
| 25 | Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge. DSR-1.1.18 Please Enable Macros to View BoQ information |
