|
| 1 | Construction of MINI M C F |
| 2 | 2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil |
| 3 | 4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III)derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 4 | 50.10.2:Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete |
| 5 | OD421737/2025-2026:Providing & fixing Chain link fabric fencing mesh of size 50x50 mm made of G.I. wire of dia 4 mm with M.S. Flat 15x3 mm and nuts & bolts complete. (Modified data of 10.29.1 with GI mesh 4mm dia) |
| 6 | OD421738/2025-2026:Providing and fixing Alu Zinc profile profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.40 mm (+0.05%) thickness. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. (Modified 12.50 of DAR) |
| 7 | OD421740/2025-2026:Providing and fixing Alu zinc roof sheet 0.40 mm (+ 0.05%) using self drilling/self tapping screws complete:Ridges plain (500-600 mm) (Modified data 12.51.1 DAR) |
| 8 | 13.62.1:Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture . |
| 9 | OD421739/2025-2026: Manufacturing, supplying and fixing signage boards made up of 2 mm thick aluminum sheet as approved by Engineer-in-Charge, letters, borders etc. including the cost of painting with two or more coats of epoxy paint in grey color on the back side of aluminum sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, fixing and erecting the same in position all complete as per drawings, specification and direction of the Engineer-in-Charges. (Rectangular area of the sheet only shall be measured for payment ).Modified 16.60.1 |
| 10 | 13.71:Lettering with black Japan pint of approved brand and manufacture |
| 11 | Bottle booth |
| 12 | 50.10.1:Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete |
| 13 | OD422963/2025-2026:Providing and fixing Alu-Zinc profile sheets (size, shape and pitch of corrugation as approvedby Engineer-in-charge) 0.40mm (+0.05%) thickness. Sheet should have protective guard film of25microns minimum to avoid scratches during transportation and should be supplied in singlelength up to 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using selfdrilling/self tapping screws of size(5.5x55mm)with EPDM seal, complete up to any pitch inhorizontal/vertical or curved surfaces, excluding the cost of purlins, rafter sand trusses andincluding cutting to size and shape wherever required. (MOD 12.50 of DSR ) (As per EECircular No. D3 dtd 02/07/21 |
| 14 | OD422964/2025-2026:Supplying and fixing :Welded steel wire fabric of required width having rectangular mesh painted with two or more coats of enamel paint of approved shade over a coat of primer(Priming and painting to be paid for seperately |
| 15 | 13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work |
| 16 | OD422965/2025-2026:Manufacturing, supplying and fixing signage boards made up of 2 mm thick aluminum sheet as approved by Engineer-in-Charge, letters, borders etc. including the cost of painting with two or more coats of epoxy paint in grey color on the back side of aluminum sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, fixing and erecting the same in position all complete as per drawings, specification and direction of theEngineer-in-Charges. (Rectangular area of the sheet only shall be measured for payment).Modified 16.60. |
| 17 | 13.71:Lettering with black Japan pint of approved brand and manufacture Please Enable Macros to View BoQ information |
