|
| 1 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer-in-charge 1: 3: 6 or richer mix. |
| 2 | Earth work in rough excavation, banking excavated earth inlayers not exceeding 20cm in depth, breaking clods watering,rolling each layer with 1/2 tonne roller, or stone or steelrammers and rolling every 3rd and top- most layer withpower roller of minimum 8-10 tonne capacity and dressing upin embankment for roads, flood banks marginal banks andguide banks or filling up ground depressions, lead up to 50Mtr. and lift up to 1.5 Mtr.:All kinds of soil |
| 3 | CARRIAGE OF MATERIALS Building Rubbish Stone metal (Gritand ballast etc.) |
| 4 | Supplying and Filling in plinth with river sand under floors including watering ramming consolidating and dressing complete including cost of sand |
| 5 | Random rubble dry stone khanranja under floor |
| 6 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M10 grade Nominal Mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). |
| 7 | Providing and laying damp-proof course with cement concrete grade M-150 (1 : 2 : 4) mortar prepared with 1% solution of water-proof compound complete as per specification.75mm thick. |
| 8 | Providing and laying in position specified grade of cement concrete for all RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement. M20 grade Nominal Mix / Design Mix |
| 9 | Providing and laying in position specified grade of cement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcement for Walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc.M20 grade Nominal Mix / Design Mix |
| 10 | Providing M-25 grade concrete by using cement as per codal provision instead of M-20 grade design mix. |
| 11 | Centering and Shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation , footings, strap beam, raft , bases of columns etc. |
| 12 | Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates, anchor blocks, sills, chhajjas, lintel, beam, plinth beam etc. |
| 13 | Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for :Columns, pillars, posts and struts etc. |
| 14 | Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. ('Original producers' who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to IS:1786)Thermo-mechanically Treated bars (Conforming of relevent IS code) |
| 15 | Labour charges for cutting, bending for fabrication andbinding reinforcement (plain or tor/ribbed/TMT steel) as perdrawing and design for R.C.C. and R.B. work including cost ofbinding wire with all lead and lift up to floor five levelcomplete |
| 16 | Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level upto floor V level in all shapes and sizes in : Cement mortar 1 : 4 (1 cement : 4 coarse sand) |
| 17 | Providing and fixing Granite stone slab mirror polished andmachine edge cut in walls, pillars, steps, Shelves, SillsCounters, Floors etc. laid on 12mm (Av.) thick base of cementmortar 1:3 (1 cement : 3 coarse sand) jointing with whitecement mortar 1:2 (1white cement : 2 marble dust) withpigment to match the shade of the marble slab includinggrinding, rubbing and polishing complete.Good quality South Black Above 3601 Cm2 Slabs |
| 18 | Extra for providing edge moulding to 15-18mm thick marble/ Granite/Kota stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-inCharge. Granite/Kota Stone Work Full Edge moulding |
| 19 | P & F 1st qualityHeavy Duty Vitrified Polished Digital tiles on floor, skirting and steps etc.in different sizes (thickness minimum 10mm) with water absortion less than or equal 0.08% and conforming to IS 15622 of approved make in all colour and shade, laid with 20 mm thick CM 1: 4 including grounting the joints with white cement and matching pigment etc complete. Size 600 mm X 1200 mm. |
| 20 | Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formal dehyderesin in glue both sides with approved steelfittings complete as per annexure 'A' :25 mm thick Decorative teak veneer both side |
| 21 | Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formal dehyderesin in glue both sides with approved steel fittings complete as per annexure 'A' :35 mm thick Decorative teak veneer both side |
| 22 | Providing & fixing 12 mm thick tegular edge Glass FibreReinforced Gypsum False ceiling tiles of size 595 x 595 mmin true horizontal level suspended on inter locking metal gridof hot dipped galvanised steel sections ( galvanized @ 170gsm/sqm.) consisting of main “T” runner with suitablyspaced joints to get required length and of size 24x38mmmade from 0.30mm thick (minimum) sheet spaced at1200mm center to center and cross “T” of size 24x25mmmade of 0.30mm thick (minimum) sheet, 1200mm longspaced between main “T” at 600mm center to center to forma grid of 1200x600 mm and secondary cross “T” of length600mm and size 24x25mm made of 0.30 mm thick(minimum) sheet to be interlocked at middle of the1200x600mm panel to form grids of 600x600mm and wall angle of size 21x21x0.30 mm and laying false ceiling tiles of approved texture in the grid including, wherever, required, cutting/making, opening forservices like diffusers, grills, light fittings, fixtures, smokedetectors etc. Main “T” runners to be suspended from ceilingusing GI slotted cleats fixed to ceiling with 6 mm dia and50mm long dash fasteners, 4mm GI adjustable rods withgalvanised level clips spaced at 1200mm center to centeralong main T, bottom exposed width of 24mm of all Tsections shall be pre-painted with polyester paint, allcomplete at all heights as per specifications drawings and asdirected by Engineer-in-Charge. |
| 23 | Supplying and fixing wood work in frames of wall panelling, false ceiling partition wall etc. as per approved design and drawing including antitermite treatment. 8.2.2 Chir wood Grade - I. |
| 24 | Plaster on new surface on walls in cement sand mortar 1:3 including racking of joints etc. complete fine finish : 25mm thick . |
| 25 | Providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete . New Plastered Surface (three or more coats) |
| 26 | Painting exterior surface of Wall with 100% acrylic exteriorpaint of approved brand and manufacture to give an evenshade with two or more coats including prepartion of basewith sand papering, primer, putty, etc complete in all respectincluding scaffolding and safety provision |
| 27 | Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposalof unserviceable material within 50 metres lead as perdirection of Engineer-in-charge: |
| 28 | Providing and fixing of uPVC Sliding windows: Frame Madefrom the Extruded uPVC Window Profile Section of size106w x 50h mm having outer wall thickness of 2.5mm (+/-0.2mm) and 3 box multi-chamber construction, Laminated(colour) finish, duly reinforced with 1.2 mm thick GI section.Frame shall have three track configuration, Vertical memberof frame which bears the sliding shutter load shall havealuminium rail/track for smooth sliding of shutter rollers. Allthe four corners shall be mitered cut & thermal welded so as toform window frame. Frame shall be milled with drain and airequalizer hole in order to be water tight and for drainage ofaccumulated water, if any, to outer side.Shutter : The shutter of sliding window shall be made of 39wx 69h mm Extruded 3 box multi- chamber uPVC WindowProfile Section of laminated (colour) having outer wallthickness of 2.5mm (+/- 0.2mm) provided with reinforcementof 1.5mm thick GI section duly mitered cut & thermal weldedat all corners and fitted with uPVC glazing bead of size 22 x20 mm with inner and outer co-extruded EPDM/TPE-Eweather seal gaskets alongwith 6mm thick ISI make plain floatglass. |
| 29 | Providing and fixing glazing in aluminium door, window ,ventilator shutters and partitions etc. with PVS / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge.(Cost of aluminium snap beading shall be paid in basic item.). With float glass panes of 5.0 mm thickness ( weight not less than 13.50 kg/sqm) |
| 30 | Providing & fixing factory made 100% Solid WPC (WoodPolymer Composite) Door Frame 90mm x 45 mm ( Moulded )Single Rebated,, made from Wood Polymer Composite (SingleExtruded Process) material comparising of virign PVCpolymer of K Value 58-60 ( Suspemsion Grade), CalciumCorbonate and Natural Fibers ( Wood Powder/ Rice Husk/Wheat Husk) and Nor toxic additives fabricated with meterJoints after applying PVC solvent Cement & screwed with fullbody treaded star headed srews having minimum frame densityof 780 kg/ cbm & manufactured by an ISO 9001 - 2015Certified Company, having good screw holding capacity (Screw Withrawal strength of 2200 N ( Face) & 1100 N (Edge), |
| 31 | Anti-termite treatment of existing floor and wall using Imidacloprid 30.5% EC non repellent, odorless, low dose, environimentally safe Termiticide with rapid action non corrosive stain free, by injecting the emulsion as perspecification and plugging with cement mortar 1:2 ( 1 cement : 2 coarse sand) in the whole floor area. The pesticide emulsion of imidacloprid 30.5% EC mixed with water in the ration of 1:474 will be pumped by a motorized spray pump specified manner. The net floor and wall area treated will be measuredfor payment. |
| 32 | Providing & Laying POP Cornice of required design & pattern in ceiling including nailing & scafollding etc. complete with fine finishing of size: 50mm x 50mm |
| 33 | Random Rubble stone masonry for with hard stone infoundation and plinth in Cement Sand mortar above 30 CMthick wall in:Cement Mortar 1:4 ( 1-Cement : 4-Sand). |
| 34 | Providing & Fixing BWR ISI marked 19 mm board ofapproved make for making wardrobe/shelves and otherfurniture with fevicol & nails complete as per approved byengineer in charge. |
| 35 | Providing & Fixing Commercial Ply as per IS 710 : 1976BWR of approved make for making wardrobe/shelves andother furniture with fevicol & nails complete as per approvedby engineer in charge. |
| 36 | Providing & Fixing mica of approved make for inner/outer side of shutters with fevicol & nails complete as per approved by engineer in charge.0.8mm thick mica |
| 37 | Gradin g roof for water proofing treatment with waterproffing compound Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 gradedstone aggregate 20 mm nominal size) |
| 38 | Providing and laying APP (Atactic Polypropylene Polymer)modified prefabricated five layer 3mm thick water proofingmembrane, black finished reinforced with non-wovenpolyester matt consisting of a coat of bitumen primer forbitumen membran @ 0.40 Itr/sq.mt. by the same membranemanufacture of density at 25°C, 0.87-0.89 kg/ltr and viscosity70-160 cps. Over the primer coat the layer of membrane shallbe laid using Butane Torch and sealing all joints etc., andpreparing the surface complete. The vital physical andchemical parameters of the membrane shall be as under Jointstrength in longitudinal and transverse direction at 23°C as650/450N/5cm. Tear strength in longitudinal and transversedirection as 300/250N. Softening point of membrane not lessthan 150°C. Cold flexibility shall be upto -2°C when tested inaccordance with ASTM, D-5147. The laying of membraneshall be got done through the authorized applicator of themanufacturer of membrane.3 mm thick |
| 39 | Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & it's ISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thick Hot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure 'A' Medium point (up to 6 mtr.) |
| 40 | Long point (up to 10 mtr..) |
| 41 | Wiring of 3/5 pin 6 amp. Light plug point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) PVC conduit & it's ISI marked (IS:3419-1988)accessories, Hot Dipped Galvanized Modular box of 1.2 mm thick with earth terminal, 10 A modular switch, 3/5 pin 6 A modular socket, Modular face plate with grid plate, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure 'A' attached with this BSR, On board |
| 42 | Medium point (up to 6 mtr.) |
| 43 | Long point (up to 10 mtr..) |
| 44 | S&F following sizes (dia.) of ISI marked virgin material MMS ( IS:9537 P - III ) PVC conduit along with ISI marked (IS:3419-1988) accessories as required in recess including cutting the wall, covering conduit and making good the same as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR. 20 mm |
| 45 | S&F following sizes (dia.) of ISI marked virgin material MMS ( IS:9537 P - III ) PVC conduit along with ISI marked (IS:3419-1988) accessories as required in recess including cutting the wall, covering conduit and making good the same as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR. 25 mm |
| 46 | 32 mm |
| 47 | Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR, 2 x 1.5 sq.mm |
| 48 | 2 x 2.5 sq. mm. + 1x1.5sqmm |
| 49 | 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. |
| 50 | 2 x 6.0 sq. mm. + 1 x 2.5 sq. mm. |
| 51 | Supply and Laying of PE Insulated jelly filled Armoured Telephone Cable. with 0.6 mm thick Solid Annealed Bare Copper Conductor and confirming to TEC specifications confirming. to DOT GR/CUG-01/Aug.2003 in existing pipe / open trench / Cable tray / on surface including making necessary connection, testing etc. as required of size. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR. 5 pair |
| 52 | Supplying and Laying ISI marked P.V.C. insulated submersible cable as per PWD specification for electrical Works confirming to IS:694 and as per IS8130:2013 of 1.1 kV grade. Wire should be made from 99.99% purity copper, class 5 stranding in acc. to IEC60228 for lower watt loss, oxygen free (<10ppm) for less chances of oxidization and higher silver content for gives better conductivity, insulation PVC typeA, flame retardant as per IS10810-53, better amper agerating as per VDE0298 part 4 including making connection etc. as required. OEMM usthave its own in house NABL lab setup for all testing facilities for wires. All as per pre approved by Engineer in charge, making connections. For additional technical parameters of products/ work, refer Annexure \\"A\\" attached with this BSR .6.0 Sq.mm 3 core flat / Round |
| 53 | Supply and laying following size twin parallel type Speaker cables of IS/ISO 9001 CERTIFIED COMPANY made with multi wire, bright annealed flexible bare electrolytic grade copper conductor, insulated with specially formulated transparent grade PVC compound, red strip for identification in existing conduit etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR. 0.75 sq.mm |
| 54 | P & F 1.00mm thick M.S. Recessed concealed box, round of size 150 mm dia, depth 100 mm complete as required. All as per pre approved by Engineer in charge.For additional technical parameters of product / work refer Annexure 'A' attached with this BSR |
| 55 | P & F 1.2mm thick M.S. Recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mm length extended on each side . All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR |
| 56 | P & F 1.00mm thick M.S. Recessed concealed box, round of size 150 mm dia, depth 100 mm complete as required. All as per pre approved by Engineer in charge.For additional technical parameters of product / work refer Annexure 'A' attached with this BSR |
| 57 | Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load and site requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted in existing distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above rating including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR. Single pole MCB (With B/C curve tripping Characteristics),6 A to 32 A rating. |
| 58 | Double pole MCB(With B/C curve tripping Characteristics). 6 A to 32 A rating |
| 59 | Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load and site requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted in existing distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above rating including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR. Four pole MCB (With B/C curve tripping Characteristics). 40 A rating |
| 60 | Providing & Fixing of 240/415 V isolator ISI marked IS:13947-III/conforming to IEC 60947-3, suitable for AC22A utilization category, 4KV impulse withstand voltage, true contact indication, Red colour dolly / lever shall have single mould covering over all poles for operation , two position din rail mounting, minimum phase termination capacity of 35sq.mm. IP 20 contact protection and fitted in existing distribution board / sheet including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge.For additional technical parameters of product / work refer Annexure 'A' attached with this BSR. Four pole Isolator. 63 A rating |
| 61 | Providing & Fixing of Recessed/surface mounting heavy duty horizontal type Double Door ( Metal / Glazed )Distribution board with Metal end box made out from Galvanized steel / CRCA sheet not less then 1.2 mm thick conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3, powder painted complete with reversible door (for double door DB only )100 amp. insulated copper bus bar/shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar,masking sheet, making internal DB terminations with copper lugs, Ferrules, detachable gland plate, including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR. Metal door (Three phase) IK-09 and IP-43 with Metal end box. 12 Way |
| 62 | Providing & Fixing of modular type switch/ bell push duly ISI marked (IS :3854) with CM/L no. printed and made out of unbreakable and fire retardant vergin UV Stabilized Polycarbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating ,minimum width of switch toggle( PUSH PART ) should not less then 20mm, including all as per pre approved by Engineer in charge,making connections, testing etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR . 16 A one way switch With Led Indicator 10 A one way switch |
| 63 | 10 A two way switch |
| 64 | 16 A one way switch With Led Indicator |
| 65 | 25 Amp. 2 Module switch With Led Indicator |
| 66 | 32 Amp. 2 Module switch With Led Indicator |
| 67 | Providing & Fixing of modular type lockable feature socket duly made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating ,including all as per pre approved by Engineer in charge,making connections, testing etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR6 A 3/5 pin shuttered socket |
| 68 | 6/16 A shuttered socket |
| 69 | 25 Amp. 2 Module Socket |
| 70 | Providing & Fixing of modular type 120 W Step Fan regulator duly ISI marked (IS 11037:1984 ) with CM/L no. printed made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating , including all as per pre approved by Engineer in charge,making connections, testing etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR. 5 step fan regulator 2 Module 360 dgree rotating |
| 71 | Providing & Fixing of following modular accessories as per PWD specification for electrical Works, made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating , including all as per pre approved by Engineer in charge,making connections, testing etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR. RJ-11 telephone jack single line |
| 72 | USB Charger 1 A - 1 M with BIS mark |
| 73 | RJ-45, Cat 6 computer jack with shutter |
| 74 | T.V. coaxial socket |
| 75 | Blanking plate |
| 76 | Providing & Fixing of following size mounting grid plates with cover plates made from fire retardent UV established high performance engineering plastic suitable for all universal metal boxes for front installation & removal direct fit type complete in all respect.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR .1/2 Module 3 Module |
| 77 | 4 Module |
| 78 | 6 Module |
| 79 | 8 Module |
| 80 | Providing & Fixing of Wiring Accessories OEM fabricated following size GI box of 1.2 mm thick with earthing terminal and adjustable floating clamp in recess/ surface suitable for modular accessories as required.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR .1/2 Module |
| 81 | 3 Module |
| 82 | 4/5 Module |
| 83 | 6 / 8 module |
| 84 | Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Arrmoured Aluminium cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with H4- Grade electrolytic aluminium conductor confirming to IS 8130 of purity >99.6 %, round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie) including testing etc. as required of following size. OEM must have it's own in house NABL accrediated Laboratory for testing procedure as per IS:10810.For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 10.0 Sq. mm 4 core |
| 85 | Providing & Fixing of BEE Star rated copper wounded double ball bearing capacitor start, aluminium body & Metallic blade ceiling fan Conforming to all the performance requirements laid down in IS 374:2019 including all amendments, as applicable ; & Carry BIS licensing (i.e. ISI marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . 1200 mm Sweep BEE 3 Star rated (service value >=5.0 to< 5.5 ) |
| 86 | Providing & Fixing of Heavy duty capacitor start, copper wound Double ball bearing 900/1400 RPM single phase Exhaust fan conforming to IS:2312 ISI marked in existing opening including making connections testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . 300 mm sweep(900/1400 RPM) |
| 87 | Surface Mounting (with extruded alumn. Housing ). Minimum lumen output 1300 lm |
| 88 | Providing & Fixing of IP 20 box made out from 1.2mm thick CRCA sheet steel with depth of minimun 30 mm and finished with powder coating and suitable for mounting LED tube including side covers, holders , internal wiring to illuminate the single sided connection LED tube. ( Without tube). All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . Suitable for 4' LED Tube shape fixture for single rod |
| 89 | Supply & Fixing of Dry Powder Agent (as per IS 4308:2019), ABC type Fire Extinguisher (Stored Pressure type) conforming to IS:15683:2018 , Powder coated Internal & External Surface Deep drawn cylinder body of Mild Steel CR2 grade conforming to IS: 513, Squeeze grip Forged brass release valve with Inbuilt safety release device, Diaphragm Type, 0 to 28 bar range pressure gauge, 450 mm long EPDM discharge tube, QR code for Product Traceability including Fixing on wall with suitable Anchor Fasteners as required of following capacity. Test Certificates of all the Parameters along with Hydro test & Burst test (For Cylinder Body) Certificate from OEM / External NABL Accrediated Lab is to be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . 6 kg |
| 90 | Supply , Installation, Testing and Comissioning of Air Cooled Cassette type Air conditioners complete with Indoor unit(IDU), Out door unit (ODU), R-32/R410A Green Refrigerant, wireless Remote, inbuilt drain pump, suitable for 400/230V, +/- 10% 50 Hz ,1 /3 phase AC supply, apable of performing cooling, dehumidification, Air circulation, filteration & ventilation of following capacity with Scroll /rotary/twin rotary compressor. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . Non Inverter 2.0 TR ISEER not less then 3.0 3.0 TR |
| 91 | Supply , Installation, Testing and Comissioning of Air Cooled Cassette type Air conditioners complete with Indoor unit(IDU), Out door unit (ODU), R-32/R410A Green Refrigerant, wireless Remote, inbuilt drain pump, suitable for 400/230V, +/- 10% 50 Hz ,1 /3 phase AC supply, apable of performing cooling, dehumidification, Air circulation, filteration & ventilation of following capacity with Scroll /rotary/twin rotary compressor. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . Non Inverter 3.0 TR |
| 92 | Providing & Fixing of IK10 IP65 / IP66 protected LED Up - Down Luminarie Wall / Surface mounting made of powder coated die cast alluminium housing with UV stabalized PC diffuser. The System level Luminous efficacy ≥ 90 Lumen/W. COB LEDs is to be used, System CRI>70, CCT: 3000/4000/6500 K. The integral electronic driver must be potted & has a unique BIS R number constant current and Internal/external surge protection device of min. 4KV(L-N) and efficiency > 85%, PF>0.9, THD<10% and input Voltage range of 140-270V AC at 50Hz. System life of 50000 Burning hours with 70% of Initial Lumens maintainedLight output in Cool white or Warm White Colour as per engineers choice. driver current <750mA. Fixture must be in compliance with BIS Standards and Trade mark Certificate complete in all respect.OEMMust have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , referAnnexure \\"A\\" attached with this BSR .18.15.2 Minimum lumen output 1300 lm Up-Down Luminary |
| 93 | Providing and fixing in position on wall or on ply Aluminium Sheet before fixing fixed it on wall. |
| 94 | Providing and fixing in position wall panelling with good finishing 12mm block board with designer Laminate over 12mm ply backing. Opening to be provided for electrical fixtures and other services where ever required complete with cleaning and good finishing as per design drawings, specifications . Make : Century, Merino,Royal touch, Wood line or equivalent. |
| 95 | Providing and fixing Merino Panel 20mm wall panelling comprising of Merino panel / ply strip/ impailer clips, fixed over prepared surface including necessary cutting, edge finishing, alignment, fastening and complete in all respects as per approved design and direction of Engineer-in-Charge. |
| 96 | Providing and fixing in position with WPC moulding with complete Paint Finish with cleaning and good finishing as per design drawings, specifications size smaller or equivalent then 50 mm X 50 mm |
| 97 | Making Grooves and Finish with Polish as per design size upto 06x06 mm in position with complete stain and good finishing along with cleaning. |
| 98 | Providing and fixing in position Edge bend on Veneer and laminate edges for good finishing along the corners. |
| 99 | Providing and fixing in position good quality blinds with material which is thick with black out features . |
| 100 | Making Grooves and Finish with Paint as per design size upto 06x06 mm in position with complete all side polish and good finishing along with cleaning. |
| 101 | Cabinet made of Laminate: Providing and fixing in position cabinet made of good quality Ply with Laminate finish as per design. |
| 102 | Director's /Head Chair : High Back revovling Chair make with leathrette finish seat and back and Handle should be proypylone finish Pedestal make with PVC finsh with nylon twin wheel.Dia-600 and RTM mechansim . |
| 103 | Executive Chair : High Back revovling Chair make with leathrette finish seat and back and Handle should be proypylone finish Pedestal make with PVC finsh with nylon twin wheel.Dia-600 and RTM mechansim . |
| 104 | Visitor Chair :Mid Back revovling Chair make with leathrette finish seat and back and Handle should be proypylone finish Pedestal.Dia-600 . |
| 105 | Providing and fixing Wall Lamp light |
| 106 | Providing and fixing COVE light Please Enable Macros to View BoQ information |
