|
| 1 | Dismantling tile work in floors and roofs laid in cement mortqr including stacking of serviceable material and disposal of unserviceable material within 50 meter lead : For thickness of tiles 25 mm to 40 mm. |
| 2 | Dismantling doors, windows and clearstory windows steel or wood shutter including chowkhats and holdfasts etc. complete and stacking within 50 meters lead : Of area exceeding 3 square meter. |
| 3 | Plaster on new surface on wall in cement sand mortar 1:3 including raking of joints etc. complete fine finish : 12 mm thick. |
| 4 | 6mm cement plaster to ceiling of mix 1:3 (1 Cement : 3 fine sand) |
| 5 | Cement concrete flooring grade 1:2:4 (1-Cement:2-Coarse sand:4-graded stone aggregate) rounding off edges etc. but excluding the cost of nosing of steps etc. complete : 75 mm thick with 20 mm thick nominal size aggregate. |
| 6 | Disnantling steel work in built up sections in angles, tees, flats, and channels etc. including dismembering and stacking within 50 meters lead. |
| 7 | Brick work in partition in super structure upto third storey 7cm. thick (brick on edges) using bricks of class designation 75 in : Cement mortar 1 : 3 (1 cement : 3 coarse sand) |
| 8 | Dismantling cement, asbestos, celotex or other hard board ceiling or partition walls including stacking of serviceable material and disposal of unserviceable material within 50 meter lead. |
| 9 | Structural steel work riveted or bolted in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete above plinth level up to 4.5 Mtr. height in R.S. joist flats, tees, angles and channels. |
| 10 | Providing & fixing anodizing alumium work (Anodizing to be got done from approved Anodizer) for doors, windows, ventilators and partition with extruded built up standard tubular and other sections of approved make confirming to IS : 733 and IS : 1285 anodised transparent 81 dyed to required shade according to IS : 1868 (Minimum anodic coating of grade AC 15), fixed with rawl plugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gas at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium section shall be smooth, rust free, straight, mitred and jointed mechanically wherever required inlcuding cleat angle Aluminum snap beading for glazing/paneling, C.P. Brass/ Stainless Steel screws, Al. Tower bolt & Al. handle & Al. Aldrop etc. all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and peneling to be paid for separately). |
| 11 | For Fixed portion |
| 12 | Providing and fixing Ist quality standard White Ivory Glazed Tiles ISI marked [IS:13753] of size 300mm x 200mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in white cement mixed with pigment to match the shade of tile complete (excluding the cost of cement plaster). |
| 13 | Providing and fixing Ist quality standard White Ivory Glazed Tiles ISI marked [IS:13753] of size 300mm x 200mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in white cement mixed with pigment to match the shade of tile complete (excluding the cost of cement plaster). |
| 14 | Size 300x450,300x600(as per direction of engineer in charge) |
| 15 | Polished Blue Kota Stone flooring skirting, laid over 20 mm thick base of C.M. 1:4 and jointed with grey cement slurry to match the shade of the slab including rubbing and polishing complete : For area of each slab up to 900 Sq. Cm : (A) 25 mm thick slab. |
| 16 | Providing corrugated G.I. Sheet roofing fixed with G.I. J or L hooks bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coat of approved paint on over lapping of sheet complete (upto a pitch of 600) & excluding the cost of purlins rafters and truses, for class of sheet : 0.63 MM thick |
| 17 | Painting with enamel paint of approved brand and manufacture to give an even shade: two or more coats on new work |
| 18 | Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes and including stacking of pipes within 50 meter lead : 15 mm to 40 mm nominal bore. |
| 19 | Dismantling of flushing cistern of any size including stacking of useful material near the site and disposal of unserviceable material within 50 meter lead. |
| 20 | Dismantling of C.I. sluice valve including stacking of useful materials within a lead of 50 meter: |
| 21 | Up to 150 mm dia. |
| 22 | Desmantling of floring with car including stacking of servceable material and diposal of unserviceable material with in 50 Mtr. Lead for Cement concrete flooring. |
| 23 | Applying white cement based putty over cement plaster surface for making even surface |
| 24 | P & F European type white glazed vitreous china Ist quality W.C. pan (IS:2556 Mark) with P or S trap including cutting and making good the wall and floor. |
| 25 | P & F water closet Seat Covers with brass hinges complete : |
| 26 | P&F C.P. lugs for toilet seat cover |
| 27 | P & F lst quality WVC Urinal (IS:2556 mark) with 25mm dia G.I. waste pipe, dome waste couplings, concealed iron brackets or screws etc complete. |
| 28 | Flat Back (large) or half stall size 610x400x80mm. |
| 29 | P & F Low level Flushing Cistern of 10 litres capacity (IS : 2556mark). Of approved make with complete fittings C.I. brackets duly painted, brass ball cock with ball, (IS: 1703 mark) complete including cutting and making good the wall: |
| 30 | PVC with CP brass long band. |
| 31 | PVC with PVC bend as per IS : 7231 . |
| 32 | P & F C.P. brass Urinal Spreader for stall urinal of approved make. |
| 33 | P & F WVC Wash basin (Ist quality IS:2556 Mark) of approved make with C.I. brackets duly painted 1 No. 15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste coupling of approved make 25 mm G.I. waste pipe complete including cutting & making good the wall : |
| 34 | Size 550 mm x 400 mm |
| 35 | P & F Bottle Trap of approved make : |
| 36 | C.P Brass 32 mm |
| 37 | P & F Bevelled edge Mirror/mirror with teak wood lipping around of special glass of approved make as per direction of Engineer-in-charge complete with 6mm thick commercial ply base fixed to wooden screws & washers. |
| 38 | Size 600 x 450mm x 4 mm thick |
| 39 | Providing and fixing Superior quality CP Brass fittings of approved make as per direction of Engineer-in-charge |
| 40 | Swan neck pillar cock 15 mm nominal size |
| 41 | Bib Cock with long thread 15 mm nominal size |
| 42 | Angular stop cock with long thread 15 mm nominal size |
| 43 | P & F G.I. pipes (Internal Work) with G.I. Fittings excluding union (IS:1239 Mark) & MS clamps including cutting and making good the walls and floors: |
| 44 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge. (Concealed work including cutting chases and making good the walsl etc) |
| 45 | CONCELED WORK INCLUDING CUTTING CHASES AND MAKING GOOD THE WALL ETC |
| 46 | 20 mm nominal outer dia pipes |
| 47 | 25 mm nominal outer dia pipes |
| 48 | 32 mm nominal outer dia pipes |
| 49 | P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.) approved quality /make including joining the pipe with solvent cement rubber ring and lubricant. |
| 50 | 75 mm dia |
| 51 | 110 mm dia |
| 52 | 160 mm dia |
| 53 | P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: |
| 54 | Coupler (socket) |
| 55 | 75mm dia |
| 56 | 110mm dia |
| 57 | Door tee |
| 58 | 75mm dia |
| 59 | 110mm dia |
| 60 | Bend 45 |
| 61 | 75mm dia |
| 62 | 110mm dia |
| 63 | Bend 87 .5 |
| 64 | 75mm dia |
| 65 | 110mm dia |
| 66 | Vent Cowel |
| 67 | 75mm dia |
| 68 | 110mm dia |
| 69 | Pipe clip |
| 70 | 75mm dia |
| 71 | 110mm dia |
| 72 | Supply and fixing 3.2mm thick 600 x 600mm anti static vinyi flooring as per sample approved by Enginner incharge . The flooring must be free pre-grooved for heat conforming to ASTM-F-1700 & ASTM-F-150 including making ground connection between static control flooring and external grounding system. Complete as required by Engineer Incharge |
| 73 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding: Old work (one or more coats) including scrapping surface and necessary repairs. Colour change |
| 74 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: Two or more coats on new work including preparation of base with primer, putty, lippy complete in all respect. |
| 75 | Repair to cement plaster in cement mortar 1:6 (1-Cement:6-fine sand) including removal of old plaster in regular shape and white or colour washing. |
| 76 | Providing and Laying Vitrified Porcelain dianomate floor tile, skirting dado , 10 cm thick flooring over 20 mm thick bed mortar 1:4 mix with 2-3 mm thick joint to be filled with cemutious grauter polymer based non shrine graute of metaling colour as per required of size.Flooring Tiles (600x600) |
| 77 | Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formal, dehydreresin in glue both sides with approved steel fittings complete as per Annexure ‘A’ Commercial Veneer both side 35 mm thick shutter |
| 78 | For External teak wood lipping on flush door 35 mm x 6 mm |
| 79 | Providing and fixing pressed steel mitred door frames manufactured from commercial mild steel sheet of 1.25 mm (16 gauge) thickness including hinges jamb, lock jamb, head and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.25 mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge. Profile 'C' |
| 80 | Painting with enamel paint of approved brand and manufacture to give an even shade: two or more coats on new work |
| 81 | Supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150 mm distance. |
| 82 | P&F expanded grill made of anodised aluminium as per desing and drawing having members section of size 7.5mm x 6.0mm and opening of size 102mm x 99mm to aluminium window/ vent with reqd. screws, Y and H aluminium sec (as per drawing) at the ends and middle joints respectively complete in all respect as per direction of engineer in charge. |
| 83 | Providing and fixing brass lock without handle for aluminium door, or approved quality, make & design as directed by Engineer inc harge |
| 84 | For shutters of doors, windows & ventilators incl. providing and fixing hinges/ rollers etc. and making provision for fixing of fittings wherever reqd. (lockes shall be paid for separately). |
| 85 | For shutters of sliding windows and making provision for fixing of fittings wherever required (lockes shall be paid for separately |
| 86 | S&F following sizes (dia.) of ISI marked medium duty PVC conduit along with accessories in surface / recessed using saddles, clamps, fastener as required including cutting the wall, covering conduit and making good the same as required.( Group-1) |
| 87 | 20 mm |
| 88 | 25 mm |
| 89 | 32 mm |
| 90 | Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with pigment to match the shade of the granite slab complete including rubbing and polishing of : Green / Black / Other granite |
| 91 | Above 3601 Cm2 Slabs |
| 92 | Extra for providing edge moulding to 18 mm thick marble stone counters, vantities etc. over item No. 7.1 & 7.2 including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. |
| 93 | Granite work. |
| 94 | Providing and Fixing 12mm thick prelaminated three layer medium density (exterior grade) particle bonded formaldehyde synthetic resin of approved brand and manufacture in paneling fixed in aluminium doors, windows/ stainless steel screws etc. complete as per architectural drawings and direction of engineer-in-charge. |
| 95 | Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side. |
| 96 | Providing and fixing glazing in aluminium door, window, vintilator shutters and partitions etc. with PVS/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge (Cost. of aluminium snap beading shall be paid in basic item.) |
| 97 | with glass panes of 5.0mm thickness (weight not less than 13.75 Kg/Sqm) as per IS : 2835 |
| 98 | P&F double action hydraulic floor spring of approved brand and manufacture to aluminium door shutter confirming to IS : 6315 incl. cost of cutting floors as reqd. embedding in floor and cover plate etc. complte as per direction of Engineer in charge. |
| 99 | This frame work is done for making existing wall surface in ensured level and for sticking the wall panelling sheet (panel) on it. The exact size of panel and correspondingly of the grid may be varied depending on the size of the wall. However it must ensured that a strip of 5 mm thick PVC sheet of width 75mm feathered at the edges shall be stuck at the places where two panels are jointed, using solvent. cement including all door fittings such as |
| 100 | L-drop, Handles, Locking bolts etc. as per approved of engineer in charge. |
| 101 | Providing and fixng False ceiling at all heights with Integral desified calcium Silicate reinforced with Fibre and natural filter false ceiling tiles of size 595x595 of approved texture , design and patterns as per CPWD specifications 2019 to be laid in true horizontal level ------- Complet |
| 102 | With 15 mm thick Tegular edged light weight calcium silicate false ceiling tiles. |
| 103 | Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formal dehyderesin in glue both sides with approved steel fittings complete as per annexure 'A' : 35 mm thick .Commercial Veneer both side |
| 104 | Brick masonry in foundation and plinth with bricks of class designation 75 in :Cement mortar 1 : 6 (1 cement : 6 coarse sand) Add extra over item No.5.1 for brick work in super structure upto third storey. Add extra over item of brick work with class designation 100 cement concrete bricks in substitution of class designation 75 : |
| 105 | Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finished: 20 mm thick. |
| 106 | Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finished: 12 mm thick. |
| 107 | Dismantling stone rubble masonry including stacking of serviceable material and disposal of unserviceable material within 50 meters lead. |
| 108 | In Cement mortar. |
| 109 | Structural steel work welded in built up sections, trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete above plinth level up to 4.5 Mtr. height in R.S. Joists flats, tees, angles and channels. |
| 110 | Providing corrugated G.I. Sheet roofing fixed with G.I. J or L hooks bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coat of approved paint on over lapping of sheet complete (upto a pitch of 600) & excluding the cost of purlins rafters and truses, for class of sheet : |
| 111 | 1.60 mm thick. |
| 112 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: Two or more coats on new work including preparation of base with primer, putty, lippy complete in all respect. |
| 113 | P & F G.I. Pipes (Internal work) with G.I. fittings (IS:1239 Mark) & M.S. clamps including cutting and making good the walls and floors : |
| 114 | 50mm dia nominal bore.- B class |
| 115 | Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) of approved make in surface / recessed ISI marked medium duty PVC conduit & it's accessories, round tiles,Hot Dipped Galvanized Modular Box with earth terminal, 6 A Modular switch,Modular plate with grid plate, screws, making connections, testing etc. as required. |
| 116 | Short point (up to 3 mtr.) |
| 117 | Medium point (up to 6 mtr.) |
| 118 | Long point (up to 10 mtr..) |
| 119 | Wiring of 3 pin 5 amp. Light plug point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) of approved make in surface / recessed ISI marked medium duty PVC conduit & it's accessories, Hot Dipped Galvanized M.S Modular box of 20 SWG with earth terminal, 6 A modular switch, 6 A modular socket, Modular plate with grid plate, screws, making connections, testing etc. as required. |
| 120 | On board |
| 121 | Supplying and fixing of power plug point Modular accessories on hot dipped galvanized modular on surface or in recessed with suitable size of grid plate with cover plate including cost of modular 16 amp. Switch and socket outlet , making connection , testing , etc. as required. |
| 122 | S&F following sizes (dia.) of ISI marked medium duty PVC conduit along with accessories in surface / recessed using saddles, clamps, fastener as required including cutting the wall, covering conduit and making good the same as required. |
| 123 | 20 mm |
| 124 | 25 mm |
| 125 | 32 mm |
| 126 | Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor ISI marked (IS:694) of 1.1 kV grade and approved make in existing surface or recessed conduit/casing capping including making connections etc. as required. |
| 127 | 2 x 2.5 sq. mm. + 1x1.5sqmm |
| 128 | 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. |
| 129 | 2 x 6.0 sq. mm. + 1 x 2.5 sq. mm. |
| 130 | P&F Recessed/ Surface mounting heavy duty horizontal type sheet steel Distribution board phophatised/ powder painted complete with suitable rating insulated copper bus bar, shorting link , neutral link, earth link and din bar,masking sheet, conforming to IS13032 & IS8623 including making internal DB terminations with copper lugs , testing etc. as required. |
| 131 | Double door (single phase) |
| 132 | 4 Way |
| 133 | 12 Way |
| 134 | P&F 240/415 V AC MCB with positive isolation of breaking capacity not less than 10 KA (B/ C/ D tripping characteristic) ISI marked IS 8828(1996)]/ conforming to IEC 60898 in existing board/sheets including making connections, testing etc. as required. |
| 135 | Single pole MCB |
| 136 | 6 A to 32 A rating |
| 137 | Double pole MCB |
| 138 | 40 A 63 A rating |
| 139 | P & F heavy duty, Double ball bearing and with sturdy mesh guard; Aluminium alloy one piece blade wall mounting oscillating type air circulator conforming to IS:2997, including fixing with anchor bolts, regulator making connection testing etc. as required. |
| 140 | 450 mm sweep With three speed regulator |
| 141 | P&F of IP 65 Protected high power LED flood light system with Pressure diecast aluminium housing toughened glass diffuser with suitable lenses on LED to achieve various beam angles 240 volt ,50 HZ of high Power LED Fixture supplied with pre wired cable of 1 mtr. Integrated driver shall be high efficiency having efficiency more than 85% and in compliance to IEC standard BIS certified |
| 142 | High Power LED Flood Light 150 Watt |
| 143 | P&F of IP 65 Protected LED Street light Luminare on Existing Bracket Fixture made of Powder Coated Single piece Pressure die Cast aluminium with heat dissipation fins on housing with UV Stablizerd PC / Toughened Glass Cover |
| 144 | LED Street light Fixture 100 watt |
| 145 | S & F of Street light bracket made out from following size of ' B ' class GI pipe with heavy duty pole clamp, Saddles suitable fastners etc. as required. |
| 146 | 32 mm Dia. |
| 147 | P & F following size hot dip galvanized M.S. box of 20 SWG with earthing terminal in recess/ surface suitable for modular accessories as required. |
| 148 | 8 Module |
| 149 | 10/ 12 Module |
| 150 | P/Laying P.V.C. / XLPE insulated & P.V.C. sheathed cable of 1.1 KV grade with aluminium conductor of IS:1554 P-I / IS :7098 P - I of Group 1 of approved make in ground as per IS:1255 including excavation of 30cmx75cm size trench, 25 cm thick under layer of sand,IInd class bricks covering, refilling earth,compaction of earth, making necessary connection, testing etc. as required of size. 10.0 Sq.mm |
| 151 | 2 core |
| 152 | Providing and fixing of IP 65 protectd Polycarbonate / Polysterene fuse box moulded with inside knock outs of following size with hinged cover, transparent window, PU gasket, locking arrangement, duly holded with 2 nos. pole clamps of 20 mm x 3 mm flat with nut and bolts, complete with The box shall be provided with Din rail, 4 / 8 way 10.0 / 16.0 sq.mm heavy duty connector, earth terminal, complete in all respect. |
| 153 | 125 mm X 200 mm X 122 mm |
| 154 | Maintenance free Gel Earthing with Pipe in pipe / Pipe in strip technology filled with anti corrosive conductive compound ( CPRI Tested ) below the ground in 150 - 200 mm dia. earth pit & surrounding filled with required mineral filling compound ( MFC should have hygroscopic property to retain the moisture for long time to create low resistance zone ) and C.C. finished chamber covered with hinged type with locking arrangement C.I. Cover, C.I. Frame of size 300mm x 300mm complete testing of earth resistance as required. of following sizes. |
| 155 | GI pipe 3000 mm long, 50 / 25mm, Terminal 14 mm GI Strip |
| 156 | S & Laying following size earth wire/strip in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection etc. as required. |
| 157 | 8 SWG copper Wire |
| 158 | SITC of radial / mixed flow submersible motor pump sets ISI marked (IS:8034-1989) of approved make with required accessories including making connection suitable for T.W./ D.C.B./ Open well. The job includes lowering of riser pipe, G.I./ H.D.P.E. pipe with rope, cables, installation of complete fitting and accessories, jointing of electrical cables up to switch board. All labour for testing of submersible pumps set and supply of water to water mains, complete in all respect. 100 mm diameter Submersible pump shall have following HP Rating, phase, Head, minimum Discharge respectively. 5.0 HP, 1-Ø, (120-220)Mtr, (100-38)LPM |
| 159 | Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) of approved make in surface / recessed ISI marked medium duty PVC conduit & it's accessories, round tiles,Hot Dipped Galvanized Modular Box with earth terminal, 6 A Modular switch,Modular plate with grid plate, screws, making connections, testing etc. as required. |
| 160 | Short point (up to 3 mtr.) |
| 161 | Medium point (up to 6 mtr.) |
| 162 | Long point (up to 10 mtr..) |
| 163 | Wiring of twin control light point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) of approved make in surface / recessed ISI marked medium duty PVC conduit & it's accessories, round tles, Hot Dipped Galvanized M.S Modular box of 20 SWG with earth terminal,6 A two way Modular switch, Modular plate with grid plate, screws, making connections, testing etc. as required. |
| 164 | Long point (up to 10 mtr..) |
| 165 | Wiring of 3 pin 5 amp. Light plug point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) of approved make in surface / recessed ISI marked medium duty PVC conduit & it's accessories, Hot Dipped Galvanized M.S Modular box of 20 SWG with earth terminal, 6 A modular switch, 6 A modular socket, Modular plate with grid plate, screws, making connections, testing etc. as required. |
| 166 | On board |
| 167 | Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor ISI marked (IS:694) of 1.1 kV grade and approved make in existing surface or recessed conduit/casing capping including making connections etc. as required. |
| 168 | 3 X 1.5 sqmm |
| 169 | 2 x 2.5 sq. mm. + 1x1.5sqmm |
| 170 | 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. |
| 171 | 2 x 6.0 sq. mm. + 1 x 2.5 sq. mm. |
| 172 | Supplying and fixing of power plug point Modular accessories on hot dipped galvanized modular on surface or in recessed with suitable size of grid plate with cover plate including cost of modular 16 amp. Switch and socket outlet , making connection , testing , etc. as required. |
| 173 | P&F 240/415 V AC MCB with positive isolation of breaking capacity not less than 10 KA (B/ C/ D tripping characteristic) ISI marked IS 8828(1996)]/ conforming to IEC 60898 in existing board/sheets including making connections, testing etc. as required. |
| 174 | single pole MCB. : |
| 175 | 6 A to 32 A rating |
| 176 | Double pole MCB |
| 177 | 6 A to 32 A rating |
| 178 | Triple pole MCB |
| 179 | 40 A 63 A rating |
| 180 | P&F Recessed/ Surface mounting heavy duty horizontal type sheet steel Distribution board phophatised/ powder painted complete with suitable rating insulated copper bus bar, shorting link , neutral link, earth link and din bar,masking sheet, conforming to IS13032 & IS8623 including making internal DB terminations with copper lugs , testing etc. as required. |
| 181 | Double door (single phase) |
| 182 | 8 Way |
| 183 | Double door (Three phase) |
| 184 | 8 Way |
| 185 | P&F recessed/ surface mounting heavy duty Vertical type 16 SWG sheet steel Distribution board with provision of incomer suitable for MCB / RCCB and SP / TP MCB as outgoing , phophatised ,powder painted complete with insulated suitable rating copper bus bar , neutral link, earth link and din bar, masking sheet,conforming to IS13032 & IS8623 including making internal DB terminations with copper lugs , testing etc. as required. |
| 186 | Double door with Provision of Incomer MCCB 200/ 250 A Rating |
| 187 | 6 Way |
| 188 | P & F following modular accessories made out of unbreakable and fire retardant poly carbonate with silver contacts including making connections testing etc. as required |
| 189 | 5 step fan regulator 2 Module |
| 190 | P & F ISI marked single tone electronic call bell including making connection testing etc. as required. |
| 191 | SITC of quick make and quick break 4 POLE current limiting MCCB having following current rating, short circuit breaking capacity at 440/415 V, 50 Hz; O/L & S/C settings and conforming to IS 60947-2 / IEC 60947-2 with front face and centralised adjustable, line load interchangeability, having positive isolation capability, provision for UVR , shunt trip ,earth fault trip, push ( test ) to trip , including making connections with lugs & spreaders, etc. as required. |
| 192 | With Thermal Magnetic release |
| 193 | With Microprocessor based release |
| 194 | 250 Amp , 35 kA, adjustable O/L & Adjustable S/C setting, Ics = 100 % Icu |
| 195 | P/Laying P.V.C. / XLPE insulated & P.V.C. sheathed cable of 1.1 KV grade with aluminium conductor of IS:1554 P-I / IS :7098 P - I of Group 1 of approved make in ground as per IS:1255 including excavation of 30cmx75cm size trench, 25 cm thick under layer of sand,IInd class bricks covering, refilling earth,compaction of earth, making necessary connection, testing etc. as required of size.( Armoured). |
| 196 | 10.0 Sq.mm |
| 197 | 4 core |
| 198 | 16.0 Sq.mm |
| 199 | 4 core |
| 200 | Supplying and making one end termination with heavy duty single compression brass gland SIBG type, heavy duty aluminium lugs duly crimped with crimping tool, PVC tape etc for following size of Armoured PVC insulated & PVC sheathed/ XLPE aluminium conductor cable of 1100 volt grade as required of size. |
| 201 | 4 x 10.0 sq.mm |
| 202 | 4 x 16.0 sq.mm |
| 203 | Plate Earthing as per IS:3043 with G.I. Earth plate of size 600mm x 600mm x 6.0mm by embodying 3 to 4 mtr. below the ground level with 25 mm dia. G.I. 'B' class watering Pipe including all accessories like nut, bolts, reducer ,nipple, wire meshed funnel, and C.C. finished chamber covered with hinged type with locking arrangement C.I. Cover, C.I. Frame of size300mm x 300mm complete with alternate layers of salt and coke/charcoal, testing of earth resistance as required. |
| 204 | S & Laying following size earth wire/strip in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection etc. as required. |
| 205 | 25mm x 3mm G.I. ( Hot Dipped ) Strip |
| 206 | P & F Star rated double ball bearing capacitor start, aluminium body & blade ceiling fan with down rod up to 30 cm with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. |
| 207 | 1200 mm Sweep 5 Star rated |
| 208 | P & F 18 swg M.S. Recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mm length extended on each side . |
| 209 | P & F of ventilating fans, Capacitor start, single phase with PVC impeller, ABS body, automatic openable louver shutter in existing opening including making connection, testing etc. as required. |
| 210 | 250 mm sweep |
| 211 | P&F of Heavy duty capacitor start, Double ball bearing 900/1400 RPM single phase ISI marked Exhaust fan,IS:2312 marked in existing opening including making connections testing etc. as required. |
| 212 | 450 mm sweep(900/1400 RPM) |
| 213 | P & F of Gravity Louver shutter of superior quality made out of PVC including cost of nuts, bolts, etc as reqd. |
| 214 | Up to 380 mm size |
| 215 | P & F of IP20 surface/recess mounted LED downlight made of pressure diecast aluminium housing, with heat sink and good quality reflector, high efficiency external driver, power consumption 14/15 watt, system lumen efficiency >80 lumen/watt. CCT 6000K (minimum) K, CRI >80, PF >0.9 life time 50,000 burning hours. |
| 216 | P & F of IP 20 LED tube light 20 watt with external batten made from CRCA sheet steel suitable to replace T-8/T-12 tube light, integral driver, 2000 luman + 5% tolerance system luman efficiacy of 100 Lm/ watt minimum expected life time of 25000 burning hours, CCT 5700 K, ANSI, CRI 80, driver efficiency >85%, Life expectancy of driver min 30000 hrs. PF 0.95 at full load/ 230 volt AC. |
| 217 | P & F of 4 star rated vertical storage water heater with outer casing made of M.S.sheet finished with anti-corrosive powder coating,inner tank made of pure electrolytic copper/stainless steel / SPHP, Tubular copper sheathed and Nickel plated heating element/ twin ceremic cartridge heating element, stem type thermostat and thermal cut out,Dual indicating lamps for power supply and thermostat,PUF insulation, Pressure relase valve,fusible plug etc. as required held in position with 4 no. rack bolts,duly wired with 3 core 2.5/4.0 Sqmm PVC insulated & sheathed copper conductor and 16 A/25A three pin plug top,including making inlet,outlet heavy gauge C.P./ Flexible alloy connection,testing etc. as required. |
| 218 | 15 Ltr. Please Enable Macros to View BoQ information |
