|
| 1 | SITC of IR IP Based 5 MP Dome camera : 1/2.8\\" Progressive CMOS , ICR, IR 2560(H)X1920(V):25fps(P) , 2.8/3.6 mm lence (As per site requirement) H 264,H265/MJPEG, dual-stream, 120dB WDR or better , 3D DNR,BLC, IR: minimum 30 mtr, Provision for Support on-board storage up to 256 GB (SD card not included), intrution detection, line crossing detection Motion detection , Dynamic analysis, Alarm should br triggeron (Tampering alarm , Natwork disconnect, IP addess conflic , Storage exception ), security feature such as (password protection , privacy mask , watermark , IP address filtering, anonymouse access ), OPEN Standerd to support ONVIF (PROFILE S , PROFILE G ), Metal Housing, Vandal-proof housing IP 67, DC 12V & poE, complete with junction box for cable managment Oerating condition : 20°C -50°Cor better. Model should be : CE , BIS/UL,FCC,ROHS compliance. The CCTV OEM should have its office and survice/ support center in Rajasthan All as per pre approved by Engineer in chanrge. For additional technical parameter of products/work , refer Annexure \\"A\\" atteched with this BSR |
| 2 | Supply, Installation, Testing & Commissioning of 16 ch NVR Pre-licenced, NVR support up to 40 TB HDD Support, 16 ch IP inputs; ; Support NVR technology ; 320 mbps incoming bandwidth, support up to 12 MP full channel recording ; support H.265 compression ; 16 ch syncronised playback @1080p; support 3rd party cameras ONVIF type; 4K output : minimum 04 SATA HDD Slote ; each slot should support upto 10TB HDD ; Dual gigabite self adaptive Ethernet interface ; serial interfaece ; USB interface ;(all camera and storage - NVR Should be of same make for the smooth functioning of the system ) . complete with mounting accessories & junction box (to be provided by OEM ) for cable managment. Model should be ; certificates of compliance : UL CE/FCC, BIS. The CCTV OEM should have its office and service /support center in Rajasthan All as per pre approved by Engineer in chanrge. For additional technical parameter of products/work , refer Annexure \\"A\\" atteched with this BSR |
| 3 | Supply, Instalation, Testing & Communicationing of 3.5\\" 6 TB SATA , USB, 3.0 Surveillance Hard Disk All as per pre approved by Engineer in chanrge. For additional technical parameter of products/work , refer Annexure \\"A\\" atteched with this BSR |
| 4 | Supply, Instalation, Testing & Communicationing of BIS Compliance professional series Diagonal Screen size 43\\" LED with Resolutioin 3,840 x 2,160 (4K UHD) along with static (panel) Contrast Ratio (1300:1) or better with viewing angle of 178/178 degree with responce time of 8ms along with HDMI In 2.0-2 nos., USB 2.0-2 nos RS 232 -1 nos. With Built in Speaker (10 W + 10W ) , with high speed Processer and android or other reputated oprationg system along with 4 GB RAM along with all as per pre approved by engineer in charge. For additional technical parameter of products / work , refer Annexure \\"A\\" attached with this BSR |
| 5 | Supply, Instalation, Testing & Communicationing of 2 KVA 1 phase Input, With GBT Based Rectifier True Online Double Conversion Roubust desigh Widh input voltage range : 160~ 300 VAC @ 100% load (linearly derating to 50% load @ 100 VAC input ). generator Compatible with Wide Input volage window Double convertion Efficiency >91% & ECO mode efficiency up to 98% 100% load @ 0 ~ 40 C operating temp. Active input power Factor Correction 0.99 O/P power factor 0.9 inbuilt OVCD (Over Voltage Cut-Off Device) Fully Conform coated PCBA adaptable to harsh environment Digital Charge Technology Provide 02-10 A charging current Easy understanding LCD for convenient installatioin setup with Minimum 60 Minute Bettery back up (26 AH x 6 Nos of SMF batteries branded and recommended bby UPS OEM, battery stand and interlink FR PVC copper cable of appropriate size and lughs), with required cabling for incoming & outgoing connection. USP should be NABL certified with CE, ROHS & BIS compliance . All as per pre approved by Engineer in chanrge. For additional technical parameter of products/work , refer Annexure \\"A\\" atteched with this BSR |
| 6 | Supply & Installation of IP-20 & IK-08 , UL Listed Wall mounted Double Section Communication enclosure (Rack) made from powder coated (60 to 80 Micron) CRCA sheet, front sturdy sheet steel frame folded from one piece and welded with minimum 5mm toughened glass door,Vertical Mounting Rail 1.6 MM with 'U'Marking , with All round protective channel on the door aperture, lock integrated on front door, top and bottom cover with cable entry provision with gland plates, integrated side walls, 2 pair of 19\\" angles with wall mounting provision on wall. Accessories like: 1 No of 19\\" 1U Horizontal Cable manager, 1 No of 90 cfm 230V AC Fan with 1 mts long cable, mounting hardware , 1 No of 19\\" 1U, mountable socket strips with 5 nos of 5A universal sockets with 2 mts long power chord for supplying power to switches, fans etc along with earth continuity kit, indicator, moulded power supply cable. fixing on wall with Suitable Anchor fastner etc as required.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . 6 U Rack with Width 600 mm & Depth 400 mm + 100 mm |
| 7 | Supply , Installation, Testing and Comissioning of Unmanaged Switch Plug-and-play - easy setup with no configuration or no software needed, following Port fast ethernet - 8 port 10/100 MBPS auto-negotiation RJ45 ports, IEEE 802.3x flow control ,supports auto-MDI/MDIX, eliminating the need for crossover cables including making connection etc as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . 8 Port |
| 8 | Supply, Installation, & Testing of 19\\" 1U Rack Mounted/ surface mounted aluminum/ CRCA 1.2mm powder coated, Singlemode glass Fiber Optic Cable Patch panel/LIU loaded with flangless/screwable duplex adapters for ST/E-2000/SC/LC/MT-RJ/PC type, It should have easy removable Top plate with push buttons, there should be a splice tray installed in the Patch panel/LIU which can handle the fiber cores, splice tray should be PC+ABS material, it should include accessories like mounting hardware, gormetts, heat shrink tubes/sleevs, screws, nuts to install the panel for rack/wallmount applications as per requirment complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . 6 Ports |
| 9 | Supply, Drawing and Testing of 4 pair, 23 AWG Solid Bare Copper wire insulated with HDPE, U/UTP (Unscreened/Unshielded Twisted Pair), Category 6, Class E, 100 Ohm Impedance, Outdoor Cable as per latest ammendments of ANSI/TIA/EIA-568 C.2 & ISO/IEC 11801 2nd Ed, The copper conductors should be balanced twisted in pairs, seperated by a cross divider & protected by LSZH PVC outer jacket of UV resistant. Certified performance in a 4-connector configuration upto 100 Mtrs channel requirements & transmission frequencies up to 250 Mhz. Should meet IEEE 802.3af & IEEE 802.3at for POE applications. Cable Should support Ethernet 10GBASE-T according to the standards. in existing MS/PVC Conduits/casing capping including making connections to Information outlets and Patch Panels with jack & ferruling at both ends for identification with necessary tools for punching, stripping, crimping and testing etc as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . |
| 10 | Supply and erection of Galvanized Iron pole with galvanizing done in single dipping (Average coating thickness Minimum 65 Microns) continuously tapered poles having Octagonal / Circular cross-sections designed to withstand the maximum wind speed as per IS 875, The pole shaft shall be made from sheet steel (HT Steel Conforming to grade S355JO) and confirming to BSEN 10025 and shall be continuously tapered with single longitudinal welding. There shall not be any circumferential welding. The welding of pole shaft shall be done by Submerged Arc Welding (SAW) process. pole shafts shall be provided with the rigid flange plate of suitable thickness (Fe 410 conforming to IS 226 / IS 2062) with provision for fixing 4 no. foundation bolts, This base plate shall be fillet welded to the pole shaft at two locations i.e. from inside and outside.The octagonal Poles shall have lockable door of approximate 500 mm length at the elevation of 500 mm from the Base plate with bakelite sheet having 6A SP MCB and 16 sqmm stud type connector ( 4 nos) inside the pole at door opening for cable connection of following length and dimension as per table P-01 with base plate and foundation bolt on the Existing cement concrete foundation.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . Poles with Octagonal Cross Section 7 Mtr. |
| 11 | Plate Earthing as per IS:3043 with Hot dipped G.I. Earth plate of size 600mm x 600mm x 6.0mm by embodying 3 to 4 mtr. below the ground level with 20 mm dia. G.I. 'B' class watering Pipe ,including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, and Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height 250 to 300 mm. and embodying the pipe complete with alternate layers salt and coke/ charcoal, testing of earth resistance for value of 5 ohms or less as required & must record by engineer in charge during site visit and ensure to enter in measurment book.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . |
| 12 | Supply & Laying following size earth strip in horizontal or vertical run in surface by means of Earth strip DMC Insulator including riveting/ soldering/ welding, Jointing shall be done by overlapping and with 2 set of Brass (for Cu strip) / GI (for GI Strip) nut bolt & spring washer spaced at 50cm making connection etc. as required.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . 20mm x 3mm G.I. ( Hot Dipped ) Strip |
| 13 | vdq'ky Please Enable Macros to View BoQ information |
