|
| 1 | Demolishing cement concrete manually / by mechanical means including disposal of material with all lifts and upto 50 m lead etc. complete as perdirection of the Engineer- in-charge:i) Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 2 | Demolishing reinforced cement concrete manually / by mechanical means including stacking of steel bars properly and disposal of unserviceable material with all lifts and upto 50 m lead etc. complete as per direction of the Engineer- in-charge. |
| 3 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. Complete and stacking within 50 metres lead.i) Of area 3 sqm and below |
| 4 | Dismantling old plaster or pointing, raking out joints, cleaning and preparing the surface for re-plastering or re-pointing including disposal of rubbish to the dumping ground with all leads and lifts etc.complete as per direction of the Engineer- in-charge. |
| 5 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.i) For thickness of tiles 10 mm to 25 mm |
| 6 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.1) -All kinds of soila) By manual means |
| 7 | Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete. |
| 8 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering •-All work upto plinth level:a) 1:4:8 ( 1 Cement 4 fine sand: 8 graded well burnt brick aggregate 40 mm nominal size) |
| 9 | Grading roof for water proofing treatment complete as required as per direction of the Engineer-in-charge with:i) Cement concrete 1:2:4 (1 cement: 2 fine sand: 4 graded stone aggregate 20 mm nominal size) |
| 10 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 fine sand: 6 graded well burnt brick aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth. |
| 11 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement-a) All work upto plinth level:i) 1:1 ½:3 (1 Cement: 1 ½ fine sand 3 graded stone aggregate 20 mm nominal size) |
| 12 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centering, shuttering, finishing and reinforcement-i) 1:1½:3 ( 1 Cement: l½ fine sand 3 graded stone aggregate 20 mm nominal size) |
| 13 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.i) Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 14 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.i)Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 15 | Centering shuttering including struttings, propping etc. and removal of form work for:i) Suspended floors, roofs, landings, balconies and access platform with timber planks |
| 16 | First class brick work in foundation and plinth including cost of all materials as required complete:-i) In cement mortar 1:4 ( 1 cement: 4 fine sand). |
| 17 | Half brick masonry work with first class bricks in foundation and plinth including cost of all materials as required complete:- I) In cement mortar 1:4 ( 1 cement: 4 fine sand). |
| 18 | Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete:-i) In cement mortar 1:4 ( 1 cement: 4 fine sand). |
| 19 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position :i) Karai wood |
| 20 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.a) 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. |
| 21 | Providing and fixing factory made door frame (single rebate) made of solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 60mm width & 30mm thickness and shall be fixed to wall as per instructions of Engineer-In-Charge using 100x8 sheet metal CSK screws. |
| 22 | Providing and fixing 28 mm thick door shutter made of solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 71mm width & 28mm thick as vertical & horizontal styles. Joints are made using solvent adhesive and GI 'C sections (39mm x 19mm x 0.6mm thick) Or M S pipe (40mm x 20mm ) stiffener frame insert & telescopic polymeric 'L' corners .The panel shall be filled with 3mm thick high - pressure compact laminate as per manufacturer's specifications and directions of the Engineer-in-charge, cover moulding shall be provided for covering fixing screws and elegant look.( for W.C. bathroom door shutter). |
| 23 | Providing and fixing glazing of approved quality in aluminium doors, windows, ventilator, shutters and partition etc. with EPDM rubber / neoprene gasket etc. complete as per architectural drawing and the direction of Engineer-in-charge (Cost of snap beading shall be paid in basic item):•i) With float glass panes of 4.0 mm thickness ( weight not less than 10.0 kg / sqm ) |
| 24 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete.i) Fixed to openings /wooden frames with rawl plugs screws etc. |
| 25 | Providing 40 x 5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30 x 10 x 15 cm 1:3:6 mix (1 cement: 3 fine sand : 6 graded stone aggregate 20mm nominal size) |
| 26 | Providing and fixing aluminium tower bolts ISi marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : |
| 27 | Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete:i. 125 mm |
| 28 | Providing and fixing aluminium sliding door bolts ISi marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete:i.300xl6 mm |
| 29 | Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with:i. 4.0 mm thick glass panes |
| 30 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawing and the direction of Engineer-in-charge. (Glazing and paneling and dash fasteners to be paid for separately) :•i) Size of tile 600mmx600 mm |
| 31 | For fixed portion of approved quality:•i) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). |
| 32 | For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing fittings wherever required including the cost of EPDM rubber / neoprene gasket required ( Fittings shall be paid for separately ):•i) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). |
| 33 | 12 mm cement plaster of mixi. Cement mortar 1:4 (1 cement : 4 find sand) |
| 34 | 15 mm cement plaster on the rough side of single or half brick wall of mix :i) Cement mortar 1:4 (1 cement : 4 fine sand) |
| 35 | 6 mm cement plaster mixi) Cement mortar 1:3 (1 cement : 3 find sand) |
| 36 | Neat cement punning |
| 37 | Distempering with 1st quality washable acrylic distemper of approved brand and manufacture and of required shade on old work ( one or more coats ), to give an even shade as required complete as per direction of the Engineer in charge |
| 38 | Distempering with 1st quality acrylic distemper (ready mixed) having voe content less than 50 grams/ litre, of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer]:i) New work ( two or more coats) over and including water thinnable priming coat with cement primer. |
| 39 | Finishing walls with acrylic smooth exterior paint of required shade of approved brand and manufacture on old work ( one or more coats ) including preparation of surface as required complete as per direction of the Engineer in charge. |
| 40 | Finishing walls with acrylic smooth exterior paint of required shade of approved brand and manufacture [Payment shall be made after submission of Test Certificate issued by the Manufacturer]:i) New work (two or more coats applied @ 1.67 litre/10 sqm over and including priming coat of exterior primer applied @2.20 kg/10 sqm) |
| 41 | Applying priming coat [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : |
| 42 | With ready mixed Pink or Grey primer of approved brand and manufacture on wood work ( hard & soft wood ). |
| 43 | With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works |
| 44 | Painting with synthetic enamel paint (one or more coats) of required colour of approved brand and manufacture on old work to give an even shade including preparation of surface as required complete as per direction of the Engineer in charge. |
| 45 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer]:i) Two or more coats on new work |
| 46 | Cement concrete flooring 1:2:4 (1 cement : 2 fine sand: 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. all completeetc as per direction of Engineer-in-charge. i) 40 mm thick with 20 mm nominal size stone aggregate |
| 47 | Providing and laying 1st class quality ceramic floor tiles in different sizes (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622•2017 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid over 20 mm thick cement mortar 1:4 (1 cement : 4 fine sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc. all complete as per direction of the Engineer in-charge.i) Mat Finish Tiles/ Anti-skid Tiles/ Glossy Tiles 300 mm x 300 mm in all shades and designs |
| 48 | Providing and fixing 1st class quality ceramic glazed wall tiles conforming to IS : 15622 - 2017 (thickness to be specified by the manufacturer) of approved make in all colours, shades of any size as approved by Engineer-in• charge in skirting, risers of steps and dados, laid over 12 mm thick bed of cement mortar I : 3 (1 cement : 3 fine sand) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade etc. all complete as per direction of the Engineer in-charge.a) 450 mm X 300 mm in all shades and design |
| 49 | Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 50 | Providing and fixing 600xl20x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 51 | Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colours weighing not less than 105 gms |
| 52 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour.i) 600mm long towel rail with total length of 645mm, width 78mm and effective height of 88mm, weighing not less than l 90gms. |
| 53 | Providing and fixing white vitreous china water closet squatting pan (Indian type)i) Orissa pattern W.C. pan of size 580x440 mm |
| 54 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.i) 10 litre capacity-White |
| 55 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :i) White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps |
| 56 | Providing and fixing kitchen sink including making all connections excluding cost of fittingsi) White glazed fire clay sink of size 600x450x250mm |
| 57 | Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required:a) Kitchen sink without drain boardi) 610x460 mm bowl depth 200 mm |
| 58 | Providing and fixing 3 layer PP-R (Poly propyleneRandom copolymer) pipes SOR 7.4 U V stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply including all PP - R plain & brass threaded polypropylene random fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall |
| 59 | PN-16 Pipe, 16 mm OD |
| 60 | PN-16 Pipe, 20 mm OD |
| 61 | PN-16 Pipe, 25 mm OD |
| 62 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801, U V stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply including all PP - R plain & brass threaded polypropylene random fittings including trenching,refilling & testing of joints complete as perdirection of Engineer in Charge.External work |
| 63 | PN-16 Pipe, 16 mm OD (SDR-7.4) |
| 64 | PN-16 Pipe, 25 mm OD (SDR-7.4) |
| 65 | PN-16 Pipe, 40 mm OD (SDR-7.4) |
| 66 | Providing and fixing brass bib cock of approved quality:i) 15 mm nominal bore |
| 67 | Providing and fixing brass stop cock of approved quality:i) 20 mm nominal bore |
| 68 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISi : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 69 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with 1st class bricks in cement mortar 1 :4 (1 cement : 4 fine sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) R.C.C. top slab with 1:2:4 mix (1 cement :2 fine sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement: 5 fine sand 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 fine sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design :i) Inside dimensions 455x610 mm and 45 cm deep for single pipe line : |
| 70 | Constructing soak pit 1.20 x 1.20 x 1.20 m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design. |
| 71 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sqm and under including cutting the patch in proper shape and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground with all leads and lifts including finishing even and smooth and curing complete as per direction of the Engineer in charge:- i) With cement mortar 1:4 (1 cement : 4 fine sand ). |
| 72 | Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge. |
| 73 | Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete Please Enable Macros to View BoQ information |
