|
| 1 | Schedule 'A' B/R |
| 2 | Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises, complete all as specified and directed by Engineer-in-Charge. |
| 3 | Demolition of stone slabs and tiles of any description or thickness in floors, aprons Laid, bedded and pointed in any mortar etc., complete all as specified and directed by Engineer-in-Charge. |
| 4 | Taking down chowkhat with shutters (without taking of shutters from the frames of any description not exceeding 1.5 sqm in each panel, complete all as specified and directed by Engineer-in-Charge. |
| 5 | Taking down chowkhat with shutters (without taking of shutters from the frames of any description exceeding 1.5 sqm but not exceeding 4 sqm in each panel, complete all as specified and directed by Engineer-in-Charge. |
| 6 | Dismantling of mild steel work as in angle iron frames/grills mild steel bars etc., complete all as specified and directed by Engineer-in-Charge. |
| 7 | Demolition of Concrete of any description and in any position not otherwise specifically provided, complete all as specified and directed by Engineer-in-Charge. |
| 8 | Dismantling/ Demolition of brick work or stone masonry or RCC Pre cast Jali & Jafari built in cement mortar including all quoins, arches, pillars, etc., complete all as specified and directed by Engineer-in-Charge. |
| 9 | Taking down cement plaster on stone wall including racking out joints, hacking for key scrubbing with water etc., complete all as specified and directed by Engineer-in-Charge. |
| 10 | Supply & Fixing 2nd class HW plain chowkhats and framed, rebated on the solid rounded or chamfered put together with glue pinned at joints, complete all as specified and directed by Engineer-in-Charge. |
| 11 | Supply & Fixing 35mm thick Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc. as specified in SSR Part I, Section 8, clause 8.20 (a), complete all as specified and directed by Engineer-in-Charge. |
| 12 | Supply & Fixing 35mm thick Flush Shutter, solid core construction, with block board core and plywood face panels, both face is covered with decorative face veneer with lipping/ frame to match commercial type on both side, complete all as specified and directed by Engineer-in-Charge. |
| 13 | Supply & Fixing Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing, complete all as specified and directed by Engineer-in-Charge. |
| 14 | Supply & Fixing Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing, complete all as specified and directed by Engineer-in-Charge. |
| 15 | Supply & Fixing for factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (±0.2mm). Window profile with hollow section with multi chamber, frame (88mm x 52mm), sliding sash (42mm x 67mm), sliding interlock (one vertical length in each shutter) (45.5mm x 28mm), glazing bead (24.5mm x 16mm) will be mitered cut and fusion welded at all corners, including railing of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM gasket. 1.2 ±0.2mm thick galvanized steel frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm) 2nos, sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fastener. Hardware (touch lock of zinc alloyed (white powder coated), steel roller system, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate excludes cost of glass and includes all other connected accessories) area not exceeding 2.00 sqm each fixed from ground floor to height of any floors, complete all as specified and directed by Engineer-in-Charge. |
| 16 | Supply & Fixing 7mm thick aluminium grills of make \\"Deco grill\\" model DG 104 surrounded by aluminium 'C' channel and size of opening 75x75 mm all as specified and directed fixed from ground floor to height of any floors, complete all as specified and directed by Engineer-in-Charge. |
| 17 | Supply & Fixing 18-19mm thick factory made 100% solid WPC (Wood polymer composite) Solid Plain / Prelam / Enrouted Plain / Enrouted Painted flush Door Shutter of required size comprising of Virgin PVC resin of K Value 57-60 (Suspension Grade), Calcium carbonate and natural fibres (Wood Powders/rice husk / Wheat husk) and Non-toxic additives made from Extrusion process WPC foam sheet single Extruded (Inner) with density not less than 650 Kg/cum manufacture by an ISO 9001-2015 Certified Company, having good screw holding capacity (Screw withdrawal strength of 2000 N (face) & 1100 N (Edge), Minimum Compressive Strength of 50 N/mm2, Modulus of elasticity 850 N/mm2 and resistance of spread flame of Class A category with Property of being Termite/Borer Free, Water/Moisture Proof, Fire Retardant and fixing with Stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws for WC / Bathroom / Toilet / Kitchen / Balcony Doors, complete all as specified and directed by Engineer-in-Charge. |
| 18 | Material & Labour for preparation of new or previously treated wood surfaces of any description, over 10 cm width or girth, not otherwise described applying one coat of pink primer and applying two coat of synthetic enamel paint, complete all as specified and directed by Engineer-in-Charge. |
| 19 | Supply & Fixing 300mm long brass ordinary rat tail rod pattern springs including roller and roller, complete all as specified and directed by Engineer-in-Charge. |
| 20 | Supply & Fixing 100mm long Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21, complete all as specified and directed by Engineer-in-Charge. |
| 21 | Supply & Fixing 150mm long Extruded Aluminium alloy handles, fabricated type, and anodised, complete all as specified and directed by Engineer-in-Charge. |
| 22 | Supply & Fixing 150mm long Aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed by Engineer-in-Charge. |
| 23 | Supply & Fixing 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy, complete all as specified and directed by Engineer-in-Charge. |
| 24 | Supply & Fixing Hasp and staple for 100mm, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws, complete all as specified and directed by Engineer-in-Charge. |
| 25 | Supply & Fixing 140mm long aluminium anodized floor door stopper double legged with rubber shoe, fixed to bottom rail of door, complete all as specified and directed by Engineer-in-Charge. |
| 26 | Supply & Fixing 4mm thick Figured glass, pin headed type and glazing with oil putty in squares not exceeding 0.5 Sqm in each panel, complete all as specified and directed by Engineer-in-Charge. |
| 27 | Supply & Fixing stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium/pvc sections, complete all as specified and directed by Engineer-in-Charge. |
| 28 | Material & Labour for 10mm thick vitrified tile of area exceeding not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over screed bed or bedding layer of mortar 15 mm thick Cement Mortar 1:6, complete all as specified and directed by Engineer-in-Charge. |
| 29 | Material & Labour for 10mm thick vitrified tile of area exceeding not exceeding 0.36 sqm in vertical surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match over cement mortar 15 mm thick Cement Mortar 1:4, complete all as specified and directed by Engineer-in-Charge. |
| 30 | Material & Labour for PCC (1:2:4) type B-0 using 12.5mm graded aggregate as in floor of average 25 mm thick, complete all as specified and directed by Engineer-in-Charge. |
| 31 | Material & Labour for granite (of any type) 20mm thick (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including, grinding, polishing, moulding the edges and polishing and including over screed bed 20mm thick in cement mortar 1:6, complete all as specified and directed by Engineer-in-Charge. |
| 32 | Material & Labour for Porbandar stone masonry, well bonded, bedded and solidly hearted built in Cement Mortar 1:6, complete all as specified and directed by Engineer-in-Charge. |
| 33 | Material & Labour for rendering 5mm thick on ceiling concrete surfaces in cement mortar 1:3 and even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge. |
| 34 | Material & Labour for rendering 15mm thick on stone surfaces in cement mortar 1:4 and even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge. |
| 35 | Material & Labour 15mm thick rendering in Cement Mortar 1:6 to stone surfaces trowelled to even & smooth w/o using extra cement, complete all as specified and directed by Engineer-in-Charge. |
| 36 | Material & Labour for preparing surfaces plastered or un-plastered new surface of walls applying two coats of oil bound distemper over a coat of primer over layer of smooth Putty finish as per manufacture instruction with smooth roller finish, complete all as specified and directed by Engineer-in-Charge. Note: - After painting, cleaning of all floors, glass & Furniture by own arrangement. |
| 37 | Material & Labour for complete removal of existing treatment by washing down and smoothing old surface of walls including scrapping and applying two coats of oil bound distemper over a coat of primer over layer of smooth Putty finish two coats as per manufacture instruction with smooth roller finish, complete all as specified and directed by Engineer-in-Charge. Note: - After painting, cleaning of all floors, glass & Furniture by own arrangement. |
| 38 | Material & Labour for preparing surfaces plastered or un-plastered new surface of ceiling applying two coats of oil bound distemper over a coat of primer on smooth putty finish two coats as per manufacture instruction with smooth roller finish, complete all as specified and directed by Engineer-in-Charge. Note: - After painting, cleaning of all floors, glass & Furniture by own arrangement. |
| 39 | Material & Labour for preparing surfaces plastered or un-plastered old surface of ceiling applying two coats of oil bound distemper over a coat of primer two coats as per manufacture instruction with smooth roller finish, complete all as specified and directed by Engineer-in-Charge. Note: - After painting, cleaning of all floors, glass & Furniture by own arrangement. |
| 40 | Material & Labour for preparation of new plastered surfaces of wall and applying two coats of 100 % Premium acrylic emulsion paint having VOC less than 50 gm/ltrs and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over a coat of smooth putty all as per the manufacturer’s instructions, complete all as specified and directed by Engineer-in-Charge. |
| 41 | Supply & Fixing in repair 15mm bib tap (fancy type), cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and directed by Engineer-in-Charge. |
| 42 | Supply & Fixing in repairs brass CP shower rose 125mm size fancy type with swivel joint any size including fixing to steel pipe/union for 15mm dia., complete all as specified and directed by Engineer-in-Charge. |
| 43 | Supply & Fixing in repair PVC connection of 15mm dia length 600mm, complete all as specified and directed by Engineer-in-Charge. |
| 44 | Supply & Fixing in repair single piece EWC of minimum dimensions 600x350x700 mm with seat cover, flushing cistern fitting, fixing accessories, S/P trap complete as specified and as directed by Engineer-in-charge |
| 45 | Supply & Fixing for Bevelled edge mirror, 600mmx450mm of selected quality glass, mounted on 6 mm thick or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers fixed in repairs. |
| 46 | Supply & Fixing for in repair 20mm Aluminium anodised Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified |
| 47 | Supply & Fixing in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position, complete all as specified and directed by Engineer-in-Charge. |
| 48 | Supply & Fixing in repair 15mm bore stop valves/ Angle valve, cast copper alloy fancy type screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions, complete all as specified and directed by Engineer-in-Charge. |
| 49 | Supply & Fixing in repair 15mm dia CP two way angle valve fixed in pipe, complete all as specified and directed by Engineer-in-Charge. |
| 50 | Supply & Fixing in repair Stop valves/Angle valves of size 15mm dia fancy type, chromium plated with long shank and cup (concealed type), screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as specified and directed by Engineer-in-Charge. |
| 51 | Supply & Fixing in repair Harrison rails stainless steel (Curtain rod/drapery rod), 20mm dia, powder coated with and including fancy type bracket 2 Nos of each opening and side stopper fancy type powder coated of required shape and size 2 Nos of each opening, complete all as specified and directed by Engineer-in-Charge. |
| 52 | Supply only liquid water proofing compound, complete all as specified and directed by Engineer-in-Charge. |
| 53 | Supply & Fixing Joist, channel, angle, or tee sections, tube Fe-410-W (Gde- E-250) quality-B fixed independently, without connecting plates, etc., complete all as specified and directed by Engineer-in-Charge. |
| 54 | Material & Labour for preparing new surface of steel of any desc over 10 cm width or girth and applying two coat of synthetic enamel paint over red oxide, complete all as specified and directed by Engineer-in-Charge. |
| 55 | Material & Labour for PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in filling in chowkhats, hold fast block etc., complete all as specified and directed by Engineer-in-Charge. |
| 56 | Supply & Fixing in repair Grating doom 100mm dia of PTMT (Minimum weight 25gms), complete all as specified and directed by Engineer-in-Charge. |
| 57 | Supply & Fixing anodised aluminium snap grid frame work size of grid 605mm x 605mm for false ceiling, complete all as specified and directed by Engineer-in-Charge. |
| 58 | Supply & Fixing Hangers 6mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long, complete all as specified and directed by Engineer-in-Charge. |
| 59 | Supply & Fixing 4mm thick PVC false ceiling tile of size 595mm x 595mm, complete all as specified and directed by Engineer-in-Charge. |
| 60 | Material and labour for powder coated Aluminium Anodised frame (minimum thickness of powder coating 50 micron) for door, sliding windows & ventilators with one or more rebates including joining cleats for fixing etc., complete all as specified and directed by Engineer-in-Charge. |
| 61 | Material and labour for powder coated Anodised aluminium door/ window shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc., complete all as specified and directed by Engineer-in-Charge. |
| 62 | Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed by Engineer-in-Charge. |
| 63 | Supply & Fixing Pre-painted galvalume aluminium zinc coating GI based corrugated sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self-tapping screw, complete all as specified and directed by Engineer-in-Charge. |
| 64 | Material & Labour for precast RCC 1:2:4 Type-B1 (using 20mm graded crushed stone aggregate) as in Providing precast cement concrete in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, anchorage blocks, bonders (for stone walling). corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, weathering’s, throating etc. and setting in mortar complete with joints to match set in Cement Mortar 1:4, complete all as specified and directed by Engineer-in-Charge. |
| 65 | Material & Labour for Mild CRS TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia or securing with clips, complete all as specified and directed by Engineer-in-Charge. |
| 66 | -ditto- all as per item No.64 above, but 5mm dia and over upto 10mm dia as in stirrups, spacers and binders, complete all as specified and directed by Engineer-in-Charge. |
| 67 | Excavating in trenches, not exceeding 1.5 Metre wide and not exceeding 1.5 Metre depth for foundation, etc or not exceeding 10 Sqm on plan and not exceeding 1.5 Metre in depth for shafts, cesspits, manholes, pier holes, etc and getting out in loose/soft soil, complete all as specified and directed by Engineer-in-Charge. |
| 68 | Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm each, complete all as specified and directed by Engineer-in-Charge. |
| 69 | Removing excavated soil not exceeding 50 Metre and depositing where directed at a level not exceeding 1.5 Metre above the starting point, complete all as specified and directed by Engineer-in-Charge. |
| 70 | Material & Labour for complete removal of existing treatment of old steel surface of any desc over 10 cm width or girth and applying two coat of synthetic enamel paint over red oxide, complete all as specified and directed by Engineer-in-Charge. |
| 71 | Supply & Fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber / neoprene gasket etc., Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, complete all as specified and directions by Engineer-in-Charge. |
| 72 | Supply & Fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc., Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, complete all as specified and directions by Engineer-in-Charge. |
| 73 | Supply & Fixing 5mm thick Figured glass, pin headed type and glazing with oil putty in squares not exceeding 0.5 Sqm in each panel, complete all as specified and directions by Engineer-in-Charge. |
| 74 | Material & Labour for weld-mesh of size 25x25x3mm to be wrapped on the exposed surface of rib of beam & on the slab bottom and tack welding to the exposed reinforcement at close intervals and applying Cement Mortar 1:3 upto original thickness all in complete as per the technical specifications and manufacturer's instructions, complete all as specified and directions by Engineer-in-Charge. |
| 75 | Material & Labour for complete removal of old plastered surfaces of wall and applying two coats of 100 % Premium acrylic emulsion paint having VOC less than 50 gm/ltrs and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over a coat of smooth putty all as per the manufacturer’s instructions, complete all as specified and directions by Engineer-in-Charge. |
| 76 | Schedule 'A' E/M |
| 77 | Taking down carefully aluminium / copper point wiring complete for light, fan, socket or power point etc., with fittings fixtures such as ceiling rose, holders, electric fittings, switches, sockets, aluminium conductor cable with and including wooden batten or FR PVC conduit and its accessories such as wooden gutties, raw plugs, GI screws, aluminium clips, nails etc., complete and removing the material from site and making good the disturbed surface of wall / floor/ ceiling etc., as original i.e. brick work, plastering, white washing, OBD etc., as required, complete all as specified and directed by Engineer-in-Charge. |
| 78 | Taking down carefully UNSV main switch and DB's including MCBs of any size make, type and capacity and depositing at site, complete all as specified and directed by Engineer-in-Charge. |
| 79 | Material & Labour for Point wiring (Concealed) using approved colour coding as per IS Red / Yellow / Blue, Black and green for single phase circuits) with multi stranded copper conductor 1.5 Sqmm nominal cross area single core PVC insulated and unsheathed FRLS cable 1100 Volts grade ISI 694 marked with valid CML No. in and including medium grade PVC concealed conduit of dia not less than 20mm and conduit accessories ISI marked with valid CML No. (IS 9537-1983) for wall / roof / floor etc., with pressed flush metal boxes covered with inner plates & outer plates etc., suitable for mounting of Modular switches & sockets including PVC insulated multi stranded copper conductor FRLS 1.5 sqmm nominal cross sectional area single core FRLS cable as earth continually conductor to common earth and connecting to earth dolly, complete all as specified and directed by Engineer-in-Charge.for the following:- |
| 80 | One light point controlled by one, one way switch |
| 81 | One socket outlet 3 pin, 5 Amps on independent board, controlled by one no 5 Amp switch. |
| 82 | One socket outlet 3 pin 5 amps on the same board controlled by one no 5 Amp switch. |
| 83 | All as per srl item no. 78 here-in-before but with 2.5 sqmm FRLS copper wire with 2.5 Sqmm FRLS copper earth wire for independent 15 Amp point. |
| 84 | Supply & Fixing Modular switch flush type single pole one way 6 Amp ISI Marked, complete all as specified and directed by Engineer-in-Charge. |
| 85 | Supply & Fixing Modular switch flush type single pole one way 16 Amp ISI Marked, complete all as specified and directed by Engineer-in-Charge. |
| 86 | Supply & Fixing Modular socket outlet 2 in 1, 3 pin, 6 Amp, 230 Volts flush type, complete all as specified and directed by Engineer-in-Charge. |
| 87 | Supply & Fixing Modular socket outlet shutter type 2 in 1, 6 pin, 5 and 16 amp flush type, 230 Volts ISI Marked, complete all as specified and directed by Engineer-in-Charge. |
| 88 | Supply & Fixing bldg security LED Light Luminaire of 35 Watts having IP 65 protection fitting made out of pressure die cast Aluminium housing, operating Voltage 140-270 Volts within built surge protector, toughened glass with and including GI pipe 40mm bracket of 1.5 m in length including drilling holes, nuts & bolts 2 coats of red oxide primer on GI pipe and fixing with wall security light on building wall connecting cable, complete all as specified and directed by Engineer-in-Charge. |
| 89 | Supply & Fixing 2'x2' energy efficient recess/surface mounting 36 Watt LED luminaries suitable for fixing at POP/2'x2' snap grid false ceiling housing LED lamp and other accessories complete warm white/white, complete all as specified and directed by Engineer-in-Charge. |
| 90 | Supply & Fixing of MCB DB sheet enclosure double door type, triple pole and neutral 415 V with standard bus bar of suitable size plate and common neutral link all enclosed in standard steel sheet flush mounting type factory fabricated complete without MCB and with enclosure blank plates for unused way suitable for 6 way type, complete all as specified and directed by Engineer-in-Charge. |
| 91 | Supply & Fixing Decorative wall light made up of high grade engineering plastic material suitable for and including 9 W LED lamp(Warm White/White), complete all as specified and directed by Engineer-in-Charge. |
| 92 | Supply & Fixing MCB, B Curve type, 10 kA, 63Amp, SPN with over load and short circuit protection, complete all as specified and directed by Engineer-in-Charge. |
| 93 | Supply & Fixing MCB, B Curve type, 10 kA, 6 to 32 Amp, Single Pole with over load and short circuit protection, complete all as specified and directed by Engineer-in-Charge. |
| 94 | Supply and fixing MCB DB SPN (double door) 8 Ways including bus bar neutral link, earth bar and din rail, recessed with wall surfaces by chase cutting and making good surfaces of wall, complete all as specified and directed by Engineer-in-Charge. |
| 95 | Material & Labour for sub main wiring with 2 run of 6 Sqmm FRLS, PVC insulated, unsheathed and stranded copper conductor cable with and including 6 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable as earth wire connected with thimble from main DB to sub main DB, drawn in to separate concealed medium grade, ISI marked, non-metallic PVC conduit 15mm dia size including all conduit accessories & Fittings / junction boxes / inspection covers etc., with and including cutting chasing and making good of disturbed surface of wall / floor/ ceiling etc., as original by brick work, plastering, white washing, OBD etc., as required, including taking down old unserviceable sub maain wiring, complete all as specified and directed by Engineer-in-Charge.Note:- Two run of 6 Sqmm and one run of 6 Sqmm (earth wire) cable including one run of conduit pipe will be measured as one length including making good the disturbed surfaces. |
| 96 | Material & Labour for in repairs Earthing complete with galvanised steel earth electrode 60cm x 60cm x 6mm buried directly in ground vertically to depth not less than 2.25m below normal ground level with top edge of the earth plate at a depth not less than 1.5m below ground level connected to and including GI earth lead wire 4mm dia by means of nuts, bolts, check nuts and washer etc, made of GI and connected to test point and earth dolly all as shown in electrical plate No. 3 SSR Part-I 2009 and specified or indicated including excavation and earthwork in any type of soil PCC (1:3:6) Type C-1 in chamber, precast RCC 50mm thick in cement concrete (1:2:4) type B-1, reinforced with welded steel wire fabric or XPM (Weight not less than 4.00 mm dia with cast iron frame, funnel with wire mesh, 20mm bore medium grade GI watering pipe, lugs, 15mm bore medium grade GI protection pipe, test point etc., complete all as specified and directed by Engineer-in-Charge.Note:- (i) Item includes the cost of 7.5 metre GI pipe for protection of earth lead. (ii) Item includes the cost of 7.5 metre GI earth lead. |
| 97 | Supply, laying testing in trenches LT UG XLPE insulated, armoured, heavy duty electric cable, aluminium conductor, 1100 V grade, cross sectional area 16 sqmm 4 core, complete all as specified and directed by Engineer-in-Charge.Note : Earth work and brick work measured and paid separately |
| 98 | Supply and laying double wall corrugated (DWC) 50/38mm outer dia high density polythene pipes having corrugation on the outer wall and plain surface on the inner wall confirming to ISI 14930 (Part I and II) for protection of underground cables laid in trenches / road/ nallah or fixed along wall. poles or laid under floor (including cutting floor/Road and making good to match with existing adjoining surface etc., for cable protection, complete all as specified and directed by Engineer-in-Charge.Make: Rex/Poly/Gemini |
| 99 | Supply and fixing MCB TPN C Curve 63 Amps, complete all as specified and directed by Engineer-in-Charge. |
| 100 | Supply & Fixing wall fan portable type with three leaf for air circulation of size 400mm Sweep, complete all as specified and directed by Engineer-in-Charge. |
| 101 | Supply & Fixing 300 watts LED Search light, high intensity, energy saving, long range, multi-functional, auto-swivel LED search light, beam range 700 meters, 130 W in multi circuit LED, Efficacy> 110 Im/w, CCT 5500K, LM6 housing with heat ink round in shape, dia >440mm, operating voltage 90V- 300V, 50hz, PF 0.95, THD 10% CCT 5500K, CRI>70 Optics used PMMA/PC lens, LED efficacy 140 Uw, average lux level at 10 meter> 9000 with circle of approx Imeter, toughened clear glass with silicon gasket, over volt / under volt & short circuit protected, confirming to LM79, LM10 IK07, IP66, IS 10322 pts secs (Type Tested) and BIS approved. This search-light should be installed on dne of revolving mechanism with suitable motor-gear unit and designed to rotate 360 continuously over the night in horizontal plane with speed controller (1 to 10 rpm), auto/ manual, Rev. / Farw, and Up/Down push buttons for tilting up to 45 degree A separate wall mounted wired control panci (consist of MCB's, V-meter, Fuse, LED indicators) is supplied for smooth & safe operation remotely. The revolving mechanism is fully covered with weather & rust proof fibre box with maintenance window/ door, provision of foundation holes at bottom for proper installation, complete all as specified and directed by Engineer-in-Charge. |
| 102 | Material & Labour for sub main wiring with two single core 2 x 6 Sqmm PVC (FRLS) insulated multi-stranded flexible copper conductor cable 660/1100 volts grade down in through including Concealed PVC Conduit with all accessories, PVC insulated 1 x 6 Sqmm single core single strand copper conductor as continuous earth wire in green colour connected to common earth dolly, complete all as specified and directed by Engineer-in-Charge. Note: 1. Two runs of cable, one run of earth wire, one run of PVC conduit will be measured and paid one unit. |
| 103 | Material & Labour for sub main wiring with two single core 2 x 2.5 Sqmm PVC (FRLS) insulated multi-stranded flexible copper conductor cable 660/1100 volts grade down in through including Concealed PVC Conduit with all accessories, PVC insulated 1 x 2.5 Sqmm single core single strand copper conductor as continuous earth wire in green colour connected to common earth dolly, complete all as specified and directed by Engineer-in-Charge. Note: 1. Two runs of cable, one run of earth wire, one run of PVC conduit will be measured and paid one unit. |
| 104 | Material & Labour for Earthing complete with galvanised steel earth plate electrode 60cm×60cm× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less ‘than 1.5 metres below normal ground level, connected to galvanised earth lead galvanised iron strip 25×4mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to Earthing test point all as specified or indicated including testing, complete all as specified and directed by Engineer-in-Charge. Please Enable Macros to View BoQ information |
