|
| 1 | Toilet Construction |
| 2 | 2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil |
| 3 | 10.2:Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 4 | OD352338/2025-2026:Providing and fixing Aluminium profile sheets (size, shape and pitch of corrugationas approved by Engineer-in-charge) 0.460 mm or nearest available thickness. The sheet shall be fixed usingself drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to sizeand shape wherever required. |
| 5 | OD352335/2025-2026::Providing and fixing rain water gutter semi circular section using 150mm dia 6kgfPVC pipe including fitting with 32x5mm flat supporting at 1m intervals complete as per the direction ofengineer in charge at site |
| 6 | 50.18.9.19.2:Providing and fixing PVC pipes including fixing the pipe with clamps/clips at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 m dia 4 Kgf/cm2 - External work - Exposed on wall |
| 7 | 10.28:Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) |
| 8 | OD352337/2025-2026:Designing, fabricating,testing and installing Curtain Wall with Aluminium CompositePanel Cladding, with open grooves for linear as well as curvilinear portions of thebuilding , for all heightsand all levels etc. including: Providing, fabricating and supplying and fixing panels of aluminium composite panelcladding INCLUDINGaluminium base frame work in pan shape in metalic colour of approved shades madeout of 3mm thickaluminium composite panel material. The aluminium composite panel cladding sheetshall be coil coated,with Kynar 500based PVDF / Lumiflon based fluoropolymer resin coating ofapproved colour and shade onface # 1 and polymer (Service) coating on face # 2 as specified using stainless steelscrews, nuts, bolts,washers, cleats, weather silicone sealant, backer rods etc.with aluminium compositepanel cladding till thehanding over of the building for occupation. The Contractor shall provide curtain wallwith aluminiumcomposite panel cladding, having all the performance characteristics all complete, asper the Architecturaldrawings, as per item description, as specified, as per theapproved shop drawings andas directed by theEngineer-in-Charge.However, for the purpose of payment, only the actual area on theexternal face of thecurtain wall with Aluminum Composite Panel Cladding (including width of groove)shall be measured in sqm.up to two decimal places. |
| 9 | OD352336/2025-2026:Supply and fixing 3D Acrylic letters ENGLISH LETTERS 25-30cm or MALAYALAM LETTERS 20-25cm for name board etc.. complete as per direction of Engineer in charge at site. |
| 10 | OD352339/2025-2026:Supplying and fixing in place Granite Name board of slab area less than 0.9sqmincluding engraving and painting letters etc.. complete as per direction of Engineer in charge at site |
| 11 | 4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III)derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 12 | 10.25.2:Item Shifted to Sub head 14 as item 14.73Item Shifted to head 14 as item 14.74Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 13 | 50.6.2.1:Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x15 cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 15cm in: CM 1:6 ( 1 cement :6 coarse sand) etc complete |
| 14 | 13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) |
| 15 | OD374399/2025-2026:Providing and laying 60 mm thick factory made cement concrete interlocking paverblock of M - 30 grade made by block making machine with strong vibratory compaction, of approved size,design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of stoneaggregate, etc. all complete as per the direction of Engineer-in-charge. OD 80/21-2 |
| 16 | OD402213/2025-2026:Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specification excluding appropriate priming coat, preparation of surface, etc. complete.On steel work |
| 17 | 11.41.2:Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm. |
| 18 | 8.31:Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in- Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 19 | 8.2.2.2:Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm Please Enable Macros to View BoQ information |
