|
| 1 | Taking down cement plaster of any description including racking out joints, hacking for key scrubbing down with water etc and removal of entire debris as ordered outside MD land complete all as directed. |
| 2 | Demolition of cement concrete (un-reinforced) in ground floor and paving not exceeding 15 cm thick above or below ground level and removal of entire debris as ordered outside MD land complete all as directed. |
| 3 | Taking down chowkats or frames not exc 1.5 sqm each with shutters (without taking off shutters from frame) and stacking at site where directed. |
| 4 | All as per item 4 here-in-above but exceeding 1.5 Sqm but not exceeding 4 Sqm each |
| 5 | Taking down shutter of any description not exc 1Sqm each and stacking at site where directed. |
| 6 | All as per item 5 here-in-above but exceeding 1 Sqm but not exceeding 2 Sqm each -do- |
| 7 | Dismantling of wrought iron or mild steel work of any description not otherwise provided for in this Schedule all as directed. |
| 8 | Dismantling structural steel any type of steel including gates , purlins , rafters / roof coverings materials laid in walls excluding trusses complete all as specified and as directed. |
| 9 | Dismantling of Corrugated or semi corrugated steel sheeting etc any thickness including ridges as in roof covering and stacking at site where directed and removal of debris to a distance not exceeding 50 mtr and depositing where directed complete all as directed. |
| 10 | Dismantling of AC Corrugated or semi corrugated sheet etc any thickness including ridges as in roof covering and stacking at site at site for credit where directed and removal of debris to a outside MOD land and depositing where directed complete all as directed. |
| 11 | Dismantling single layer mangalore pattern roof tiles including ridges laid and set in cement mortar complete all as directed. |
| 12 | Dismantling ceiling boarding of any description fixed in any position with nails incl cover fillets/aluminium snap grid. |
| 13 | Dismantling floor, hearth or wall tiling inluding cement mortar bedding (but not backing), stacking serviceable tiles at site and removal of entire debris as ordered outside MD land complete all as directed. |
| 14 | M&L for P.C.C 1:2:4 type B-0 using 12.5 mm graded crushed stone aggregate as in coping and on roof/benching over chajja etc complete all as specified and as directed. |
| 15 | M&L for P.C.C 1:2:4 type B-0 using 12.5 mm graded crushed stone aggregate as in roof kerb of hanger roof ( in a height upto 13 Mts form Ground level) complete all as specified and as directed. |
| 16 | Supply only Integral Water Proofing Compound (ISI Marked) of Make : CICO, Acco Proof, Impermo, Aqua flex as approved. |
| 17 | S&F Second class hard wood factory made kiln - seasoned, plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints and fixed in position complete all as directed. |
| 18 | S&F solid PVC door frame of size 50X47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in opening as per specification all as directed. |
| 19 | Supply and fixing factory made 35 mm thick plain framed, paneled shutter (Two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces, size of rail and styles as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated using second class Hard Wood rail and styles, fixed to chowkat, complete all as specified & directed |
| 20 | S &F 35 mm thick second class hard wood factory made glazed and skeleton shutter open rebated and prepared to receive glass, guage etc edge of framing plain chamfered or rounded fitted with cut and mitred beads for securing guage etc size of members of shutter as specified in SSR Part I Section 8 clause 8.24 (a) supplied and fitted to chowkats. |
| 21 | All as per serial item No 29 here-in-before 30 mm thick shutter as in windows, ventilators, etc. provided with stiles and rails as specified in SSR Part I, Section 8 clause 8.24(b). |
| 22 | S&F 40 mm thick Flush shutters, solid core construction, with block board core & plywood face panels both faces are covered with decorative face veneer conforming to IS 2202 (Part- I) -1999, including internal liping beading all round fitted to chowkats all as specified |
| 23 | S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strips of 20 mm width stuck inside with solvent cement for stiles and single sides prelam PVC sheet and stile & rails having one side feathered edge and on other side 10mm (90°) bent edges & as gap insert for top rail & bottom rail; Panelling to be fitted in the M.S. frame welded/ sealed to the styles & rail with suitable PVC sheet beading, and joint together with solvent cement, all as specification and drawing. |
| 24 | S&F for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screwshaving minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia andlength complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). |
| 25 | All same as per item No 24 here-in-above but frame size 65x 100 mm (double rebate) -do - |
| 26 | S&F 28-30 mm thick Prelaminated WPC factory made 100% Sketon/Glazed door (conforming as per IS-4020) made from 100% lead free single extruded on both side with wood grain texture and with density not less than 650 Kg/cum. Manufactured by an ISO : 9001-2015 certified company. The door should be water proof, termite proof, fire etardant and having screw holding capacity complete all as specified |
| 27 | All same as per item No 26 here-in-above but solid door -do - |
| 28 | M&L for 18/19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work/hinges as in cupboard shutters, shelves, Kitchen cabinets etc with & including necessary 18/19mm wide & 6mm thick Teak wood beading / edging / lipping fixed with nails to particle board complete all as specified & as directed. |
| 29 | S&F 100 mm long Butt hinges, extruded aluminium ally with galvanished mild steel hinge pin anodised and fixed type B-21 |
| 30 | S&F mild steel butt hinges medium weight cold rolled 100 mm size |
| 31 | S & F 100 mm size aluminium anodised barrel tower bolt of extruded section . |
| 32 | S&F 300 mm Aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) & fixing clip of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed. |
| 33 | S&F mild steel sliding door bolt plate type black jappaned with bright bolt not less than 12 mm dia with and including 6 bolts and nuts four o bolt plate and two on staple 250 mm long |
| 34 | S&F mild steel butt hinges heavy weight cold rolled 125mm size |
| 35 | S & F 200 mm long mild steel barrel tower bolts, stove enamelled black, with bright bolt. |
| 36 | S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised. |
| 37 | S&F 250 mm Stainless steel , sliding door bolts with hasp, staple (bolt type) & fixing clip of sheet, rates including necessary screws complete all as specified and as directed by Engr-in-Charge. |
| 38 | S & F in hasp and staple of size 125 mm, safety type, aluminium anodised with mild steel hinge pin including bolt to hing plate and fixed with screws. |
| 39 | S&F in repair ordinary rat tails 300 mm size pattern door springs including roller and roller plate complete. |
| 40 | S&F in repair 75 mm length floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring Fixed in floor |
| 41 | S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40mm and fixed with stainless steel wire staples including supply & fix second class hard wooden fillet, wrought , cross sectional area exceeding 3 Sqcm but n.exc 6 Sq cm fixed with nails complete all as directed. |
| 42 | S&F in repair stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40mm and fixed with stainless steel wire staples including supply & fix second class hard wooden fillet, wrought , cross sectional area exceeding 3 Sqcm but n.exc 6 Sq cm fixed with nails for wooden door/ window & for steel / aluminium widor/door with iron staples/aluminium bedding complete all as directed. |
| 43 | S&F powder coating anodised aluminium section for shutter/frame for door, window and ventilator complete all as specified. |
| 44 | S&F factory made ‘Z’ type section steel window with side hung shutters including box type hinges of 50 mm size with steel handles and peg stay & 02 Nos , 100 mm size MS tower bolt welded on each shutter complete with glazing bars dovetailed or welded complete all as specified |
| 45 | All same as per item No 44 here-in-above but without glazing bars -do - |
| 46 | S&F factory made steel ventilators with top hung shutters including hinges, steel peg stay , towerbolt etc complete all as specified |
| 47 | S&F factory made steel windows or ventilators fixed type , with glazing bars complete all as specified |
| 48 | S&F powder coating Anodised aluminium window and ventilator shutters, sliding type two or three tracks without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, aluminium fittings like locking system complete all as specified and directed by Engineer-in-Charge.(Thickness of powder coating not less than 50 micron) complete all as specified and as directed. |
| 49 | S & F 1.25mm thick mild steel, plain, black sheet in wall cladding, steel gates, etc., cut to size, holes punched including rounded headed screws, clout nails or revets and fixed to wood or steel framing or fixing to MS clamps with necessary bolts and nuts with plain 40mm lap joints welded to frame as directed. |
| 50 | S & F in repair 1.25mm thick mild steel, plain, black sheet in wall cladding, steel gates, etc., cut to size, holes punched including rounded headed screws, clout nails or revets and fixed to wood or steel framing or fixing to MS clamps with necessary bolts and nuts with plain 40mm lap joints welded to frame as directed. |
| 51 | S&F rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats, necessary welding etc. conforming to Grade E-250 quality ‘A’ all as specified and as directed. |
| 52 | S&F mild steel framed work as in doors, gates, steel frames, chowkats, etc. of angle or other section with gusset plates, rails, braces, etc., complete conforming to Grade E-165 (Fe 290), drilled for fixing of steel sheeting or other covering including necessary welding etc and fixing in position complete all as specified and as directed. |
| 53 | S&F mild steel framed work as in grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors and similar work including welding conforming to Grade E-165 (Fe 290), complete, all as specified & directed |
| 54 | S&F Anodised aluminium snap grid frame work size 605x605 mm for false ceiling incl Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long all as specified & directed by Engr -in-charge |
| 55 | S&F pre-painted galvalume (zincalume) aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof coverings/cladding to walls fixed with self tapping screws as specified. |
| 56 | Supply and fix Pre- painted galvalume aluminum zinc coating GI plain sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or L type or J type or cranked hook bolts or as per manufacture instruction all as specified and as directed. |
| 57 | M &L Roof tiles, Mangalore pattern, interlocking at side joints, laid dry all as completed |
| 58 | M&L or hip tiles to suit Mangalore pattern of roofing tiles, bedded and jointed in cement mortar 1:6 all as specified |
| 59 | M & L Non asbestos fibre cement building boards 4 mm thick (one side embosed design), fixed or laid/ inserted to Aluminium grid frame work in ceiling with clips all as specified and directed. |
| 60 | M & L for 75 mm thick plain cement conctere 1: 3 : 6 type C2 using 40 mm graded crushed stone aggregate as in plinth protection finished the surface fair and even complete all as directed. |
| 61 | M & L for 75 mm thick plain cement concrete 1:4:8 type D2 using 40 mm graded crushed stone aggregate as in sub base of floor/ foot path etc and finished the surface complete all as directed. |
| 62 | M&L for 25 mm thick plain cement concrete 1:2:4 type B0 using 12.5 mm graded crushed stone aggregate as in floor and finished the surface suitable to receive floor tiles complete all as directed. Please Enable Macros to View BoQ information |
| 63 | M&L for 25 mm thick plain cement concrete 1:2:4 type B0 using 12.5 mm graded crushed stone aggregate as in floor and finished the surface suitable to receive floor tiles complete all as directed. Please Enable Macros to View BoQ information |
