|
| 1 | Dismantling plain or corrugated steel sheeting, any gauge, thickness roof coverings incl ridge complete all as specified and as directed by Engineer-in-Charge. |
| 2 | M&L for Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as AZ 150 as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed by Engineer-in-Charge. |
| 3 | M&L Pre- painted galvalume aluminium zinc coating GI based Plain steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in ridges/ valley gutters, fixed with self tapping screw complete all as specified and as directed by Engineer-in-Charge. |
| 4 | S&F for two mm thickness Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc fixed with self tapping screws complete all as specified and as directed by Engineer-in-Charge. |
| 5 | M&L for galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with L-type or J-type or cranked hook bolts in lieu of screws , in roofs, walls etc. with grade of zinc coating 275 complete all as specified and as directed by Engineer-in-Charge. |
| 6 | Dismentling unframed timber scantlings 40 sq. cm and over in section, in any position complete all as specified and as directed by Engineer-in-Charge. |
| 7 | M&L for Mild steel work in tubular/channels/ angle.grider for trusses, purlins, vetical posts including special shaped washer, angle cleats, fish plates, gusset plates, base/ bearing plates, bolts and nuts etc. complete using ERW or induction butt welded tubes conforming to 1161-1979 grade st 240 Complete all as specified and directed by Engg-In- Charge. |
| 8 | M&L for preparation of new steel surfaces of any description over 10cm in width or girth not otherwise described and applying 2 coats of Synthetic enamel paint over a coat of red oxide primer, complete all as specified and as directed by Engineer-in-Charge. |
| 9 | Dismantling wall and ceiling board,of any description and incl old batterens complete all as specified and as directed by Engineer-in-Charge. |
| 10 | Supply & fixing inter locking metal grid (snap grid for false ceiling) of size 605 mm x 605 mm in true horizontal level, hot dipped galvanized steel sections (galvanized @ 120 grams/sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24 mm X 38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24 mm X 28 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200 mm x 600 mm and secondary cross “T” of length 600 mm and size 24 mm X 28 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200 mm X 600 mm panel to form grids of 600 mm X 600 mm and wall angle of size 24 mm X 24 mm X 0.4 mm. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 mm X 37 mm X 25 mm X 1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 mm X 30 mm X 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, 8 mm thick Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process complete all as specified and directed. |
| 11 | S & F hollow PVC panel joint type (with core, tongue) of 4 to 6 mm thick termite resistance, in approved colour golssy finish fixed with screws and incl battern for fame 300 C/C. Nails or adhesive on wooden/PVC/metal battens fixed on wall, complete all as specified and directed by Engr-in-Charge. |
| 12 | Demolition of exisiting damaged stone /Brick /Concrete Block masonary built in cement mortar including all quoins, arches, pillars etc complete all as specified and as directed by Engineer-in-Charge. |
| 13 | M&L for abour for random rubble stone masonary, uncoursed well bounded, bedded and soilidly hearted in cement mortar (1:4) completed all specified and directed by Engineer-in-Charge. |
| 14 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead complete all as specified and directed by Eng-in-Charge. |
| 15 | M&L rendering 15mm thick plaster on other than face fair face of brick work in CM 1:4 and surface finished even and fair complete all as specified. |
| 16 | M&L for rendering 15 mm thick cement mortar (1:6) on fair faces of stone masonary wall surfaces, complete all as specified and directed by Eng-in-Charge. |
| 17 | M&L for two coats of oil bound distemper on walls on newly plastered surfaces over 1 mm thickness wall care putty including preparation of surfaces by brooming or by steel wire brushing, complete all as specified by Engineer-in-Charge. |
| 18 | Preparation of new plaster surface of wall and applying two coat of cement base paint over a coat of primer complete all as specified. |
| 19 | Taking down chowkats or frames with shutters (without taking off shutters) of any description n exc 3 Sqm each all as specified and directed. |
| 20 | Supply and fixing aluminium work frame and shutters for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and paneling to be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) complete all as specified. |
| 21 | Supply and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness (weight not lessthan 10kg/sqm) complete all as specified. |
| 22 | Supply and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, and min wt 3kg/sqm with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment) complete all as specified. |
| 23 | M&L for PCC 1:2:4 type B1 (using 20 mm graded stone aggregates) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar parapets and railings, copings, kneelers, apex stones, bed plates, slightly rounded or chamfered angles and throating, as directe incuding necessary formwork required including in repair complete all as specified and as directed by EIC. Please Enable Macros to View BoQ information |
