|
| 1 | Civil Work : Surface dressing of the ground including removing vegetation and inequalities not exceeding 15cm deep and disposal of rubbish lead up to 50 Mtr. and lift up to 1.5 Mtr.: All kinds of soil |
| 2 | Earth work in excavation in foundation trenches or drains including dressing of sides and ramming of bottoms, lift up to 1.5 Mtr. including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. All kinds of soil |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead up to 50 meter and with all lift. |
| 4 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size). |
| 5 | Centering & Shuttering with plywood or steel sheets including strutting, propping, bracing bothways and removal of formwork for foundations in basements rafts, footings, strap beams bases of columns, etc. upto plinth level. |
| 6 | Providing and laying in position specified grade of cement concrete for all RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints excluding the cost of centering, shuttering and reinforcement. M20 grade Design Mix |
| 7 | Providing and laying in position specified grade of cement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcement for Walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc.M20 grade Nominal Mix |
| 8 | Providing and laying in position specified grade of cement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement for Beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.M20 grade Nominal Mix / Design Mix |
| 9 | Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for : Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates, anchor blocks, sills, chhajjas, lintel, beam, plinth beam etc. |
| 10 | Columns, pillars, posts and struts etc. |
| 11 | Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor three level. Thermo-mechanically Treated bars (Tata, SAIL) |
| 12 | Random Rubble stone masonry with hard stone in foundation above plinth level and upto five level above 30cm. thick walls in : Cement Mortar 1:6 ( 1-Cement : 6-Sand). |
| 13 | Brick work in super structure upto third storey. with Flyash Flyash Bricks of class designation 75 in : Cement mortar 1 : 6 (1 cement : 6 coarse sand). |
| 14 | Extra over item No. 5.1 for brick work in : - Square or Rectangular Pillars. |
| 15 | Half brick masonry in super structure upto third storey. using bricks of designation 75 in : Cement mortar 1 : 4 (1 cement : 4 coarse sand). |
| 16 | Providing & fixing precast cement concrete coping 1 : 2 : 4 mix 50mm thick complete as per specification : |
| 17 | Making khurras 450 x 450mm with average minimum thickness 50mm cement concrete 1 : 2:4 over P.V.C. Sheet 1 Mtr. x 1 Mtr. x 40micron finished with 12mm cement plaster 1 : 3 and one coat of neat cement, rounding edges and making and finishing the out let complete. |
| 18 | Carriage of Earth, Sand, Lime, Morrum, manure or sludge including loading, unloading with Avg. lead of 10 kms. |
| 19 | Grading roof for water proofing treatment with water proffing compound Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 20 | Providing batta (gola) 75 mm x 75 mm in cement concrete (1 : 2 : 4) including finishing with cement mortar 1 : 3 as per standard design. |
| 21 | Supplying and providing of two components poly sulphide sealant containing solid contents, confirming to standard specification and approved compatible primer, for priming vertical faces prior to application of poly sulphide sealant including all labour charges for sealing of expansion joints after drill mixing of two components sealing compound. Cleaning and preparation of expansion joint using wire bush sand papering with emery paper and filling with suitable mechanical means. The work includes racking and cleaning of joints, applying primer on edges, using masking tape on edges, providing of sealant and removal of masking tape immediately after providing sealant in joint. To vertical joint between R.C.C. columns, bricks & stone masonry in size 40 mm width and 12 mm depth, including providing back up material (Thermocoal foam) if required. |
| 22 | To joints in flooring, as per drawing with first layer of poly sulphide sealant in size 20 mm width and 10 mm depth and then providing polyethylene foam back up rod 25 mm dia size and finally providing another layer of poly sulphide sealant in size 20 mm width and 10 mm depth over P.E. back up rod as per application procedure and direction of Engineer-in-charge. |
| 23 | Polished Blue Kota stone flooring skirting, laid over 20 mm thick base of C.M. 1 : 4 and jointed with grey cement slurry to match the shade of the slab including rubbing and polishing complete : For area of each slab from 2001 to 5000 Sq.Cm : 25 mm thick slab. |
| 24 | Polished Blue Kota Stone slab in steps, walls, pillars having fine machine cut edges laid on 12 mm (Av.) thick cement mortar 1 : 3 and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete : 30 mm thick slab area 2001 to 5000 Sq.Cm. |
| 25 | Providing and fixing Marble stone flooring table rubbed, 15-18 mm thick over 20mm (Av.) thick base of CM 1:4 (1 cement : 4 coarse sand) jointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. |
| 26 | Rajnagar 1st quality/Ageria with light spots. Above 3601 Cm2 Slabs |
| 27 | Abu (Green Marble) Above 3601 Cm2 Slabs |
| 28 | Cement concrete flooring grade 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate) rounding off edges etc. but excluding the cost of nosing of steps etc. complete : 75 mm thick with 20 mm thick nominal size aggregate. |
| 29 | Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of : i) Ist course of applying cement slurry @ 4.4 Kg/sum mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.ii) IInd course of 20mm cement plaster 1:3 (1 cement: 3 coarse sand) mixed with water. proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface..iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 Kg per sqm. of area.iv) IVth course of 400 micron thick PVC sheet .(Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 Kg/sqm.) |
| 30 | Filling of sunk portion of roof with earthen pots of required height including filling voids with 1 : 2 : 4 light concrete, using brick bats complete leveling and dressing the surface by 50 mm thick cement concrete 1 : 2 : 4 as per specification. |
| 31 | Supplying and fixing in walls machine cut and polished stone shelves, tands and in CM 1:3 with machine cut edges : Kota stone 25 to 30mm thick. |
| 32 | Sand or other approved stone 25mm thick. |
| 33 | Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. 15-18 mm thick laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. Green / Black Above 1501 Cm2 to 3600 Cm2 Tiles |
| 34 | Extra for providing edge moulding to 18 mm thick marble stone counters, vantities etc. over item No. 7.1 & 7.2 including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite Work |
| 35 | Marble Work |
| 36 | Providing and fixing 1st quality standard White / Ivory Glazed Tiles ISI marked [IS : 13753] of size 300 mm x 200 mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in white cement mixed with pigment to match the shade of tile complete (excluding the cost of cement plaster on walls and pillar). Catgory-A : Kajaria, Johnson, , Somani make etc. |
| 37 | Providing and fixing 1st quality MAT finished ceremic tile size 300 x 300 mm confirming to IS : 13753 colour such as white, grey, ivory, fume red brown in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry including nicely finished joints using water proof joint filler powder (Untile of Roffe make) and finishing with flush pointing in white cement mixed with pigment to match the shade of the complete (including the cost of cement mortor bed 1:4). Category -A : Kajaria, Jhonson, Somani make |
| 38 | P & F Vitrified Porcelain Polished tiles ( Naveen/ Euro make , size 600 mm x 600 mm and thickness 10mm) on floor, skirting and steps etc. laid with tile admixture (Roff Pidilite or equivalent) including filling of joints by water proofing tile grout (Fevimate, Roofie, Untile or equivalent) specially for adhesive with graded granuals, polymer and stable pigment fine finished including cleaning of joints etc. complete as per direction of Engineer Incharge. Conforming to IS 15622 of approved make in all colour and shade, |
| 39 | Providing and fixing factory made P.V.C. door frame manufactured by M/s Rajshri of the size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm PVC foam sheet mitred at two corners and jointed with 2 Nos. of 150mm long brackets of 15x15mm M.S. square tube. The two vertical door profiles are to be reinforced with 19x19mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame shall be fixed to the wall using 65/100 mm long M.S. Screws through the frame by using PVC fasteners. A minimum of 4 nos of screw to be provided for each vertical member and minimum 2 nos for horizontal member etc. complete as per manufactures specification and direction of Engineer in Charge. |
| 40 | Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formal dehyderesin in glue both sides with approved steel fittings complete as per annexure 'A' : 35 mm thick . Commercial Veneer both side |
| 41 | Providing and fixing to existing door frame 30 mm thick factory made Polyvinl Choloride (PVC) door shutter made of styles and rails of a UPVC hollow section of size 60 x 30 mm and wall thickness 2 mm + 0.2 mm with inbuilt decorative moulding edging on one sides. The styles and rails mitred and jointed at the corners by means of M.S. galvanised / plastic brackets of size 75 x 220 mm having wall thickness 1.0 mm and stainless of size screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25 x 20 mm and 1 mm + 0.1 mm wall thickness. The lock rail made up of 'H' section, a UPVC hollow section of size 100 x 30 mm and 2 mm + 0.2 mm wall thickness fixed to the shutter style by means of plastic / galvanised M.S. 'U' cloats. The shutter frame filled with a UPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm + 0.1 mm wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufactur's specification and direction of Engineer-in-charge including all door, fittings such as Hinges, L-drop, Handles, Locking bolts etc. as per approved of Engineer-in-charge. |
| 42 | Add extra in Flush doors : For External teak wood lipping on flush door 35mmx6mm |
| 43 | Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured). |
| 44 | Providing and fixing in position collapsible steel shutters with vertical MS Channels 20 x 10 x 2 mm and bracket with flat iron diagonals 20 x 5 mm size with top and bottom rail of T-iron 40 x 40 x 6 mm with 40 mm dia steel pulleys / ball bearing complete with bolts, nuts locking arrangements inside and outside stoppers, handles etc. as per specification including applying a priming coat of approved steel primer. (To be measured and paid as per outer dimension). With 75 mm opening when closed. |
| 45 | Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide Add extra if square,rectangular hollow tubelar sections are used |
| 46 | Providing and fixing welded mesh / expanded metal mesh in frame work, flat iron beading 20 x 3 mm including top cross laps inside and out sides welding, iron bolts, screws, clips etc. complete (excluding frame work) of size. Welded mesh 25 x 25 mm x 16 gauge. |
| 47 | Supplying and fixing of Steel windows made out (65 x 40 mm) hollow metal pressed section of 1.25 mm thick sheet F4 & F7 standard rolled section conforming to IS 1038 with wholly openable shutter of 0.80 mm thick (out side & inside) opening C.R. sheet embossed panels, joints matted and flush welded with suitable hinges, steel lugs & screws with approved oxidised steel handles, fittings, peg stays (casement stays) etc. complete in all respect including providing 10 mm square M.S. bars 10 cm. C/C and applying priming coat of red oxide paint. |
| 48 | Supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20 x 3 mm with suitable screw at not exceeding 150 mm distance. |
| 49 | Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish : 25 mm thick |
| 50 | Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish : 20mm thick. |
| 51 | Applying Birla / JK white cement based putty over cement plaster surface for making even surface. |
| 52 | Applying plaster of Paris over cement plaster surface for making even surface. |
| 53 | Painting with enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work. |
| 54 | Applying priming coat : With ready mix pink or gray primer of approved brand and manufacture on wood work hard and soft wood. |
| 55 | Making grooves as per design in plaster 10mm to 20mm wide.Making of drip course (Tapka) in cement sand mortar 1:6 width upto 40 mm and 10 mm thick as per approved design |
| 56 | Providing and fixing anodized aluminium work (Anodizing to be got done from approved Anodizer) for doors, windows, ventilators and partition with extruded built up standard tubular and other sections of approved make confirming to IS : 733 and IS : 1285 anodised transparent 81 dyed to required shade according to IS : 1868. (Minimum anodic coating of grade AC 15), fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasterners including necessary filling up of gas at junctions, at top, bottom and sides with required PVC / neoprene felt etc.; Aluminium section shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, Al. Tower bolt & Al. handle & Al. Aldrop etc. all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and paneling to be paid for separately). For fixed portion |
| 57 | For shutters of doors, windows & ventilators including providing and fixing hinges / rollers etc. and making provision for fixing of fittings wherever required (lockes shall be paid for separately). |
| 58 | Providing and fixing glazing in aluminium door, window ,ventilator shutters and partitions etc. with PVS / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge.(Cost of aluminium snap beading shall be paid in basic item.) With float glass panes of With glass panes of 4.0 mm thickness (weight not less than 10.0 kg./sqm) as per IS : 2835. |
| 59 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture to aluminium door shutter confirming to IS : 6315 including cost of cutting floors as required, embedding in floors and cover plate etc. complete as per direction of Engineer-in-charge. |
| 60 | Providing and fixing brass lock without handle for Aluminium door, of approved quality, make & design as directed by Engineer-in-charge. |
| 61 | Providing and fixing expanded grill made of anodised aluminium as per design and drawing having members section of size 7.5 mm x 6.0 mm and opening of size 102 mm x 99 mm to aluminium window / vent with required screws, Y and H aluminium sec (as per drawing) at the ends and middle joints respectively complete in all respect as per direction of engineer in charge. |
| 62 | Providing & laying Chequerred plain cement concrete embossed to specially manufactured non-slipping tiles of approved make 20 mm thick laid on 20 mm thick bed of cement mortar 1 : 6 jointed with neat cement slurry complete. |
| 63 | Add extra for chequerred coloured plain cement concrete or specially manufactured non-slipping tiles of approved make 20 mm thick. |
| 64 | Random rubble dry stone Kharanja under floor. |
| 65 | Providing and fixing 12 mm thick pre laminated three layer medium density (exterior grade) particle board Grade I, Type-II confirming to IS : 12823 bonded formaldehyde synthetic resin, of approved brand and manufacture in paneling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and direction of engineer-in-charge. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side. |
| 66 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M15 grade Nominal Mix (with graded stone aggregate 20mm nominal size). |
| 67 | S&f fixed wire gauge of stainless steel of 14 mesh x 24 gauge to the aluminium window by Aluminium beading 20x3mm with suitable screws at not exceeding 150mm distance at all heights with all lead and lift with scafolding. |
| 68 | Cement concrete jali reinforced with 1.6 mm dia Mild steel wire complete as per approved design excluding plastering of jambs, sills and soffits: 75mm thick |
| 69 | Supply and fixing in cement mortar welded hand railing made out of MS round or square bars, flats etc. for staircase or verandah as per design complete in all respect (wooden or PVC hand railing to be paid extra) with priming coat of red oxide. |
| 70 | Providing and fixing fully panelled doble leaf shutter for doors as per approved design and drawings with approved ordinary C.P. / oxidised steel fittings as per Annexure-'A\\" and width of styles & top rails of 100 mm and lock rails width of 150 mm and bottom rails of 200 mm width including teak wood beading of size 19 mm x 12 mm on both faces complete : 30 mm thick Ghana teak wood grade-I Wire gauge 24 gauge 14 mesh of IS designation 85 gauge wires of dia 0.56 mm panels |
| 71 | Providing and fixing M.S. sheet single leaf door shutter in angle iron frame 35 x 35 x 5 mm suitabilly diagonally braced with 25 x 3 mm flat iron above and below lock rail of size 50 x 5 mm beading extra including all fittings, as per direction of Engg. incharge but excluding cost of chowkhats : including two coats of anit-corrasite red oxide primer paint. M.S. Sheet 22 S.W.G. |
| 72 | Supplying and fixing rolling shutters of approved make, made of 80 x 1.25 mm M.S. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangement for inside and outside locking with push and pull operation complete including cost of spring hooks, providing and fixing necessary 25.3 cm. long wire springs grade No. 2 and M.S. top cover 1.25 mm thick or rolling shutters as per design. (Clear openable area to be measured for payament). |
| 73 | Providing and fixing ball bearing for rolling shutters. |
| 74 | Earth work in excavation over areas (exceeding 30cm in depth, 1.5 Mtr. in width as well as 10 Sqm on plan) including disposal of excavated earth lead up to 50m and with all lift disposed earth to be levelled and neatly dressed: All kinds of soil |
| 75 | Random Rubble stone masonry with hard stone in superstructure above plinth level and upto five level above 30cm. thick walls in : Cement Mortar 1:6 ( 1-Cement : 6-Sand). |
| 76 | Pointing on stone masonry in cement sand mortar 1:3 (1 cement : 3 sand) : Raised and cut pointing. |
| 77 | Providing and fixing of precast concrete interlocking blocks of 80mm thick (M-30 Grade) manufactured from fully computerized automatic stationery hydraulic vibto perssed machine & full computerized automatic batching plant of class A-I as per BS: 6717-2001. The CC interlocking paving blocks be laid on average 50mm thick bed of coarse sand and the joint is to be filled with fine sand. Laying procedure on compected sub base as defined. The work includes earth work in cutting of B/T road, cutting of WBM road and disposal of unserviceable Material with all leads & lifts and stacking of serviceable Material complete job is to be executed as per the instructions of Engineer-in- charge. The rates to be inclusive of all lead, lifts & taxes General specification of Blocks:1. Shape : As specified by Engineer-in-charge.2. Tensile splitting strength and breaking load as per BS : 6717-2001.3. Colour : Grey cement natural colour4. Variation in Dimension : Less than 1.6mm5. Variation in thickness : Less than 3.2mm |
| 78 | Providing and laying in position specified grade of cement concrete for all RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints excluding the cost of centering, shuttering and reinforcement.M20 grade Design Mix |
| 79 | Construction of tube-well from ground level and upto 100 Meter depth and above sizes in all types of soils in alluvium strata by “bailing” method and without gravel packing as per IS: 2800 (Part - I& II) 1979 specifications (The work includes formation of cavity well at bottom by development with appropriate air compressor or bailer pumping and also lowering of casing pipe but excluding cost of the casing pipe. The tube-well should have a throughout bore as per nominal bore of casing pipe. The work would be completed after obtaining sand free water.)150mm-do- |
| 80 | Supply of ERW M.S. black casing pipe ISI marked (IS:4270/1992) of grade Fe410 of following sizes at site of work.150 |
| 81 | S & F tube well cover of M.S.sheet (6mm thick) with nuts and bolts complete for casing size:150mm dia |
| 82 | Supply & fixing M.S. clamp, set of 50 x 6 mm flat from iron with nuts and bolts etc. for holding the riser pipe assembly of submersible pump set. |
| 83 | Supplying and installation of 32 mm dia G.I. pipe medium class ISI marked in 3m length including all accessories and fittings required for installation of hand pump. |
| 84 | SITC of radial / mixed flow submersible motor pump sets ISI marked (IS:8034-1989) of approved make with required accessories including making connection suitable for T.W./ D.C.B./ Open well. The job includes lowering of riser pipe, G.I./ H.D.P.E. pipe with rope, cables, installation of complete fitting and accessories, jointing of electrical cables up to switch board. All labour for testing of submersible pumps set and supply of water to water mains, complete in all respect.150 mm diameter Submersible pump shall have following HP Rating, phase, Head, minimum Discharge respectively.5.0 HP, 3-Ø, (33-99)Mtr, (234-84)LPM |
| 85 | P/Laying ISI marked P.V.C. insulated submersible cable confirming to IS:694 with flexible copper conductor including making connection etc. as required.4.0 Sq.mm 3 core flat / Round |
| 86 | Providing & Fixing of HDPE pipe ISI mark (IS:4984/95) for water supply (suitable for submersible & jet pump) with required fittings for vertical installation, 40 mm OD 6 kg / cm2, 40 mm OD 6 kg / cm2 |
| 87 | Supply and fixing of Oil / Air break Starter panel made out of sheet steel powder coated enclosure comprising of over load protection relay, short circuit & single phasing protection, ON / OFF push buttons, ammeter, voltmeter, indicating lamps etc. complete in all respect suitable for following rating motors.3.0 HP to 10.0 HP ( Star / Delta ) |
| 88 | Maintenance free Gel Earthing with Pipe in pipe / Pipe in strip technology filled with anti corrosive conductive compound ( CPRI Tested ) below the ground in 150 - 200 mm dia. earth pit & surrounding filled with required mineral filling compound ( MFC should have hygroscopic property to retain the moisture for long time to create low resistance zone ) and C.C. finished chamber covered with hinged type with locking arrangement C.I. Cover, C.I. Frame of size 300mm x 300mm complete testing of earth resistance as required. of following sizes.GI pipe 2000 mm long, 50 / 25mm, Terminal 12 mm GI Strip |
| 89 | P & F G.I. Pipes (External Work) with G.I. fittings excluding union (IS : 1239 Mark) including trenching & refilling earth etc.25mm dia nominal bore 'B' Class |
| 90 | Supplying and Filling in plinth with river sand under floors including watering ramming consolidating and dressing complete including cost of sand |
| 91 | Providing and fixing expansion joint board for building R.C.C. column beams, walls, slab of Polyethylene foam of density 30 to 35 Kg./m3 of Armour Board. 40 mm thick. |
| 92 | Providing and Fixing superior quality like Hardvyn or equivalent hydraulic door closure. |
| 93 | Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete : 20 mm |
| 94 | Providing and fixing cow catcher made of R.S. joist angles channels MS rounds including cutting welding and fabrication with priming coat of red oxide (as per design). |
| 95 | Providing and fixing T iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded with 15 x 3 mm lugs, 10cm long embedded in cement concrete blocks 15 x 10 x 10 cm of 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as require including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. |
| 96 | Providing corrugated G.I. Sheet roofing fixed with G.I.J. or L hooks bolts and nuts 8 mm diameter with bitumen and G.I. Limpet washers or with G.I. Limpet washers filled with white lead and including a coat of approved steel primer and two coat of approved paint on over lapping of sheet complete (upto a pitch of 60°) & excluding the cost of purlins rafters and truses, for class of sheets : 0.63 mm thick |
| 97 | P & F Plain Fiber glass sheet (FRP sheet fibre Reinforcement product sheet confirming to IS : 12866-1989 having alumnium thickness as below including fixing with nuts, bolts hooks and bitumen washer etc. complete. 1.5 mm thick (Wt. 2.5 Kg./Mtr. Sq.) |
| 98 | Providing and laying in position specified grade of cement concrete for RCC structural elements upto floor three level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints excluding the cost of centering, shuttering and reinforcement for :-Beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases.M20 grade Nominal Mix |
| 99 | Add extra over item no. 4.1.2 , 4.2.1.2 , 4.2.2.2 and 4.2.3.2, Providing M-25 grade R.C.C. instead of M-20 grade R.C.C. |
| 100 | Sanitary Work : P & F Indian type white glazed vitreous china 1st quality W.C. orissa pan (IS :2556 Mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor: Size 580x440mm. |
| 101 | P & F European type white glazed vitreous china 1st quality W.C pan (IS : 2556 Mark) with P or S trap including cutting and making good the wall and floor |
| 102 | P & F water closet Seat Covers with brass hinges complete :Solid PVC (ISI marked) grade-I White for EWC. |
| 103 | P & F lst quality WVC Urinal (IS:2556 mark) with 25mm dia G.I. waste pipe, dome waste couplings, concealed iron brackets or screws etc complete. Mini stall size 455x385x350mm. |
| 104 | P&F Marble Urinal Partition slab both sides polished of approved design cut from marble size 900x600mm. Makrana II quality marble having light spots |
| 105 | P & F W.V.C. Half-Round Channel of approved make in C.M. 1:3, joints finished in white cement of:Size 150mm dia. |
| 106 | P & F Low level Flushing Cistern of 10 litres capacity (IS : 2556mark). Of approved make with complete fittings C.I. brackets duly painted, brass ball cock with ball, (IS: 1703 mark) complete including cutting and making good the wall:PVC with PVC bend as per IS : 7231 . |
| 107 | P & F C.P. brass Urinal Spreader for stall urinal of approved make. |
| 108 | P & F WVC Wash Basin (1st quality IS : 2556 mark) of approved make with C.I. brackets duly painted, 1 No. 15 mm C.P.Pillar cock (IS : 8934 mark) & 32 mm C.P. brass waste coupling of approved make, 25 mm G.I. waste pipe complete including cutting & making good the wall Size 580 mm x 450 mm. |
| 109 | P & F Kitchen & Lab. Sink of approved make with C.I. brackets duly painted, 40 mm C.P. waste coupling, C.P. Brass chain with rubber plug, 40 mm G.I. waste pipe up-to floor level complete including cutting and making good the wall & floor :Fire clay glazed kitchen sink (I.S. Marked) size 600 x 450 x 200 mm. |
| 110 | P & F Kitchen & Lab. Sink of approved make with C.I. brackets duly painted, 40 mm C.P. waste coupling, C.P. Brass chain with rubber plug, 40 mm G.I. waste pipe up-to floor level complete including cutting and making good the wall & floor : 1.0 mm thick Salem stainless steel AISI -304 kitchen sink of approved make (Nirali, Neel – kanth, Jaina, Faber-Castell ) with large waste coupling. Overall size Bowl size (inches) (inches) 18 x 16 x 6 16x14x6 |
| 111 | P & F Looking Mirrors with P.V.C. frame of approved (Atul, Modi Guard , Saint Gobin or equivalent)Size 500x400mm |
| 112 | P & F Towel Rail or Ring of approved quality/make: |
| 113 | C.P. brass Towel Rail elbow type with concealed screws size 450mm (Heavy duty). |
| 114 | CP Brass towel ring revolving type |
| 115 | P & F Grating of approved quality/make:Stainless Steel Sheet size 125mm dia. Heavy Quality of approved make |
| 116 | P & F Extension Pipe for bib cocks of approved quality/make.C.P. brass of Heavy & Superior quality 50x15mm |
| 117 | P & F G.I. pipes (Internal Work) with G.I. Fittings excluding union (IS:1239 Mark) & MS clamps including cutting and making good the walls and floors: |
| 118 | Exposed on wall 15 mm dia nominal bore 'B' Class |
| 119 | Exposed on wall 25mm dia nominal bore 'B' Class |
| 120 | P & F G.I. Pipes (External Work) with G.I. fittings excluding union (IS : 1239 Mark) including trenching & refilling earth etc. |
| 121 | 15mm dia nominal bore 'B' Class |
| 122 | 25mm dia nominal bore 'B' Class |
| 123 | P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make: |
| 124 | C.P. Brass bib cock,15mm nominal bore. |
| 125 | (-do-) Elbow-action, 15mm nominal bore. |
| 126 | (-do-) Long body, 15mm nominal bore weight not less than 690 gm |
| 127 | P & F Stop Cock (IS :8931 Mark), superior quality & of approved make:C.P. Brass 15mm nominal bore. |
| 128 | P & F Inlet Connection (Angle Valves) Superior quality, of approved make, for Wash basin, Gyser etc. C.P. Inlet connection 15mm.Brass (IS : 8931 marked)with 37 cm long pipe and nut. |
| 129 | P & F Flush Cock / Flush Valve (IS : 9758 Mark) for WC of approved quality make :CP brass push type 15mm nominal bore.) concealed 25mm nominal bore. |
| 130 | P & F Full-way Valve (IS:778 Mark) or wheel valve of approved make : |
| 131 | Gun-metal 15mm nominal bore. |
| 132 | Gun-metal 25mm nominal bore. |
| 133 | P & F PVC Storage Tank ISI Marked (IS : 12701) indicating the BIS license No), of approved make with cover, 25mm dia 1M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design: |
| 134 | 500 litres capacity. |
| 135 | 1000 litres capacity. |
| 136 | Providing Laying & jointing glazed S.W. pipes grade `A` (IS;651 marked) of approved make with spun yarn & stiff mixture of cement mortar 1:1, excavation & refilling of earth in all types of soil upto 1.2m depth, S.W. fittings, including testing of joints etc, complete :150 mm Dia |
| 137 | Providing & Laying C.C. 1:5:10 (Stone aggregate 40mm nominal size) all around S.W. pipe including 15 Cm. thick bed concrete (Width W= Diameter of pipe in Cm+30 Cm.)( Excluding cost of pipe)150mm dia S.W. pipe |
| 138 | P & F Square-mouth gully trap `A` grade (IS :marked) of approved make complete with C.I. grating, frame & Cover masonary chamber in C.M. 1:6, 100mm thick C.C. 1:5:10 base concrete, 40mm thick C.C.M-15 grade coping, 12mm thick cement plaster in CM 1:3 complete as per approved design & type. |
| 139 | Trap size 150 X 100mm, 7.2 Kg CI cover with frame, Internal Chamber size 300 X 300mm. |
| 140 | Trap size 225 X 150 mm, 15 Kg CI cover with frame Internal Chamber size 450 X 450mm. |
| 141 | Construction of manhole in all type of soil inner size 90 X 60 Cm. 300 mm thick masonry in CM 1:6, 10 Cm. thick cement concrete 1:5 10 in foundation, 20 mm thick inside plaster in CM 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring, making channels, 80mm thick stone slab covering with 40mm thick M-15 grade C.C. flooring, Cement cover with frame of 450mm dia, earthwork etc. complete as per design including disposal of surplus earth within 50 mtr. lead.Depth up to 0.5 M |
| 142 | Construction of chamber in all type of soil with 300 mm thick masonry in CM 1:6 m 10 cm thick C.C. 1:5:10 in foundation, 20mm thick insider plaster in Cm 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring , earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr.Inside size 300 X 300 mm depth upto 0.5 M Cement cover with frame. |
| 143 | Construction of soakage well in all type of soil with 300 mm thick dry masonry, top and bottom 300 mm course in CM 1:6, 80mm thick stone slab, jointing of slab in CM 1 : 3, Ralthal, Kharanja, 40 mm thick M-15 grade C.C flooring , earthwork complete as per approved drawing including disposal of earth within a lead of 50 mtr.:Size 300Cm. dia outside & 300 Cm. depth. |
| 144 | Add extra if Soakage Well is filled with dry stones. |
| 145 | Construction of septic Tank in all types of soil with 40 Cm .thick masonry in CM 1:6, 15 Cm thick C.C bed of 1:5:10, M-15 grade C.C flooring & over stone slab covering ,80 mm thick slab ,jointing of slab in CM 1:3. Ralthal, Kharanja, 50 mm thick stone partition walls, 20 mm thick plaster in CM 1:6 finished with neat floating cement, 4 Nos C.I foot rests of approved design ,two No. 450 mm dia each Ferro cement cover with frame, earth work etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 mtr:- |
| 146 | Size 230 x110 x150 cm.(for 20 users) |
| 147 | Size 400 x140x150 cm.(for 50 users) |
| 148 | Construction of Open Surface Drain with 112mm thick brick masonry in CM 1:4,110mm thick base concrete 1:5:10, 37mm thick M-15 grade C.C. flooring ,12mm 1:4 cement plaster on all exposed faces of walls including top surface excavation & disposal of earth complete as per approved design/drawing:150mm drain,225mm Av. depth |
| 149 | Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes Type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make110 mm dia |
| 150 | Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes fittings type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make |
| 151 | Bend 87.5 Dg. 110mm dia |
| 152 | Door bend 87.5 Dg 110 mm Dia |
| 153 | Single Tee with Door 110 mmdia |
| 154 | Vent cowel 110 mm dia |
| 155 | Offset |
| 156 | Coupler 110 mmdia |
| 157 | Pipe clip 110mm dia |
| 158 | Nahni Trap without Jali 4” 110mm dia |
| 159 | P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.) approved quality /make including joining the pipe with solvent cement rubber ring and lubricant. |
| 160 | 75 mm dia |
| 161 | 110 mm dia |
| 162 | P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: |
| 163 | Coupler (socket) 110mm dia |
| 164 | Bend 87 .5 75mm dia |
| 165 | Bend 87 .5 110mm dia |
| 166 | P & F Bath Shower of approved quality/make.C.P. brass of Heavy & superior quality 150mm. |
| 167 | P & F Shower arm 15mm dia of approved uality/make.C.P.brass heavy & superior quality 220mm Projection. |
| 168 | P & F Jet spray for water closet with C.P. Copper Tube flange of approved make. |
| 169 | P & F Soap Dish or Tray of approved quality/make,C.P. brass heavy and superior quality. |
| 170 | Hoisting Charges for each floor : |
| 171 | For 500 liter Tank |
| 172 | For 1000 liter Tank |
| 173 | P & F Ball Cock (IS:1703 Mark) with Rod & P.V.C. Ball complete : Brass wt. 400 gm, 15 mm. |
| 174 | P & F 15 mm. Dia Connection Pipe of approved quality/make :(-do-) 600mm. Please Enable Macros to View BoQ information |
