Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Surface dressing not exceeding 15cm deep and getting out in soft and loose soil, complete all as specified and directed |
| 2 | Excavation in trenches nexc 1.5m wide and not exceeding 1.5m in depth for foundation, not exceeding 10sqm on plan and not exceeding 1.5m in depth and getting out in soft and loose soil, complete all as specified and directed. |
| 3 | Removing excavated soil exceeding 250 m but not exceeding 500m distance and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and directed. |
| 4 | M&L for PCC 1:4:8 type D-2, using 40mm graded stone aggregate, as in foundation filing, sub base of floor complete all as specified and as directed |
| 5 | M&L for RCC M-25 (design mix) using 20 mm graded stone aggregate as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed . |
| 6 | M&L for RCC M-25 (design mix) using 20 mm graded stone aggregate as in Columns, pillars, piers, posts and struts complete all as specified and as directed |
| 7 | M&L for RCC M-25 (design mix) using 20 mm graded stone aggregate as in lintal band at any height complete all as specified and as directed |
| 8 | M&L for RCC M-25 (design mix) using 20 mm graded stone aggregate as in slabs supported on walls, roof beams etc and the like, complete all as specified and directed. |
| 9 | M&L for RCC M-25 (design mix) using 20 mm graded stone aggregate as in beams, complete all as specified and directed. |
| 10 | Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed |
| 11 | Formwork to sides of pillars, posts, struts, piers, columns and stanchions with rough finished surface complete all as specified and as directed |
| 12 | Form work to sides and soffit of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc rough finished complete all as specified and as directed |
| 13 | Form work to soffits of suspended slabs such as roof slab etc. not exceeding 200mm thick for fair finished surfaces of concrete complete all as specified and directed. |
| 14 | Form work to chullah hood, chajjas, troughs and similar items including edges complete all as specified and directed. |
| 15 | M&L for Mild steel bars (TMT) 5mm dia and over upto and including 10mm dia in strriups,spaces,nibs and binders complete all as specified and directed. |
| 16 | M&L with subclass 'B' bricks , straight or curved on plan exc 6 m mean radius, built in cement mortar 1:6 complete all as specified and directed |
| 17 | M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work finished even and fair without using extra cement complete all as specified and as directed |
| 18 | Preparation of newly plastered surface of ceiling and applying two coats of white wash complete all as specified and directed |
| 19 | Preparation of newly plaster surface of wall and applying two coats of cement base paint including one coat of primer complete all as specified and directed. |
| 20 | M&L for hardcore of gauge not exceeding 63 mm,of broken stone deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed. |
| 21 | M&L for 150mm thick PCC ( 1:4:8) type D-2 using 40mm graded stone aggregate as in sub-base complete all as specified and directed |
| 22 | M&L for 50mm thick PCC(1:2:4) type B2 (40mm graded stone aggregate) finishing surface even and smooth using extra cement complete all as specified and directed. |
| 23 | M&L for 75 mm thick cement concrete 1:3:6 type C-2 using 20 mm graded stone aggregate in plinth protection finished even and smooth without using extra cement including necessary formwork and cutting of joints complete all as specified and directed. |
| 24 | M&L for sand cushning under floor or in foundations including watering and consolidation etc. or for cable protection complete all as specified and directed |
| 25 | M&L for machine cut kota stone slab flooring 14-16 mm thick over 20mm thick CM (1:4) screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. |
| 26 | M&L for machine cut kota stone slab 14-16 mm thick in riser of steps, skirting dado and pillar laid over 15mm thick CM (1:4) screed bed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. |
| 27 | M&L for preparing cement concrete surface, providing 10 mm thick modified plaster in CM 1:4, cement mixed with polymer in ratio of 1:10 (1 part of polymer and 10 parts of cement), applying primer coat of epoxy primer with resin and hardener with water dilution as per manufactirer instructions, applying two coats of polyurethane liquid membrane each coat not less than 500 micron thick UV stable having SRI value equal or greater than 105 with consumption of 0.61 Kg/ Sqm (each coat), 2 nd coat should be applied once 1 st coat is fully dried. The item includes applying epoxy primer @ 0.15Kg/Sqm and a geotextile of 40 GSM to be applied over first coat while first coat is still wet, complete as per manufacturer's instructions complete all as specified and directedNote :-1. Make of material is Asian paints or equivalent as approved. 2. Work to be executed by company Professional and company guarrantee to be ensured by contractor for 7 year time period . |
| 28 | S&F Steel rolling shutters thickness of lath 1.25mm without ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated,complete: push pull or manual type complete all as speciied and directed. |
| 29 | S&F factory made box type steel ventilator with glazing bars dovetailed or welded and fixed with grills with one coat of zinc chromate primer complete all as specified and directed. |
| 30 | M&L for 4.8 mm thick plain sheet glass ,ordinary quality and glazing with oil putty in square n exc 0.5sq. m in each pane complete all as specidfied and as directed. |
| 31 | Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm, Made of G.I. wire of dia. 4 mm, PVC coated to achieve outer dia not less than 5 mm in required colour and shade including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. |
| 32 | S&F rolled mild steel Fe-290 (Grade E-165) angle or tee section as in post, cut to length and bend to shape as directed, fixed independetly without connecting plate etc, including provision of 05 to 06 Nos gaps/cuts/holes in each post for providing/ laying barbed wire and painting with two coats of synthetic enamel paint over a coat of zinc primer complete all as specified and as directed. Note :- Supply and fix barbed wire shall be measured and paid separately. |
| 33 | Excavating in post holes (or similar holes) each not exceeding 0.5 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and directed |
| 34 | Taking down cement plaster on brick or stone walls or ceiling etc including racking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed. |
| 35 | M&L for rendering 15 mm thick on fair faces of brick work in CM in 1:4 finished even and fair and mixing with water proofing liquid as per manufacturer instruction (but excluding the cost of water proofing liquid) external surface, complete all as specified and directed. |
| 36 | Supply only Integral crystalline water proofing compound of approved make, complete all as specified and directed. |
| 37 | M&L for rendering 5 mm thick in CM 1:3 on concrete plaster surface in ceiling complete all as specified and directed. |
| 38 | M&L for rendering 10 mm thick in CM (1:6) on Brick/ Conc surface finished even and fair on internal surfaces of wall, complete all as specified and directed. |
| 39 | M&L for complete removal of existing treatment on interior and exterior surface of wall/roof projections including facia, cornices etc by scrapping with wire brush/sanding paper/Metal Patti. Removing nails of appropriate grit to make surface clean, free from dust, loose paint etc by skilled labour, complete all as specified and directed. |
| 40 | Material and labour for two coats of water based premium acrylic smooth exterior emulsion of approved coulur with silicon addictive & color stay technology excellent dirt pick up resistance with low VOC less than 50 gram/ltr as per the LEEDS specification anti algal propertiess in two coats @ 1.79 ltrs (undiluted)/10sq mtrs diluted with water as per manufacturer instruction, complete all as specified and directed. |
| 41 | Material and labour for 1mm thick wall care putty with one coat of acrylic water based interior / exterior grade primer @0.9 ltrs (undiluted)/10sq mtrs diluted with water 1:1 ratio. Allow 6-8 hrs to dry the surface for painting of subsequent coats, complete all as specified and directed. |
| 42 | M&L for preparation of new or old plastered surface and applying two coats of oil bound distemper on walls and ceiling incl , complete all as specified and directed. |
| 43 | Chipping of unsound/weak concrete material of 50 mm average thickness from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts complete all as specified and directed by Engineer-in-ChargeNote :Where the items executed upto 12 mtr height, necessary scaffolding, props, jacks, shuttering and ladder shall be provided by the contractor in his own arrangement and the same is included in unit rates quoted. |
| 44 | M&L for Cleaning of reinforcement from rust from the reinforcing bars upto 12mm dia to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge.Note :Where the items executed upto 12 mtr height, necessary scaf folding, props, jacks, shuttering and ladder shall be provided by the contractor in his own arrangement and the same is included in unit rates quoted. |
| 45 | Providing, mixing and applying SBR polymer modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) 50mm thickness in 03 layers as per specification and directions of Engineer-in-charge. Note :Where the items executed upto 12 mtr height, necessary scaffolding, props, jacks, shuttering and ladder shall be provided by the contractor in his own arrangement and the same is included in unit rates quoted. |
| 46 | M&L for surface prepartion and providing & applying weld-mesh of size 75x75x3mm to be wrapped on the exposed surface of rib of beam & on the slab bottom and tack welding to the exposed reinforcement at close interval and gunite with cement mortar 1:3 mixed with admixture SIKA Plasto creat plus or equivalent make in Fosroc/Thermax as per manufacturer instruction and as approved by GE around rib of beam or roof slabs of thickness nexc 40mm to be applied under an operating pressure. The gunited surface to be cured properly for a min of 7days all in complete as per the technical specifications and manufacturers instruction and directed by Engr-in-charge.Note- Cost of Scaffolding is included in the item |
| 47 | Taking down Chowkats or frames not exceeding 1.5 Sqm each (Without taking off shutters from the frame).(Ventilator and Window). |
| 48 | Taking down Chowkats or frames exceeding 1.5 Sqm but not exceeding 4.00 Sqm each (Without taking off shutters from the frame).(Doors and Window). |
| 49 | S&F Pressed steel frame 125 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges lock strike plate etc complete all as specified and fixed, including preparation of new primed surface and applying two coats of synthetic enamel paint over steel surface complete all as specified and directed |
| 50 | M & L for PCC (1 2 4) type B-1 using 20mm for filling in door frames complete all as specified and directed |
| 51 | S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed.NOTE :(i) The WPC shall comprising of virgin PVC polymer of K value 58-60 Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms). (ii) The frame shall fabricated with mitre joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws.(iii) The WPC shall have minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant.(iv) The cost of M.S. hold fast/ lugs or SS dash fasteners shall deemed included in quoted unit rate. Each frame shall be fixed with min 06x holdfasts/ faster's. |
| 52 | S&F 30 mm Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size withnecessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed by Engineer-In-Charge. Note: stainless steel butt hinges and necessary S S screws shall be paid separately. |
| 53 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moistureproof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of requiredsize with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed by Engineer-in- Charge. Note: stainless steel butt hinges and necessary S.S screws shall be paid separately. |
| 54 | S&F 30mm thick plain WPC factory made glazed Skeleton door shutters (conforming as per IS-4020) with density not less than 600 Kg/cum. Manufactured by an ISO : 9001-2015 certified company. The door to be panelled with SS mosquito mesh and XTN aluminium mesh for additional strength and safety purpose. Door should be fixed with SS hinges and SS screws. Door should be water proof, termite proof, fire retardant and having screw holding capacity complete all as per manufacturers specification & drawings complete all as specified and directed by Engr-in-charge.Note- Stainless steel wire mesh shall be measured and paid separately. |
| 55 | S&F Powder coated aluminium frame for Doors, windows, ventilators with one or more reabtes including joining cleat for fixing etc, complete all as specified and directed (Minium Thickness of powder coating is 50 micron). |
| 56 | S&F powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded builtup standard tubular sections/appropriate Z sections and other sections approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size including necessary filling up the gaps at junctions, i.e. at Top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/panelling, CP brass/stainless screws all complete as per architectural drawings and the directions of Engineer-in-charge. |
| 57 | Providing and fixing factory made UPVC white colour fixed window made of extruded profiles with wall thickness of 2.3mm(+0.2mm). Window profile with hollow section with multi chamber. Frame (60mm x 58mm). T profile (Onevertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware, EPDM gasket.1.2 +0.2mm thick, galvanized steel Frame (28mm x 21.5mm), T profile (27mm x 17 mm) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners- 5mm thick glazing with selected quality glass complete all as specified and directed.(Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories Net opening will be measured for payment purpose.) |
| 58 | Supply and fixing factory made UPVC white colour Two track four panels sliding glazed door made of (big series) frame 67x 50 mm & sash 46 x 82 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. comprising of uPVC multi-chambered frame, with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension uPVC extruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required), stainless steel (SS 304 grade) body with adjustable multi nylon rollers, G.l fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) |
| 59 | Contd/...Note: UPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 60 | Providing and fixing factory made UPVC white colour casement (openable) Door made of extruded profile with wall thickness of 2.3mm (+ 0.2mm). Window profile with hollow section with multichamber, frame (60mm x 58mm), sash (60mm x 78mm). T profile (one vertical length in between two shutter) (60mm x 74mm). Glazing beads (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2 + 0.2mm thick galvanised steel frame (28mm x 21.5mm) , sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fastener. Hardware (Casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary striker. Cylinder. Door transmission gear made of mild steel with multipoint locking system with strikes. 3D hinges of zinc alloyed (white powder coated) (5mm thick glazing with selected quality glass) complete all as specified and directed.Note- The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories.Net opening will be measured for payment purpose. |
| 61 | S & F Stainless steel wire mesh, 0.56mm nominal dia of wire and average width of aperture 1.00 mm and fixed with tinned tacks, or SS wire staples complete all as specified and directed. |
| 62 | M&L toughened plain/ Frosted glass of 8 mm thickness of any description icl necessary fittings to be fixed on SS Railing, partitions,doors and other work including cutting to shape, drilling holes as required complete all as specified and directed. |
| 63 | S&F 5.5 mm thick plain sheet glass as in,shutters with and including rubber gasket and natural colour anodized 15 micron snap on aluminium beading/glazing, clips etc complete all as specified and directed. |
| 64 | S&F 5.5 mm thick Frosted sheet glass as in shutters with and including rubber gasket and natural colour anodized 15 micron snap on aluminium beading/glazing, clips etc complete all as specified and directed. |
| 65 | S&F door sealing guard from insects, reptiles etc, complete all as specified and directed. |
| 66 | Providing and applying approved quality weatherproof silicone sealant around the perimeter of UPVC window frames (internal and external sides) to seal the gap between frame and masonry/plaster surface, including surface preparation, masking and cleaning, complete in all respects as directed by Engineer-in-Charge. |
| 67 | S & F 150mm SS handles, Complete all as specified and directed. |
| 68 | S & F 200mm SS barrel tower bolts fixed as specified and directed. |
| 69 | S & F 300 mm SS sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet fixed as specified and directed. |
| 70 | S & F 100 mm long SS butt hinges, complete all as specified and directed |
| 71 | S & F 300 mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed |
| 72 | S & F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor Door Stopper 140 mm complete all as specified and directed |
| 73 | Dismantling wrought Iron or mild steel work of any description not other wise described complete all as specified and directed. |
| 74 | S & F framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. including painting with zinc primer and two coats of synthetic enamel paint complete all as specified and directed |
| 75 | S&F framed work as in doors or gates of angle or other section such as tee, angle,channel, MS solid rod or flat section of Fe 290 (Gde-E-165), complete drilled for fixing, fastening and hanging, including one coat of red oxide primer and two coat of synthetic enamel paint, complete all as specified and directed. |
| 76 | S&F in repair fancy type drapery rod 20 mm dia stainless steel incl end brackets, and side brackets, complete all as specified and directed |
| 77 | Demolition of bricks (laid flat or on edge) or brick tiles in floors, channels, kerbs, aprons, etc (each layer) laid, bedded and pointed in any mortar including removal of debris/muds etc complete all as specified and as directed.Note : - All demolished items/ debris to be removed out side of MoD land. |
| 78 | Demolition of mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) and finally cleaning the surface with wire brush to remove old treatment to lay PCC padding complete all as specified and directed.Note : - All demolished items/ debris to be removed out side of MoD land. |
| 79 | M&L for cutting out cracks to v section in existing roofs or terrace, cleaning of grouting with cement and sand slurry 1:3, complete all as specifiedand directed. |
| 80 | M&L for providing PCC type B-1, 1:3:6(20mm graded aggregate) for providing cement concrete as levelling and roof kerbs or mud stops, including finishing the surface with grinder to receieve the acrylic based water proofing material, rounded or chamfered on edges etc complete all as specified and directed. |
| 81 | M&L for Rendering or bedding layer 15mm thick in cement mortar 1:3 cover concrete surface of roof, mixed with WPC 2% wt of cement including finishing surface even and smooth without using extra cement complete all as specified and directed(Note:- WPC shall be measured and paid separately) |
| 82 | Preparation of newly plastered surfaces of roof including cleaning the surfaces by using wire brush/ pressure hose and applying high performance polyurethene liquid membrane waterproofing coating in two coats @ 1.5 Kg/Sqm/ 2 coats with spray/ brush applied, with an elongation of 300% to 700% and tensile strength of not less than 3 N/Sqmm as per ASTM D412 and ASTM D2370, crack bridging ability of 3.5mm as per ASTM C1305, shore a hardness of not less than 60 as per ASTM D2240. The item includes applying epoxy primer @ 0.15Kg/Sqm and a geotextile of 40 GSM to be applied over first coat while first coat is still wet, complete as per manufacturer's instructions complete all as specified and directed.Note:-(i) The contractor shall submit a guarantee of 10 years the date of completion of work for waterproofing treatment alongwith manufacturer's guarantee. The amount of Rs. 40 (Rupees Forty) per Sqm and min of Rs. 4000/- for waterproofing treatment shall be withheld from contractor's in the final bill till the expiry of guarantee period. The contractor at his own option may furnish fixed deposit receipt pledged in favour of GE against guarantee money. |
| 83 | Contd/...(ii). The water proofing shall be carried out by authorized applicator of manufacturer. The name of applicator shall be got approved from GE before commencement of work. (iii) Materials shall be procured from manufacturer/authorized dealer only and original purchase voucher for the full quantity of material shall be procured by the contractor.(iv). The contractor shall enter ‘Memorandum of Understanding’ (MOU) with only one manufacturer mentioned in the contract, failing which the bid shall be liable to be rejected. |
| 84 | Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed. |
| 85 | Material and Labour for Non - skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over Screed bed or bedding layer of mortar 10 mm thick for laying floor finishes including dismantling of exsiting tiling/pcc floor/ wall any type and removing dubries outside of Md/OTM accn complete all as specified and directed. |
| 86 | Material & Labour Glazed ceramic tiles in vertical surface 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including incl 10mm thick plaster in cm 1:4 including dismantling of exsiting tiling/pcc floor/ wall any type and removing dubries outside of Md/OTM accn complete all as specified and directed. |
| 87 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings heads, shoes, bends, swan-necks, etc., incl cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed. |
| 88 | S & F in repair 75 mm dia UPVC (SWR) pipes (SCH-40) Conforming to IS 13592 single socketed, in any length with rubber ring joints, laid in trenches or in floors including all type earth work complete all as specified and directed. |
| 89 | S & F in repair 75 mm dia UPVC (SWR) pipes (SCH-40) Conforming to IS 13592 single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed. |
| 90 | S & F in repair UPVC (SWR) 110 mm dia pipes (SCH-40) Conforming to IS 13592 single socketed, in any length with rubber ring joints, laid in trenches or in floors including all type earth work complete all as specified and directed. |
| 91 | S & F in repair UPVC (SWR) 110 mm dia pipes (SCH-40) Conforming to IS 13592 single socketed, in any length with rubber ring joints, fixed on walls complete all as specified and directed. |
| 92 | S&F in repair 110 mm dia UPVC (SWR) bends any radius with oval access door complete all as specified and directed. |
| 93 | S & F in repair 75 mm dia UPVC (SWR) bends any radius complete all as specified and directed. |
| 94 | S & F in repair 75 mm dia UPVC (SWR) bends with access door any radius complete all as specified and directed. |
| 95 | S & F in repair 110 mm dia UPVC (SWR) plain bends any radius complete all as specified and directed. |
| 96 | S & F in repair 75 mm dia UPVC floor trap plain with grating including jointing with solvent cement complete all as specified and directed. |
| 97 | M&L for Mild steel work in brackets, clamps, flat iron supports, holdfasts etc., fabricated from MS flat/round/angle sections, including cutting, bending, drilling, welding, and fixing in position to hold rainwater pipes against wall, with necessary bolts, nuts, washers, and painting two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed. |
| 98 | S&F in repair 110mm UPVC junction single, (single T) equal or unequal with access door, complete all as specified and directed |
| 99 | S&F in repair 75mm UPVC junction single, (single T) equal or unequal with access door, complete all as specified and directed |
| 100 | S&F in repair 150mm x 100mm Salt-glazed stoneware gullytraps, square or round mouthed, type 'P' and setting and jointing in cement mortar 1:1, complete all as specified and directed. |
| 101 | M&L for Cutting chases pinning in , making good to facing where reqd. and pointing in CM 1:3 to ends or edges of landing , steps, cills, sunshades,selfs lintels etc. and cutting chases for conceled for water tubing or conceled condute wiring etc and making good, cutting n.exc 10cm girth.complete all as specified & as directed |
| 102 | Taking up or down steel tubing and connection including cleaning for refixing or removal to store 25mm bore pipe complete all as specified and directed. |
| 103 | Taking up or down steel tubing and connection including cleaning for refixing or removal to store 20mm bore pipe complete all as specified and directed. |
| 104 | S&F CPVC pipe 25 mm bore outer dia, PN 16, three-layer construction (Polypropylene Random Copolymer), conforming to IS:15801, UV-stabilized and anti-microbial, fusion welded type, having thermal stability suitable for hot and cold water supply systems, fixed to walls and ceilings or laid in floors including all PP-R plain and brass-threaded polypropylene random fittings, complete all as specified and directed.The pipe shall be fixed with suitable clamps at 1.00 metre spacing, and all joints shall be tested for leak-proofness to the satisfaction of the Engineer-in-Charge.The unit rate quoted shall be deemed to include all necessary fittings, cutting, jointing, fixing, alignment, supports, testing, and making good to the original finish, complete in all respects complete all as specified and directed. |
| 105 | S&F CPVC pipe 20 mm bore outer dia, PN 16, three-layer construction (Polypropylene Random Copolymer), conforming to IS:15801, UV-stabilized and anti-microbial, fusion welded type, having thermal stability suitable for hot and cold water supply systems, fixed to walls and ceilings or laid in floors including all PP-R plain and brass-threaded polypropylene random fittings, complete all as specified and directed.The pipe shall be fixed with suitable clamps at 1.00 metre spacing, and all joints shall be tested for leak-proofness to the satisfaction of the Engineer-in-Charge.The unit rate quoted shall be deemed to include all necessary fittings, cutting, jointing, fixing, alignment, supports, testing, and making good to the original finish, complete all as specified and directed. |
| 106 | S & F CPVC Gate valves (brass insert) as per requirement of the site outer dia 20 mm complete all as specified and directed. |
| 107 | S&F in repair 15 mm size bib taps cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipes complete all as specified and directed. Make : Jaquar Cat Part No OPP-CHR-15037PM or Equivalent of Kohler |
| 108 | S&F in repair 15 mm size angular cock, cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed both end for iron pipes complete.Make : Jaquar Cat Part No OPP-SSF-15053PM or Equivalent of Kohler or Grohe |
| 109 | S&F in repair central hole basin mixer for WHB cast copper alloy with capstin heads chromimium plated fancy type screwed down high pressure with or without lettered hot or cold with long screwed shank and fly nuts, screwed for iron pipe 15 mm bore complete all as specified and directed.Make : Jaquar Cat Part No CQT-CHR-23167B or Equivalent of Kohler or Grohe |
| 110 | S&F in repair Frameless Edged decorative wall looking mirror of size 600 x 450 mm, selected quality 5 mm thick , and fixed to wall with stainless steel & chromium plated round screws complete all as specified and directed. |
| 111 | S & F in repair SS soap dish complete all as specified and directed.Make: Jaquar ACN-SSF-1131N or Equivalent in Grohe or Kohler |
| 112 | S&F in repair Vitreous China Half stall type/bowl type urinal (flat back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, Waste pipe, Spreader, pointing around urinal back in cement mortar, complete all as specified and directed.Make-Jaquar Cat Par No- URS-WHT-13261H or equivalent in Grohe or Kohler |
| 113 | S&F in repairs of vitreous china wash hand basin, white, flat back of size 620 x 480x 185mm with pedestal including waste coupling, CI brackets, PVC waste pipe and connection 32 mm bore complete all as specified and directed by Engineer-in-Charge. Make- Jaquar Cat Par No- FNS-WHT-40801 or equivalent in Grohe or Kohler |
| 114 | S&F in repair PVC connections 15mm size with PTMT nuts of length 600mm, complete all as specified and directed. |
| 115 | S&F in repair stainless steel chromium plated Tumbler Holder ,complete all as specified and directedMake- Jaquar Model No- CAN-CHR-1141N or equivalent of Grohe/ Kohler |
| 116 | S&F 350 ml coloured plastic Handwash dispenser, ABS body wall mounted, complete all as specified and directed. |
| 117 | S&F in repair decorated type towel ring round with round flange with chromium plated finish, complete all as specified and directedMake- Jaquar Cat Par No- ACN-CHR-1121BN or equivalent in Grohe or Kohler |
| 118 | S&F in repair 15 mm size 2-Way bib taps cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipes complete all as specified and directed.Make : Jaquar Cat Par No- ARI-CHR-39041 or Equivalent of Kohler/Grohe |
| 119 | S&F in repair Health faucet (Hand shower) with 1 metre flexible tube with wall hook, Chromium Plated as specified and as directed by the Engineer-in-Charge. Make : Jaquar Cat Part No ALD-CHR-573 or Equivalent of Kohler Or Grohe |
| 120 | S&F in repair Vitreous china squatting pan of Orissa pattern of approved make of size 580mm x 440mm white with integral foot rest, including 10 ltrs PVC valveless, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, flush pipe of polythylene of low or high density or PVC 32mm dia, including trap set in and including concrete bedding and connection to antisyphonage pipe etc, including making good to floor, complete all as specified and as directed. Make :CERA Cat Par No- Cable S3020105 or equivalent in Make list Appx \\"D\\" of PS. |
| 121 | S&F in repair Vitreous china wash down water closet pedestral pan white, rectangular shape including 10 ltrs PVC valveless, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, flush pipe of polythylene of low or high density or PVC 32mm dia, Plastic water closet seat, closed pattern with recessed bottom, and cover and mild steel chromium plated or aluminium hanging device, complete all as specified and as directed. Make: CERA Cat Par No- CELEB S S1053130 or equivalent in Make list Appx \\"D\\" of PS. |
| 122 | Supply and fix 500 liters capacity white colour triple layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 20 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete and including dismantling of old tank complete all as specified and directed. |
| 123 | Demolition of brick work built in CM complete all as specified and as directed. |
| 124 | M&L brick work with fly ash bricks straight or curved on plan exceeding 6 m mean radius built in CM 1: 6 complete all as specified and as directed. |
| 125 | M&L brick work with sub class B bricks straight or curved on plan to any radius built in Half brick thick wall built in CM 1: 6 complete all as specified and as directed. |
| 126 | Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed.Note: All demolished items/debris to be removed out of MOD land. |
| 127 | M&L for Precast Cement Concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in manhole covers etc. complete all as specified and directed by Engineer-in-Charge. |
| 128 | M&L for mild steel TMT bars 10 mm dia and over in reinforcement cut to length bent to shape required incl cranking bending, spirally for hooping for column, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia all as specified and as directed. |
| 129 | M&L for Coloured Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bedding in cement mortar (1:4) complete all as specified and as directed. |
| 130 | M&L for Coloured Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in vertical surface, skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed. |
| 131 | M&L for vitrified tile double charged/ Glossy finish, 8-9 mm thick (square/rectangular) polished, area of each tile n exc 0.42 sqm but Nexc 1.00 sqm in floor etc set and jointed in neat cement slurry over 15 mm thick screed bed in CM 1:4 and pointed in white or coloured cement to match the shade, complete all as specified and directed |
| 132 | M&L double charged/Glossy finish vitrified tile 8-9mm thick (square/rectangular) area of each tile not exceeding 0.42 sqm but n exc 1.00 sqm, in vertical surface such as skirtings, dodos set and jointed in neat cement slurry over 10mm thick CM (1:4) plaster and pointed in white or coloured cement to match with the tiles complete all as specified and directed. |
| 133 | Demolition of existing sewage line and Supply & laying, jointing and testing in trenches DWCPE SN 8) nominal size 175 (ID)/200(OD) dia as per IS-16098 (Part-2): 2013 upto a depth of 1.8 m with and including all items and activities like PCC Bed, Haunching & Benching against two pipes, required to make sewer line functional complete all as specified and as directed. |
| 134 | Cutting into existing manholes for connecting new drains of internal dia of pipe, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specified and as directed. |
| 135 | Demolition of cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) incl chequered tiling and Paver blocks complete all as specified and as directed. |
| 136 | Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and as directed. |
| 137 | M&L for 18-19 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms (including a hole of gas pipe) and like incl 15 mm thick screed bed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed. |
| 138 | Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and similar situations complete all as specified and as directed. |
| 139 | Supplying and fixing polished black granite inauguration plate of size 600mm x 900mm x 18-20mm thick, with machine-cut edges, mirror finish, and engraving of text/logo as per approved design including gold paint filling in letters, fixing with stainless steel clamps and necessary adhesive, complete all as specified and directed by Engineer-in-Charge. |
| 140 | M&L for 1st quality non skid coloured Heavy duty, Matt finish tiles of size 300mm x 600mm, 12 mm thick set and jointed in neat cement slurry & pointed with coloured cement to match in floor over and including including 15 mm thick screed bed in cement mortar (1:4) and 25 mm thick levelling corse of PCC 1:2:4 using 12.5 mm crushed stone aggregate complete all as specified and directed. |
| 141 | M&L for 75mm thick PCC type D-2, 1:4:8 (using 40 mm graded aggregate) as in sub base of flooring and hardstanding,complete all as specified and directed. |
| 142 | Taking down carefully copper/aluminum point wiring (light/fan/socket power) complete , including fixture and fitting such as switches, ceilling roses, pendants, regulators, socket, light fittings etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per condition seperately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed. |
| 143 | M&L for point wiring of light/fan/bell with PVC insulated FRLS unsheathed single core cable of multistranded copper conductor of size 1.5 sqmm as phase & neutral drawn in and including PVC conduit medium grade not less than 20 mm dia, ISI marked, duly concealed to wall/floor or above false ceiling of suitable size with all fitting and accessories laid on wall/ceiling alongwith 1.5 sqmm stranded PVC insulated FRLS unsheathed copper conductor(Green in color) as earth wire and connected to common earth dolly for the following incl making good to surface with CM(1:4) plaster and paint to match the surface complete incl provn of electrogalvanised steel terminal switch box and white bakelite plastic laminated top sheet cover and fixed with brass screws cup washer for fixing switches/socket/regulators etc complete all as specified and directed. |
| 144 | All as per item No 141 above but for One 5 pin 5 amps socket outlet on same board with cables of size 2.5 sqmm |
| 145 | All as per item No. 141 above but for One 5 pin 5 amps socket outlet on independent board with cables of size 2.5 sqmm |
| 146 | All as per item No. 141 above but for One 6 pin 15/16 amps socket outlet on independent board with cables of size 2.5 sqmm |
| 147 | All as per item No. 141 above but for on independent board with cables of size 4 sqmm (geyser point/AC Point) complete. |
| 148 | S&F Switch piano flush button single pole one way 5 Amp complete all as specified and directed. |
| 149 | S&F socket outlet flush type 3/5 pin 5/6 Amps 230V AC complete all as specified and directed. |
| 150 | S&F switch piano flush single pole one way 15/16 Amps complete all as specified and directed. |
| 151 | S&F socket outlet flush type 5/6 pin 15 Amps 230V AC complete all as specified and directed. |
| 152 | S&F ceiling rose 3 terminal / PVC/ polycarbonate, isolated body complete all as specified and directed. |
| 153 | S&F rotary Step type electronic fan regulator 100W, flush type complete all as specified and directed. |
| 154 | S&F Lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed. |
| 155 | Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. |
| 156 | Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. |
| 157 | S&F single pole and neutral sheet metal enclosure with two pin and earth plug and socket complete with & including one number MCB SP 20/25 Amps, complete all as specified and directed. |
| 158 | S&F TPN DB double door 4 way 415V incl busbar double door and other accessories without MCB complete all as specified and directed. |
| 159 | S&F MCB DB SPN 8 way with 100 amps 240 volts rated copper busbar in sheet steel enclosure.double door type complete all as specified and directed. |
| 160 | Supply & fixing MCB , SP, AC, 240 volts of 06 to 32 Amps capacity 10KA, 'C' series and making connections with suitable size of copper lugs complete all as specified & directed. |
| 161 | Supply & fixing MCB, SPN, AC, 240 volts of 32 Amps capacity 10KA, 'B' series and making connections with suitable size of copper lugs complete all as specified & directed. |
| 162 | Supply & fixing MCB , TPN, AC, 415 volts of 100 Amps capacity 10KA, 'C' series and making connections with suitable size of copper lugs complete all as specified & directed. Please Enable Macros to View BoQ information |
| 163 | Supply & fixing MCB , TPN, AC, 415 volts of 100 Amps capacity 10KA, 'C' series and making connections with suitable size of copper lugs complete all as specified & directed. Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
