|
| 1 | Demolishing RCC work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead ALL as per direction of Engineer-in-Charge. |
| 2 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 Mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns, sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-Charge, the sheet shall be fixed using self drilling / self tapping screws of size (5.5 x 55 mm) with EPDM seal, complete upto any pitch in horizontal / vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required complete all as specified and as directed. |
| 3 | Providing and fixing precoated galvanised steel sheet Gutter (600 mm over all girth) thickness 0.50mm (+0.05 %) total coated thickness, zinc coating 120 grams per sqm as per IS: 277, in 240 Mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling / self tapping screws complete with strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and as directed.NOTE :- Work shall be executed at a height upto 16 Mtr including all necessary scaffolding. |
| 4 | Material and labour for two coats of painting to steel / wall work with Deluxe Multi Surface Paint to give an even shade, two or more coats applied @ 0.90 ltr / 10 sqm over an under coat of primer applied @ 0.80 ltr / 10 sqm of approved brand and manufacture complete all as specified and as directed. |
| 5 | Providing and fixing powder coated aluminium, minimum thickness of powder coating 50 micron aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber / neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, CP brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.NOTE :- Glazing, paneling and dash fasteners shall be measured and paid separately. |
| 6 | Providing and fixing 4mm thick float glass panes of weight not less than 10kg / sqm, as in glazing of aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and as per the directions of Engineer-in-Charge.NOTE :- Cost of aluminium snap beading shall be paid separately in relevant BOQ item. |
| 7 | Material and labour for 30mm thick Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished, including cement slurry, but excluding the cost of nosing of steps etc. complete all as specified and as directed. |
| 8 | Material and labour for double charged vitrified floor tiles of size 600mm x 600mm x10mm thick with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid over and including 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg / sqm including grouting the joints with white cement and matching pigments etc complete all as specified and as directed. |
| 9 | All as per Ser item No 8.00 above but as in skirting including 12mm thick screed bed in CM (1:3) complete all as specified and as directed. |
| 10 | Material and labour for 15mm thick plaster in CM (1:4) on fair faces of walls, finishing the surfaces even and smooth without using extra cement complete all as specified and as directed. |
| 11 | Material and labour for finishing walls with 100% premium acrylic external emulsion paint having VOC less than 50 gm / litre and UV resistance as per IS 15489:2004, alkali and fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives on new surfaces with two or more coats applied @ 1.43 litre / 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm complete all as directed. |
| 12 | Material and labour for 10mm thick internal plaster in CM (1:6) on other than fair faces of walls and as directed by Engineer-in-Charge.. |
| 13 | Material and labour for distempering with oil bound washable distemper of approved, shade, brand and manufacture to give an even shade on new work with two or more coats over and including water thinnable priming coat over 2mm thick wall care putty including complete finishing of putty by using sand papers and as directed by Engineer-in-Charge. |
| 14 | Material and labour for steel work (hot finished welded type tubes) as in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete all as specified and as directed. |
| 15 | Material and labour for TMT Thermo-Mechanically Treated bars of grade Fe-500D or more reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level and as directed by Engineer-in-Charge. |
| 16 | Reinforced cement concrete work as in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window cills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (Zone-III) derived from natural sources : 3 graded stone aggregate 20mm nominal size derived from natural sources) complete all as specified and as directed. |
| 17 | Material and labour for formwork to lintels, beams, plinth beams, girders, bressumers and cantilevers complete all as specified and as directed. |
| 18 | Material and labour for Pre-cast cement concrete block masonry 1:2:4 using 20mm graded stone aggregate, type B1 with solid blocks, exc. 10 cm in width and setting in mortar(1:6) complete all as specified and as directed. |
| 19 | Dismantling C.I. or asbestos / PVC rain water pipe 110mm dia pipe with fittings and clamps including stacking the material within 50 metres lead and as directed by Engineer-in-Charge. |
| 20 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 type A, including jointing with seal ring conforming to IS : 5382, leaving 10mm gap for thermal expansion, single socketed pipes 110 mm diameter complete all as specified and as directed. |
| 21 | Providing and fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592, type A, including jointing with seal ring conforming to IS : 5382, leaving 10mm gap for thermal expansion for 110 mm bend complete all as specified and as directed. |
| 22 | All as per Ser item No 21.00 above but shoe for 110mm dia pipe. |
| 23 | Material and labour for 12mm thick Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side, Grade I, Type II IS: 12823 marked fixing in aluminum/wooden partion with Rubber / screw and as directed by Engineer-in-Charge. |
| 24 | Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer-in-Charge (Nominal concrete 1:3:6 or richer mix equivalent design mix complete all as specified and as directed.. |
| 25 | Material and labour for 1:2:4 (1 cement : 2 coarse sand (Zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources) complete all as specified and as directed by Engineer-in-Charge.. |
| 26 | Material and labour for steel work welded in built up sections / framed work / square bars framed work, including cutting, hoisting, fixing in position In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works and applying a priming coat of approved steel primer using structural steel etc. complete all as specified and as directed by Engineer-in-Charge. |
| 27 | Material and labour for finishing walls with 100% premium acrylic external emulsion paint having VOC less than 50 gm / litre and UV resistance as per IS 15489:2004, alkali and fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives on old surfaces with two or more coats applied @ 1.43 litre / 10 sqm complete all as directed. |
| 28 | Removing demolished material from defence land to a distance exc.5.00 KM but n exc. 15 KM and depositing as per site arrangement of contractor complete all as specified and as directed. |
| 29 | Material and labour for 75mm thick Plain Cement Concrete, (1:3:6), type C-2, using 40 mm graded crushed stone aggregate as in plinth protection finished even and fair complete all as specified and as directed. |
| 30 | Material and labour for 5mm thick plaster in CM (1:4) , as in ceiling, finishing the surfaces even and smooth with out using extra cement complete all as specified and as directed. |
| 31 | Material and labour for preparation of plastered or unplastered surface and distempering two coats with oil bound washable distemper of approved shade, brand and manufacture to give an even shade over and including water thinnable priming coat with cement primer complete all as specified and as directed by Engineer-in-Charge. |
| 32 | All as per ser Item No. 31 above but on old surfaces after and including complete removal of existing treatment of any type and condition complete all as specified and as directed by Engineer-in-Charge. |
| 33 | Material and labour for preparing new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed. |
| 34 | Material and labour for preparing old ceiling surfaces and applying two coats of white wash complete all as specified and as directed. |
| 35 | Material and labour for painting steel surfaces with synthetic enamel paint of approved shade, brand and manufacture to give an even shade of two or more coats on new work / old surface complete all as specified and as directed. |
| 36 | Material and labour for preparation of old / new wooden surfaces painting with synthetic enamel paint of approved shade, brand and manufacture to give an even shade : one or more coats on old work complete all as specified and as directed. |
| 37 | Dismantling floor tiles, wall tiles in cement mortar including stacking material within 50 metres lead for thickness of tiles 10 mm to 25 mm for vertical surface complete all as specified and as directed. |
| 38 | Material and labour for 25mm thick cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished, including cement slurry, but excluding the cost of nosing of steps etc. complete all as specified and as directed. |
| 39 | Providing and laying ceramic glazed floor tiles of size 300 x 300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except white, ivory, grey, fume red brown, laid over and including 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete all as specified and as directed. |
| 40 | Providing and fixing 1st quality coloured glazed ceramic tiles of size 450mm x 300mm / 450mm x 350mm , in dado/skirting etc. conforming to IS : 15622 (thickness to be specified by the manufacturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over and including 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete all as specified and as directed. |
| 41 | Providing and fixing chequerred precast cement concrete tiles 300 x 300mm x 22-25 mm thick as in footpath and court yard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, over and including 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand), light shade pigment using white cement complete all as specified and as directed. |
| 42 | Material and labour for formwork to soffits of suspended floors, roofs, landings, balconies and access platform complete all as specified and as directed. |
| 43 | Material and labour for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n.exc. 20cm wide and sides of RCC / PCC bands in walls, horizontal or sloping and similar work exc. 10 cm but n.exc. 20cm wide complete all as specified and as directed. |
| 44 | Material and labour for 18-20mm thick Granite stone slab colour black, Cherry/Ruby red gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, steps, floor etc and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. at all levels complete all as specified and as directed. |
| 45 | Labour for providing edge moulding to 18 mm thick Granite stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. |
| 46 | Providing and fixing 0.63mm thick corrugated G.S. sheet roofing including vertical / horizontal / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal / vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required complete all as specified and as directed.NOTE :- Work shall be executed at a height up to 12 to 15 Mtr, factory type bldg / hangar. |
| 47 | Providing and fixing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with 0.63 mm thick with zinc coating not less than 275 gm/m² polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete all as specified and as directed. |
| 48 | Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed. |
| 49 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead complete all as specified and as directed. |
| 50 | Material and labour for preparation of old wooden surfaces Painting with synthetic enamel paint of approved, shade, brand and manufacture to give an even shade, two or more coats on old work complete all as specified and as directed. |
| 51 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead of area 3 sq. metres and below each complete all as specified and as directed. |
| 52 | Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-Charge. |
| 53 | Providing and fixing pressed steel door frames conforming to IS: 4351, Profile B fixing with adjustable lugs with split end tail to each jamb manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-Charge. |
| 54 | Material and labour for 35mm thick factory made 2nd class hard wood rail and style, plain framed, panelled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered partical board with commercial veneering on both sides, the size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and as directed. |
| 55 | Providing and fixing PVC door frame of size 50 x 47 mm with a wall thickness of 5 mm (± 0.2 mm), made out of single piece extruded PVC profile, with mitred cut joints and joint with 2 nos of PVC bracket of size 190 mm x 100 mm long arms of cross section size 35 x 15 mm and self driven self taping screws, the vertical door profiles to be reinforced with 40 x 20 mm M.S. rectangular tube of 0.8 mm, including providing EPDM rubber gasket weather seal throughout the frame, including jointing 5 mm PVC frame strip with PVC solvent cement on the back of the profile. The door frame to be fixed to the wall using 8 x100 mm long anchor fasteners complete, all as per manufacturer's specification and direction of Engineer-in-Charge. |
| 56 | Material and labour for 35 mm thick factory made Solid panel PVC Door shutter, Decorative finish (wood grained finish) made out of single piece extruded solid PVC profiles, 5 mm (± 0.2 mm) thick, having styles & rails (except lock rail) of size 95 mmx 35 mm x 5 mm, out of which 75 mm shall be flat and 20 mm shall be tapered (on both side), having one side thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power, including reinforcing with MS tube of size 40 mm X 20 mm x 1 mm, joints of styles & rails to be mitered cut & joint with the help of PVC solvent cement, self driven self tapping screws & M.S. rectangular pipes bracket of size 190 mm X 100 mm of cross section size 35 mm x 17 mm x 1 mm at each corner. Single piece extruded 5 mm thick solid PVC Lock rail of size 115 mm x 35 mm, out of which 75 mm to be flat and 20 mm to be tapered at both ends, having 15 mm solid core in middle of rail section integrally extruded, fixing the styles & rails with the help of solvent and self driven self tapping screws of 125 mm x 11 mm, including providing 5 mm Single piece solid PVC extruded sheet inserted in the door as panel, all complete as per manufacturer's specification and direction of Engineer-in-Charge. |
| 57 | Providing and fixing aluminium tower bolts, 150mm x 10mm dia ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete all as specified and as directed. |
| 58 | Supply and fix Anodised Aluminium butt hinges 100mm complete all as specified and as directed. |
| 59 | Providing and fixing 125mm aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete all as specified and as directed. |
| 60 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete size 250 x 16mm complete all as specified and as directed. |
| 61 | Supply and fix in repair providing and fixing uplasticised PVC connection pipe with brass unions 15mm nominal bore 45cm long complete all as specified and as directed. |
| 62 | Supply and fix in repairs inlet mouth of Nahni trap / drain PTMT (an Engineering Thermoplastic) grating round 100 mm dia with a height of 8 mm and weighing not less than 75-100 gms complete all as specified and as directed. |
| 63 | Dismantling 15 to 40mm dia G.I. pipe including stacking of dismantled pipes (within 50 metres lead) as per direction of Engineer-in-Charge. |
| 64 | Steel water tubing medium grade 15mm bore galvanized with all fittings and fixed to walls and ceiling or laid in floors including cutting chases where required complete all as specified and as directed. |
| 65 | All as per Ser item No 64 above but of size of 20mm bore |
| 66 | Supply and fix in repairs 15mm dia CP cast copper alloy bib tap with flange, ISI marked (Prayag catalogue no PIS-06 or equivalent) complete all as specified and as directed. |
| 67 | Providing and fixing in repairs C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931, 15mm nominal bore complete all as specified and as directed. |
| 68 | Supply and fix in repairs CP health Faucets (1m tube and Hook) complete all as specified and as directed. |
| 69 | Providing and fixing in repairs white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required (W.C. pan with ISI marked white solid plastic seat and lid) complete all as specified and as directed. |
| 70 | Supply and fix in repairs Vitreous China urinals, bowl type (back or corner wall type),complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) all as per manufacturers specification and direction of Engineer-in-Charge. |
| 71 | Providing and fixing in repairs counter top China Wash basin size 520 x 310 x 170mm mm with C.P. brass pillar tap with 32mm C.P. brass coupling and waste pipe of standard pattern complete all as specified and as directed by Engineer-in-Charge.MAKE :- Prayag catalogue item no 4709 or techno commercially equivalent models of makes specified in PS. |
| 72 | Demolishing brick work manually / by mechanical means in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge. |
| 73 | Material and labour for modular bricks work with common burnt clay machine moulded perforated bricks of class designation 12.5 conforming to IS : 2222 in superstructure above plinth level up to floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) complete all as specified and as directed. |
| 74 | Material and labour for Plain Cement Concrete, (1:2:4), (1 Cement : 2 coarse sand (Zone-III) derived from natural sources : 4 graded stone aggregate 40 mm nominal size derived from natural sources) as in hard standing including necessary demolition all as directed by Engineer-in-Charge. |
| 75 | Material and labour for Plain Cement Concrete 1:3:6 type C2 using 20mm graded stone aggregate as in surface channels and drains complete all as specified and as directed. |
| 76 | Extra for forming fair finished drain or channel upto 55 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred / stopped ends etc. complete all as specified and as directed. |
| 77 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 type A, including jointing with seal ring conforming to IS : 5382, leaving 10mm gap for thermal expansion, single socketed pipes 150 mm diameter complete all as specified and as directed. |
| 78 | Providing and fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592, type A, including jointing with seal ring conforming to IS : 5382, leaving 10mm gap for thermal expansion for 150 mm bend complete all as specified and as directed. |
| 79 | All as per Ser item No 78.00 above but shoe for 150mm dia pipe. |
| 80 | Material and labour for water proofing treatment to the sunken portion with following steps :-(i) removing of exiting treatment including cleaning with wire brush.(ii) 15mm thick plaster in CM 1:3 including using of WPC as per manufactureres instructions along entire perimeter of sunken portion. (iii) Applying two coats of brush bond of FOSROC company or equivalent, second coat will be applied after complete drying of first coat or after 24 hours.(iv) Sunken floor shall be kept ponded with water for minimum 48 hours.(v) Providing one 450mm long 32 mm dia spout pipe of CPVC and to slope. NOTE : - BRUSH BOND must be applied as per manufacturer's instructions. |
| 81 | Material and labour for Plain Cement Concrete (1:5:10), type E-2, using 40mm graded crushed stone aggregate as in sunken slab filling etc., complete all as specified and as directed. |
| 82 | Material and labour for Plain Cement Concrete (1:2:4), type B-1, 30mm thick using 20mm graded stone aggregate as in flooring finished fair and even complete all as specified and as directed. |
| 83 | Material and labour for one coat of distempering of 1st quality acrylic distemper of approved brand and manufacture over one coat of primer to give an even shade on old surface including 1mm thick wall care putty complete all as specified and as directed by Engineer-in-Charge.NOTE :- Complete removal of old surface to be carried out by using broom / wire brush etc and complete finishing of putty by using sand papers. |
| 84 | All as per Ser item No 83.00 above but on old surfaces of walls. |
| 85 | Supply and fix in repair toilet paper holder (C.P. brass) complete all as specified and as directed by Engineer-in-Charge. |
| 86 | Supply and fix in repair Brass chromium plated tubular towel rail, 20mm dia, D type, 60 cm long between flanges, fixed in repair complete all as specified and as directed. |
| 87 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls White Vitreous China Wash basin size 550 x 400mm with a pair of 15mm C.P. brass pillar tap complete all as specified and as directed. |
| 88 | Material and labour for point wiring complete with 1.5 sq.mm single core PVC insulated but unsheathed multi stranded copper conductor FRLSH cable 1100 Volts grade drawn through and including non metallic rigid PVC heavy duty concealed conduit (minimum 25 mm dia external) but shall be increased as per actual site requirement in accordance with clause 19.125 of SSR part- I, ISI marked with wall thickness not less than 1.8 mm including conduit accessories like bends, tees, junction boxes etc fixed surface/ concealed/ recessed in wall or ceiling etc including 1.5 sq.mm PVC insulated but unsheathed multi stranded copper conductor FRLSH cable as earth continuity wire including modular type metal flush box with cover plate and frame of required module for mounting of modular switches, sockets, switch sockets, fan regulators with required modules all as specified etc for one light point controlled by one, one way switch 5 Amps. |
| 89 | All as per Sl Item No. 88 here in before but one ceiling fan point / wall fan / exhaust fan point controlled by one, one way switch 5 Amps and regulator. |
| 90 | Material and labour for sub main wiring single core, PVC insulated, unsheathed, multi stranded copper conductor cable, 1100 Volts, FRLSH Grade, ISI marked, drawn through and including suitable PVC non metallic rigid conduit with accessories fixed on walls / roofs / floors / ceiling etc. and connecting terminal ends including one run of single core, PVC insulated, unsheathed, multi stranded copper conductor cable, green in colour, 1100 volts, FRLSH grade as earth continuity conductor consisting of 2 x 1.5 sq. mm + 1 x 1.5 sq. mm earth wire complete all as specified and as directed.NOTE :- Two runs of 2.5 sq.mm copper cable, one run of earth wire of 1.5 sq.mm copper cable and 25mm dia PVC conduit shall be measured and paid as one RM. |
| 91 | All as per Sl Item No. 90 here in before but 2 x 2.5 sq. mm + 1 x 2.5 sq. mm earth wire NOTE :- Two runs of 2.5 sq.mm copper cable, one run of earth wire of 2.5 sq.mm copper cable and 25mm dia PVC conduit shall be measured and paid as one RM. |
| 92 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 Amps modular socket outlet and 5/6 A modular switch, including connections etc as required complete all as specified and as directed. |
| 93 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 and 15/16 Amps modular socket outlet and 15/16 A modular switch, including connections etc as required complete all as specified and as directed. |
| 94 | Supplying and fixing 3 terminal, 5A ceiling rose on the existing junction box / wooden block including connections etc as required complete all as specified and as directed. |
| 95 | Supply and fix LED batten luminaire not less than 20 watt fitting 4’ long with white powder coated housing & frame in CRCA sheet, high efficiency LED grade diffuser, electronic driver duly wired upto terminal block CRI>80, LED colour temperature -5700k, IP-20, 50000 burning hours as per L70 criteria, ambient temperature – 0 to 50 Deg C, Driver efficiency >85%, THD<10%, PF>0.95, sure protection in CM-3KV, multistage isolated constant current, constant voltage operated driver with range 150-270V AC and safety extra low voltage safe level<60V DC as per IEC standard including batten/suspension system complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and as directed. |
| 96 | Supply and fix of industrial air circulator fan 450mm sweep, AC, single phase 230 / 240 volts fixed on wall complete with fixing arrangements like clamps / nut and bolts accessories including connecting with suitable size of copper flexible wire complete all as specified and as directed. |
| 97 | Supply and fix exhaust fan, heavy duty with metallic body 300mm sweep complete with louvers shutters, 230 / 240 volts, 1400 RPM including making hole in stone masonary wall and finishing the same with plastering etc including making connections with of flexible copper wire from ceiling rose to fan complete all as specified and as directed. |
| 98 | Supply and laying of 2 x1.5 sq.mm fire alarm armoured cable, 600/1000 volts rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of cross linkable Ehtylene Propylene Rubber (EPR) insulation and LSZH inner bedding XLPE insulation, steel wire armouring and LSZH outer sheath drawn in PVC conduit complete all as specified and as directed. |
| 99 | Supply and fixing addressable type multi Sensor detector with heat and smoke with built-in LED and mounting base complete with all connections etc as required complete all as specified and as directed. |
| 100 | Supply and fixing addressable control module complete all as specified and as directed. |
| 101 | Supply and fixing fire alarm sounders / sirens electronic type horizontal single stage continuous normal operation for at least 50 minutes with sound level 65 dBA to 120dBA measured at 3.0 mtr with audible annunciation and 75 cd flashing at 1Hz for visual indication complete all as specified and as directed. |
| 102 | Supply and fixing addressable manual call point resettable type complete all as specified and as directed. |
| 103 | Supply, installation, testing and commissioning of microprocessor based intelligent addressable main fire alarm panel central processing unit with 2 loop to 4 loop modules and capable of supporting not less than 240 devices ( including detectors ) and minimum 120 detector per loop and loop length 2 Km, network communication card, minimum 320 character graphics / LCD display with touch screen or other keypad minimum 4000 events history log in the non volatile memory (EPROM), power supply unit ( 230 +/-5%, 50 Hz) 48 hrs back up with 24 volts sealed maintenance free batteries with automatic charger, the panel shall have facility to connect printer to print out log and facility to have seamless integration with analog / digital voice evacuation system ( which is part of the schedule of work under SH PA system ) and shall be complete with all accessories, the panel shall be compatible for IBSM system with open protocol BAC net /Modbus over IP complete as specification complete all as specified and as directed. |
| 104 | Supplying and fixing 8 way, double door, single pole and neutral, sheet steel, MCB distribution board, 240V, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, inter connections, power painted including earthing etc as required complete all as specified and as directed. |
| 105 | Supplying and fixing SPN 32A rating 240/415 V, 10KA 'C' curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete testing and commissioning etc as required complete all as specified and as directed. |
| 106 | Supplying and fixing SP 5A to 32A rating 240/415 V, 10KA 'C' curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete testing and commissioning etc as required complete all as specified and as directed. |
| 107 | Supply and fix UPS for 30 min backup single phase AC input 160 to 260V and out put 230 +1% of capacity 01 KVA complete all as specified and as directed. |
| 108 | Material and labour point wiring complete with 1.5 sq.mm single core PVC insulated but unsheathed multistranded copper conductor FRLS cable 1100 Volts grade drawn through and including non metallic rigid PVC heavy duty concealed conduit (minimum 20 mm dia external) but shall be increased as per actual site requirement in accordance with clause 19.125 of SSR part- I, ISI marked with wall thickness not less than 1.8 mm including conduit accessories like bends, tees, junction boxes etc fixed surface/ concealed/ recessed in wall or ceiling etc including 1.5 sq.mm PVC insulated but unsheathed multistranded copper conductor FRLS cable as earth continuity wire including modular type metal flush box with cover plate and frame of required module for mounting of modular switches, sockets, switch sockets, fan regulators with required modules all as specified etc for One Light / Fan Point controlled by One Switch complete all as specified. |
| 109 | Supply and fixing exhaust fan made of plastic body complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 200mm including making hole all as specified and all as directed by Engr in charge. |
| 110 | Supply and fix exhaust fans Steel body of size 300 mm sweep with AC single phase 230/ 240 V ,speed 1400 RPM with complete louver fixed in out side with making a hole in the wall as required at site with all fixing arrangment at reqd at site complete finishing work complete with all connections all as specified and directed by Engr-in charge. |
| 111 | Supply and fixing of Round recess mounted LED edge lit slim downlight with die-cast aluminium housing finished in premium white powder coating plastic diffuser makes it a robust LED lighting suitable of size 15 watt fixing in wall /roof with complete electric connection including taking down old one complete all as specified and as directed. |
| 112 | Supply and fixing of square surface mounted mounted LED 1x1' suitable of size 24 watt fixing in with complete electric connection including taking down old one complete all as specified and as directed. |
| 113 | Supply and fixing Recess mounted 2' x 2' LED fitting full lit luminaire with glare free uniform illumination with longer life suitable for 36 watt of including all fixing arrangements and taking down of old un serviceable complete all as specified and as directed. |
| 114 | Supply and fixing LED batten 10 watt high quality materials and design extruded aluminium housing enhances safety with high quality PC diffuser polycarbonate housing incl all fixing arrangement and taking down of old un serviceable complete all as specified and directed. |
| 115 | Supply and\ fixing LED batten 20 watt high quality materials and design extruded aluminium housing enhances safety with high quality PC diffuser polycarbonate housing including all fixing arrangement and taking down of old un serviceable complete all as specified and directed.. |
| 116 | Supply and fixing of surface mounted LED 1x4' suitable of size 36/40 watt with high performance, fixing in with complete electric connection including taking down old un serviceable one complete all as specified and as directed by Engr-in-charge. |
| 117 | Supply and fxing of recess mounted LED 1x4' ceiling light suitable of size 36/40 watt with high performance, fixing in with complete electric connections including taking down old one complete all as specified and as directed. |
| 118 | Supply and fixing ceiling fans complete with blades , down rods, electronic regulator and accessories, 230 V, 1200 mm sweep 39 watt, RPM 280 min air delivery 245 CMM with service value 6.00 BEE five star rated with brushless direct current motor and all remaining accessories including regulator, safety pin, nut bolts, washers, including provn for roof hanging hook of suitable size for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete all as specified and as directed by Engr-in-charge.. Please Enable Macros to View BoQ information |
