|
| 1 | Demolition of cement concrete unreinforced of any description and in any position, not otherwise specifically provided for and Material and Labour for cement concrete 1:2:4 type B-0, using 12.5mm graded stone aggregates for filleting, benching, slightly rounding or chamfering on edges, filling undulations / depressions in roof surface, providing concrete platform for tanks wherever required complete all as specified and directed. |
| 2 | Taking down / removing existing water proofing treatment from RCC roof slab including removal of plaster bed below felt / membrane and disposal of the same to distance exceeding 50mtr but not exceeding 100mtr as and where directed and Material and Labour for 10 mm thick screeding / rendering in cement mortar 1:3 on concrete roof surface, using Water Proofing Compound @ 3% by weight of cement, surface finished even and smooth without using extra cement complete all as specified and directed.Note: Water Proofing Compound shall be measured and paid separately. |
| 3 | Supply only intergral water proofing compound. |
| 4 | Material and Labour for Cutting out cracks to \\"V\\" section in existing roofs or terracing, cleaning out wetting grouting with cement and sand slurry 1:3 complete all as specified and directed. |
| 5 | Material and Labour for cleaning the plastered /concrete surface with wire brush and applying water proofing treatment as under:-(a) Apply a uniform coat of primer at 0.70 kg/sqm over cement plaster. (b) 3 mm thick and weighing not less than 3.6 kg/sqm Atactic Polypropylene Polymer (APP) modified bitumen - based prefabricated five layer water proofing membrane reinforced with non woven polyester matt black finished over compatible primer at 0.40 Ltr/sqm of density at 25 degree centigrade 0.87 to 0.89 kg/litre and viscosity 70 to160 cps or cold sticker and torch application of membrane with 10 cm overlap both ways after necessary preparation of surface complete as per manufacturers instructions. (c) Apply two coats of bitumastic - aluminium paint over the membrane. |
| 6 | Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level ) completeall as specified and directed |
| 7 | Material and Labour for waterproofing treatment to RCC sunken slab complete all as specified and directed as under. Make: PIDILITE , Dr Fixit or equivalent.(a) Clean the sunken portion of toilet/Bath/WC/Kitchen thoroughly to remove laitance, dirt, dust etc (b) Form angle fillet of size 40 mm x 40mm along the junction of wall and floor using polymer modified mortar (\\"Dr Fixit\\" Pidicrete URP\\" or equivalent)(c) Sanitary pipes entering through walls and floor shall be sealed with \\" Dr Fixit Bathseal Tape\\" and the gaps to be grouted with non-shrink cementitous grout \\" Dr Fixit Bathseal Gruot\\" or eqvt . Nahani traps , etc to be fitted securely and the gaps around it to grouted in the same manner.(d) Apply one coat of a Bitumen- modified polymer coating \\" Dr Fixit Bathseal Plus\\" or eqvt on all angle fillets by brush and cover it with 100mm open woven mesh when it is still wet. Apply second coat of the same coating on the angle fillets and allow it to dry completely.(e) After completing plumbing work in the toilet/WC/Bath/Kitchen floor, tiling work (floor and dado) can be carried out using suitable Tile Adhesives and ready to make tile grouts of Approved makes such as Dr Fixit, FOSROC , SIKA, MC BUCHEMIE, ROFF etc , all as specified and directed.(Note:- Tiling work will be measured and paid separately).(f) After 2 to 3 days, sunken portion must be overlaid with a 50mm thick concrete screed M 15 type B0 mixed with integral WPC (Liquid) laid to slope 1:60 towards outer face of wall. Provide 40mm OD UPVC pipe at the lowest point with 300mm projection beyond the outer face of the wall. Then fill up the sunken portion with lean concrete 1:5:10 type E2, complete all as specified and directed.(g) After completing plumbing work in the toilet/WC/Bath/Kitchen floor, tiling work (floor and dado) can be carried out using suitable Tile Adhesives and ready to make tile grouts of appd makes such as Dr Fixit, FOSROC , SIKA, MC BUCHEMIE, ROFF etc , complete all as specified and directed.(Note:- Tiling work will be measured and paid separately) |
| 8 | Material and Labour PCC (1:5:10) type E2 using 40mm graded stone aggregate as in mass concrete or as in sunken portion or floor complete all as specified & directed |
| 9 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing coat) complete all as specified and directed. |
| 10 | Material and Labour 25 mm thick PCC 1 :2 : 4 type B1 ( Using 20mm graded stone aggregate ) as in base of floors complete all as specified and as directed by Engineer-in-Charge. |
| 11 | Material and Labour for Non Skid ceramic tiles 7mm to 8mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick in CM (1:6) Screed bed or bedding layer of mortar for laying floor finishes complete all as specified and directed. |
| 12 | Ditto all as in item No.11 above but as in skirting /dados including 10mm thick rendering in CM 1:4 complete all as specified and directed. |
| 13 | Material and Labour for Non Skid ceramic tiles 7mm to 8mm thick (square/rectangular) area of each tile not exceeding 0.11sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick in CM (1:6) Screed bed or bedding layer of mortar for laying floor finishes complete all as specified and directed. |
| 14 | Material and Labour Coloured Glazed ceramic tiles 450 mm X 300 mm X 7 mm thick, on vertical surfaces such as skirting, dados and risers to steps etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match including 10mm thick rendering in CM 1:4 complete all as specified and directed. |
| 15 | Demolition of brick work or stone masonry or block masonry built in cement or cement/lime mortar complete all as specified and directed. |
| 16 | Material and Labour for PCC solid block masonry of blocks of type C1 (20mm graded stone aggregate) (1:3:6) wall exceeding 10cm in width & built in CM (1:6) complete all as specified and directed. |
| 17 | Material and Labour for 20mm to 25mm thick machine cut cuddappah stoneas in slab flooring over cement screed bed laid and jointed with grey cment slurry mixed with pigment to match the shade of the slab including grinding polishing laid and including over 15 mm thick screed in CM 1:6 complete all as specified and directed. |
| 18 | Demolition of old stone slab of any description complete all as specified and directed. |
| 19 | Material and Labour for 20mm thick Granite slab machine cut in laid over cement screed and jointed with grey cement slurry and pointed with whiteor colour cement with admixture of pigment to match the shade of granite stone including cutting and polishing complete including screed bed 15mm thick in CM 1:4 complete all as specified and directed. |
| 20 | Material and Labour for 20mm thick Granite slab machine cut in dado/skirting over cement screed and jointed with grey cement slurry and pointed with whiteor colour cement with admixture of pigment to match the shade of granite stone including cutting and polishing complete including rendering of 10mm thick in CM 1:4 complete all as specified and directed. |
| 21 | Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed. |
| 22 | Material and Labour machine cut kota stone slab flooring 20mm to 25mm thick in flooring but one piece as in treads of straircase etc over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete, over and including15 mm thick screed bed or bedding in CM 1:6 for laying floor finishes complete all as specified and directed. |
| 23 | All as item No 22 here in before but in skirting but one piece for step riser over and incl 10 mm thick rendering in CM 1:4 to receive kota stone/slab etc complete all as specified and directed. |
| 24 | Taking down cement or cement lime plaster on brick or stone walls,ceilings etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. |
| 25 | Material and Labour for 15 mm thick plastering in cement mortar 1:4 on external plaster finished the surfaces (upto 10 mtr height) using 3% of WPC of weight of cement used or as per manufacturer instruction complete all as specified and directed.(WPC shall be measured and paid seperatly). |
| 26 | Material and Labour for preparation to new surface and applying finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed. |
| 27 | Material and Labour for complete removal of existing treatment, preparing the surfaces and applying finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed. |
| 28 | ditto all as in item No. 25 above but 10mm thick in CM 1:4 finished even & smooth with thin layer of sagol finish but as in ceiling complete all as specified and directed. |
| 29 | Material and Labour for applying three coat of white wash on ceiling including preparation of new surfaces complete all as specified and directed. |
| 30 | Material and Labour for applying one coat of white wash on celing on old surfaces including preparation of old surfaces including cleaning smoke efflorocense of any type or spot of nail filled with putty complete match to old surface complete all as specified and directed. |
| 31 | Material and Labour for 15 mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces including finishing the surface with a thin layer of sagol complete all as specified and directed. |
| 32 | Material and Labour preperation of new plastered surfaces & applying two coats of oil bound distember over a coat of alkali resistant primer on wall complete all as specified and directed. |
| 33 | Material and Labour for complete removal of existing finishes and applying two coats of oil bound distemper on walls over a coat of alkali resistant primer including chalk whiting preparation of old surfaces , on plastered surfaces prepratary to distempering complete all as specified and directed. |
| 34 | Material and Labour for preparation of new surfaces of wall and applying three coats of white wash on walls complete all as specified and directed. |
| 35 | Material and Labour for complete removal of existing finishes and applying three coats of white wash on walls including preparation of old surfaces complete all as specified and directed. |
| 36 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.50sqm but n. exc 4.00 sqm complete all as specified and directed. |
| 37 | Supply and Fixing Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed. |
| 38 | Material and Labour For Plain cement concrete 1:2:4 type B0, (12.5 mm graded aggregate) in door and windows frames, any size, single or double rebated, including arrangement for fixing of hinges and fixtures as required complete all as specified and directed. |
| 39 | Material and Labour for flush shutters 35mm thick solid core constructions with block board core , ply wood face panels commercial type on both side complete all as specified and directed. |
| 40 | Supplied and fitted to chowkats 35 mm thick second class Hard wood factory made Gauzed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (a); complete all as specified and directed. |
| 41 | Supply and Fixing Aluminium, anodised, barrel tower bolts of extruded section 200 mm long complete all as specified and directed. |
| 42 | Supply and Fixing Aluminium handles, cast type, anodised size 150 mm long complete all as specified and directed. |
| 43 | Supply and Fixing 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed. |
| 44 | Supply and Fixing in repair Mild steel Butt hinges100 mm long, medium weight, cold rolled steel complete all as specified and directed. |
| 45 | Material and Labour for applying two coats of synthetic enamel paint over a coat of pink primer on new wooden surfaces of width or girth exceeding 10 cm including preparation of surfaces complete all as specified and directed. |
| 46 | Material and Labour for applying one coats of synthetic enamel paint on old wooden surfaces of width or girth exceeding 10 cm including preparation of surfaces complete all as specified and directed. |
| 47 | Taking down shutter from frame exc 1sqm and n.exc 2 Sqm each and removing from the site complete all as specified and directed. |
| 48 | Supply and Fixing Solid PVC door frame of size 50mm X47 mm made out of 5mm thick plain colour PVC sheet rinforced with MS Square tube suppling and fixing in opening as per specification and drawing complete all as specified and directed. |
| 49 | Supply and Fixing MS Butt hinges 75 mm long, medium weight, cold rolled steel complete all as specified and directed. |
| 50 | Supplying and Fixing Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip if 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bootom rail on either side & as gap insert for top rail and bottom rail ; Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles. & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site as per specification & drawing Complete all as specified and directed. |
| 51 | Supply and Fixing Aluminium, anodised, barrel tower bolts of extruded section 125mm long complete all as specified and directed. |
| 52 | Supply and Fixing Aluminium handles, cast type, anodised size 125 mm long Complete all as specified and directed. |
| 53 | Taking down chowkat without taking off shutter from frame n.exc 1.5 sqm each Complete all as specified and directed. |
| 54 | Supply and Fixing Powder coated aluminium window sliding type (3 track) with frame size100mmx35mmx1.2mm and shutter 39.40mmx17.70mmx1.2mm with and including two glass shutter & one wire mesh shutter incl necessary jointing cleats, glazing clips, rubber packing, powder coated aluminium snap beading screws with and including 4mm plain float glass & 0.36 mm nominal dia SS wire mesh and 1.40mm avg width of aperture fittings etc Complete all as specified and directed. |
| 55 | Supply and Fixing galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm fixing to new steel window with nut bolt,fixed complete all as specified and directed. |
| 56 | Supply and Fixing Powder coated aluminium louvered ventilators of section size 100mmx25mmx1.50mm including frosted glass 4mm thick fixed in half portion & adjustable type louvers in another half and including stainless steel wire mesh 0.36mm nominal dia SS wire mesh and 1.40mm avg width of aperture fixed type on outside frame etc. complete all as specified and directed by Engr-in-Charge. |
| 57 | Supply and Fixing mild steel work in framed work such as grills framed guard bars, gratings, ladders etc with ends of bars shouldered and / or riveted or forged into spikes and similar work. Fe 290 code E-165 complete all as specified and directed. |
| 58 | Material and Labour for preparation of new steel surfaces exc 10 cm width or girth and applying one coats of synthetic enameled paint complete all as specified and directed. |
| 59 | Supply and Fixing in repairs powder coated aluminuium pipe 20 mm dia as in curtain rod fixed to brackets complete all as specified and directed.Note-brakets shall be measured and paid separately. |
| 60 | Supply and Fixing in repairs powder coated aluminium brakets fancy type for curtain rods of 20mm dia complete all as specified and directed. |
| 61 | Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth complete all as specified and directed. |
| 62 | Taking up or down 15 mm bore steel tubing and connections including disconnection of fittings and cleaning for refixing where required complete all as specified and directed. |
| 63 | Ditto-all as above Item No. 62 but 20 mm dia pipe etc. |
| 64 | Supply and Fixing 15 mm bore of pipe medium grade steel tubes, galvanised with & including all fittings and fixed complete to concealed walls and ceilings or laid in floors complete all as specified and directed. |
| 65 | All as per serial item No. 64 above but except steel tubing. |
| 66 | Supply and Fixing 20 mm bore of pipe medium grade steel tubes, galvanised with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed. |
| 67 | Supply and Fixing in repair rotational moulded polyethylene water storage tanks of capacity 500 ltr hoisted and fixed in position including 25mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed complete all as specified and directed. |
| 68 | Supply and Fixing Gun-metal, globe or gate valves 15mm bore, with iron wheel head, screwed both end for iron pipe and fixed in repair complete all as specified and directed. |
| 69 | Supply and Fixing in repairs 20mm dia bore Gun metal, globe or gate valves with Iron wheel head, screwed both ends for Iron pipes and fixed complete all as specified and directed. |
| 70 | Supply and Fixing in repair angle stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unionSupply and Fixingixed - bore dia of pipe 15 mm complete all as specified and directed. |
| 71 | Supply and Fixing in repair stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unionSupply and Fixingixed - bore dia of pipe 15 mm but fancy type with long shank and cup ( concealed type) complete all as specified and directed by Engineer in Charge. |
| 72 | Supply and Fixing in repairs 15mm dia fancy type Bib taps, cast copper alloy CP with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. |
| 73 | Supply and Fixing in repair,Chromium plated shower roses with or without swivel joints, 125mm size, including fixing to steel pipe or union complete all as specified and directed. |
| 74 | Supply and Fixing PVC connections 15 mm size with PTMT nuts of 600 mm long complete all as specified and directed. |
| 75 | Supply and Fixing in repair PVC (SWR) pipes 110mm dia ,single socketed in any length with rubber ring joints laid in trenches or floor complete complete all as specified and directed. |
| 76 | Supply and Fixing in repairPVC (SWR) pipes 110mm dia ,single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed. |
| 77 | Supply and Fixing in repair,PVC (SWR) pipes 75 mm dia ,single socketed in any length with rubber ring joints fixed and laid in trenches or floor complete all as specified and directed. |
| 78 | Supply and Fixing in repair,PVC (SWR) pipes 75 mm dia ,single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed. |
| 79 | Supply and Fixing in repair,PVC (SWR) bends any radius,for 110mm dia pipe complete all as specified and directed. |
| 80 | Supply and Fixing in repair,PVC (SWR) bends any radius, 75mm dia pipe complete all as specified and directed. |
| 81 | Supply and Fixing in repair,PVC (SWR) branch piece, single (single Y) equal or unequal,for 110mm dia pipe complete all as specified and directed. |
| 82 | Supply and Fixing in repair,PVC (SWR) branch piece, single (single Y) equal or unequal,for 75mm dia pipe complete all as specified and directed. |
| 83 | Supply and Fixingin repair,PVC (SWR), junction single, (Single T) equal or unequal,for 110mm dia pipe complete all as specified and directed. |
| 84 | Supply and Fixing in repair,PVC (SWR), junction single, (Single T) equal or unequal,75mm dia pipe complete all as specified and directed. |
| 85 | Supply and Fixing in repairs Vitreous China Squatting pan Orissa pattern long pan, size 580 mmX440mm white with `P' or `S' trap, front or back inlet and foot rests any pattern including connection to trap and to flushing pipe, anti-syphonage pipe etc., including trap set in and including concrete complete including making good to floor complete all as specified and directed. |
| 86 | Supply and Fixing in repair PVC valveless syphonic action type flushing cistern (Low or high level) of 10 litre capacity, coloured with inlet ball valve, float, handle including fixing brackets and 32 mm bore PVC flush pipe etc complete all as specified and directed. |
| 87 | Supply and Fixing in repairs vitreous china wash basin white, flat back of size 450mm x 300mm, excluding taps, waste chain & plug & porcelein stopper but including brackets, cutting for and pinning in ends of brackets complete all as specified and directed. |
| 88 | Supply and Fixing in repair 15mm dia pillar taps fancy type cast copper alloy with capestan heads chromiun plated screwed down high pressure with hot &cold with long screwed shanks and fly nuts complete all as specified and directed. |
| 89 | Supply and Fixing in repairs for 600mm x 450mm bevelled edge mirror of selected quality glass,mounted on 6mm thich AC Building board or commercial plywood and fixed to wooden plugs with chromium plated brass screw and cup washers complete all as specified and directed. |
| 90 | Supply and Fixing 20mm dia or over pre polished and moulded granite corner shelf fixed in CM 1:3 to wall and maked good with putty filling with colour match to existing surface complete all as specified and directed by EIC. |
| 91 | Supply and Fixing in repairs tubular towel rail 20mm dia, D type 60cm long between flanges brass chromium plated complete all as specified and directed. |
| 92 | Material and Labour 75 mm dia cast iron floors trap with grating including jointing to waste pipe fixed in cement concrete1:2:4 type B1 complete all as specified and directed. |
| 93 | Material and Labour for PCC 1:3:6 type C-2 , 75 mm thick as in plinth protection complete all as specified and directed. |
| 94 | Material and Labour for 75mm thick PCC 1:4:8 type D2 ( 40 mm graded stone aggregates) as in sub base of floor complete all as specified and directed. |
| 95 | Material and Labour for Prepolished Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigment including 20mm thick screed bed in CM 1:6 complete all as specified and directed. |
| 96 | Supply and Fixing II class hardwood plain solid straight chowkats and frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and directed. |
| 97 | Supply and Fixing in repairs 12mm thick Veneered decorative plywood grade 1(with BWR resin) with only one face has decorative veneer & other side balancing white lamination fixed with screws to timber frame complete all as specified and directed. |
| 98 | Supply and Fixing in repair Contineous Piano hinge 30mm width of flaps (when open), mild steel, bright finish or electrogalvanised complete all as specified and directed. |
| 99 | Supply and Fixing Hasp and staple 150mm long, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and directed. |
| 100 | Supply and Fixing 75mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed. |
| 101 | Supply and Fixing 100mm long Aluminium handles, cast type, anodised complete all as specified and directed. |
| 102 | Supply and Fixing in repairs grating square or circular 125mm dia of PTMT (minimum weight 100 gms, complete all as specified and directed. |
| 103 | Excavation in trenches not exceeding 1.50mtr wide and 1.50mtr depth for foundation, etc., for Shaft wells, Manholes etc not exceeding 10sqm on plan and not exceeding 1.50mtr in depth and getting out in soft / loose soil complete all as specified and directed. |
| 104 | All as per Item No 103 above, but for depth exceeding 1.5mtr and not exceeding 3.0 mtr in soft/loose soil. |
| 105 | Returning filling in including spreading leveling watering well ramming in layers not exceeding 25cm thick with soil obtained from excavation complete all as specified and directed. |
| 106 | Removing excavated surplus soil not exceeding 50mtr and depositing where directed at a level exceeding 1.5m above the starting point complete all as specified and directed. |
| 107 | Demolition and breaking up drain pipes of 150 mm bore RCC/SGSW set in cement mortar including removing the debries to a distance n exc 100mtr,where directed complete all as specified and directed. |
| 108 | All as per item No. 108 above but dia of pipe 200mm. |
| 109 | Material and Labour for PCC M-7.5 grade nominal mix using 40 mm graded stone aggregate as in concrete bed to drain pipes including packing under and haunching against sides of pipes with concrete after they are laid and bedded dia of pipe 150mm complete all as specified and directed. |
| 110 | All as per item No. 110 above but dia of pipe 200mm. |
| 111 | Material and Labour for 150mm dia RCC drain pipes class NP2 laid in trenches and jointed with in cement mortar complete all as specified and directed. |
| 112 | All as per item No. 110 above but dia of pipe 200mm. |
| 113 | Material and Labour cutting to existing manholes for connecting new drain, making good to pipe and rendering, cutting out existing benchings for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1, using 20mm graded stone aggregate, smooth finished and reforming benching as required for internal dia of pipe 150mm complete all as specified and directed. |
| 114 | Supply and Fixing RCC precast Sewage manhole cover MD grade of size 450mmx900mm thickness 25mm to 30 mm and set the same at the site including removing old from site in any position complete all as specified and directed by EIC |
| 115 | Supply and Fixing RCC Precast round Sewage manhole cover MD Grade of size 560mmx600mm dia thickness 50mm to 60 mm heavy duty and set the same at the site including removing old from site in any position complete all as specified and directed by EIC |
| 116 | Dismantling wrought iron or mild steel work of any description not othervise provided for |
| 117 | Supply and Fixing in repairs 15mm dia brass CP Wall mixer for mixing hot & cold water screwed down for iron pipe and fixed of make CERA cat part No F 2010403 or techno commercially equivalent models in makes complete all as specified and directed. |
| 118 | Supply and Fixing plate rack made of stainless steel 1mm thick and overall size 750mmx600mmx250mm securing with nails or screw in wall of any description complete all as specified and directed. |
| 119 | Supply and Fixing in repairs PVC waste outlet pipe for 32/40mm dia WHB / Sink complete all as specified and directed. |
| 120 | Supply and Fixing in repairs 32 mm bore waste fittings, brass, chromium plated for sinks, basins etc with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete. |
| 121 | Supply and Fixing in repair ,stainless steel sink with drainage board, 1mm thick, kitchen or laboratory with plugs, washers and waste; including PVC waste pipe, bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. |
| 122 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixtures and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors etc complete all as specified and directed. |
| 123 | Material and Labour for point wiring complete with 1.5 Sqmm single core FRLS PVC insulated unsheathed cable 1100 V grade multi stranded copper conductor drawn through non metallic rigid PVC conduit and accessories concealed in walls/ceilings including 1.5 Sqmm dia multistranded copper cable as earth continuity conductor connected to common earth dolly, including 1.22 mm thick pressed steel terminal boxes to provision of Modular switches to house switch/regulators etc including Modular Plate and Covers for one fan/light /bell point controlled by one switch/bell push complete all as specified and directed. |
| 124 | All as per item No 123 above but for one 3 pin 5 Amps socket on same board controll with other switches on same board complete all as specified and directed. |
| 125 | All as per item No 123 above but for one 3 pin 5 Amps socket on independent board complete all as specified and directed. |
| 126 | All as per item No 123 above but for one light point controlled by two way switch complete all as specified and directed. |
| 127 | All as per Item No 123 here-in- before but with 2.5 Sqmm PVC insulated multistranded copper conductor with 2.5 sqmm cable as earth continuity conductor for Power Socket on independent board on the existing Concealed conduit complete all as specified and directed. |
| 128 | All as per Item No 123 here-in- before but with 4 Sqmm PVC insulated multistranded copper conductor with 4 sqmm cable as earth continuity conductor for Power Socket/AC/Geysers on independent board on the existing Concealed conduit complete all as specified and directed. |
| 129 | Supply and fix modular switch 1 way 6A 1 module complete all as specified and directed. |
| 130 | Supply and fix modular switch 2 way 6A 1 module complete all as specified and directed. |
| 131 | Supply and fix modular bell push 6A 1 module complete all as specified and directed. |
| 132 | Supply and fix modular socket 6A 2/3 pin combined 2 module complete all as specified and directed. |
| 133 | Supply and fix modular socket 16A 2/3 pin combined 2 module complete all as specified and directed. |
| 134 | Supply and fix modular switch 1way 16A 1 module complete all as specified and directed. |
| 135 | Supply and fix Modular fan regulator complete all as specified and directed. |
| 136 | Supply and fix electric bell Ding Dong, AC 230 volts complete all as specified and directed. |
| 137 | Supply and fix ceiling rose surface bakelite with three terminals complete all as specified and directed. |
| 138 | Supply & fix in repair LED fitting for Bldg security, 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65 / 66 protection complete. including conncting with suitable size of copper condector flexible cable from fitting connector to ceiling rose and fix on wall with clamps & nut bolts and necessary GI bracket made of 32 mm light grade GI pipe of 1 mtr lenth with necessary bending complete all as specified and directed . |
| 139 | Supply and fixing in repair LED lights fitting 1x 20W, 220V,AC, decorative box type with driver, holder incl LED tybe light connecting up with suitable size of flexible copper conductor cable from ceiling rose complete all as specified and directed. |
| 140 | Supply and Fixing in repair wall/ceiling mounted LED tube light fitting in repairs Energy efficient high quality invertor batten having Lithium ion battery of 3.7V, 19 WH for backup upto 2Hrs with high power brightness having BIS certification, LED fitting should be LM 80 certified with system efficacy greater than 100 lumens/watt, including LED tube 20/22 watt having colour temperature 6500 K (4 feets long) , PF> 0.95, THD less 10%, with IP20 protection having open and short circuit protection, having input voltage range 90V to 300V connecting with three core flexible copper wire from connector to ceiling rose/angle holder as per existing site requirement as directed by Engr-in-charge. Make : Jaquar/Halonix/Philips .Note :- The rates are inclusive of cost of square box-02 nos including suitable size of clamps and screws etc. |
| 141 | Supply and fixing in repair LED Light fitting mirror type with high output diffuser 2 feet , 1 X 10 watt 220 V AC decorative type with driver holder and LED lamp, Alluminium housing, including connecting up with flexible copper conductor cable of suitable size complete all as specified and directed. |
| 142 | Supply and Fixing in repair wall mounted high quality indoor wall bracket light cylinderical/oval shape aesthetically designed fitting in wooden housing , glass and B22/E27 holder complete including inverter LED bulb B-22 cap with opal diffuser, IP-20 and inbuilt battery backup (LED INVERTER LIGHT 10W B22 CW IP) 10 watts including necessary eletric connection with PVC insulated multistranded copper cable of suitable size from ceiling rose to fitting terminal complete all as specified and directed. |
| 143 | Taking down unserviceable submain wiring and Material and Labour for submain wiring in PVC conduit with two runs of 6 sq mm and one runs of 6 sqmm for earth continuity 1100 v grade PVC insulated unsheathed FRLS grade copper conductor cable single core multistranded ISI marked (IS 694) drawn through and including 25 mm dia PVC rigid connduit heavy grade ISI marked (IS 9537 Part III) includung accessories such as bends, supports etc all as specified and directed. Note: Two runs of 6 sq mm and one runs of 6 sqmm cable along with conduit shall be measured as one length. |
| 144 | Supply and Fixing in repair MCB DB SPN 12 way of any size and capacity double door type horizontal with 200A busbar including disconnecting from mains and making good the disturbed surfaces complete all as specified and directed. |
| 145 | Supply and Fixing in repair MCB SP of capacity 5A - 32A 'B' curve complete all as specified and directed. |
| 146 | Supply and Fixing in repair MCB, SPN (Double Pole) 32 amps, 240 Volts, 10 KA ‘’C” curve complete all as specified and directed. |
| 147 | Material and Labour in repair for earthing with 600mmx600mmx6mm galvanised steel earth plate electrode buried vertically in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of the plate at a depth of not less than 1.5mtr below ground level, connected to and including G.I. wire of size 4 mm dia by means of bolts,nuts and check nuts and washers of galvanised steel, GI pipe 15 mm dia light grade pipe for protection of GI earth lead wire both to be provided to the extent of 7.5 metres as earthing lead and connecting to the eqpt/machinery etc. incl charcoal dust and common salt packed all around the earth plate in alternate layer in the earth pit all as per electrical plate No. 3 of SSR Part I-2009 including PCC chamber made up of PCC 1:3:6 type C1 20mm graded stone aggregates & RCC Chamer cover of size 540mmx540mmx100 mm made with 1:2:4 Type B1 20mm graded stone aggregates using 6 mm round MS bar & 8 mm MS bar for handle , 20 mm dia medium grade G.I. watering Pipe from top edge of the earth plate upto M.S. funnel with wire mesh provided inside the concrete earth pit for watering arrangement incl excavation and earth work in any type of soil and testing complete all as specified and directed. |
| 148 | Material and Labour for making suitable holes to the existing kitchen windows/walls and providing Exhaust fan steel body AC single phase , 230 volts of size 380 mm sweep with blades and frame and louvers complete all as specified and directed.Note : (i) The rates are inclusive of any civil work required to fix the exhaust fan. |
| 149 | Material and Labour for making suitable holes to the existing toilet windows/walls and Providing Exhaust fan steel body AC single phase , 230 volts of size 300 mm sweep with blades and frame and louvers complete all as specified.Note : (i) The rates are inclusive of any civil work required to fix the exhaust fan. |
| 150 | Taking down old unservicable ceiling fan and depositing it to MES store and Supply and fixing new ceiling fans complete with blades, down rods, electronic regulator/remote and connected accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC). complete all as specified and directed. |
| 151 | Supply and fix in repair single pole and neutral enclosure with a two pin and earth plug and socket complete with 20 Amp DP MCB complete all as specified and directed. |
| 152 | Taking down the existing serviceable kwh meter from site without any damage cleaning it properly and refixing the same in the new panel as directed by Engr-in-charge of the each block after completion of work complete all as specified and directed. |
| 153 | Supply, install testing and commissioning in repair manufactured by CPRI approved manufacturer indoor type LT panel board wall mounted, self supporting compartmentalised design of suitable size but not less then 1.2 Mtr X 1 Mtr X 0.3 Mtr, 440 V 3 phase 4 wire system powder coating provided with suitable to make it dust/vermin proof. The panel shall be made with 2 mm thick CRCA sheet for outer shell and inner shell made out of 1.6 mm thick CRCA sheet,double door with front openable with locking arrangement, provision of threaded earthing stud at bottom, inner shell be compartmentalized, front openable single door system lockable. Inner shell completely vermin proof and to accommodate incoming/outgoing MCCBs, MCBs and TPN aluminium bus and extension links. Aluminium bus bar of capacity 200 Amps- 4Nos, including neutral duly insulated with colour coded heat shrinkable sleeve and shall be mounted on suitable size/rating of epoxy resin insulator all housed in suitable bus bar chamber. All control wires shall be with 2.5 sqmm multi stranded copper conductors and shall be properly bunched,tied, ferrulled for proper indentification and crimped with adequate size of lugs and provision and fixing of Voltmeter,Ammeter with built in selector switch, CTs of suitable ratio, and pilot indication lamps complete along with provision of necessary cable entry/exit boxes for all incoming and out going cables with suitable size of cable glands etc. Computer cut shelf adhesive vinyl danger notice plate having conventional symbol of bone & skull be provided. The panel shall consists of following accessories:- Location :- (P-166 bldg) |
| 154 | i) Incomer a) MCCB four pole 16 KA rapturing capacity 63 Amps Ics= 100% of Icu thermal magnetic setting including connection with bus bar - 01 Nos (as incomer) |
| 155 | ii) Out going a) MCB SPN 40 Amp 10 KA 'B' curve -6 Nos (out going ) for each Qtrb) MCB SPN 10 Amp 10 KA 'B' curve -01 Nos (out going ) (for staire light and Bldg/S/Light) c) Voltmeter 0 to 500 volts of size (square dialed) 96 X 96 sq mm flush mounted, AC 50 Hz three phase energy accuracy class 1.0 including inbuild selector switch - 01 Nosd) Ammeter 0 to 100 amps of size 96 X 96 sq mm flush mounted, AC 50 Hz three phase energy accuracy class 1.0 including inbuild selector switch and suitable ratio of CT's complete - 01 Nos e) LED type RYB phase indicator lamp with back up HRC fuse - 01 Set f) Suitable space for fixing 7 No's single phase smart energy meter. Please Enable Macros to View BoQ information |
