|
| 1 | Part A: BT Road work |
| 2 | Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking ofserviceable material up to a lead of 1000m including removal and disposal of top organic soil not exceeding in 150 mm thickness as per MoRTH specification clause 201 |
| 3 | By mechanical Means. |
| 4 | In areas of non-thorny jungle |
| 5 | Excavation for roadwork in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross-sections, and transporting to the embankment location with a lift upto 1.5 m and lead upto 1000 m as per MoRTH Specification Clause 301.3 |
| 6 | Construction of embankment with approved materials deposited at site obtained from roadway cutting and excavation from drain and foundation or other structures graded and compacted to meet requirement of Tables 300-1 and 300-2 as per MoRTH Specification Clause 305.3 |
| 7 | Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300-2 with lead upto 50m as per MoRTH Specification Clause 305.3 |
| 8 | Construction of Granular sub base by providing well graded material, spreading in uniform layers with Tractor Mount Grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per MORTH Specification Clause 401.For Grading III Material |
| 9 | Providing laying spreading and compacting specified graded sand, gravel (crushed stone) as per Table 400-1,400-2 or any other course material as per design mix, as per CBR in sub base course including premixing the material at OMC in wet mix plant, carriage of mixed material spreading in uniform layers with notor grader F.E loader on a prepared base and compacting with vibratory roller to achieve desired density (as per I.S. 2720) including all material, labor, machinery, lighting guarding, barricading and maintenance of diversion complete [MoRTH specification : Clause401]. By Mechanical means.For Grading II Material |
| 10 | Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400-12 & 400-13 and MoRTH Specification Clause 406.By Mechanical Means with all leads |
| 11 | Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base(WBM/WMM) including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per MoRTH Specification Clause 502 |
| 12 | Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surface treated with primer & cleaned with Hydraulic broom as per MoRTH Specification Clause 503. |
| 13 | Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.20 to 0.30 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per MoRTH Specification Clause 503. |
| 14 | Providing and laying Dense Bituminous Macadam on prepared surface with specified graded crushed aggregates as per table 500-8 & 500-10 and design mix for base/binder course including loading of material with Front end loader, heating of binder (including cost of anti-stripping compound wherever required) aggregate and filler as per table 500-9, in hot mix plant More than 60-90 TPH, transporting the mixed material by tippers and laying with sensor paver finisher as per clause 505.3.5 to the required level and grade rolling by self propelled power rollers and vibratory rollers or pneumatic tyred roller 150-250KN. TP=0.7MPa to achieve the desired density (approved by the department) but excluding cost of primer/tack coat. [MoRTH Specification : Clause 505 & 112] with all leads |
| 15 | Grading I (37.50 mm nominal size) - Bitumen @ minimum 4% of mix using VG 40 ( thickness 75 - 100 mm ) |
| 16 | Bituminous ConcreteProviding and laying bituminous concrete with 100-120 TPH batch type hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 to 5.6 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRT & H Specifications Clause 509 complete in all respects. |
| 17 | Grading I (19 mm nominal size) - Bitumen @ minimum 5.20% of mix & thickness 50 mm |
| 18 | VG-40 Grade |
| 19 | Part B: CC Road work |
| 20 | Dismantling of cement concrete pavements by mechanical means using pneumatic tools breaking to pieces not exceeding 0.02 cum in volume and stock piling at designated locations and disposal of dismantled materials upto a lead of 1000m, stacking serviceable and unserviceable materials separately |
| 21 | Providing laying spreading and compacting specified graded sand, gravel (crushed stone) as per Table 400-1,400-2 or any other course material as per design mix, as per CBR in sub base course including premixing the material at OMC in wet mix plant, carriage of mixed material spreading in uniform layers with notor grader F.E loader on a prepared base and compacting with vibratory roller to achieve desired density (as per I.S. 2720) including all material, labor, machinery, lighting guarding, barricading and maintenance of diversion complete [MoRTH specification : Clause401]. By Mechanical means.For Grading II Material |
| 22 | Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, coarse aggregate 26.5mm nominal size aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ cum, optimum moisturecontent to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonnes vibratory roller, finishing and curing. as per MoRTH Specification cl. 601. |
| 23 | Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with OPC 43 grade cement , coarse and fine aggregate (table 600-2 & 600-3) conforming to IS 383, maximum size of coarse aggregate 31.5mm nominal size mixed in a batching and mixing plant as per approved Mix design to achieve required design mix grade of controlled concrete, transported to site, laid with a fixed form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler bord , separation membrane, sealant primer, joint sealant (Table 600-4), debonding strip, dowel bar (IS : 432 Grade-I), tie rod(IS : 1786 Fe500 or IS : 432 Grade-I) , admixtures (IS : 9103 & IS : 6925) as approved, curing compound, finishing to lines and grades as per drawing including joimt cutting & texturing etc complete as per MoRTH Specification cl. 602 (with flexural strength minimum 4.5 MPa) |
| 24 | Providing & Laying of interlocking M-30 Grade Concrete Block pavements having thickness 100 mm as per drawings and as per IS 15658:2006 and all materials shall confirm to MoRTH Specification Clause 602 with M-30 grade 0.30 mtr x 0.30 mtr x 0.15 mtr. edge blocks |
| 25 | Category 'B': Dentated only two sides like I,Z,T shape as per IRC:SP:63-2004 |
| 26 | Part C: Divider Construction |
| 27 | Providing and laying Reinforced cement concrete M20 mix with stone aggregate 20mm nominal size mechanically mixed and vibrated for bed plates excluding steel reinforcement but including centering and shuttering, laid in position .[MoRTH Specification : Clause 1000/700] |
| 28 | Providing and fabricating steel reinforcement for R.C.C works including cutting, bending, placing in position and binding complete including cost of binding wire .[MoRTH Specification : Clause 1000/1600] |
| 29 | HYSD/TMT bars |
| 30 | Part D: Road Furniture work |
| 31 | Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and MoRTH Specification Clause 801 |
| 32 | 5th Kilometre Stone (precast) |
| 33 | Ordinary Kilometer Stone (Precast) |
| 34 | 200 m stone (precast) |
| 35 | Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 801.3.1 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and MoRTH Specification Clause 801,900 mm equilateral triangle |
| 36 | Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 801.3.1 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and MoRTH Specification Clause 801,800 mm x 600 mm rectangular |
| 37 | Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 801.3.1 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and MoRTH Specification Clause 801,600 mm circular |
| 38 | Marking Centre Line and stop lines etc. on road as IRC pattern with thermoplastic paint of approved quality and make with 8% glass beads laid on the road surface at temperature 160C with a special applicator machine complete with a special applicator with labour, material and traffic diversion arrangements. |
| 39 | Supplying of Cat's Eye made of aluminium alloy size 75x100x22 mm haing 21 biconvex lenses embedded in circular disk of ABS plastic on each side. Please Enable Macros to View BoQ information |
