|
| 1 | Staff Quarter at PanchtarniEarth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed by EIC. All Kinds of soil |
| 2 | P/L of dry nallah soling tightly hand packed i/c carriage charges and headload charges complete job. |
| 3 | Providing and laying in position cement concrete of specified grade Of 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone agg.40 mm nominal size excluding cost of centering and Shuttering all work up to plinth . |
| 4 | Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 5 | Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement.: 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 6 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 7 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 8 | PROVIDING AND FIXING EXPOSED QUALITY SHUTTERING INCLD cost of all fittings complete using KITPLY/STEEL sheets complete job |
| 9 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes I/C ALL CARRIAGES |
| 10 | Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of steel primer all complete. |
| 11 | Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in-charge. (Cost of aluminum snap beading shall be paid in basic item.) With floating glass panes of 3.5 mm thickness |
| 12 | Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z-sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws,tower bolts , handles , sliding mechanism all complete as per architectural drawings and the directions of Engineer-in-Charge :Powder coated aluminum (minimum thickness of powder coated 50 microns) |
| 13 | Providing and fixing of 4 mm thick Aluminum Pannel Sheet both sides laminated including carriages all job complete as per the directions of EIC. |
| 14 | P/F P.U.F sandwiched panels in walls with tongue and groove fitting: 60 mm thick (size , color etc as recommended by engineer in charge) complete i/c all carriages |
| 15 | P/F P.U.F sandwiched panels in walls with tongue and groove fitting: 40 mm thick (size , color etc as recommended by engineer in charge) complete i/c all carriages |
| 16 | Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. 50 mm thick with 20mm nominal size stone aggregate.complete. |
| 17 | P/F track deck crill make or equivalent H.I rib profiled sheets 1000 to 1020mm cover width 28-35mm high crests at 250 to 255mm TCT (total coated thickness) high tensile SMP Galvalume steel with silicon modified ployester coating of approved colour of total thickness of 35 micron comprising 20 micron exterior coat of SMP over 5 micron polyester back coat over 5 micron primer coats on both surfaces incld. side and end lap and using 8mm galvalume hex self drilling fastener on each crest of sheet for connection with purlins and seam bolts at 300mm centers on all side and end lapps etc. (measured for unit of laid area)0.50mm THICK (TATA, JSW COLORON PLUS OR EQ) I/C ALL CARRIAGES. |
| 18 | Providing and fixing plained eaves boarding of 2nd class kail wood 250x32 mm (nominal size ) including synthetic enamel paint (two coats ) over primer coat. |
| 19 | Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, and polishing to edges to give high gloss finish etc. complete at all levels (Area of slab over 0.5 sqm) : 18 mm Granite |
| 20 | Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. (Granite Work) |
| 21 | Providing and laying Anti Skid Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand and manufacturer, in all colours and shades, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS:15477, in average 6 mm thickness, including grouting of joints (Paymentfor grouting of joints to be made separately).Size of tile 600x600 mm |
| 22 | Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling /grouting and finishing complete as per direction of Engineer-in-charge |
| 23 | P/F of 12mm thick imported wood paneling (newzealand pine or equivalent) of approved pattern overand including base of 10mm thick plywood finishing exposed surface with two of more coats of touch wood and polish including cost of nails, adhesive material etc. and all carriages |
| 24 | Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required.White vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. |
| 25 | Providing and fixing pedestal supported wash basin with C.I. brackets,including painting of fittings and brackets, cutting and making good the walls wherever required : White Vitreous China Wash basin size 630x450 mm (approved make) |
| 26 | Providing and fixing of mirror with built in shelf of superior quality (approved make) with all fittings and fixtures complete. |
| 27 | Providing and fixing G.I. Pipes complete with G.I. fittings and clamps (approved MAKE, TYPE-B ) i/c making good the walls etc. concealed pipe including painting with anticorrosive bitumastic paint, cutting chases and making good the wall :15 mm dia. nominal bore |
| 28 | Providing and fixing G.I. Pipes complete with G.I. fittings and clamps approved MAKE, TYPE-B) i/c making good the walls etc. concealed pipe including painting with anticorrosive bitumastic paint, cutting chases and making good the wall :20 mm dia. nominal bore |
| 29 | Providing and fixing C.P. brassbib cock of approved quality (Approved make) conforming to IS standards:15 mm dia. nominal bore |
| 30 | Providing and fixing C.P. angle cock of approved quality (Approved make) conforming to IS standards:15 mm dia. nominal bore |
| 31 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked( HEAVY DUTY) with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank |
| 32 | Providing and fixing ball valve approved quality conforming to IS standards:20 mm dia. nominal bore |
| 33 | Providing and fixing of Towel rail of superior quality with all fittings and fixtures complete |
| 34 | Providing and fixing MS grating of approved quality and colour. 100 mm nominal dia. |
| 35 | Providing and fixing Polyvinyl Chloride (PVC) pipes( TYPE-B HEAVY DUTY), incl all PVC plain fittings This includes jointing of pipes ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge.a) 100mm |
| 36 | b) 75mm |
| 37 | Constructing masonry main holes 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) with inside plastering with cement mortar 1:3 (1 cement :3 coarse sand) 12mm thick finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5. complete job |
| 38 | Providing and fixing of soap dish holder (approved make) with concealed fittings etc. |
| 39 | P/F Hot water geyser (50 ltr capacity) of approved design and make i/c all fittings complete |
| 40 | P/F Basin Mixer of standard make(approved make) as per specifications complete |
| 41 | P/F sink Mixer of standard make(approved make) as per specifications complete |
| 42 | P/F wall Mixer of standard make(approved make) as per specifications complete |
| 43 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink without drain board 610x510mm bowl depth 200mm |
| 44 | Construction of cement ring type septic tank / soakage pit (ring size 1000mm) , lowering of rings and fixing of top precast cap i/c earthwork etc complete job as per directions of engineer in charge (16 No per pit) |
| 45 | carriage of material using mech tpt for an av. lead of 75 kms (Ganderbal to Baltal)Sand/Bajree |
| 46 | HEADLOAD of material using ponys/manual labour for an av. lead QVI ITEM 3-6 FOR [email protected] PER KM PER BAG |
| 47 | QVI ITEM 3-6 FOR SAND/BAJREE @RS.170 PER KM PER CUM |
| 48 | STEEL TMT BARS QVI NO [email protected] PER KM PER KG |
| 49 | STR STEEL QVI NO [email protected] PER KM PER KG |
| 50 | COLOR COATED GS SHEETS QVI NO 18(165.86 sqm @5.47kg/Sqm =907.25kg @RS.3PER KM PER |
| 51 | PUF Panels QVI NO 14-15 @RS.75 PER KM PER SQM |
| 52 | PROVISION FOR OTHER CONSTRUCTION [email protected] PER KM PER TRIP |
| 53 | Staff Quarter at SheshnagEarth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed by EIC. All Kinds of soil |
| 54 | P/L of dry nallah soling tightly hand packed i/c carriage charges and headload charges complete job. |
| 55 | Providing and laying in position cement concrete of specified grade Of 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone agg.40 mm nominal size excluding cost of centering and Shuttering all work up to plinth . |
| 56 | Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 57 | Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement.: 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 58 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 59 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 60 | PROVIDING AND FIXING EXPOSED QUALITY SHUTTERING INCLD cost of all fittings complete using KITPLY/STEEL sheets complete job |
| 61 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes I/C ALL CARRIAGES |
| 62 | Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of steel primer all complete. |
| 63 | Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in-charge. (Cost of aluminum snap beading shall be paid in basic item.) With floating glass panes of 3.5 mm thickness |
| 64 | Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z-sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws,tower bolts , handles , sliding mechanism all complete as per architectural drawings and the directions of Engineer-in-Charge :Powder coated aluminum (minimum thickness of powder coated 50 microns) |
| 65 | Providing and fixing of 4 mm thick Aluminum Pannel Sheet both sides laminated including carriages all job complete as per the directions of EIC. |
| 66 | P/F P.U.F sandwiched panels in walls with tongue and groove fitting: 60 mm thick (size , color etc as recommended by engineer in charge) complete i/c all carriages |
| 67 | P/F P.U.F sandwiched panels in walls with tongue and groove fitting: 40 mm thick (size , color etc as recommended by engineer in charge) complete i/c all carriages |
| 68 | Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. 50 mm thick with 20mm nominal size stone aggregate.complete. |
| 69 | P/F track deck crill make or equivalent H.I rib profiled sheets 1000 to 1020mm cover width 28-35mm high crests at 250 to 255mm TCT (total coated thickness) high tensile SMP Galvalume steel with silicon modified ployester coating of approved colour of total thickness of 35 micron comprising 20 micron exterior coat of SMP over 5 micron polyester back coat over 5 micron primer coats on both surfaces incld. side and end lap and using 8mm galvalume hex self drilling fastener on each crest of sheet for connection with purlins and seam bolts at 300mm centers on all side and end lapps etc. (measured for unit of laid area)0.50mm THICK (TATA, JSW COLORON PLUS OR EQ) I/C ALL CARRIAGES. |
| 70 | Providing and fixing plained eaves boarding of 2nd class kail wood 250x32 mm (nominal size ) including synthetic enamel paint (two coats ) over primer coat. |
| 71 | Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, and polishing to edges to give high gloss finish etc. complete at all levels (Area of slab over 0.5 sqm) : 18 mm Granite |
| 72 | Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. (Granite Work) |
| 73 | Providing and laying Anti Skid Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand and manufacturer, in all colours and shades, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS:15477, in average 6 mm thickness, including grouting of joints (Paymentfor grouting of joints to be made separately).Size of tile 600x600 mm |
| 74 | Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling /grouting and finishing complete as per direction of Engineer-in-charge |
| 75 | P/F of 12mm thick imported wood paneling (newzealand pine or equivalent) of approved pattern overand including base of 10mm thick plywood finishing exposed surface with two of more coats of touch wood and polish including cost of nails, adhesive material etc. and all carriages |
| 76 | Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required.White vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. |
| 77 | Providing and fixing pedestal supported wash basin with C.I. brackets,including painting of fittings and brackets, cutting and making good the walls wherever required : White Vitreous China Wash basin size 630x450 mm (approved make) |
| 78 | Providing and fixing of mirror with built in shelf of superior quality (approved make) with all fittings and fixtures complete. |
| 79 | Providing and fixing G.I. Pipes complete with G.I. fittings and clamps (approved MAKE, TYPE-B ) i/c making good the walls etc. concealed pipe including painting with anticorrosive bitumastic paint, cutting chases and making good the wall :15 mm dia. nominal bore |
| 80 | Providing and fixing G.I. Pipes complete with G.I. fittings and clamps approved MAKE, TYPE-B) i/c making good the walls etc. concealed pipe including painting with anticorrosive bitumastic paint, cutting chases and making good the wall :20 mm dia. nominal bore |
| 81 | Providing and fixing C.P. brassbib cock of approved quality (Approved make) conforming to IS standards:15 mm dia. nominal bore |
| 82 | Providing and fixing C.P. angle cock of approved quality (Approved make) conforming to IS standards:15 mm dia. nominal bore |
| 83 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked( HEAVY DUTY) with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank |
| 84 | Providing and fixing ball valve approved quality conforming to IS standards:20 mm dia. nominal bore |
| 85 | Providing and fixing of Towel rail of superior quality with all fittings and fixtures complete |
| 86 | Providing and fixing MS grating of approved quality and colour. 100 mm nominal dia. |
| 87 | Providing and fixing Polyvinyl Chloride (PVC) pipes( TYPE-B HEAVY DUTY), incl all PVC plain fittings This includes jointing of pipes ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge.a)100mm |
| 88 | b) 75mm |
| 89 | Constructing masonry main holes 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) with inside plastering with cement mortar 1:3 (1 cement :3 coarse sand) 12mm thick finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5. complete job |
| 90 | Providing and fixing of soap dish holder (approved make) with concealed fittings etc. |
| 91 | P/F Hot water geyser (50 ltr capacity) of approved design and make i/c all fittings complete |
| 92 | P/F Basin Mixer of standard make(approved make) as per specifications complete |
| 93 | P/F sink Mixer of standard make(approved make) as per specifications complete |
| 94 | P/F wall Mixer of standard make(approved make) as per specifications complete |
| 95 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink without drain board 610x510mm bowl depth 200mm |
| 96 | Construction of cement ring type septic tank / soakage pit (ring size 1000mm) , lowering of rings and fixing of top precast cap i/c earthwork etc complete job as per directions of engineer in charge (16 No per pit) |
| 97 | carriage of material using mech tpt for an av. lead of 65 kmsSand/Bajree |
| 98 | HEADLOAD of material using ponys/manual labour for an av. lead QVI ITEM 3-6 FOR [email protected] PER KM PER BAG |
| 99 | QVI ITEM 3-6 FOR SAND/BAJREE @RS.170 PER KM PER CUM |
| 100 | STEEL TMT BARS QVI NO [email protected] PER KM PER KG |
| 101 | STR STEEL QVI NO [email protected] PER KM PER KG |
| 102 | COLOR COATED GS SHEETS QVI NO 18(162.55 sqm @5.47kg/Sqm =907.25kg @RS.3PER KM PER |
| 103 | PUF Panels QVI NO 14-15 @RS.75 PER KM PER SQM |
| 104 | PROVISION FOR OTHER CONSTRUCTION [email protected] PER KM PER TRIP |
| 105 | ElectricWiring for lighting points/fan points/ exhaust fan points/call bell points with 1.5 sq mm FRLS PVC insulated flexible stranded copper conductor wires in recessed or surface medium class PVC conduit, with 240V 6A modular switch , modular plate and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable, etc. as required. (Havells/ Polycab/ Anchor/ Finolex/KEI/RR or eq. make ) excl. cost of conduit. I. Group A |
| 106 | II. Group B |
| 107 | III. Group C |
| 108 | Wiring for light/power plug points (15/16A heating points) with 2x4 sq mm FRLS PVC insulated flexible stranded copper conductor wires in recessed or surface medium class PVC conduit along with 1x4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing, etc. as required. (Maximum two points shall be connected on one circuit).(Havells/ Polycab/ Anchor/ Finolex/KEI/RR or eq. ) excl. cost of conduit |
| 109 | Supplying and fixing of suitable size GI box with modular plate and modular cover in front on surface or in recess, including providing and fixing of 6 pin 15/16 A modular socket outlet and 15/16A modular switch, connections, etc. as required. (Havells/ SSK/ Anchor/ ABB/Schneider or equivalent) |
| 110 | Supplying and fixing of suitable size GI box with modular plate and modular cover in front on surface or in recess, including providing and fixing of 2 no. 3 pin 5/6 A modular socket outlet and 2 no. 5/6A modular switch, connections, etc. as required. (Havells/ SSK/ Anchor/ ABB/Schneider or eq.) |
| 111 | Supplying and fixing of modular sockets/ indicators/switches on existing modular plate and switch box , incl. connections, etc. as required. (Havells/ SSK/ Anchor/ ABB/Schneider or equivalent) i.3 pin 5A - 10A socket. |
| 112 | ii. indicator. |
| 113 | Point wiring for 5A -10A socket out lets (computer points) with 2x2.5 sq mm (P+N)FRLS PVC insulated 660/1100volt grade flexible stranded copper conductor wires in recessed or surface conduiting system and earthing the point with 1 x 2.5 sq. mm single core copper wire (loop earthing),(Maximum two points shall be connected on one circuit).(Havells/ Polycab/ Anchor/ Finolex/KEI/RR or equivalent) excl. cost of conduit |
| 114 | Supply, installation, testing and commissioning of 12 Watt LED recessed/ mounted (round or square) Down lighters having aluminum body, minimum 100lm/w, average life 50000 hours, LM79 & LM80 test report should be from Govt. Approved NABL lab / Govt. Of India , Operating temperature -10`C to +45`C. The job includes replacement warranty of fixture if damaged/ burnt out what so ever reason for a period of two years reckoned from the date of successful commissioning/ handing over of site to the intending department. (Havells/ Philips/ Crompton/ Halonix/Wipro). Commercial series. |
| 115 | Supply, installation, testing and commissioning of 200-250 mm sweep shutter type exhaust fans, incl. cost of ceiling rose and making of space in walls/ windows as per site and necessary connections. (Havells/ Philips/ Crompton). |
| 116 | Supply, installation, testing and commissioning of 100Watt LED Flood lighting luminaries having aluminum body, minimum 100lm/w, the luminary housing should be aluminum and the luminary optics shall have a high efficiency with transmittance, average life 50000 hours, Operating temperature -10`C to +45`C. LM79 & LM80 test report should be from Govt. Approved NABL lab / Govt. Of India. The job includes replacement warranty of fixture if damaged/ burnt out what so ever reason for a period of two years reckoned from the date of successful commissioning/ handing over of site to the intending department. (Havells/ Philips/ Crompton/Wipro). |
| 117 | Supply, installation, testing and commissioning of 1 star 1200 mm sweep ceiling fans of Havells / Crompton Greaves/Bajaj/ Usha (Sample to be got approved), incl. cost of extension of GI rod (if required) and making of necessary connections. |
| 118 | Supply and fixing of two module stepped electronic fan regulator on the existing modular plate switch box, incl. connections but excluding modular plate etc. as reqd. |
| 119 | Supplying and fixing of modular blanking plates on existing modular plate and switch box ,excluding modular plate as required. |
| 120 | Wiring for sub mains along with earth wire in FRLS PVC insulated 660/1100 volt grade flexible stranded copper conductor wires in recessed or surface conduiting system, excl. cost of conduits(Havells/ Polycab/ Finolex/ Anchor/KEI/RR or equivalent). 2 x 2.5 sq.mm + 1x 2.5 sq. mm earth wire |
| 121 | 2 x 6 sq.mm + 1x 6 sq. mm earth wire |
| 122 | Supply and fixing of 4 way (4 + 12) Double door surface/ recess mounting , Horizontal type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs, excluding cost of MCBs and Incomer. . |
| 123 | Supply, installation, testing and commissioning of 5-32A single pole rating 240/415V, 10 KA “C” curve MCB of Legrand/ Havells/ L&T suitable for inductive load in the MCB distribution board complete with necessary connections. |
| 124 | Supply, installation, testing and commissioning of 32A/40A DP rating 240V, 10 KA “C” curve MCB of Legrand/ Havells/ L&T suitable for inductive load in the MCB distribution board complete with necessary connections. |
| 125 | Supply, installation, testing and commissioning of 63 A DP rating 240V, 10 KA “C” curve MCB of Legrand/ Havells/ L&T suitable for inductive load in the MCB distribution board complete with necessary connections. |
| 126 | Providing of chemical earthing as per IS standards by way of digging 8 feet pit then embedding 2.5 mtr. Long GI earthing electrode, 60 mm dia. Connecting the plate with main control board by 10 SWG Copper wire with 1/2” dia. Full thread brass nut and bolts and washers, refilling the pit with chemical compound. |
| 127 | Supply, laying, connecting and commissioning of 16 sq. mm PVC insulated twin core Aluminum (un armoured) LT cable , incl. cost of required al. thimbles duly crimped. (over head /under ground). |
| 128 | Supply and fixing of (25 mm dia./ 25 mm wide flat batten) medium class PVC conduits along with accessories, surface/ recessed in walls, including cutting of walls and making good the same or fixed with nails/clips or as required. |
| 129 | Supply, installation , testing and commissioning of 3 KVA Petrol run ultra silent portable inverter generator. The cost includes all carriages and all applicable taxes. Model no. (EU30i) Engine type .4 Stroke, single cylinder Rated output. 2.8KVA Fuel tank capacity. 12.5 Ltr. Fuel consumption. 1.25 ltr/ hour Please Enable Macros to View BoQ information |
