|
| 1 | Civil Work BuildingEarth work in excavation in foundation trenches in Ordinary soil ….do …..do…do all complete jobs . |
| 2 | Extra for earthwork in hard soil as per specification and direction of E/I. ( vide classification of soil item-B) |
| 3 | Earth filling in foundaion trenches and plinth in layers not exceding 150 mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I. (mode of measurement compacted volume) |
| 4 | Providing coarse clean sand filling in foundation Trenches……do.. …do…..do all complete jobs. |
| 5 | Providing designation 75B one brick flat soiling …….do .. …..do……do all complete jobs. |
| 6 | Providing PCC M150 with mix(1:2:4) in foundation and plinth do………do…..all complete job. |
| 7 | Providing and laying in position specific grade of RCC M20(1:1:5:3) exluding the cost of centering and shuttering all work up to plinth level. |
| 8 | Providing R.C.C. M-200 with nominal mix of (1:1:5:3) in columns ………….do…………. and direction of E/l. |
| 9 | Providing designation 75B Brick work in CM (1:6) in foundation and plinth ……………..do………….. and direction of E/l. |
| 10 | Providing R.C.C. M-200 with nominal mix of (1:1:5:3) in lintel ,chujja,roof beam……………..do……………...and direction of E/l. |
| 11 | Providing tor steel reinforcement of 10mm,12mm,16mm, dia rods ………………..do………... and direction of E/l.8 mm,10 mm , 12 mm dia barA-8mm dia rod20% of total amount |
| 12 | B-10mm dia rod50% of total amount |
| 13 | C-12mm,16mm dia30% of total amount |
| 14 | Providing designation 75A B/W in C.M (1:6) in super structure …..do…do…do all complete job. |
| 15 | Providing designation 125 mm thick reinforced designation 75A brick work in CM (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 25 including the cost of screening, carriage of materials, scaffolding , raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I. |
| 16 | Centering and shuttering including strutting proping etc and removal of form for foundation, footing, base of coulmn etc. |
| 17 | Centering and shuttering including strutting proping etc and removal of form for coulmn etc. |
| 18 | Centering and shuttering including strutting proping etc and removal of form for lintel,beam,plinth beam etc. |
| 19 | Centering and shuttering including strutting proping etc and removal of form for roof etc. |
| 20 | Centering and shuttering including strutting proping etc and removal of form for chujja etc. |
| 21 | Providing 16MM Dia 1M long Fan Hook …do…do…do all complete. |
| 22 | Supplying Fitting and Fixing M.S grill of 20*6mm M.S Flate as per approved design and drawing….do… ...do….all complete as per specification and direction of E/I. |
| 23 | Supplying, fitting and fixing 35mm thick solid core type non-decorative single leaf flush door shutter in door and windows with black board core blended with high quality phenol formal dehydes synthetic resine both side commercial veneered of standard make with oxidised iron fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I. |
| 24 | Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : (50x20)mm |
| 25 | Providing and fixing bright finished brass 100 mm mortice latch and lock ISI marked with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc., complete. |
| 26 | Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : Twin rubber stopper |
| 27 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm) with double speed adjustment with necessary accessories and screws etc. complete. |
| 28 | Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately). |
| 29 | Supplying fitting and fixing glass panes including supplying putty. Beads and nails after taking out old and broken glass panes and disposal of debris all complete as per building specification and direction of E/I.5.5 mm plain |
| 30 | Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite Slab over .50 sqm of any colour and shape area |
| 31 | Providing edge moulding to 18mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. |
| 32 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/Granite / stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. |
| 33 | Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size)as per direction of Engineer-in-charge and finished smooth. |
| 34 | Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm . |
| 35 | Providing and laying 25mm thick kotah stone tiles in risers of steps skirting and pillars of approved size texure and colour laid over 12mm thick cement mortar (1;30 and joined with grey cement slurry mixed with pigment to match the shade of the slab including rub bing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 36 | Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointing with white cement including rubbing, polishing and cost of curring taxes and royalty all complete as per building specification and direction and E/I.With A Grade White Tiles |
| 37 | Providing 250mm. Wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 250mm apron including cost of eartwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I. |
| 38 | Providing 12 mm thick C.P (1:6) in all wall……do….do……do all complete job. |
| 39 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 40 | Providing 6 mm thick cement plaster with CM (1:4) in ceiling do - do all complete job. |
| 41 | Providing 19MM water proof cement plasterin CM (1:3) Over Roof……do……do…..all complete as per specification and direction of E/I. |
| 42 | Providing two coat of synthetic enamel paint over a primer coat of red lead paint of approved shade and make over new steel surface…do…..do….all complete as per specification and direction of E/I. |
| 43 | Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm). |
| 44 | Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by the rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification and direction of E/I. |
| 45 | Carriage of Materials(i) Bricks-Lead(1US+59S) |
| 46 | (ii) Sand-Lead (1K+24S) KM |
| 47 | (iii) Stone Chips-Lead (1U+39S) KM |
| 48 | (v) (Cement +Steel)-Lead 5KM |
| 49 | Water Supply & Sanitation WorkSupplying, fitting and fixing viterous white glazed earthen ware I.W.C. of Parry Hindustan or any other I.S.S. approved make with 100 mm H.C.I., \\"p\\" trap 15 litres C.I.. or C. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings, C.I. or C.C. brackets 32 mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of viterous white glazed earthenware where footrest to be fixed in floor 15 mm C.I. body brass spindle stop cock of weight not less than 50 grms. 15 mm P.V.C. connection pipe 450 mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l.(C) 450 mm long(c) With 10 lit Low Level P.V.C Cistern |
| 50 | Supplying, fitting and fixing viterous white glazed earthen ware wash hand basin of Parry or Hindustan or any other I.S.S. approved make supported on pointed c.l. or R.S. brackets 32m C.I. brass waste 15mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350grms., 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/l. |
| 51 | Supplying, fitting and fixing white glazed fires clay sink of approved make with overflow arrangements supported on C.l. or R.S. painted brackets 40 mm dia C.P. brass waste with C.P. brass chain and rubber plug, 40 mm dia P.V.C. waste pipe about 750mm long with brass coupling at one end and 15 mm C.I. body brass spindle bib cock of approved quality of weight not less than 450 grms. including cutting wall and making good the same etc. all complete as per specification and direction of E/l.(a) Kitchen sink of size 600 mm x 450 mm x 250 mm |
| 52 | Providing and fixing PTMT bib cock of approved quality and colour. 15 mm nominal bore, 165 mm long. Weighing not less than 110 gms. |
| 53 | Providing and fixing 15mm size C.P brass pillar cock (Weight not less than 350 gms) C.I body brass spindle pillar cock of approved quality as per spcification and direction of E/l.(b) C.I. body brass spindle |
| 54 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc.20 mm nominal outer dia .Pipes. |
| 55 | 32 mm nominal outer dia .Pipes. |
| 56 | Providing and fixing Gun metal full way valve of approved qualtiy, all complete as per specification and direction of E/l(a) 20mm dia wt not less than 400 gms |
| 57 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 58 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i)Single socketed pipes.75MM DIA |
| 59 | 110MM DIA |
| 60 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion.(I) 110MM BEND |
| 61 | SHOE 110MM |
| 62 | Septik TankEarth work in excavation in foundation trenches in hard soil do - do all comp. job. |
| 63 | Extra for earthwork in hard soil as per specification and direction of E/I. ( vide classification of soil item-B) |
| 64 | Providing coarse clean sand in filling in foundation trenches as per building specification and direction of E/I |
| 65 | Providing designation 75B one brick flat soling joints filled with local sand do - do all comp. job. |
| 66 | Providing PCC M-15 (1:2:4) in fdn do - do all complete job. |
| 67 | Providing designation 75B one brick work in CM (1:6) in foundation do - do all comp. job. |
| 68 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size) |
| 69 | Providing RCC M-20 (1:1.5:3) in slab do - do all complete job. |
| 70 | Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform |
| 71 | Providing 8 mm Tor steel reinforcement do - do all complete job. |
| 72 | Providing 12 mm thick plaster in CM (1:3) in inner & outer do - do all complete job. |
| 73 | Providing 1.50mm cement punning do do all comp. job. |
| 74 | Carriage of MaterialsSteel (lead 5 Km) |
| 75 | Cement (lead 5 Km) |
| 76 | Sand lead -(1K+24S) Km |
| 77 | S/Chips lead-(1US+39S) Km |
| 78 | Bricks -lead( 1US+59S)Km |
| 79 | ElectrificationPoint wiring in PVC Conduit with modular switch:- Wiring for light/fan point /exhaust fan point /call bell with 1.5 sqmm .FRPVC insulated copper conductor single core cable in surface /recessed pvc conduit with modular type switch.Group C |
| 80 | Wiring for Curcuit Submain wiring along with earth wire the following sizes of pvc insulated copper conductor single core cable in surface of recessed pvc conduit as required2x1.5 sqmm+1x1.5 sqmm earth wire |
| 81 | 2x2.5 sqmm+1x2.5 sqmm earth wire |
| 82 | 2x4.0 sqmm+1x4.0 sqmm earth wire |
| 83 | Supplying and fixing of following size PVC conduit along with accessories in surface/recess including cutting the wall do--do-- E/I25mm |
| 84 | Supplying and fixing PVC/G.I box of following size on surface or recess with suitable size do--do-- E/I |
| 85 | Supplying and fixing following modular type switch socket on the eixsting modular plate and switch box.do--do--E/I5/6 amps one way switch |
| 86 | 5/6,3pin socket outlet |
| 87 | Supplying and fixing following size /modular box along with modular base and cover plate for modular swiches do--do--1 or 2 modular |
| 88 | 4 or 5 modular |
| 89 | 6 modular |
| 90 | Supplying and fixing 2 pin 5 amp ceilling rose do--do-- |
| 91 | Supllying and fixing batten/angle holder do--do-- |
| 92 | Supplying 1200 mm Ceilling Fan Bajaj/ Cromtion or any other approved make etc |
| 93 | Supplying and fixing MCB |
| 94 | S/F/F 25 watt L.E.D street ligh fitting complete |
| 95 | S/F/F 9/10 Watt LED bulb do--do--All complete Job. |
| 96 | Gate & Guard RoomEarth work in excavation in foundation in hard soil ….do …..do…do all complete jobs . |
| 97 | Extra for earthwork in hard soil as per specification and direction of E/I. ( vide classification of soil item-B) |
| 98 | Providing coarse clean sand filling in foundation ……do.. …do…..do all complete jobs. |
| 99 | Providing designation 75B one brick flat soiling …….do .. …..do……do all complete jobs. |
| 100 | Providing PCC M150 with mix(1:2:4) in foundation and plinth do………do…..all complete job. |
| 101 | Providing RCC M-200 in nominal mix of ( 1:1.5:3) in foundation …do….do…do all complete jobs . |
| 102 | Providing RCC M-200 with nominal mix of ( 1:1.5:3) in Tie Beam…do….do…do all complete jobs . |
| 103 | Providing RCC M-200 in nominal mix of (1:1.5:3) in wall Beam….do…..do…..do all complete jobs . |
| 104 | Centering and shuttering including strutting proping etc and removal of form for foundation, footing, base of coulmn etc. |
| 105 | Centering and shuttering including strutting proping etc and removal of form for coulmn etc. |
| 106 | Centering and shuttering including strutting proping etc and removal of form for lintel,beam,plinth beam etc. |
| 107 | Centering and shuttering including strutting proping etc and removal of form for roof etc. |
| 108 | Providing designation 75B B/W in C.M (1:6) in super structure …..do…do…do all complete job. |
| 109 | Providing 12 mm C.P (1:6) ……do….do……do all complete job. |
| 110 | Providing 6 mm thick plaster in CM (1:4) in ceiling do - do all complete job. |
| 111 | Providingand Laying 25mm thick Kota Stone Tiles do …... do………. all complete job. |
| 112 | Providing Tor steel reinforcement do……..do……. all complete as per building specification and direction of E/l.A-8mm dia rod20% of total amount |
| 113 | B-10mm dia rod50% of total amount |
| 114 | C-12-16mm dia30% of total amount |
| 115 | Supplying, fitting and fixing M.S. grill gate do…..do…... all complete as per drawing specification and direction of E/l. |
| 116 | Providing two coats of painting with ready mixed paint of approved shade do……do…..all complete as per building specfication and direction of E/l. |
| 117 | Carriage Cost of MaterialsCement + steel (Lead – 5 S km) |
| 118 | Sand (Lead – 1k+24S km) |
| 119 | Stone chips (Lead – 1US+39S km) |
| 120 | Bricks (Lead - 1US+59S km) |
| 121 | GST @ 18% |
| 122 | Labour cess @ 1% Please Enable Macros to View BoQ information |
