|
| 1 | Taking down copper/aluminium point wiring(light,fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting holder etc. removing materials to store for keeping in safe custody or for taking credit(credit for above items should be made as per conitions separately) and making good distrubed surfaces of walls, floors etc. |
| 2 | Taking down only old u/s items such as normal/modular tupe switches, Bell push, call bell, ceiling rose, sockets, switch sockets, regulator, lamp holder etc by unscrewing from board carefully including making good of the disturbed surfaces, all as specified and directed. |
| 3 | M & L for Point wiring with PVC insulated unsheathed stranded copper conductor cable of size 1.5 Sqmm, with PVC insulated unsheathed stranded copper conductor cable of size 1 Sqmm stranded for earth continuity wire, to be drawn in and including, PVC medium grade surface casing capping not less then 20 mm width with MS sheet metal sunken switch/Terminal box 1.2 mm thick and ebonite switch board cover 3.0 mm thick or PVC moulded switch board and brass screws with cup washers including all necessary wall cutting and making good disturbed surface all as directed and specified .Note : Cutting chases and making good to match with the adjoining surface shall be included in the unit rate. |
| 4 | (a) One light point controlled by one, one way switch |
| 5 | (c) One 3 pin 5 amp socket out point on the same board with other switches. |
| 6 | (d) One3 pin 5 amps socket out let point on independent board |
| 7 | All as per same in item No 03 above but for one socket outlet 15 amp on independent board with 2.5 Sq. mm cable and 1.5 Sq.mm. earth wire complete all as specified and directed. |
| 8 | S &F Switch piano flush type single pole one way 5 amps complete all as specified and directed. |
| 9 | S&F bell push switch fiush type 5 amp complete all as specified and directed. |
| 10 | S &F Socket out let 2 in one, 5/3 pin 5Amp complete all as specified and directed. |
| 11 | S &F Switch socket combination 5 Amps 5 pin flush type complete all as specified and directed. |
| 12 | S &F Switch socket combination 5 in 1, 5 pin 5/15 Amps flush type universal complete all as specified and directed. |
| 13 | S &F Ceiling rose, surface bakelite 65x50 mm three terminal complete all as specified and directed. |
| 14 | S&F BELL ding dong AC 230 volt single pole complete all as specified and directed. |
| 15 | S &F Lamp holder, PVC/Polycarbonate type insulated body with back plate for angle holder suitable for fixing of LED Bulbs of any wattage 230 Volts all as per specified. |
| 16 | M & L MODULAR(GANG BOX) Switch socket outlet 3 pin 5 amp' flush type |
| 17 | M & L MODULAR(GANG BOX) Switch socket outlet 3 pin, 15 amp, flush type |
| 18 | S &F in replacement inverter LED bulb/lamp of Watts Cool Daylight with following specifications:-Power Consumption-12 W,Base Type-B22,Light Color-Cool Day Light (6500K), Battery TypeBuilt-in Li-ion, Battery Backup-Up to 4 hours, Charging Time of 8–10 hours Surge Protection -Up to 4kV and Voltage Protection-Up to 360V al specified and directed by engineer in charge. |
| 19 | S&F in replacement Power saving LED light fitting, 9 Watt, 2 feet (Approx), 230 Volt complete all as specified and as directed. |
| 20 | S &F in replacement inverter LED tubelight of 20 Watts Cool Daylight with following specifications:- IS Standard IS 10322 (Part-5/Sec-1), System wattage* 20W, Rated Voltage 230V AC, Operating Voltage Range 140V~270V, Frequency 50Hz, System Current <102mA, Power Factor ≥0.95, System Lumen Efficacy** 100lm/W, CCT (As per ANSI) 6500K, CRI ≥80, THD ≤30%, Driver Efficiency ≥80%, Main Housing Material: PC, Front Cover: PC Diffuser, LED LM80 certified LED, LED Lumen Maintenance 50,000 hours @ L70 as per LM80 report of LED, Control Gear Electronic, CC driver, Internal Wiring Insulated Cu wire, Hardware SS & MS Zinc plated and passivated, Ingress Protection IP20, Operating Temperature -10ᵒC~ 50ᵒC, Operation/Inverter Function Switch ON – Light ON-Inverter function auto enable, Switch OFF- Light OFF, Inverter Load Operation 40-50% of rated system wattage for 2-3 Hours operation at STC battery fully charged, Battery Used 3.7V 3600mAH (2*1800mAH) Li-ion Battery pack, Tolerance ±10% |
| 21 | S &F in replacement inverter LED 2X2 light of 35/36 Watts Cool Daylight with following specifications:- IS Standard IS 10322 (Part-5/Sec-1), System wattage* 36W, Rated Voltage 240V AC, Operating Voltage Range 140V~270V, Frequency 50Hz, System Current <183mA, Power Factor ≥0.95, System Lumen Efficacy** 100lm/W, CCT (As per ANSI) 6500KCRI ≥80, THD ≤10%, Driver Efficiency ≥85%Main Housing Material: Duly powder coated CRCA sheet steel, Front Cover: PMMA, LED LM80 certified LED, LED Lumen, Maintenance 50,000 hours @ L70 as per LM80 report of LED, Control Gear Electronic, CC driver, Internal Wiring Insulated Cu wire, Hardware SS & MS Zinc plated and passivated, Ingress Protection IP20, Operating Temperature -10ᵒC~ 50ᵒC, Operation/Inverter Function Switch ON – Light ON and Inverter function enable, Switch OFF- Light OFF, Inverter Load Operation 20-30% of rated system wattage for 1.5-2.5 Hours operation at STC battery fully charged, Battery Used 3.7V Li-ion BatteryTolerance ±10% |
| 22 | Taking down old and UNSV DBs SPN/TPN complete with MCB TPN/SPN/SP complete all as specified and as directed |
| 23 | S&F in repair MCB DB 8 Way Sheet metal enclosure factory made for DBs single pole and neutral double door 240 volts with 200 Amps rated bus bar fixed on walls, including dressing and connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning and making good of wall, surfaces all as specified and directed. |
| 24 | S&F in replacement MCB,DP 415 Volts , 40-63 Amps all as specified and as directed. |
| 25 | S&F in replacement MCB SPN, 240 Volts , 32-40 Amps all as specified and as directed |
| 26 | S&F in replacement MCB, TPN, 415 Volts , 63 Amps all as specified and as directed. |
| 27 | S&F in replacement MCB singal pole 240 Volts , 6 to 32 Amps all as specified and as directed. |
| 28 | S&F in repair PVC insulated, 1.50 Sqmm, single core, copper conductor, FRLS complete all as specified and as directed. |
| 29 | S&F in repair PVC insulated, 2.50 Sqmm, single core, copper conductor, FRLS complete all as specified and as directed. |
| 30 | S&F in repair PVC insulated, 4.0 Sqmm, single core, copper conductor, FRLS complete all as specified and as directed. |
| 31 | S&F in repair PVC insulated, 6.0 Sqmm, single core, copper conductor, FRLS complete all as specified and as directed. |
| 32 | S&F in repair PVC insulated, 10.0 Sqmm, single core, copper conductor, FRLS complete all as specified and as directed. |
| 33 | Material and labour for sub main wiring complete with 2 run of 6 sqmm, single core, copper conductor cable 1100 volts grade, FRLSH type, PVC insulated, unsheathed, flexible, multi stranded duly colour coded cable drawn through and including PVC conduit of size 25mm width or above as required at site and accessories such as tee, corners,overlaping connector etc of suitable size including concealed in walls/roofs/ ceilings/floors etc and including 01 run of 6 sqmm single core, copper conductor cable 1100 volts grade, FRLSH type, PVC insulated, unsheathed, flexible, multi stranded of green colour as earth continuity conductor connected to common earth dolly and including making good the disturbed surfaces to match with existing surface and colour shade including removing old unserviceable item complete all as specified and directed.Note : - Two run of 6.0 sqmm cable and one run of 6.0 sqmm cable and one run of PVC conduit concealed in walls/roofs/ ceilings/floors etc will be measured as one unit. |
| 34 | Material and labour for sub main wiring complete with 2 run of 4 sqmm, single core, copper conductor cable 1100 volts grade, FRLSH type, PVC insulated, unsheathed, flexible, multi stranded duly colour coded cable drawn through and including PVC conduit of size 25mm width or above as required at site and accessories such as tee, corners,overlaping connector etc of suitable size including concealed in walls/roofs/ ceilings/floors etc and including 01 run of 4 sqmm single core, copper conductor cable 1100 volts grade, FRLSH type, PVC insulated, unsheathed, flexible, multi stranded of green colour as earth continuity conductor connected to common earth dolly and including making good the disturbed surfaces to match with existing surface and colour shade including removing old unserviceable item complete all as specified and directed.Note : - Two run of 4.0 sqmm cable and one run of 4.0 sqmm cable and one run of PVC conduit concealed in walls/roofs/ ceilings/floors etc will be measured as one unit. Please Enable Macros to View BoQ information |
