|
| 1 | Schedule-A |
| 2 | Demolition of Cement Concrete (un-reinforced) of any description, not exc. 150mm thickness (above or below Ground Level) and removing the same from Site(s),complete all as specified and directed by Engineer-in-Charge. |
| 3 | M&L for 20 mm thick rendering in CM 1:4 on brick/concrete surfaces of sunken slab, mixed with liquid water proofing compound both floor and wall of sunken slab, the surface shall be cured and allow to dry, finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. . Note :- Water proofing compound shall be measured & paid separately. |
| 4 | Supply only liquid water proofing compound complete all as specified and directed by Engineer-in-Charge. |
| 5 | M&L applying evenly two coat cemetious/liquid waterproofing coating on sunken slab/ceiling/wall as per manufacturer instructions including cleaning surfacecomplete all as specified and directed by Engineer-in-Charge. |
| 6 | M&L for PCC 1:5:10 type E2 Using 40mm graded stone aggregate as in filling under floor/sunken slab all as specified complete all as specified and directed by Engineer-in-Charge. |
| 7 | M&L Cement Concrete type B1,1:2:4 (20mm Graded Stone Aggregate) 25 mm thick, as in Floors, etc., and finished the Cement Concrete Surfaces Even and fair with using Extra Cement, complete all as specified and directed by Engineer-in-Charge. . |
| 8 | S & F vitrified tiles tiles light shade 10mm thick (square/rectangular) polished, area of each tile n.exc. 0.36 sqm, in floor etc.,set and jointed in neat cement slurry over & including 15mm thick screed bed in CM 1:4 and pointed in white or coloured cement with pigment to match for laying floor fineshes & including Dismantling of old vitrified tile including cement morter bedding (but not backing), removing tiles and rubbish off the premises. Complete all as specified and directed by Engineer-in-Charge. . |
| 9 | M&L for Ceramic coloured/ printed non-skid tiles of size 7-8 mm thick( square / rectangular ) area of each tile exceeding 0.11 Sqm but n. exec. 0.18 Sqm laid as in floors setting and jointed with neat cement slurry over & including 15 mm thick screed bedding layers of cement sand mortar ( 1:4) and pointed with coloured cement to match with surfaces of tiles & including Dismantling of old Ceramic coloured/ printed non-skid tiles of any thickness including cement morter bedding (but not backing), removing tiles and rubbish off the premises. Complete all as specified and directed by Engineer-in-Charge. |
| 10 | M&L Glazed Ceramic Coloured Tiles, 450x350x7mm thick, set on Vertical Surfaces such as Skirting, Dado, etc,over and including 10mm thick rendering in cement mortar 1:4 Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the shade of the Tiles, & including Dismantling of old tiles of any thickness including cement morter bedding (but not backing), removing tiles and rubbish off the premises.complete all as specified and directed by Engineer-in-Charge. n |
| 11 | M&L for brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mean radius built in cement mortar 1:4 including Demolition of brick work or stone/boulders masonry, built in cement mortar or cement lime mortar, complete all as specified and directed by Engineer-in-Charge. |
| 12 | M&L for 20mm thick pre polished granite (any colour) slab laid over & including 15 mm thick CM 1:4 bedding in door Chowkhat/Frame, Window Cill, plateform floor and skirting/dado surface and jointed with grey cement slurry and pointed in white cement with pigment to match the shade of granite stone including Moulding/rounding and polishing & dismantling of the old stone and tiles of any description or thickness complete all as specified and directed by Engineer-in-Charge. . |
| 13 | Taking down Cement Plaster from wall and ceiling of any description from Brick/concrete surfaces including raking out Joints, hacking for Key, scrubbing down with Water, etc., and removing same from the Site(s),complete all as specified and directed by Engineer-in-Charge. |
| 14 | M&L for 10 mm thick rendering in CM 1:3 on concrete/gunniting surfaces as in ceiling mixed with integral water proofing compound , the surface shall be cured and allow to dry, finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. . Note :- Water proofing compound shall be measured & paid separately.. |
| 15 | M&L for 15 mm thick rendering in CM 1:6 on brick/concrete surfaces of wall, mixed with integral water proofing compound, the surface shall be cured and allow to dry, finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. . Note :- Water proofing compound shall be measured & paid separately. |
| 16 | M&L for preparation of newly plastered surfaces of walls by Vacuum based sanding machine complete all as specified, applying wall care putty min 2mm thick (multi purpose mixer shall be used for uniform and proper mixing of putty) and applying two coats oil emulsion distemper white or coloured including primer by auto roller complete complete all as specified and directed by Engineer-in-Charge. |
| 17 | M&L for preparation of newly plastered surfaces of ceiling by Vacuum based sanding machine complete all as specified, applying wall care putty 2mm thick (multi purpose mixer shall be used for uniform and proper mixing of putty) and applying two coats oil emulsion distemper white or coloured including primer by auto roller complete all as specified and directed by Engineer-in-Charge. . |
| 18 | M&L for complete removal of plastered or un plastered old decorated surfaces of walls by Vacuum based sanding machine all as specified, removal of nails etc providing 2mm thick wall care putty (multi purpose mixer shall be used for uniform and proper mixing of putty), primer and applying two coat oil emulsion distemper white or coloured by auto roller complete all as specified & directed by Engineer-in-Charge. |
| 19 | M&L for complete removal of plastered or un plastered old decorated surfaces of ceiling by Vacuum based sanding machine all as specified,providing 2mm thick wall care putty , primer and applying two coat oil emulsion distemper white or coloured by auto roller complete all as specified and directed by Engineer-in-Charge. |
| 20 | M&L for preparation of old painted surfaces of wood & wood based surface of any description not otherwise described over 10 cm width & girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge. |
| 21 | M&L for preparation of old painted surfaces of steel & steel based surface of any description not otherwise described over 10 cm width & girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge. |
| 22 | Taking down chowkhat or frames with shutters (without taking off shutters from the frame) n.exc. 1.5 Sqm each complete all as specified and directed by Engineer-in-Charge. |
| 23 | All as above Item no 21 but exceeding 1.50 sqm each and n.exc. 4 Sqm each complete all as specified and directed by Engineer-in-Charge. |
| 24 | Taking down shutters only exc 1 Sqm and n.exc. 2 Sqm each , complete all as specified and directed by Engineer-in-Charge. |
| 25 | S&F 35 mm thick factory made flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both the faces.complete all as specified and directed by Engineer-in-Charge. |
| 26 | M&L for 35 mm thick IInd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed by Engineer-in-Charge. |
| 27 | Taking down old door shutter exc 1 sqm and n exc 2 sqm each ,easing and adjusting and refixing in same opening after making the door fully functional complete all as specified and directed by Engineer-in-Charge. |
| 28 | Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead /double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multi-chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality,& incluing taking down of old window of any description ,complete all as specified and directed by Engineer-in-Charge. |
| 29 | S&F in repair Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed by Engineer-in-Charge. |
| 30 | S&F Anodised aluminium window and ventilator shutters, side hung type or sliding without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) 100mm long aluminium handle (1 no.) 100mm long Aluminium Tower bolt 2 No complete all as specified and directed by Engineer-in-Charge. |
| 31 | S & F Factory made single extruded WPC (Wood Polymer Composite) solid door Frames/ Chowkhat of size 50x75 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp- ressive strength of 58 N/mm², modules of elasticity 900 N/mm² and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length , complete all as specified and directed by Engineer-in-Charge. |
| 32 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm², modulus of elasticity 850 N/mm² and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed by Engineer-in-Charge. |
| 33 | S&F in repair 18/19 mm thick WPC (Wood Plastic Composite) board, exterior grade, termite & borer proof, water resistant, factory finished, fixed with stainless steel screws as in cupboard shutters, shelves, pelmet boxes and kitchen cupboard works , with beading suitable for edge of shutter/cupboards etc., including all necessary fittings, including taking down old board of any type and any thickness .complete all as specified and directed by Engineer-in-Charge. |
| 34 | S&F in repair 18/19 mm thick prelaminated particle board exterior gde prelaminated one side with decorative choice and other side white lamination fixed with screws as in cup board shutters & shelves and pelmet boxes etc complete all as specified and directed by Engineer-in-Charge. |
| 35 | S&F 100 mm long,designer pattern Stanless Steel handles for fixing in cupboards complete all as specified and directed by Engineer-in-Charge. |
| 36 | S&F in repair, Magnet catch for fixing in cup board complete all as specified and directed by Engineer-in-Charge. |
| 37 | S&F , 75 mm long aluminium alloy butt hinges complete all as specified and directed by Engineer-in-Charge. |
| 38 | Taking down old defective Aluminum windows of any description size not exc. 2.50 sqm area , including necessary repair to glass pane/rubber beading/aluminum glazing clip if necessary/locking system/ incl.necessary sliding rollers for rolling and adjustment etc and refixing in same location complete all as specified and directed by Engineer-in-Charge. Note :- Glass Pane/rubberbeeding/aluminum beeding will be measured and paid separately under subsequent items. |
| 39 | S & F in repair rubber beeding to be fixed over glass panes in Aluminum widows complete all as specified and directed by Engineer-in-Charge. |
| 40 | S&F in repair, aluminum anodised glazing clip to the alumiinum window frames after fixing the glass panes complete all as specified and directed by Engineer-in-Charge. |
| 41 | Dismantling structural steel work incl. steel door,gate,window guard bars,grills etc.complete all as specified and directed by Engineer-in-Charge. |
| 42 | M&L fabricated frame work as in doors of gate of angle iron or other section with gusset plate rails, braces etc. complete drilled for fixing steel sheeting or other covering door etc to be prepared for hanging with and including hinges .complete all as specified and directed by Engineer-in-Charge. |
| 43 | M&L for mild steel works as in grills and railing of Fe-410-0or Fe 310-0,complete all as specified and directed by Engineer-in-Charge. |
| 44 | M&L PCC for 1:2:4 type B-1 (using 20mm graded stone aggregate) as in coping, benching & for fixing railing, holdfast etc complete all as specified and directed by Engineer-in-Charge. . |
| 45 | Demolition of reinforced cement Concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engineer-in-Charge. |
| 46 | M&L Reinforced cement concrete (nominal mix , 1:2:4 B1 20 mm graded agg )in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engineer-in-Charge. |
| 47 | M&L Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed by Engineer-in-Charge. |
| 48 | M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge. |
| 49 | Hacking out old broken glass (any th size, quality or description) from wooden or steel frames glazed with putty or fixed with wooden beads complete all as specified and directed by Engineer-in-Charge. . |
| 50 | S&F Figured Glass pin head type 4.0mm thick, fixing to Aluminium Sections as in Panel of Doors, Windows Shutters and Panelling Works with necessary fixing Arrangements viz Jointing Cleats, Glazing Clips, Rubber Packing, Screws, etc., as required/ordered at Site(s), complete all as specified and directed by Engineer-in-Charge. |
| 51 | S&F Sheet Glass ordinary 4.0mm thick, fixing to Aluminium Sections as in Panel of Doors, Windows Shutters and Panelling Works with necessary fixing Arrangements viz Jointing Cleats, Glazing Clips, Rubber Packing, Screws, etc., as required/ordered at Site(s), complete all as specified and directed by Engineer-in-Charge. |
| 52 | S&F in repair for Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of apoerture 1.40mm and fixed with aluminium/wooden/steel beads complete all as specified and directed by Engineer-in-Charge. . |
| 53 | S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of apoerture 1.40mm and fixed with aluminium/wooden/steel beads complete all as specified and directed by Engineer-in-Charge. . |
| 54 | S&F MS/SS medium weight cold rolled butt hinge ISI Marked 100mm size, fixed with screw complete all as specified and directed by Engineer-in-Charge. |
| 55 | S&F in repairs, MS Helical door spring 300 mm long complete all as specified and directed by Engineer-in-Charge. (Note:-Helical spring will be fixed by welding) |
| 56 | S&F butt hinge stainless steel 100/150mm size , fixed with stainless steel screw complete all as specified and directed by Engineer-in-Charge. |
| 57 | S&F extruded anodised aluminum alloy handle 150mm long fabricated type , complete all as specified and directed by Engineer-in-Charge. |
| 58 | S&F anodised aluminum barrel tower bolt of extruded section 150mm long, complete all as specified and directed by Engineer-in-Charge. |
| 59 | S&F aluminum alloy sliding door bolt 300mm long with hasp, staple (bolt type) adnd fixing clips of sheets, cast of exctruded sections and fiing bolts or extruded section complete all as specified and directed by Engineer-in-Charge. |
| 60 | S&F telescopic drawer channel 16''/18\\" long complete all as specified and directed by Engineer-in-Charge. |
| 61 | S & F in repair floor door stopper of size 140 mm long aluminium alloy body and tongue, anodized with hard drawn steel spring incl cleats etc fixed to door.complete all as specified and directed by Engineer-in-Charge. |
| 62 | S&F in repairs 25mm dia stainless steel curtain rods including cutting and fixing complete all as specified and directed by Engineer-in-Charge. |
| 63 | S& F in repairs Stainless Steel wall bracket suitable for 25mm dia curtain rods, complete all as specified and directed by Engineer-in-Charge. |
| 64 | S& F in repairs Stainless Steel designer pattern side knobs suitable for 25mm dia curtain rods complete all as specified and directed by Engineer-in-Charge. |
| 65 | M&L preparation of new or previously untreated surfaces of wood of any description not exceeding 10cm width or girth and applying two coats of synthetic enamel paint over & incl one coat of pink primer complete all as specified and directed by Engineer-in-Charge. |
| 66 | M&L preparation of new or previously steel surfaces of any description not exceeding 10cm width or girth and applying two coats of synthetic enamel paint over & incl one coat of red oxide primercomplete all as specified and directed by Engineer-in-Charge. . |
| 67 | S&F continuous (piano) hinges, mild steel bright finish of 40 mm width of flaps(when open) complete all as specified and directed by Engineer-in-Charge. . |
| 68 | S&F in repairs aluminum door seal fixed to bottom of door shutters complete all as specified and directed by Engineer-in-Charge. |
| 69 | S&F 110mm dia PVC SWR pipe laid to wall and floor and fixed with clamp and icluding dismantling of old existing PVC/CI/concrete pipes 100mm dia of any description, jointed in cement mortar and removing to store.complete all as specified and directed by Engineer-in-Charge. |
| 70 | S&F 75mm dia PVC SWR pipe laid to wall and floor and fixed with clamp and icluding dismantling of old existing PVC/CI/concrete pipes of any description, jointed in cement mortar and removing to store.complete all as specified and directed by Engineer-in-Charge. |
| 71 | S&F 32mm dia PVC SWR pipe laid to wall and floor and fixed with clamp and icluding dismantling of old existing PVC/CI/concrete pipes of any description, jointed in cement mortar and removing to store.complete all as specified and directed by Engineer-in-Charge. |
| 72 | S&F in repair 32mm dia PVC SWR Bend ,complete all as specified and directed by Engineer-in-Charge. |
| 73 | S&F in repair 100/75mm dia PVC SWR Bend ,complete all as specified and directed by Engineer-in-Charge. |
| 74 | S&F in repair 110mm dia PVC SWR Bend , complete all as specified and directed by Engineer-in-Charge. |
| 75 | S&F in repair 110/75mm dia PVC SWR Junction Single (Tee) ,complete all as specified and directed by Engineer-in-Charge. |
| 76 | M&L for replacement of 75mm outlet PVC(SWR) floor/nahani trap with steel grating including jointing and breaking/ dismantling any type of floor and making good cement concrete to the B-1 (1:2:4) and testing after repairs and taking down existing trap etc complete all as specified and directed by Engineer-in-Charge. |
| 77 | S&F Galvanised Steel Water Tubing 15mm Bore (dia), ‘Medium Grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situation including Taking up or down unserviceable Steel Water Tubing with Fittings and Connections, etc., complete all as specified and directed by Engineer-in-Charge. |
| 78 | S&F Galvanised Steel Water Tubing 20mm Bore (dia), ‘Medium Grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situ-ation including Taking up or down unserviceable Steel Water Tubing with Fittings and Connections, etc., complete all as specified and directed by Engineer-in-Charge. |
| 79 | S&F Centre hole Brass CP mixer for mixing hot & cold WHB Mixer 15mm Bore (dia) screwed down for iron pipe and fixed including taking down unserviceable WHB Mixer of any description, complete all as specified and directed by Engineer-in-Charge. |
| 80 | S&F Wall Mixer for kitchen sink 15mm Bore (dia) brass chromium plated for mixing hot & cold, as Approved, fixing including Taking down unserviceable Wall Mixer of any description, complete all as specified and directed by Engineer-in-Charge. |
| 81 | S&F Wall Mixer 15mm Bore (dia) brass chromium plated for mixing hot & cold, as Approved, fixing including Taking down unserviceable Wall Mixer of any description, complete all as specified and directed by Engineer-in-Charge. |
| 82 | S&F in repairs Brass CP fancy type Bib Cock 15mm Bore (dia), Chromium Plated Long Body, screwed down, screwed for Iron Pipe or for Brass Ferrule, complete all as specified and directed by Engineer-in-Charge. |
| 83 | S&F in repairs Angle Stop Cock 15mm Bore (dia), fancy type,Chromium Plated, screwed down, screwed for Iron Pipe or for Brass Ferrule etc complete all as specified and directed by Engineer-in-Charge. |
| 84 | S&F Brass CP Health Faucet with 1.00m long tube and holder as Approved, including Taking down un serviceable Health Faucet of any description,complete all as specified and directed by Engineer-in-Charge. |
| 85 | S&F SS Chromium Plated Towel Rail 600mm Long and 20mm dia, as Approved, fixed including Taking down un serviceable Towel Rail of any description, complete all as specified and directed by Engineer-in-Charge. |
| 86 | S&F in repairs stop valve CP 15mm bore (Concealed type), cast copper alloy, screwed down, high pressure with long shank or butterfly handle screwed both ends for iron pipe or union and complete all as specified and directed by Engineer-in-Charge. |
| 87 | S&F in repairs Vitreous China White Wash down Water Closet Pan (Pedestal Pattern) including Bolts, (excluding Flushing Cistern and Flushing Pipe) including seat and seat cover, Making Good disturbed Surfaces with Cement Mortar 1:3,complete all as specified and directed by Engineer-in-Charge. |
| 88 | S&F PVC Flushing Cistern 10 LITRE capacity, Low Level Valve Less, Symphonic Action type, White, with Inlet, Ball Valve, Float and Handle including PVC Flush Pipe of polythene 32mm dia for Low Level Flushing Cistern including Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 and fixed including Taking down/out Unserviceable Flushing Cistern and connected Items, .complete all as specified and directed by Engineer-in-Charge. . |
| 89 | M&L Vitreous China White Wash down Water Closet Pan (Wall mounted type) including Bolts, (including Flushing Cistern and Flushing Pipe) integrated type with white Plastic Seat cover, and Cover including Mild Steel Chromium Plated or Aluminium Hanging Device fixed-in-repairs, including Making Good disturbed Surfaces with Cement Mortar 1:3, complete all as specified and directed by Engineer-in-Charge. |
| 90 | S&F Vitreous China 550x400mm Size Oval Shaped Wash Hand Basin White with 32mm dia Brass Chromium Plated Waste Fitting, including Cutting Chase cutting in wall and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 and fixed including Taking down Unserviceable Wash Hand Basin and connected Items, complete all as specified and directed by Engineer-in-Charge. . |
| 91 | S&F in repair 32 mm bore chromium plated bottle trap for wash hand basin with inlet & outlet screwed for iron pipes or connection including necessary packing , union and cap complete all as specified and directed by Engineer-in-Charge. |
| 92 | S&F in repair, 6mm thick glass corner shelf (12\\"x12\\") with C type Brass CP bracket, complete all as specified and directed by Engineer-in-Charge. Make-Nixo/Hilife or equivalent out of makes specified in list of makes. |
| 93 | S&F High pressure PVC connections pipe 600mm long suitable for Hot and Cold water for 15mm size with Brass CP Check nutcomplete all as specified and directed by Engineer-in-Charge. |
| 94 | M&L for 6mm thick Plywood 6mm thick, BWR Grade, type BB fixed with Screw including taking down old plywood of any description in the wall etc including two coat synthetic enamel paint over a coat of primer complete all as specified and directed by Engineer-in-Charge. . |
| 95 | S&F in repairs, Looking mirror of selected quality, of size 900 mm x 600 mm x 6 mm thick, having four holes on corners and fixed to walls with 20mm SS Stud with CP Brass screws fixed in wooden Gutties/Rawl Plug complete all as specified and directed by Engineer-in-Charge. |
| 96 | S&F in repair (HDPE) water storage LOFT Tank 200 Ltrs capacity in kitchen, hoisted and fixed in position all specified in MES Schedule Part-I, including tank nipple, union and lowering of unservicable Water Storage Tank including dismantling of old water tank complete all as specified and directed by Engineer-in-Charge. |
| 97 | S&F in repairs ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed 15 mm bore complete all as specified and directed by Engineer-in-Charge. |
| 98 | S&F in repairs toilet paper holder of stainless steel fixed to wall with CP brass screws complete all as specified and directed by Engineer-in-Charge. |
| 99 | S&F sinks with drainage board made of stainless steel l mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 1040 x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed by Engineer-in-Charge. |
| 100 | S&F in repair, Brass CP soap dish complete all as specified and directed by Engineer-in-Charge. . |
| 101 | S&F in repair stainless steel grating round /circular with waste hole or without waste hole of dia 75mm/ 100mm size of stainless steel complete all as specified and directed by Engineer-in-Charge. . |
| 102 | S&F as in repair over head shower 150mm square size cast copper alloy, chromium plated, fancy type, with swivel joint fixed to 15 mm bore iron pipe complete all as specified and directed by Engineer-in-Charge. |
| 103 | S&F in repair waste coupling fitting brass chromium plated of 32 mm dia for wash hand basin with long screwed sanks and fly nuts flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engineer-in-Charge. . |
| 104 | S&F in repair waste cupling fitting 75/100 size along with 40 dia waste pipe for SS sink with long screwed shanks and fly nuts flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engineer-in-Charge. . |
| 105 | Removal of debris/malwa to a distance exc 10 Km but n exc 15.00 Km out side MD land and filling in low lying area complete all as specified and directed by Engineer-in-Charge. |
| 106 | Taking down copper/aluminium point wiring (light points) complete, including fixtures and fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit (credit for the above items should be made as per conditions seperately) and making good disturbed surfaces of walls. floors, etc. complete all as directed |
| 107 | Taking down copper/aluminium submain wiring single core 1.5 sqmm,2.5 sqmm, 4 sqmm 3 wire complete, including conduits of any kind, and removing materials to store for keeping in safe custody or for taking credit (credit for the above items should be made as per conditions seperately) and making good disturbed surfaces of walls. floors, etc. complete all as directed |
| 108 | Taking down copper/aluminium submain wiring 6 sqmm 6 wire complete, including conduits of any kind, and removing materials to store for keeping in safe custody or for taking credit (credit for the above items should be made as per conditions seperately) and making good disturbed surfaces of walls. floors, etc. complete all as directed |
| 109 | Taking down main switches, distribution boards etc of any type and capacity along with the existing boards, and removing the same from site and making good the disturbed surfaces/portion of walls etc. all as directed. |
| 110 | Taking down of serviceable ceiling fans, sealing cable and dismantling blades for keeping in store as salvage as directed and specified by Engineer-in-charge. |
| 111 | Taking down of serviceable metal body exhaust fan and refixing the same on same position including cleaning and painting if reqd after the work is over. |
| 112 | Taking down water heater storage type electric capacity 25 liters and refixing the same after repair of the bldg on same location including cleaning of the geyser body complete. |
| 113 | M & L for point wiring (concealed on wall & surface/concealed on cealing) for one light/fan/exhaust fan controlled by one modular/piano switch one way in different locations/building including rigid non metallic PVC conduit, medium grade, ISI marked , 20 mm dia, with 1.5 sqmm FRLS PVC insulated & sheathed cable , stranded copper conductor of 1.5 sqmm as continuous earth connected to common earth dolly, complete all as specified and directed by Engr-in-charge. |
| 114 | All as per item No 112 above but for 5 Amps 5 Pin socket outlet on the same board |
| 115 | All as per item No 112 above but for 5 Amps 5 Pin socket outlet on independent board |
| 116 | All as per item No 112 above but One bell/buzzer point controlled by on bell push |
| 117 | All as per item No 112 above but One light point controlled by two 2- way switches with cables 1.5 sqmm size copper wire. |
| 118 | All as per item No 112 above but one 5 pin, 15 Amp socket outlet on independent board for power point with 2.5 sqmm size copper wire |
| 119 | S& F ceiling rose, 2 to 3 terminals complete all as specified and as directed . |
| 120 | S&F Modular switch, one way 6 Amps , 1 module as specified. |
| 121 | S&F Modular Socket , 6 A-2/3 Pin combined 2 module all as specified and directed. |
| 122 | S&F in replacement of switch modular one module 2 way 6Amps complete all as specified and directed. |
| 123 | S&F twin socket modular type heavyduty out let 6 pin 6/16 Amps 2 module, |
| 124 | S&F switch Modular type 16 Amps , single pole one way 240 volts one module as specified. |
| 125 | S&F Modular Fan step Regulator Bell ,120 W-2 module as specified. |
| 126 | M&L for metal flush box for fixing of switches for 1/2 module |
| 127 | M&L for metal flush box for fixing of switches for 3 module |
| 128 | M&L for metal flush box for fixing of switches for 4 module |
| 129 | M&L for metal flush box for fixing of switches for 6 module |
| 130 | M&L for metal flush box for fixing of switches for 8 module |
| 131 | Supply & fix Modular White cover plate with frame for 1/2 module |
| 132 | Supply & fix Modular White cover plate with frame for 3 module |
| 133 | Supply & fix Modular White cover plate with frame for 4 module |
| 134 | Supply & fix Modular White cover plate with frame for 6 module |
| 135 | Supply & fix Modular White cover plate with frame for 8 module |
| 136 | S&F Modular type blank plate , 1 module as specified. |
| 137 | Supply & fix sheet metal enclosure for 220 volts 20 Amps with a three pin and earth plug top with socket and one single pole MCB 20 amps complete as well as specified and directed. |
| 138 | Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and as directed. |
| 139 | S&F Sheet metal enclosure DD SPN 240 Volts 04 way DB with 200 Amps rated busbar complete all as specified and directed. |
| 140 | S&F TPN DB 415 Volts 8 way double door type DB complete all as specified and directed. |
| 141 | S & F MCB SP of rating, 06 to 32 Amp,240 volt, 10 KA 'B' Series type complete all as specified and as directed. |
| 142 | S & F MCB TPN 63 Amps 415V 10KA 'B' curve miniature circuit breaker current carrying capacity in the DB complete with connection testing and ommissioning complete all as specified and as directed. |
| 143 | M&L for concealed sub main wiring three run of 1.5 sqmm PVC insulated unsheathed copper conductor cable ISI marked 1100 volts grade drawn in and including PVC surface conduit suitable size of medium grade fixed on wall/ceiling/passing through wall etc connected as required at site complete all as directed. Note- (a) Two runs of single core cable with one run of earth continuity cable including PVC conduit and its accessories will be measured and paid as one unit). (b) Make disturbed surface good to wall/floors as existing surface. |
| 144 | M&L for concealed sub main wiring three run of 2.5 sqmm PVC insulated unsheathed copper conductor cable ISI marked 1100 volts grade drawn in and including PVC surface conduit suitable size of medium grade fixed on wall/ceiling/passing through wall etc connected as required at site complete all as directed. Note- (a) Two runs of single core cable with one run of earth continuity cable including PVC conduit and its accessories will be measured and paid as one unit). (b) Make disturbed surface good to wall/floors as existing surface. |
| 145 | M&L for concealed sub main wiring Six run of 06 sqmm PVC insulated unsheathed copper conductor cable ISI marked 1100 volts grade drawn in and including PVC surface conduit suitable size of medium grade fixed on wall/ceiling/passing through wall etc connected as required at site complete all as directed. Note- (a) Four runs of single core cable with two run of earth continuity cable including PVC conduit and its accessories will be measured and paid as one unit). (b) Make disturbed surface good to wall/floors as existing surface. |
| 146 | M&L for concealed sub main wiring three run of 04 sqmm PVC insulated unsheathed copper conductor cable ISI marked 1100 volts grade drawn in and including PVC surface conduit suitable size of medium grade fixed on wall/ceiling/passing through wall etc connected as required at site complete all as directed. Note- (a) Two runs of single core cable with one run of earth continuity cable including PVC conduit and its accessories will be measured and paid as one unit). (b) Make disturbed surface good to wall/floors as existing surface. |
| 147 | S & F RCCB Double pole, 100mA of rating, 40 Amp,240 volt, 100 mA complete all as specified and as directed. |
| 148 | S&F Modular switch, one way 6 Amps Bell push, 1 module as specified. |
| 149 | S&F Bell, AC, 230 volts, single pole as specified. |
| 150 | Supply and fixing ceiling fans complete with blades, down rods 1800mm long , electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with remote operated brushless direct current motor (BLDC) complete all as specified and as directed. |
| 151 | Supply and fix PVC ventilating fan AC single phase 230/240 volts of size 200 mm sweep with louvers and connecting up including provision of cable from ceiling rose to connector to exhaust fan also including make suitable size hole on wall/window as per site requirement. |
| 152 | Supply and fixing exhaust fan, steel body AC single phase, 230 V of size 300 mm sweep with blades and frame and louvers. (Old unsv exhaust fans to deposited to MES to be kept in store) Please Enable Macros to View BoQ information |
| 153 | Supply and fixing exhaust fan, steel body AC single phase, 230 V of size 300 mm sweep with blades and frame and louvers. (Old unsv exhaust fans to deposited to MES to be kept in store) Please Enable Macros to View BoQ information |
