|
| 1 | P & L in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering -All work up to plinth level. (A) 1:4:8 ( 1 cement : 4 coarse sand: 8 graded stone aggregate 40mm nominal size.) (B/3.1.6) |
| 2 | (A) M-15 Grade N.Mix. 1:2:4 ( 1 cement : 2 coarse sand: 4 graded stone aggregate 20mm nominal size.) (B/3.1.2) |
| 3 | RR stone masonry for with hard stone in foundation and plinth in CSM above 30cm thick wall in CM 1:6 (1cement :6 Sand). (B/6.1.6) |
| 4 | Brick masonry with F.P.S. bricks of class designation 75 in foundation and plinth with bricks Cement mortar 1 : 6 (1 cement : 6 coarse sand) (B-5.1.2) |
| 5 | P & L in position specifed grade of cement concrete for all RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1: 3 (1cement : 3 coarse sand) and making good the joints & cost of plastizers (if required) excluding the cost of centering, shuttering and reinforcement. M20 grade Nominal Mix /Design Mix. (B-4.1) |
| 6 | S & F stone lintels / bed plates of approved quarry rough dressed in cement mortar 1:4 : Up to 15 cm thick. (B-6.18.1) |
| 7 | Half brick masonry in superstructure, above plinth level upto floor V level using bricks of designation 75. Cement mortar 1:6 (1cement: 6 coarse sand). (B-5.8.3) |
| 8 | Brick work with clay flyash F.P.S. brick (IS 13757- 1993 ) of class designation 75 in superstructure above plinth level upto floor five level in : Cement mortar 1 : 6 (1 cement : 6 coarse sand) (B-5.15.2) |
| 9 | P & F precast cement concrete coping 1:2:4 mix 50 mm thick copmlete as per specification : (B-3.8) |
| 10 | P & F steel glazed doors windows and ventilator shutters of standerd rollde steel section joints mitred and welded with steel lugs 13x3mm, 10 cm, long embeded in cement concrete block 15X10X10CM of 1:3:6 (1 cement : 3 coarse sand :6 graded stone aggregate 20mm nominal size) of with wooden plugs and screws of rawl plugs and screws with fixing clips or with bolts and nyts as required including providing and fixing of plain glass panes 4mm thick with cooper glazing clips and special metal sash putty of approved make of metal beading with screws complete including priming coat of approval steel primer, excluding the cost of metal beading and other fitting except necessary hinges of pivots steel handlwds peg stay etc. as required:(A) Window side hung /Ventilators top or centre hung (openable) (B-9.19.3) |
| 11 | Supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20×3mm with suitable screw at not exceeding 150 mm distance. (B-9.26) |
| 12 | Providing and fixing square bars or other flat welded to windows, ventilators etc. (B-9.27) |
| 13 | P & F T-iron frames for doors, windows & ventilators of mild steel Tee- section, joints mitred & welded with 15 X 3 mm lugs 10cm long embeded in CC blocks 15X10X10 cm of 1:3:6 (1cement :3 coarse sand: graded stone aggregate 20mm nominal size) or with woodenpluges & scews of plugs & scews or with fixing clips or with bolts & nuts as require including fixing of necessary butt hinges & screws & applying a priming coat of approved steel primer. (B-9.5) |
| 14 | S & F in walls machine cut and polished stone shelves,tands and in 1:3 with machine cut edges: (A) Kota stone minimum 30 mm thick (B-6.17.3) |
| 15 | Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 market using phenol formal dehysresin in glue both side with approved steel bildding complete as pr annexure A,30 mm thick commercial vernier both side. (B-8.13.2.1) |
| 16 | Extra for providing external lipping with 2nd class teak wood battens 6 mm minimum depth on all edges of shutters (over all area of door shutter to be measured) Over item no. 8.13. (B-8.14) |
| 17 | P & F M.S. Sheet 1mm thick single leaf door shutter in angle iron frame 35 x35x5 mm suitablly diagonally braced with 25 x 3 mm flat iron above & below lock rail of size 50x5 mm beading extra including all fittings, as per direction of Engg. Incharge but excluding cost of chowkhats: including two coat of anti-corrosive red oxide primer paint. (B-9.17) |
| 18 | Add Extra for Double leaf door shutter (B-9.17.1) |
| 19 | Applying priming coat:With ready mix pink or gray primer of approved brand and manufacture on wood work hard and soft wood. (B-12.45.1) |
| 20 | Painting with synthetic enamel paint of approved brand and manufacture to give and even shade : (A) Two or more coats on new work. (B-12.46.1) |
| 21 | One or more coats on old work. (B-12.46.2) |
| 22 | Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meter lead. (B-14.55) |
| 23 | Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches by sandla/loi. (only for colour changing ). (B/12.35.7) |
| 24 | Plaster on new surface on walls in cement sand mortar 1:6 including racking of joints etc. complete fine finished. (A) 25 mm thick(B-12.3.1) |
| 25 | (B) 20mm thick. (B-12.3.2) |
| 26 | (B) 12 mm thick. (B-12.3.3) |
| 27 | 6mm cement plaster to ceiling of mix 1:3 (1cement:3 fine sand). (B-12.5) |
| 28 | Providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete. (B-12.22.1). |
| 29 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding: (A) New work (two or more coats) over and including scrapping and priming coat with cement primer. (B-12.37.1) |
| 30 | Finishing walls with acrylic smooth exterior paint of required shade including all scaffolding. New work (two or more coats applied @ 1.67 ltr/10sqm over & including base coat of water proofing cement paint applied @ 2.20 Kg/10sqm). (B-12.42) |
| 31 | Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 m lead With cement mortar 1 :4 ( 1 cement : 4 coarse sand) (B-13.1) |
| 32 | Repair to stone masonary in cement sand mortar 1:6 with old and new stone. (B-13.12) |
| 33 | Spray painting in approved shade and approved quality with Duco paint of required colour to give even shade with two or more coats by compressor including sand papering, NC putty filler coat etc complete in all respect as per design given by Engineeer incharge on new work.(B-12.65) |
| 34 | Renewing glass panes, with putty and nails wherever necessary:Float glass panes of thickness 4 mm (B-13.4.1) |
| 35 | Repair of door, window shutters including cost of MATERIAL and LABOUR for change of damaged :(B/13.33) |
| 36 | (A) Panel by Shuttering Ply - 9mm thick (Commercial) (bi) |
| 37 | (B)Panel by Wire Gauge 14 mesh x 24 gauge(biii) |
| 38 | (C)Aldrop of mild Steel 12\\" long x12mm dia(ci) |
| 39 | (D) Stopper of Aluminium with Double Rubber Gutka (dii) |
| 40 | (E) Steel Hinges For Wooden Chowkhat 4\\" size(fiii) |
| 41 | (F)Steel Locking Bolt (hi) |
| 42 | (G) Steel Handle 6\\" size (iII) |
| 43 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, making of lines or groove etc complete but excluding the cost of nosing of steps etc. complete. 75mm thick with 20mm thick nominal size aggregate. .(B-11.3.2) |
| 44 | Labour charges for repair to door / window without using any material such as applying randha (finishing) tightening of bolts & screw etc.(B-13.24) |
| 45 | Repair of existing steel glazed doors, windows and ventilator, MS sheet door, garge doors, compound wall gates etc. by welding drilling complete include. Cost of welding rods and hire charge of welding meachine and TP etc complete (B-13.23) |
| 46 | Repair to damaged cement plaster of stone chajja with CM 1 : 3 of required thickness on top & bottom as per existing pattern and making patta etc complete up to three floor level as per direction of Engineer in charge including all necessary scoffolding etc (B-13.31) |
| 47 | P & F 1st qualityVitrified Porcelain Polished tiles on floor, skirting and steps etc.in different sizes (thickness to be specified by manufactuer) with water absortion less than 0.08% and conforming to IS 15622 of approved make in all colour and shade, laid with 20 mm thick CM 1 : 4 including grounting the join.size 600 mm X 600 mm(B-7.18.2) |
| 48 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting (height upto 10 m) , fixing in position and applying a priming coat of approved steel primer all complete: (B-9.2) |
| 49 | Providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to IS : 13753 & IS :15622 of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar).Extra for using size above 200x300mm in glazed tiles and for using 400mm x 400mm MAT finished tiles in place of 300mm x 300mm size. (B-7.12+7.15) |
| 50 | Providing and fixing 1st quality MAT finished ceremic tile size 300x300mm confirming to IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4).(B-7/7.13) |
| 51 | P&F Indian type white glazed vitreous china 1st quality W.C. orissa pan (IS : 2556 Mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor.Size 580x440 mm. (S-1.2.2) |
| 52 | P&F WVC wash basin (Ist quality IS: 2556 mark) of approved make with C.I. brackets duly painted, 1 No.15mm C.P. Pillar cock (IS: 8934 mark) & 32mm C.P. brass waste coupling of approved make, 25mm G.I. waste pipe complete including cutting and making good the walls, 580mm X 450mm. (S-1/1.36.4) |
| 53 | P & F Looking Mirrors with P.V.C. frame of approved make as per direction of Engineer-in-charge : Size 500x400mm (S-1.45.1) |
| 54 | P & F Towel Rail or Ring of approved quality/make: C.P. brass Towel Rail elbow type with concealed screws size 450mm (Heavy duty).(S-1.47.1) |
| 55 | P & F Chlorinated Polyvinyl Chloride (CPVC) pipe, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fitting i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement & testing of joints complete as per direction of Engineer in Charge. ( Internal work Exposed on wall). (A) 15mm nominal outer dia pipes. (S-2.37.1) |
| 56 | (B) 25mm nominal outer dia pipes. (S-2.37.3) |
| 57 | P & F Chlorinated Polyvinyl Chloride (CPVC) pipe, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings, this included jointing of pipes & fittings with one step CPVC solvent cement, trenching refilling & testing of joints complete as per direction of Engineer in Charge. ( External work). (A) 15mm nominal outer dia pipes. (S-2.39.1) |
| 58 | (B) 25mm nominal outer dia pipes. (S-2.39.3) |
| 59 | Making connection of GI distribution branch with GI main including all fitting : Upto 25mm dia. (S-2/2.3.1) |
| 60 | P&F bib cock (IS : 8931 mark), Superior quality of approved make.(A) CP Brass bib cock 15mm nominal bore. (S-2.7.3) |
| 61 | (B) CP Brass bib cock Long body, 15mm nominal bore weight not less than 690 gm. (S-2.7.5) |
| 62 | P&F ball cock (IS : 1703 mark) with rod& PVC ball complete: Brass wt. 400gm 15mm. (S-2.11.1) |
| 63 | P&F inlet connection (Angle velves) superior quility of approved make for washbasin Gyser etc. CP intel connection 15 mm Brass (IS: 8931 marked). (S-2/2.12.1) |
| 64 | P & F 15 mm. Dia Connection Pipe of approved quality/make :PVC pipe with C.P. Brass nuts upto length, 300mm. (S-2/2.13.1) |
| 65 | P & F Full way valve (IS : 778 Mark) or wheel valve of approved make. (A) Gun-metal 15mm nominal bore. (S/2.15.1) |
| 66 | (B) Gun-metal 25mm nominal bore. (S/2.15.3) |
| 67 | P&F PVC storage tank (IS: 12701 marked including the BIS license No.) of approved make with cover,25 mm dia IM long over flowing & 25 cm. Long wash out pipe with plug & socket, including making connection etc. Complete of approved deisgn : 500 liters capacity. (S-2/2.26.3) |
| 68 | Providing & Laying C.C. 1:3:6 (Stone Agreegate 20mm nominal size) all around PVC Pipe including 7.5 cm thick bed concerte [Width & Height = Dia of Pipe in CM+15CM] excluding cost of Pipe & Excavation of trenches etc. |
| 69 | (A)PVC pipe 110 mm dia(S/3.16.5.1) |
| 70 | (B)PVC pipe 160 mm dia(S/3.16.5.2) |
| 71 | P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.) approved quality /make including joining the pipe with solvent cement rubber ring and lubricant. |
| 72 | (A)110 mm dia (S/3.16.3) |
| 73 | (B )160 mm dia (S/3.16.4) |
| 74 | P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: |
| 75 | (A) Bend 87.5. 110mmdia(S/3.17.9/(II)) |
| 76 | (B) Bend 45. 110mmdia(S/3.17.8/(II)) |
| 77 | (C )Coupler (Soket) 110mmdia. (S/3.17.1/(II)) |
| 78 | (D)Pipe clip.110mm dia.(S/3.17.15/(ii)) |
| 79 | (E)VENT Cowel .110mm dia.(S/3.17.12/(ii)) |
| 80 | (F )PLAIN TEE 110mmdia. (S/3.17.3/(ii)) |
| 81 | Construction of chamber in all type of soil with 300 mm thick masonry in CM 1:6 m,10 cm thick C.C. 1:5:10 in foundation, 20mm thick insider plaster in Cm 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring , earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. :Inside size 300 X 300 mm depth upto 0.5 M Cement cover with frame. (S/3.21.1) |
| 82 | P & F Flush Cock / Flush Valve (IS : 9758 Mark) for WC of approved quality make : 20mm nominal bore. (S-2.14.2) |
| 83 | P & F Soap Dish or Tray of approved quality/make C.P. brass (S-1.52.1) |
| 84 | P & F sand cast Floor Trap (Nahni) of (IS : 1729 mark) of approved quality / make with socket down or hinged grating including good the floor.Size 100x100mm. (S-3.12.1) |
| 85 | Construction of manhole in all type of soil inner size 90 X 60 Cm. 300 mm thick masonry in CM 1:6, 10 Cm. thick cement concrete 1:5:10 in foundation, 20 mm thick inside plaster in CM 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring, making channels, 80mm thick stone slab covering with 40mm thick M-15 grade C.C. flooring, Cement cover with frame of 450mm dia, earthwork etc. complete as per design including disposal of surplus earth within 50 mtr. lead..Depth up to 0.5 M(S-3.19.1) |
| 86 | Construction of septic Tank in all types of soil with 40 Cm .thick masonry in CM 1:6, 15 Cm thick C.C bed of 1:5:10, M- 15 grade C.C floor & RCC slab covering with M15 grade c.c. floor, 50 mm thick stone slab partition walls, 20 mm thick plaster in CM 1:6 finished with neat floating cement, 4 Nos stone foot rests of approved design ,two No. 450 mm dia each Ferro cement cover with frame, earth work etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 mtr:-. size 200×100×130 cm. (for 10 users.) with 115 mm thick RCC (M-20) slab with Tor steel reinforcement 8mm ϕ @15 cm c/c bothways including shuttering complete in all respect. (S-3.27.1) |
| 87 | P & F Pilllar Cocks (IS :8931 : 1993 Mark) of superior quality and approved make:C.P. Pillar cock, 15 mm dia nominal bore.(S/2.6.1) |
| 88 | P& F waste Pipe with all fitting:P.V.C with PVC nut 32 mm.(S/1.43.2) |
| 89 | P & F Grating of approved quality/make:Stainless Steel Sheet size 125mm dia.(S/1.48.1) |
| 90 | Labour Charges for Removing & Refixing the water Storage Tank of all sizes and including all Necessary fitting complete in all respect as per approved sample and direction of engineer in charge..(S/2.41) |
| 91 | Providing and fixing superior quality PVC Tank Cover complete as per approved by Engineer In Charge. |
| 92 | (A) 300 Lt. capacity (S/2.44.1) |
| 93 | (B) Above 500 Lt. Capacity (S/2.44.3) |
| 94 | Labour charges for removing W.C. pan (any type) of all sizes with care including all necessary fittings P or S trap..(S/1.9) |
| 95 | Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & it's ISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thick Hot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure 'A' attached with this BSR (A) Short point (upto 3 mtr) (E1.1) |
| 96 | (B) Medium point (up to 6 mtr) (E1.2) |
| 97 | (C) Long point (uo to 10mtr) (E1.3) |
| 98 | Wiring of 3/5 pin 6 amp. Light plug point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) PVC conduit & it's ISI marked (IS:3419-1988)accessories, Hot Dipped Galvanized Modular box of 1.2 mm thick with earth terminal, 10 A modular switch, 3/5 pin 6 A modular socket, Modular face plate with grid plate, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure 'A' attached with this BSR.On Board(E1.3.1) |
| 99 | Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR (A) 2×2.5 sqmm+1x1.5 sq.mm (E4.1.7) |
| 100 | (B) 2×4.0 sqmm+ 1x2.5 sq.mm ( E4.1.14) |
| 101 | Providing and fixing of power plug point with non modular accessories as per PWD specification for electrical Works with Galvanized box of 1.2 mm thick with earth terminal with suitable size phenolic laminated sheet (IS : 2036 - 1995) cover including cost of 16 amp. Switch (IS :3854) and 3/6 pin 16 amp. socket outlet making connection , testing , etc. as required. . For specification of Wiring accessories refer Chapter E - 07 related item & For additional technical parameters of product / work refer Annexure 'A' attached with this BSR(E7.36) |
| 102 | Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load and site requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted in existing distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above rating including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached with this BSRSingle pole MCB (With B/C curve tripping Characteristics) 6 A to 32 A rating (E6.1.1.2) |
| 103 | Providing & Fixing of 240/415 V isolator ISI marked IS:13947-III/conforming to IEC 60947-3, suitable for AC22A utilization category, 4KV impulse withstand voltage, true contact indication, Red colour dolly / lever shall have single mould covering over all poles for operation , two position din rail mounting, minimum phase termination capacity of 35sq.mm. IP 20 contact protection and fitted in existing distribution board / sheet including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge.For additional technical parameters of product / work refer Annexure 'A' attached with this BSR Double pole isolator30 A / 40 A rating(E6.2.1.1) |
| 104 | Providing & Fixing of Recessed/surface mounting heavy duty Enclosure made out from Galvanized steel / CRCA sheet not less then 1.2 mm thick conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3. powder painted complete with din rail making internal DB terminations with copper lugs, detachable gland plate, including making connections, testing etc. as required.For additional technical parameters of product / work refer Annexure 'A' attached with this BSRSuitable for Six / Eight module for MCB/ RCCB (E6.9.2) |
| 105 | Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from Powder coated Extruded aluminium housing with in built driver , System lumen efficacy ≥ 110 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , Maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR .1170mm(+/-10%) LED batten with min. lumen output 2200 lm(E17.1.1) |
| 106 | Providing & Fixing of energy efficient /energy saving IP 20 LED direct retrofit Bulb in existing holder or fixture as required with system lumen efficacy ≥100 lm/Watt output ,pf 0.95 , CRI >70, minimum life time of minimum 25000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) certificate / Report from OEM shall be submitted. All as per pre approved by engineer in charge . for additional technical parameters of product/ work, refer Annexure \\"A\\" attacheded with this BSR.9 Watt(E17.9.3) |
| 107 | Providing & Fixing of IK08, IP 66 protected LED Street Light Luminaire on existing bracket/pole. Fixture made of powder coated single piece pressure die cast aluminum material with heat dissipation fins on housing with UV stabilized PC (UV stablization report submitted for UV cover ) /Toughened Glass cover and secondary lens on each LED & should be SMD type of 3 to 5 watt each . The System efficacy >=125 lm/ wt and potted driver & has a unique BIS R number with Input Voltage AC 120 to 270 V AC with High voltage Cutoff @>=300 V AC and Auto resetting Safety , Power Factor >0.95 driver Efficiency >85% ,THD(I) <10% Humidity 10% to 90% RH Working Temp -5C to 45C . driver current <750mA. The luminaire shall be BIS certified and Trade mark certified. Life Expectancy Equal or more than 50000 burning hrs with Minimum 70% lumen maintened , CRI >70 and CCT 5700K +355K. Surge protection shall be min ≥ 4 KV internal and min 10 KV external inside driver compartment. driver should be Phase to phase protection of 440 V for 4 Hrs. Manufactures Word Mark/Name Engraved/Embossing on die cast housing to allow traceability/authenticity. Fixture shall be AS PER IS 10322 Complianced.OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . (A)LED Street Light fixture with Minimum lumen output 3700 lm (E-18.12.2) |
| 108 | Providing & Fixing of modular type 120 W Step Fan regulator duly ISI marked (IS 11037:1984 ) with CM/L no. printed made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating , including all as per pre approved by Engineer in charge,making connections, testing etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR5 step fan regulator 2 Module 360 dgree rotating(E-7.29.1) |
| 109 | Supply and installation of Multi Rib Proofing/cladding Sheet Manufacture out of 0.50mm TCT (Total Coated Thickness) high tensile Zinc aluminum alloy coated galvalume steel (as per 150gsm zinc aluminum coated 550Mpa tuekd strength) confirming to IS: 1397/astm A-792 sheet to have wide pens 30mm high NB at 250 centre and centre width of 1020mm sheets be casted with regular modified polyster system on a continuous with line on centre for face and with a polyster coating respectively sheet shall have proportionality with siphoned plate made to prevent leakage sheet shall be fixed by more of sell drilling lift tapping hot dip zinc coated hox head fasterner of size 12x14x55mm long. The sheet shall be supplied in cost one length and for a minimum up to 12mts with all scaffolding.(B-17.1) |
| 110 | Providing & applying one coat of UV resistant polymer cement based waterproofing slurry coating of approved make and quality on concrete or plastered surface as per specifications including preparation of surface by cleaning brushing and dust removing, filling of cracks and making the surface leak proof by mixing one part of chemical with 2 parts of cement and 2 parts of water (covering area 1.86 Sq.M/Kg of chemical) including cost of cement, labour, tools & plant, scaffolding if necessary etc., complete as directed by Engineer in Charge.Note: Undulations/cracks found on the surface should be rectified with Cement Motor before application and the same will be paid under relavent items. (B-15.3) |
| 111 | Providing & fixing calcium silicate perforated ceiling tiles of size 595 x 595 mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanised steel sections ( galvanized @ 170 gsm/sqm.) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38mm made from 0.30mm thick (minimum) sheet spaced at 1200mm center to center and cross “T” of size 24x25mm made of 0.30mm thick (minimum) sheet, 1200mm long spaced between main “T” at 600mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600mm and size 24x25mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 21x21x0.30 mm and laying false ceiling tiles of approved texture in the grid including, wherever, required, cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats fixed to ceiling with 6 mm dia and 50mm long dash fasteners, 4mm GI adjustable rods with galvanised level clips spaced at 1200mm center to center along main T, bottom exposed width of 24mm of all T-sections shall be pre-painted with polyester paint, all complete at all heights as per specifications drawings and as directed by Engineer-in-Charge of thickness of tiles as mentioned below:6 MM THICK(B-10.33.1) |
| 112 | P&F of cooler water tank approx size 1.0x0.85x0.175 m in existing cooler dismantling of existing of water tank carefully & fixing of new tank at Bundi City offices by suitable means including labour T&P transportation of same tank with 20 SWG sheet for tank complete as per direction of Engineer in charge. |
| 113 | S&F set of three side panel for a complete cooler including all labour T&P material etc complete as per direction of Engineer in charge panels size approx 1.0x0.86 m . |
| 114 | P&F of cooler top appox size 0.65x0.65x0.05 m in existing cooler dismantling of existing cooler top carefully, fixing of new cooler top at Bundi City offices by suitable means including labour, T&P, spray panting including removing & refixing of cooler labour charge transportation with 20 SWG sheet labour charge transportation with 20 SWG sheet for top complete as per direction of engineer in charge. |
| 115 | Providing & fixing Retro reflectorised sign board on single side as per IRC:67 made of high intensity grade sheeting and approved drawing including required name on sign board and specification made of 2mm thick aluminium sheet of size 1200x900mm stiffened by flat 40x5mm all around the plate and duly framed with 32 mm dia medium MS black pipe fixed on frame of 50 mm dia medium pipe (vertical post 3600 mm,3000mm above ground level with angle iron hold fast 35x35x5mm with horizontal member 1500mm to be jointed with flat 40x6mm and post embedded in cement concrete blocks M-15 grade of 450x450x750mm size below ground level as directed by Engineer all MS will be stove enameled and border on sheet with ready mix synthetic enamel paint of superior quality in required shed and colour etc. complete in all respect all support framed post and steel tubes will be painted with primer and two coats of enameled paint as per specifications and direction of Engineer incharge. Over all size 1500 x 1200mm. |
| 116 | Providing and fixing steel almirah shutters for almirahs & wardrobes in different sizes as per site requirement made with 20 Gauge CNC sheet and having three way loocking devices with six brass levers lock and godrej type handles and 10mm dia locking rod,painted with three coats of superior quality danedar synthetic enmeled paint over approved quality primer coat etc.Complete in all respect including fixing at site or with help of suitable holdfast or nuts & bolts etc. (measurement shall made for front visible position/size of shutter including frame. Please Enable Macros to View BoQ information |
